Ftc1 install, lift truck access control

Installation & Programming Guide

FTC1 Programable Key Pad Access Control

Version:FTC1-V.1

Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville Ontario, Canada 0A7 www.ivdtsolutions.com

http://www.ivdtsolutions.com


General Specifications 500 different entry code combinations | Aluminum cast housing with

stainless steel finish | Weather proof | Vandal resistant 12 to 80 volt capability | dual relays for multiple device operation | Multiple secu-rity modes and security user levels Built in heater for cold weather use

| Secure push button terminal | IP 65 rated

Technical Specifications Power Supply: 12-80V Power Absorbed: 75mA in standby Illuminated: 115mA Heating: 12V DC:615 mA 24V DC:465 mA Electric Lock Relay Capacity: 2A Auxiliary Relay Capacity 2A Input REX (Opening Button) N.C.(monitor),N.O. (Input) Operating Temperature: da -20 to 55 celcius Protection Rating IP 65 Dimension & Weight: 120 x 76 x 21mm (410g)




Keypad Wiring Connection Drawing: Version 2.832Basic 2 Core Wiring

This wiring diagram is for GAS/IC machine using start solenoid circuit. The Key-pad will time out up to a maximum of 99 seconds see next section, immobiliza-tion system.


Solenoid Starter Circuit No Relay Contacts

+ Relay Coil Grey Wire on Keypad

- Relay Coil Connect to Both Black on Key-

+ Ignition + Connect to Red & Purple on Key-

- Ignition - Connect to BOTH BLACK on Key-



Additional Instructions for Programming FTC1 Keypad: Immobilization System

To Enter Programming Mode:

1. Power up vehicle (green “MODE” light on keypad is on)2. Press ## twice (keypad light turns red “MODE” light is off)3. Enter master code (1234) vehicle light turns green the units are pre-

programmed with this number

To Change Master Code:

1. Enter programming mode2. Press 3 (“MODE” light turns green)3. Enter new 4 digit master code at this point4. Keypad will return to normal

FOR DEALER FITTING KEYPAD ONLYTHIS MUST BE DONE FIRST WHEN PROGRAMMING




Additional Instructions for Adjustment of Time Delay for FTC1 Pro-gramable Keypad Access Control


1. Power up vehicle (green “MODE” light on keypad is on)2. Press ## twice (keypad light turns red “MODE” light is off)3. Enter master code (1974) vehicle light turns green4. Press 6 to enter menu 6 (the “MODE” LED will flash green)5. Press 00 to energize relay6. Press desired time delay 1 - 99

For example, in steps 6 and 7 (0015 would mean 15 second delay)




END USER INSTRUCTIONSInstructions for Programming FTC1 Programmable Keypad Access Control


1. Power up vehicle (green “MODE” light on keypad is on)2. Press ## twice (keypad light turns red “MODE” light is off)3. Enter master code (1974) vehicle light turns green

To Assign User Codes:

1. Enter programming mode2. Press 7 on the keypad (vehicle light turns Orange)3. Press 001 to assign code slot (mode light flashes green)4. Enter 4 digit user code (ie. 1515 mode light stops flashing - this assigns

1515 to user slot 001)5. Press # once to go straight to next user slot (ie. 002)6. Repeat 3,4 & 5 until all required slots are filled7. Press ## twice to exit programming mode




To Delete User Codes:

1. Enter programming mode2. Press 8 on the keypad (vehicle light turns Red)3. Enter user slot ID (ie. 001 mode light will flash Red)4. Enter programming master code to confirm5. Keypad will return to normal mode

Important Note: Please keep an updated spreadsheet with driver codes and al-located slot numbers!




Ftc1 install, lift truck access control

Technology

Transcript of Ftc1 install, lift truck access control