FTTX MICROLOOP ENCLOSURE - 7twenty
Transcript of FTTX MICROLOOP ENCLOSURE - 7twenty
FTTX MICROLOOP ENCLOSURE
The FTTx MicroLoop is a multifunctional enclosure deployed in the distributionnetwork. Equipped for mid-span access with integrated bare fibre loop storage theFTTx MicroLoop facilitates up to 4 drop cables either pre-connectorized or spliced.The splice tray accommodates a single PLC Splitter whether pre-connecotrized orbare fibre from 1:2 up to 1:8. A continuous gel seal incorporates cable entries and theenclosure seals to an IP68 rating. The FTTx MicroLoop Enclosure can be wall mountedand is suitable for placement in manhole chambers or boundary access points.
ML001 November 2018 Page 1 of 7
FTTX MICROLOOP ENCLOSURE ATTRIBUTES
o The design and material used for the FTTx MicroLoop Enclosure provides ruggedness required for FTTx mass deployment and is suitable for wall mount or placement inside underground chambers.
o Available with or without a barrel lock for security.
o Optional customer branding can be provided on the lid.
o The enclosure’s lid opens upward and contains a self supporting hinge to allow the lid to remain in the open position while accessing the inner cable assembly.
o The inner cable assembly can easily be removed for preparation and maintenance work away from the main body, for example: in wall mount applications.
o There is a continuous seal formed around the inner cable assembly to ensure IP68 sealing. The seal incorporates the master seal, as well as the cable entry seals. Cable entries are formed in the seal and ranges from 2-4mm or 4-6mm cable diameters.
o Cable fixation is achieved externally via cable tie points. Internally cables are secured via additional cable tie points and cable input / loop inputs have further aramid yarn fixing cones.
o The splice tray contains a splice bay for 10 off 2.4 x 45mm heat shrink splice protectors double stacked and a PLC splitter bay for either bare fibre or pre-connectorized 900µ PLC Splitter modules.
o The slice tray hinges upwards and remains in position allowing unhindered access to the loop storage tray. Once the splice tray is returned to the resting point, there are two clips securing the tray in place.
o The loop storage basket is designed to provide quick access to pack away the bare fibre loop with a capacity to store <70m of 250µm bare fibre.
o The inner enclosure assembly can only be fitted into the main body with the loop storage area facing towards the back. This provides protection to the primary looped fibre upon opening of the enclosure.
o The FTTx MicroLoop Enclosure was designed with a maximum fibre bend radius of 10mm and it is recommended for use with enhanced bend insensitive fibres such as G657.A1, G657.A2/B2.
o The drop cable entry side of the enclosure has two plate options. An adapter plate for 4 x SC simplex adapters (flangeless) or LC duplex or a bare fibre management plate.
ML001 November 2018 Page 2 of 7
FTTX MICROLOOP ENCLOSURE SPECIFICATIONS
GENERAL
Number of Input cable ports 2 x Input cable or a mid-span loop.
Cable diameters 2.0 - 6.0mm
Number of output cable ports 4
Cable Diameters 2.0 – 6.0mm
Number of adapters 4 off SC SX Flangeless
4 off LC DX Flangeless
Number of heat shrink splices 10 off 2.4 x 45mm heat shrink splice protectors double stacked.
Splitter Capacity 1 off PLC Bare Fibre splitter 1:2 – 1:8
Or
1 off PLC 900µ splitter 1:2 – 1:8
Bare fibre loop capacity Approximately 70 meters of 250µm bare fibre.
Required space 200 x 115 x 46mm (H x W x D)
Operating Temperature -20°C to +60°C
IP Rating 68
Security Optional barrel lock
Material
Outer casing PPGF
Internal assembly ASA
Splice Tray ABS
Seal Silicone
ML001 November 2018 Page 3 of 7
FTTX MICROLOOP ENCLOSURE SPECIFICATIONS
Main Body Top View Main Body Rear View
Main Body Front View
ML001 November 2018 Page 4 of 7
FTTX MICROLOOP ENCLOSURE COMPONENTS
Standard components: o 1 x FTTx MicroLoop Main Body
Including 4 quick release toggle clamps
o 1 x Internal cable assembly with seal
o 1x Bare Fibre Plate (Removable)o 1x Adaptor Plate (Removable)o 1 x Splice Trayo 2x Splice bays
Additional items: o Barrel Locko Customer Brandingo Fibre labelo Cable entry sizes: 2-4mm or 4-6mmo Flangeless Adapters SC/LCo Pigtails SC/LCo Splice Protectors HS 2.4 x 45mmo PLC Splitters 250µ - 900µo Wall mount anchor kit
Main Body with toggle clamps
Adapter plate for pre-connectorized drop cable
Splice tray with splice bay options for PLC Splitter type
Bare fibre mid-span loop storage
ML001 November 2018 Page 5 of 7
900µ Splitter splice bay
250µ Splitter splice bay
Aramid yarn tethering cones
FTTX MICROLOOP ENCLOSURE COMPONENTS
Removable adaptor plate
Removable bare fibre management plate
Cable tie fixation points
ML001 November 2018 Page 6 of 7
Gel seal
FTTX MICROLOOP ENCLOSURE SPECIFICATIONS
Additional Components
Bare Fibre Management Plate
Adapter Plate
ML001 November 2018 Page 7 of 7