front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories...

38

Transcript of front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories...

Page 1: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder
Page 2: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

front ends & fork legs

14-2

ness-tech® 41mm lower fork legsDesigned for Wide Glide® front ends ‘84-up. Kit includes lower legs and axle only. Legs are designed to use factory internal components which can be purchased separately.See page 14-3 for some of the components.Dual Disc chromef2856 Smooth f2857 Grooved

41mm custom fork kits & chrome lower leg setsWorks for 41mm forks, 1984-99. The lower legs are machined from billet aluminum and feature screw on dust covers, flush mount axle with hidden hardware and removable brake and fender mounts. The fork tubes are hard chrome plated to provide years of dependable service. The removable brake mounts are designed for ‘84-99 OE or similar brake calipers and 11 ½“ O.D. brake discs. Fits FXST ‘84-99, FXWG ‘85-86, FXDWG ‘93-99. See page 14-32 through 14-34 for all available triple trees and see page 14-3 for internal fork components.

stock 2” over 2” unDer

lower fork legs only

f2835 f2837 f2839 f2833 single Diskf2836 f2838 f2840 f2834 Dual Disk

chrome Billet massive 70mm clamP lock front enDPantented clamp lock design to secure the triple tree with fork tubes. Smooth and clean top triple tree without any visible hardware. Massive fork tube covers. Hidden fork stop. Assembly required. Fits: FXST 84-99, FXWG 85-86, FXDWG 93-99. Single or dual disc.f2841 31” From Top Bearing To Axle

sPyke inverteD front enDsChrome triple tree clamps machined from billet 6061-T6aluminum. 63.5mm diameter chrome upper tubes. Chrome billet “Smooth look” legs. 45mm hard chrome slider tubes. Speed sensitive damping for a plush ride with uncompromising road holding ability. Set up for single or dual disk. Progressive rate springs control ride over a wide variety of surfaces. Available from 2” under to 24” over.f2830 Inverted Wide Glide Front end 32” Chromef2831 Inverted Wide Glide Front end 34” +2 Chrome*Note: Any size available by special order. Ask your sales rep for details.

Page 3: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-3

front ends & accessories custom sPringer® front enD

These great custom made Springers from Rolling Thunder are reminiscent of the glory days of American motorcycles. The rockers feature nylatron bushings and hardened steel inserts. This system, developed by the aerospace industry provides a much longer life without the hassle of lubrication. The bolts on the trees, rockers and axle are made from heat-treated stainless steel and are flush mount. It is also set up for single or dual brakes and has built in fork stops designed especially for Rolling Thunder frames. It’s fully CNC machined, tig welded and triple chrome plated. There has never been so much detail put into a Springer® until now.

f2861 Custom Springer® 4” Over f2862 Custom Springer® 5” Over f2863 Custom Springer® 6” Over f2864 Custom Springer® 7” Over f2865 Custom Springer® 8” Over f2866 Custom Springer® 9” Overf2867 Custom Springer® 10” Overwe can sPecial orDer any siZe sPringer® over 10”ask your salesperson for the details

Rolling Thunder’s custom handlebars are constructed with 1 ½” steel tubing. Kit includes the handlebars, billet aluminum grips and spacers and are triple chrome plated. The bars and the stainless bottom bolts have been drilled through for wiring. This kit also includes an internal throttle assembly. Rise: 8” Pullback: 7 ½” Width: 31”h4201 Custom Handlebar Kit h4202 Replacement Billet Aluminum Grips Chromeh4203 Replacement Internal Throttle Assembly

fork tuBe rePlacement Partsa. f2113 Springs repl. oem 46048-84B. f2124 Small spring repl. oem 45855-77c. f2125 Fork boot repl. oem 45420-80D. f2129 Oil seal retaining clip repl. oem 45842-77e. f3914 Lower stop repl. oem 45834-77f. f2130 Bushing, upper; fits in lower legs 41mm repl. oem 45940-84g. f2137 Bushing, lower; fits in fork tube 41mm repl. oem 45866-84h. f2106 Damper tube repl. oem 45418-84

IMPORTANT: • Please Specify for single or dual disc brake. • Please Specify with or without OEM type Fender mounts. • This Springer® is designed for 35˚ rakes and above.• The Springer® is the same width as stock OEM.

custom hanDleBar kitgauges anD controls shown not incluDeD See page 7-19 for gauges

a.

B.D.

e.

f.

g.

h.

c.

Page 4: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

fork tubes, dampeners & seals

14-4

f2107 ‘86-99 FLSTf2106 ‘84-up FXWG/FXST f2103 ‘77-84 FL/FLH f2104 ‘80-83 FXWG f2105 ‘75-83 XL/FX f6178 XL, FXR & FLT Damper tube mount screws 10 pack

chrome fork tuBesQuality is the main word used when talking about our Fork Tubes. Made from the finest steel available and centerless ground to a perfect fit. Spacers are provided where needed.

fork DamPer tuBe assemBlyThese complete damper tube assemblies duplicate the original specifications.

DamPer valve kitThis fork damper valve kit includes the complete oil shock damper valve assembly for ‘49-77. Sold eachf3230 Wide Glide® damper valve complete assembly repl. oem 46161-49

fork seals

s4011 39mm ‘87-up fXD, fXr, Xl repl. oem 45378-87

s4012 41mm ‘84-up fXst, flst, fXDwg, flh, flht repl. oem 45875-84a

s4013 35mm ‘84-87 fXD, fXr, Xlrepl. oem 45387-83

s4030 41mm ‘77-84 flh, flht, fXwgrepl. oem 45843-77

s4010 35mm ‘75-83 fX, fXr, Xlrepl. oem 45400-75

s4020 41mm ‘48-e77 flh repl. oem 45852-48

-2” stock +2” +4” +6” +8” fork tuBe aPPlication rePl. oem#

stock length

wide glide®

f2012 f2013 f2045 ‘86-up flst 45930-86 22 7/8”

f2015 f2014 f2016 f2017 ‘93-up fXDwg, ‘84-up fXst/c, ‘84-86 fXwg 45417-84 24 1/4”

f2011 f2010 f2012 f2013 ‘84-up flt/ht 45827-84 20 7/8”

f2007 f2008 f2009 ‘80-83 fXwg 45417-80 24 1/4”

f2005 f2004 f2006 f2007 l77-84 fl/h/hX, ‘80-83 flt/ht 45825-77a 20 7/8”

f2001 f2000 f2002 f2003 ‘49-e77 fl 45950-48 20 1/2”

narrow glide®

f2040 f2039 f2041 f2042 f2043 f2044 ‘87-94 fXlr, fXr/rs except sport edition 45381-87 23 3/8”

f2041 f2042 f2043 f2044 ‘87-91 fXrs sport edition, ‘88-91 fXrt 45393-87 25 3/8”

f2036 f2037 f2038 ‘87 fXrt/rD with 35mm showa fork 45392-86 25 1/4”

f2035 f2036 f2037 f2038 l86-87 fXr with 35mm showa fork coarse thread

45407-86 23 1/4”

f2030 f2031 f2032 ‘83-6 fXrD/t/P, ‘84-5 fXsB, ‘85-6 fXrs sp. Ed. fine thread

45392-83 25 1/4”

f2029 f2028 f2030 f2031 f2032 f2033 l84-85 fXe/ef, ‘84-86 fXr except fXrt/rD fine thread

45407-83 23 1/4”

f2024 f2023 f2025 f2026 ‘76-83 fX/e/ef 45407-75 23 1/4”

f2025 f2026 ‘77-83 fX/s/B/sB/r/rs 45644-77 25 1/4”

f2022 ‘73-76 fX/e 45977-73 23 1/2”

f2019 f2018 f2020 f2021 ‘71-72 fX 45953-71 22 3/4”

sportster®

f2040 f2039 f2041 f2042 f2043 f2044 ‘88-up Xl 45381-87 23 3/8”

f2035 f2036 f2037 f2038 l86-87 Xl 45407-86 23 1/4”

f2029 f2028 f2030 f2031 f2032 f2033 ‘84-e86 Xl 45407-83 23 1/4”

f2025 f2026 ‘79-82 Xls 45644-77 25 1/4”

f2024 f2023 f2025 f2026 ‘75-83 Xl/ch/cr/X/s 45407-75 23 1/4”

f2022 ‘73-74 Xl 45977-73 23 1/2”

f2019 f2018 f2020 f2021 ‘54-72 Xl/k 45953-68 22 3/4”

repl. oem 45932-86repl. oem 45418-84repl. oem 45831-77repl. oem 45418-80repl. oem 45409-75repl. oem 45405-75a

Page 5: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-5

handlebars

h4341 Chubby™ Chopper T-Bar 8” Rise, 6” End rise, 30.5” Wide.

h4342 Chubby™ Chopper T-Bar 10” Rise, 8” End rise, 30.5” Wide.

chuBBy™ choPPer t-Bars 1¼”Transform a factory narrow, mid or wide glide front end from stocker to chopper!

all wilD 1 chuBBy™ Bars are Pre-DrilleD for internal wiringchuBBy™ Drag Bars with Built in 1¼” risersDesigned for maximum style, comfort and control, in 6”, 8”, and big 10” rise. Welds at risers polished smooth. Show chrome. They are 30.5” wide. No wimpy wrist pinchers here. Keep your bike balanced, Chubby’s are the perfect width and at 1¼” thick will maintain the flow from fork tubes right up through the grips.

h4332 Chubby™ Drag6” Rise, 4” End rise, 30.5” Wide

h4333 Chubby™ Drag8” Rise, 5” End rise, 30.5” Wide

h4334 Chubby™ Drag10” Rise, 6” End rise, 30.5” Wide

h4340Chubby™ Road King®

8.5” End rise, 31” Wide, 14.5” Pullback,

10” Center Width

chuBBy™ aPes 1¼”When it comes to Apes, you got to go Chubby™.They look so much better than any standard 1” bar,it will blow you away. Put your arms and wrists at the optimum position for comfort and control. They not only look great, they feel great, too!

h4328Chubby™ Ape 12.5” End rise,

36.5” Wide, 12” Pullback10” Center Width

h4327Chubby™ Ape 16” End rise,

37” Wide, 12.5” Pullback10” Center Width

h4338Chubby™ Ape Springer

12.5” End rise, 38.5” Wide

12” Center Width

h4330Chubby™ Ape

10” End Rise, 36.5” wide, 11” Pullback,

11.5” Center Width

h4331Chubby™ Ape Springer

9.5” End rise, 36.5” Wide

12” Center Width

h4329Chubby™ Ape8.5” End Rise,

36.5” Wide, 11” Pullback,

11.5” Center Width

Page 6: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebars

14-6

h4343 Chubby™ Ape18” End Rise,

37” Wide, 12.5” Pullback,

10” Center Width

chuBBy™ r.k. ii Bar 1¼”h4337 Chubby™ Road King® II 5.5” End, Rise, 35.5” wide, 14.25” pullback, 12” Center Width Designed for riders of average height and above.

h4321 Chubby™ Road King® 5.5” End, Rise, 32.5” wide, 16” pullback, 12” Center Width Designed for short riders.

h4322 Chubby™ Springer® Dresser 5.5” End Rise, 35” wide, 12” pullback, 12” Center Width h4323 Chubby™ FLST/C & FLSTF 4.5” End, Rise, 34.5” wide, 12.5” pullback, 12” Center Width For maximum comfort and control.

h4324 Chubby™ Knuckle 2” End Rise, 36.5” wide, 8.5” pullback, 10.5” Center Width

h4339 Chubby™ Springer® Knuckle 2” End Rise, 36.5” wide, 8.5” pullback, 10.5” Center Width

all wilD 1 chuBBy™ Bars are Pre-DrilleD for internal wiring

chuBBy™ Dragster Bars1 ¼” thick X 30.5” wide, with just the right amount of pullback for optimum comfort and control. Chubby Dragster Bars™ work with stock style risers

h4326 Chubby™ Springer® Dragster 30.5 Wide 6” Pullback,

30.5 Wide, 8.5” Center Width

h4325 Chubby™ Dragster 6” Pullback, 30.5 Wide,

8.5” Center Width

h4337

h4321

h4322

h4323

h4324

h4339

ness-tech® 1 ¼ flyBarsCurvaceous styling. Looks great on any application. Indented models feature internal wiring holes and guides. Available in two heights h4211 Fly Hi bars with indents Width: 30 ½, Rise 9 ½, Pullback 8 ½h4212 Fly Lo bars with indents Width: 30 ½, Rise 7 ½, Pullback 8

h4344 Chubby™ Ape20” End Rise,

37” Wide, 12.5” Pullback,

10” Center Width

chuBBy™ aPes 1¼”Designed for tall riders

v-Drag BarsAvailable new design from Arlen Ness featuring unique V Styling. Now available in 1” and 1 ¼” diameter for that stylish Fat Look. Work great on FXST, FXR and Dyna Glide® models.h4213 1 ¼” V-Drag Bars with internal wiring guide holesh4214 1” V-Drag Bars with indents, internal wiring

Page 7: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-7

handlebars & more

custom hanDleBar kitRolling Thunder’s custom handlebars are constructed with 1 ½” steel tubing. Kit includes the handlebars, billet aluminum grips and spacers and are triple chrome plated. The bars and the stainless bottom bolts have been drilled through for wiring. This kit also includes an internal throttle assembly. Rise: 8” Pullback: 7 ½” Width: 31”h4201 Custom Handlebar Kit h4202 Replacement Billet Aluminum Grips Chromeh4203 Replacement Internal Throttle Assembly

Gauges and controls shown not included. See page 7-19 for gauges

soliD hanDleBar mount kitsThese kits replace the OEM rubber style bushings on ‘49-up Harley® models.h3327 ‘72-earlier all models with steel press fitting

ruBBer DamPer kitThis replacement kit consists of zinc plated cup washers, rubber bushings and steel spacers. ‘73-up XL, FX, FL & ‘82-up FXR models.h3324 Rubber damper kit, repl. oem’s 56153-73, 56158-73, 56159-73, 56157-85

nylon hanDleBar DamPer kith3325 ‘73-up XL, FX, FL & ‘82-up FXR

ness-tech® Polyurethane hanDleBar DamPener kith3328 Kit includes dampners, inner sleeves and chrome washers.

custom suPer BarsThese 1” diameter American made handlebars are designed for style and comfort. They are polished to perfection and brightly chromed.

Polyurethane hanDleBar DamPersIncludes chrome washers, red polyurethane bushings & sleeves.h3329 Heavy duty dampers

‘82-uP with DimPle hanDleBar tyPe wiDth rise Pull

BackcenterwiDth

h4210 2. 1” Dia. Pre-’77 29 ½ 3 10 ½ 7

chrome Bushingcoversf4795 Covers - pair

Page 8: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar risers

14-8

chrome PullBack risersLarge diameter risers give a heavy duty lookto the front end. Looks take a cue from the Harley® Deuce®

r3049 Pullback risers repl. oem 56033-00

chrome wiDe gliDe® style risersChrome plated die cast straight elliptical stem risers. Fits ‘80-86 FXWG. Sold in Pairsr3150 4 ½” repl. oem 56063-82ar3048 6”

wilD 1 chuBBy™ risersThe ultimate enhancement to your front end. Precision machined from billet aluminum with a brilliant chrome finish. Super versatile. They work with all standard 1” bars, Wild 1 Chubby’s™, & most other bars and all top clamps.1 ¼” thick Sold in Pairs.r3051 1 ½” high riserr3054 3 ½” high riserr3052 4 ½” high riserr3053 5 ½” pullbackr3055 6.0” high riserr3056 9 ½” pullback

chrome custom rounD toP risersThese riser top cups bolt from the bottom for a smooth look. Mount with ½” - 20 bolt. Sold in Pairsr3120 4” round top r3130 6” round topr3047 8” round top

chrome shorty risersChrome plated die-cast shorty risers with elliptical stem. 2” shorty. Sold in Pairsr3300 ‘74-83 XL, FX, FXR WITH 35mm forks repl. oem’s 56116-77 & 56117-77

chrome PullBack risersChrome plated die-cast pullback risers with elliptical stem. Fits ‘77-81 FXS, FXD & ‘84-up FXST, FXSTC. Sold in Pairs r3110 4 ½” pullback risers repl. oem 56066-82a

Page 9: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar risers & hardware

14-9

gliDe style risers from PaughcoPaughco’s glide risers are solid steel. For use on 1” or 7/8” handlebars. Can be used on both Wide Glide® and Springer® front ends. Chrome Sold in Pairsr3251 3” rise r3252 5” rise r3253 7” riser3400 4” rise r3401 6” rise r3402 8” rise

Bullet style riser Bolt & washer kitGet custom show quality looks with this highly polished stainless steel kit. Made in America for Dyna Glide®, Wide Glide® and Softail® Custom.f6402 Bullet riser kit

riser Boltsfrom Paughcor3403 Bolts ½ x 20 x 1 ½”r3404 Bolts ½ x 20 x 2”r3405 Studs ½ x 20 x 1 ½”

Post styler3254 3” riser3255 5” riser3256 7” rise

sPringer styler3257 6” riser3258 7” rise

chrome Paughco offset style risersDesigned with a 2” offset and mounted on rubber for maximum comfort. Will fit 1” bars only. Made from top grade machine steel. Springer® style extended 5/8-18” thread for OEM Springer® forks.Sold in Pairs

chrome riser Bolt kitsallen hex sizef6608 f6616 ½ x 13 x 2½f6609 f6617 ½ x 13 x 2¾f6610 f6618 ½ x 13 x 3f6611 f6619 ½ x 13 x 3½f6612 f6620 ½ x 13 x 3¾f6613 f6621 ½ x 20 x 2½f6614 f6622 ½ x 20 x 2¾f6615 f6623 ½ x 20 x 3

chrome riser Boltsfrom garDner-westcottf4195 ½ x 13 x 2¾

Page 10: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar clamps & covers

14-10

hanDleBar clamPThis chrome clamp has an exit hole on the bottom so you can run your wiring inside the handlebars. Fits 1¼” bars with 3.5” riser centers. Chromeh4800 Ball Milled

hanDleBar clamP coversThese chrome die-cast covers handlebar clamp covers hide an eye sore and look great.h3346 Heritage Softail® & Fat Boy® h3332 ‘60-84 FL, FLH models without damper hole, repl. oem 58590-60

hanDleBar clamP PlugsThese chrome plugs fit any socket head screw with ¼” hex. 10 packh3333 Clamp plugs

wilD 1 Billet toP clamPsPrecision machined from billet aluminum. Chrome finish. A perfect complement to Chubby™ risers and bars. Fits 1¼” bars with 3.5” riser centers.h4335 Smooth h4336 Ball Milled

hanDleBar clamP mounting Boltsf4510 ‘84-up with speedo bracketf4520 ‘81-up Big Twin, XLf4530 ‘74-81 Big Twin, XL

uPPer riser hanDleBar clamPsChrome clamps available flat or with a long front skirt. Fits 1¼” bars with 3.5” riser centers.All ‘73-up.r3160 Handlebar clamp, flath3330 Handlebar clamp long skirt

hanDleBar toP clamPsChrome plated die cast without skirt.Fits 1¼” bars with 3.5” riser centers. h3331 Smooth h3344 Ribbed

Page 11: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-11

handlebar controls

stoPlight switch e3823 ‘82-95

e3817

e3815

e3818

e3816 e3819

e3821

e3820

e3822

chrome hanDleBar allen screw sets By garDner westcottSwitch housing & master cylinder screw sets f4105 ‘96-up allen head knurled f4155 ‘96-up allen head smoothf4156 ‘96-up buttonheadf6149 ‘82-95 allen head smoothf4550 ‘82-95 in buttonheadf4540 ‘73-81 allen head smooth

SWITCHES NOT INCLuDED SEE BELOW

SWITCHES NOT INCLuDED SEE BELOW

chrome oem style hanDleBar controls for ‘96-04h3521 Complete kit 11/16” boreh3522 Complete kit 9/16” bore

replacement Partsh3526 Switch housing upper left h3527 Switch housing lower left h3524 Switch housing upper right h3525 Switch housing lower right

h3536 Switch housing, right top repl. oem 71564-82h3537 Switch housing, right bottom repl. 71563-82ah3538 Switch housing, left top repl. oem 71567-82h3539 Switch housing, left bottom repl. oem 71568-82a

chrome oem style hanDleBar controls for ‘82-95h3530 Complete kit 3/4” bore m/cyl dualh3531 Complete kit 5/8” bore m/cyl singleh3532 Complete kit 11/16” bore m/cyl dualh3533 Master cylinder with lever 3/4” bore repl. oem 45013-82h3534 Master cylinder with lever 5/8” bore repl. oem 45019-85ah3535 Master cylinder with lever 11/16” bore repl. oem 45019-85al4120 Lever clamp only, repl. oem 45044-82l4130 Clutch lever clamp assembly w/anti rattle device

repl. oem 71567-96repl. oem 71568-96repl. oem 71564-96repl. oem 71563-96

82-95 rePlacement hanDleBar switches for Big twin & sPortster®

96-uP

chrome Black oem Description oem chrome Black- e3823 71574-82 Handlebar Stoplight Switch 71590-96 - e3833

e3816 e3820 71571-82 Engine Run / Off, Starter 71589-96 e3825 e3829e3815 e3819 71573-82a Hi / Low Dimmer & Horn 71597-96 e3827 e3831e3818 e3822 71591-82a Right Turn Switch 71591-96 e3826 e3830e3817 e3821 71570-82 Left Turn Switch 71598-96 e3828 e3832

‘82-95 PictureD

Page 12: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar controls

14-12

Complete chrome billet aluminum handlebar controls. These kits will accept all the factory switches, buttons, etc. (except brake light) on all ‘82-95 models. Each kit includes a handlebar master cylinder, clutch lever perch, clutch lever, custom clutch cable pin and two switch housings. Single disc applications use 5/8” kit. Dual disk applications use 3/4” kit switches and throttle not included.

h3663 5/8” bore ‘82-95 complete kit h3664 3/4” bore ‘82-95 complete kith3657 5/8” bore master cylinder only for stock switchesh3661 ‘82-95 chrome switch housing only h3905 Clutch perch only for stock switchesl3314 Clutch lever only

• Feature a unique mounting system with no visible hardware• Lever design yields a shorter clutch pull than stock levers• Kits consist of handlebar master cylinder, clutch perch and lever or hydraulic clutch master cylinder, switch housings, switches and buttons.

chrome ness-tech® raDius hanDleBar control kits

chrome ness-tech® ‘82-95 stock style hanDleBar control kits

chrome ness-tech® Petite hanDleBar control kits

5/8 “ Bore with Cable Clutch3/4 “ Bore with Cable Clutch5/8 “ Bore with Hydraulic Clutch

switch styleh3651 h3652h3653

smooth styleh3655 h3656

• Feature small button switches for a super clean look• Ness designed billet controls are CNC machined• Kit includes a handlebar master cylinder, clutch lever perch, clutch lever, two custom switch housings and four button switches.h3911 5/8 “ Bore with Cable Clutchh3912 3/4 “ Bore with Cable Clutch

rePlacement Partsh3903 Clutch lever perch with petite switchesh3900 Ness petite switch clamp

Page 13: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-13

handlebar controls

ness-tech® master cylinDer reBuilD kith3901 5/8” boreh3902 3/4” bore

chrome clutch master cylinDer with lever for switch PanelTop quality billet chrome polished to a mirror finish. Designed for use on hydraulic clutch assemblies. Left side. Switch panel not included. h3559 9/16” boreh3560 5/8” bore

chrome right hanD master cylinDer with lever forswitch PanelThese master cylinders were designed to be used with ‘72-81 switch panels. All features are the same as custom master cylinders at left. Chrome polished to a mirror finish. Right side. Switch panel not included.h3562 3/4” bore

JayBrake master cylinDer reBuilD kitB3669 9/16” Bore Rebuild Kit

h3657 5/8” bore master cylinder only for stock switchesh3662 ‘72-81 chrome switch housing only h3905 Clutch perch only for stock switchesl3314 Clutch lever only

chrome ness-tech® ‘72-81 stock style hanDleBar control kits

chrome ness-tech® ‘96-uP stock style hanDleBar control kits

h3665 5/8” bore ‘96-up complete kith3905 Clutch perch only for stock switchesl3314 Clutch lever only

Page 14: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar controls

14-14

Dalton controls from BDlJim Dalton has done it again for BDL. He has designed what we believe to be by far the most streamlined handlebar controls to take customizing to the ultimate level. The unique design & features make our controls a must for any stock or custom application. BDL manufactures these controls with the utmost care for quality & fit. Available in chrome and polished.

Dalton chrome griPsg2016 Grips

h3647 h3649

h3646h3648

Dalton foot Pegsf2301 Foot pegs

Brake master cylinder and lever 5/8” Borechrome Polished Descriptionh3645 B5308 Without switchesh3646 B5327 With switches

clutch master cylinder and lever 9/16” Borechrome Polished DescriptionB5322 B5311 Without switchesB5325 B5328 With switches

clutch cable Perch and leverchrome Polished Descriptionh3647 B5312 Fits late model cablesh3648 B5329 Fits late model cables

With switches

switch covers & switcheschrome Polished Descriptionh3649 h3654 Throttle sideh3650 h3658 Clutch side

master cyclinDer rePlacement Parts

h3659 Handlebar brake master cylinder rebuild kith3644 Handlebar clutch master cylinder rebuild kit

g5761 Rubber replacement gasket

Page 15: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-15

switch housings

chrome hanDleBar switch Plate By JayBrakeh3564 ‘72-81

chrome hanDleBar Billet switch housings By Paul yaffe originals These billet housings are chrome plated and designed for use with Ness or Jay Brake clamp on style Front Master Cylinders and Clutch Lever Assemblies.h4931 Billet Switch Housings Pair Switches not included

h3620 Vertical repl. oem 71539-73B

h3630 Switch cover repl. oem 33626-72

h3339 Vertical Beveled h3610 Horizontal repl. oem 71539-72

All switch covers fit ‘72-81 FL/FX/XLchrome switch covers

PolisheD ness-tech® customswitch clamPsThis item fits on all Ness, JayBrake or Performance Machine handlebar master cylinders. Two button design can be used for a starter, turn signal, horn or kill switch. Sold each. Polishedh3903 Clutch lever perch with petite switchesh3900 Ness petite switch clamp

Page 16: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

master cylinder covers

14-16

chrome master cylinDer coversCustomize your master cylinder in seconds with these chrome billet reservoir cover. B4309 ‘96-up all models smoothB4310 ‘96-up all models ball milled

millennium hanDleBar reservoir coversReplaces stock cover. Made from chrome plated billet.Fits ‘96-up EVO, Big Twin and XL models. B2021 Smooth Reservoir CoverB2022 Ball Milled Reservoir Cover

legenDs sPeeD Ball Billet cover Beautifully machined from aircraft quality aluminum and finished with Speed Ball milled design. Chrome.B6892 ‘96-up Fits all front B6891 ‘85-95 Fits all front

ness-tech® master cylinDer covers

chrome master cylinDer covers

Stock type master cylinder top cover with sight glass for all model Big Twins

& Sportster® 1996-up.

Must order gasket and sight glass separately.B4307 Top cover only with DOT 5 decal. repl. oem 45004-96 B4305 Gasket for cover with sight glass repl. oem 45005-96B4306 Sight glass only repl. oem 45042-96

Top cover fits ‘99-up Touring & 2000-up Softail® models.B4311 Top cover repl. oem 54149-99

Ball milleD master cylinDer coverCustomize your master cylinder in seconds with this chrome billet reservoir cover. B4302 ‘82-87 XL

flameD aPPlicationB3580 all front ‘85-95 fl, fl rear

l87-95, Xl rear l87-95B3581 front ‘82-e85 Big twin

Page 17: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-17

master cylinder rebuild kitslate moDel master cylinDer reBuilD kits for moDels ‘96-uP

B3220 9/16 bore single front disc. repl. oem 45006-96B3221 11/16 bore dual front disc. repl. oem 45072-96

B3219 ‘84-86 FX, ‘84-99 FXR except FXRT, FXRS-SP & FXRS-CON & ‘84-95 Softail® 5/8” bore. repl. oem’s 45072-87, 45069-84

B3218 ‘82-83 FX, ‘82-84 FL ‘82-83 FXR, ‘82-E85 FLT & ’82-83 XL 3/4” bore repl. oem 45063-82

B3217 ‘87-94 FLT, FXRT, FXRS-SP, ‘87-94 FXR-CON & ‘92-94 Dyna except FXDWG 11/16 bore repl. oem 45006-87a

Page 18: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar wiring harness

14-18

rePlacement Parts for hanDleBar switch housingsh3335 Retaining plate for button switch. 10 pack repl. oem 71533-72h3336 Rubber boot for brake light switch. Each repl. oem 27751-69Ph3337 Wire terminal for brake light switch. 10 pack

e3170 Light switch repl. oem 71840-29t

e3160 Horn or starter button repl. oem 71800-26ta

hanDleBar control switches &wiring harnessh3334 ‘72-81 Big Twins, ‘73-81 XLh3338 40” wiring harnessh3345 48” wiring harnesse3470 Handlebar brake switch. repl. oem 72001-69B 5 Packe3480 Horn, starter, or turn signal switch repl. oem 71484-72ae3490 Run-off rocker switch repl. oem 71547-75ae3500 High-low rocker switch repl. oem 71546-75ae1696 Long button cap for turnsignal switch repl. oem 71535-72, 10 Packe1697 Short button cap for starter and horn switch repl. oem 71534-72 10 Pack

wiring kitsThese American made wiring kits feature a heavy gauge wire 19 stands in lieu of 16. Connectors come straight from the OEM supplier. The shrink tubing is fire retardant and the completed assembly has been DOT tested.e3554 ‘91-94 FXST, FLST Handlebar set, blacke3552 ‘87-90 FXST, FLST Handlebar set, blacke3553 ‘85-90 FXR Handlebar set, black

Page 19: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-19

brake fluid & accessories

clutch caBle anchorPin & BushingsAn anchor pin with two plastic bushings. 10 packl3310 ‘65-81 XL & ‘68-81 Big Twin clutch, ‘65-72 XL, ‘68-71 FL’s & ‘71-72 FX brake. repl. oem’s 45039-68 & 45036-68

hi-temP Brake fluiDOur new brake fluid from Russell is high temperature rated, D.O.T. 5, and sold each.c1034 Brake fluid

lever BushingSlotted with washer & cotter pinl3311 ‘52-64 FL, FX, repl. oem 45033-49

clutch & Brake lever Bushingsl3308 Plastic bushings 10 pack repl. oem 45039-68

anti-rattle cliPl3307 Repl. anti-rattle clip & screw for clutch lever

lever PinPivot pin & clip. 10 packl3312 Lever pin repl. oem 45032-82

Page 20: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

handlebar levers

14-20

wiDe BanD lever setsThese clutch and brake lever sets feature extra wide gripping areas for added comfort and ease of use. Chrome. l3323 ‘96-up set. Pair l4017 ‘82-95 set. Pairl3324 ‘96-up brake lever only. l3321 ‘82-95 brake lever only.l3322 ‘82-up clutch lever only.

leversReplacement clutch or brake lever for ‘82-95 Harley® models. Chrome.l3305 Clutch lever repl. oem 45017-82tl3306 Brake lever repl. oem 45016-82t

chrome Pystol griP levers By Paul yaffe originalsThese clutch and brake levers are designed to fit Ness or JayBrake style billet controls and are also available for stock factory controls. They are very comfortable and have slightly more throw for easier clutch disengagement. Easy to install.l4021 Ness and Jay Brake stylesl4022 ‘82-95 modelsl4023 ‘96-up models

air gliDer leversThese air glider clutch and brake levers come with Anti-Rattle clip and clutch lever pivot bushings. Chrome.l3309 ‘82-95 models Air glider clutch & brake set

riBBeD hanD lever setThis chrome brake and clutch set comes with a super comfortable soft ribbed rubber insert locked into a tongue and groove channel that is cast directly into these levers. Sold pairl4060 ‘65-81 Lever set repl. oem’s 45016-72 & 45024-65a

repl. oem 45075-96repl. oem 45049-92repl. oem 45016-96repl. oem 45016-93repl. oem 45017-93

Page 21: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-21

handlebar levers

early style custom leversl4050 ‘65-81 Big Twin clutch or brake lever. Chrome. Sold each repl. oem 45017-69tl3304 ‘72-81 all models hydraulic brake lever. repl. oem 45016-73t

hyDraulic Brake leverThis aluminum brake lever. Chrome. Sold each.l3303 ‘72-81 FL, ‘73-81FX, XL models. repl. oem 45082-83t

clutch lever Bracket assemBlyComplete clutch lever assembly includes lever, lever bracket, pivot pin & clip, cable anchor pin, and plastic pin bushing set. Available in chrome or polished finished.h3640 Chrome repl. oem 38608-72 & 38608-73h3341 Polished

kÜryakyn trigger lever setsThese are the finest levers on the market today. You see, your forefinger is your strongest finger but other levers won’t let your strongest fingers work. Our levers allow the forefinger to get a real grip, making it much more comfortable and easier to pull the lever. Add to that the dished out backside of the levers, which Barnett invented twenty some years ago, and you’ve got the best set of levers you’ll ever own. Your hands just fall naturally into place.l3327 ‘96-up H-D® models

Page 22: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

throttle assemblies & sleeves

14-22

foam griPs g3525 ‘81-up Dual Cable

throttle clamP assemBly chromeg3519 ‘81-up Dual Cableg3518 ‘73-80 Single Cable

throttlehousing chromeg3521 ‘81-up Dual Cableg3520 ‘73-80 Single Cableg3507 Adjusting screw

throttlesleevesg3523 ‘81-up Dual Cableg3522 ‘73-80 Single Cable

ness-tech® throttle housing chromeh3914 Single Cable

foam griP set & throttle sleeveg3513 ‘81-up Dual Cableg3509 ‘73-80 Single Cable

ness-tech® coneD throttle housing h3200 Single Cable chrome

ruBBer griPs g3524 ‘81-up Dual Cable g2610 ‘74-80 Single Cable

ruBBer griP set & throttle sleeve g3512 ‘81-up Dual Cableg3508 ‘74-80 Single Cable

leather griPsg3526 ‘81-up Dual Cable

leather griP set & throttle sleeve g3510 ‘73-80 Single Cable

Chrome end plugs

Chrome end plugs

throttle housingChrome billet aluminum &precision made in America.g3503 Dual Cable

Page 23: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-23

grips

g2025 Speed Ball

g2021 Twister

g2601 Grooved

g2600 Flamed

g2014 Replacement rubber

g2024 Ball Milled g2026 Banded

chrome Billet griPs from legenDs

ness-tech® chrome griPsEach set comes with roller bearings and works with single or dual throttle assemblies.

JayBrake chrome griPs

kÜryakyn iso®-griPsThese will be most comfortable hand gripsyou’ll ever take hold of. Styled to match the popular ISO®-Pegs, they dampen handlebar vibration while providing a sure, cushioned feel for long haul comfort.g2603 ISO-Grips with chrome accent

g2604 Torpedo

Page 24: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

grips

14-24

g2256 Grooved O-Ring

DiamonDDiamond shaped rubber inserts. Chromeg3557 ‘73-up all models

wiDe BanD aluminumPopular aluminum grips featuring wide o-rings to soften vibration while still maintaining the high tech show bike look.g3556 ‘73-up all models, Chrome

foamComfort and style with perfectly sized rubber sleeves covered in soft neoprene for minimum vibration.g2650 ‘73-up 1” foam style repl. 56006-82

Big v cruiser By galinDo DesignsWith a leather texture that will never crack or fade and can be washed with soap and water to look like new. Available in black or white.g2682 ‘73-80, blackg2683 ‘73-80, white

Black leather These grips feature genuine black leather which covers a soft foam sleeve. Fits all 1” handlebars. Chrome ends.g2670 ‘73-up black leather grips

Page 25: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-25

grips & accessories

v-twin foam griPsFeaturing the vibration damping feel of foam, these grips take comfort one step further by utilizing handlebars with or without air reservoirs.g3553 ‘73-up without valve stem g3555 ‘73-up with valve stem

eagle sPirit foam griPs Pairg3511 Dual cable sleeve

rePlacement griPenD PlugsThese 15/16” handle grip end plugs are chrome plated.g3515 End plugs repl. oem 56238-62

griPlock By threeBonDA high strength adhesive specially formulated to keep grips in place without damaging the rubber. Griplock puts an end to twisting or sliding grips. c1468 Griplock

Jack hammer griPs PairBlack rubber heavy duty grips.g2640 1” handlebar

stock style griPs PairSmooth original style rubber grips fitting all 1” handlebarg3500 With chrome end plugsg3501 Without end plugs

unassemBleDassemBleD

internal throttle assemBlyGet rid of that ugly throttle cable with this custom internal throttle assembly. Just cut off about four inches of your handlebar and hook it up! Available in both 1” and 1 1/8” grip diameters. Made from quality steel material. Intended for custom application only. h4203 1” Internal throttle

rail style griPsDie cast chrome plated grips with slotted rubber inserts.g2018 Rail style gripsg2017 Barrel style grips

Page 26: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

mirrors

14-26

ness-tech® chrome mirrorsThese mirrors are machined from 6061-T6 billet aluminum. The workmanship and

durability are far superior to other mirrors on the market. Two styles of stems to choose from. All mirrors are supplied with mounting hardware. All of these mirrors are sold each.

m3159 Cateye Grooved with stealth stem

m3141 Oval Louvered with stealth stem

m3142 Cateye Louvered with radial stemm3143 Cateye Louvered with stealth stem

m3144 Round Louvered with radial stemm3145 Round Louvered with stealth stem

Page 27: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-27

mirrors

chrome Billet mirrors This line of billet aluminum mirrors sets a new standard for excellence in function and design. All feature exclusive stainless steel pivot that rides in a unique nylon bushing. This means they will never lose adjustment or rust at the pivot. You won’t find any unsightly adjustment screws on the back either. They fit all H-D® clutch and brake housings from ‘72-up. All necessary hardware included. Sold each.

m3135 Weekend Warrior, oval head Cut out, leftm3136 Weekend Warrior, oval head Cut out, right

m4202 Tear Drop, ball milled leftm4203 Tear Drop, ball milled right

m4201 Pro Street, oval head right

m4206 Round teardrop left m4207 Round teardrop right

kÜryakyn magnum mirrorsWe call them Magnum because of their rugged design. Every component has been beefed up. unlike other flimsy mirrors, ours feature sturdy stems and an oversized adjuster ball that hold its position under the toughest conditions. Available in two head sizes: same square-inch head size as stock; or 20% smaller that stock. Magnum mirrors will replace most stock H-D® mirrors. Not recommended for Buckhorn style bars. Stems and Heads available in chrome only.m3152 Small head, standard stem.m3153 Large head, standard stem.

m3152 m3153 m3154 & m3155

kÜryakyn elliPse mirrorsThese state of the art custom mirrors are cut from the same mold as our turn signals mirrors but, they do not have the running light and turn signal functions. They are available with your choice of flat or convex glass and feature an oversized swivel ball for superior locking ability.m3154 Flat glass.m3155 Convex glass.

5” 5”

2 5/8” 3”

Page 28: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

mirrors

14-28

JayBrake ultra mirrorsThis beautiful piece of work is truly one-of-a-kind. The unusual shaped mirror measures 4 ½” long, 2” wide and is tapered to 1”. Its height is 7” to 7 ½”. The ultra mounts on H-D® clutch lever housings and most common mounting applications. Chromem3013 ultra left

m3015 Dual ultra slotted m3016 Single ultra slotted

custom mirror mountThese are really nice for those Builders who want the ultimate clean look.Polished stainless steel m3120 Mirror mount

ness-tech® cateye softBenD Die cast mirrorsFree flowing styling. Quality diecast construction. Fits right or left side of handlebars. Chrome plated.Hardware for Harley® and Cruisier modelsincluded.m3156 Groovedm3157 Smooth

m3156

m3157

Page 29: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-29

mirrors

chrome rectangular tinteD mirrorsMeasuring 2” x 4 ¼”, these custom mirrors have a tinted glass and die cast housing attached to a 6” one piece stem. Pairm3129 Mirrors with diamond stem

chrome semi-DiamonD mirrorsThis hot new semi-diamond style features a stealth stem with beautiful chrome pair.m3130 ‘73-up

chrome Die cast rePlacement mirrorsThis is a heavy duty die cast mirror just like the original. Each mirror fits in stock clutch or brake lever housing. It features lightly tinted glass. Sold each.m3010 Die cast mirror with standard stemm3100 Die cast mirror with long stem

m3109 Left short stem m3110 Right short stem

chrome Die cast one Piece mirror

m3111 Left long stem m3112 Right long stem

Die cast one piece mirror just likethe original, has a lightly tinted glass and

is available in left &right with short or long stem.

repl. oem 91894-82trepl. oem 91879-82t

repl. oem 91892-82trepl. oem 91875-82t

Page 30: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

front end accessories

14-30

fork BootsKeeps dust and dirt out of fork seal. Sold in pairs.f2115 ‘49-77 FL, FLH fork bootsf2116 ‘73-74 FX, XL fork boots kayabaf2117 ‘75-87 FX, XL & FXR fork boots showa repl. oem 45404-75t

chrome fork Boot coversf2237 ‘80-86 FXWG, ‘84-up FXSTCf3250 ‘49-E77 Wide Glide® fork cover f2114 ‘76-E87 FX/XL & FXR for 35mm showa forkf3240 FXE, XL front fork covers 35mm

41mm Billet fork leg Dust BootsReplace the stock rubber fork boot with these beautiful cover billet dust covers. Sold pair.f2822 Ball Milled Dust Cover Chrome

fork sliDer Bottom caP stuD & nut kitChrome plated locknuts and replacement studs.f6354 ‘49-77 FLH Wide Glide® f6355 ‘73-up Showa & Kayaba

chrome fork sliDer coversThese chrome fork slider covers fit ‘49-88 FL.Available in stock or 2” over stock. Sold in pairs.f2118 Stock repl. oem 45964-49f2119 2” over stock

Page 31: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-31

fork & mirror products

chrome 2 Piece mirror clamPFits 1” handlebars and can also be used to mount turn signals and other accessories using a 5/16” bolt. Sold eachm3069 1” handlebars

chrome rePlacement mirror stemsm3115 Standard mirror stem 4” long overall eachm3116 Long mirror stem 8” long overall each

fork oilFork Tuner fork oil features consistent, smooth damping action for all seasons. This non-fading, non-foaming formula allows you to fine tune your ride to personal preference and contains a preservative to prevent seal leaks.

fork allen screw setsBy garDner westcottFork leg drain f4470 ‘77-up FLH Front & FXWG, FXST, FLT with special washerf4450 ‘73-up Front FX, FXR, FXLR with special washer f4460 ‘47-77 FLH & 45” Front

16 oz. sold each 6/case weightc1032 c1029 sae 10wc1033 c1031 sae 15wc1018 c1030 sae 20wc1019 c1040 sae 30w

Page 32: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

triple trees

14-32

chrome Dust shielDChrome upper and lower triple tree bearing dust shields.f2109 ‘77-up FL, FX upper large repl. oem 48361-80f2110 ‘49-up FL, FX lower small repl. oem 43865-48a

41mm fat trees with turn signalsf2066 Smoothf2065 Ball milled without turn signals

chrome lower triPle tree coverLower triple tree coverf2100 ‘80-85 FXWG & ‘84-85 FXST. repl. oem 67773-80

Page 33: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-33

triple trees

chrome 41mm Billet triPle trees

f2078 Wave Triple Tree Set

f2081 Curved Stepped Triple Tree Set

f2080 Curved Radius Triple Tree Set

f2079 Edged Triple Tree Set

chrome 41mm Billet triPle treesMade from 6061-T6 premium billet aluminum, these CNC precision made triple trees feature internal brake junctions for that cleaner custom look. Our F2084 0˚ Rake triple trees also have internal brake junctions & that is a big difference between these fine trees & others on the market. Please see our hidden internal fork stop kit F2829 on page 14-35 which is also available for these great uSA Made products.f2084 0˚ Rakef2082 3˚ Rake f2083 6˚ Rake

Turn Signal Mount

chrome 41mm BillettriPle treesgroovedf2440 Without turn signal mount f2442 With turn signal mountsmooth with 3˚ rakef2441 Without turn signal mountf2443 With turn signal mount

3˚ Rake

Page 34: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

triple trees

14-34

ness-tech® 39mm wiDe gliDe® conversion kitThis custom tree set will convert your existing ‘99 - earlier Narrow Glide® into a Wide Glide® 9.875” width front end. Kit includes polished billet aluminum trees, steering stem, top nut, axle, axle spacers, fender spacers, headlight mount and one disc spacer. For models with dual disc applications order an extra spacer. Top trees includes a window for easy routing of cables and wires. They also accept handlebar dampeners to eliminate vibration. Bottom trees feature built in fork stops; Ness fork stems are machined to accept the factory fork lock.f3860 Wide Glide® conversion kitf3861 Disc spacer for dual disc

ness-tech® 41mm raDiuswiDe gliDe® triPle treesKits consist of top and bottom aluminum trees, steering stem and allen top bolt, headlight mount & all necessary hardware. Fits Wide Glide® front ends ‘49-upf3855 Radius smooth, chrome.f3856 Radius stepped, chrome.f3857 Fork stop kit for FXST, and 4 speed Big Twin

ness-tech® triPle treesThese state-of-the-art triple trees are machined to exact tolerances from solid billet 6061-T6 aluminum alloy. They are light and feature the convenience and comfort of stock triple trees such as tapered top tree to accept stock forks and the use of stock top nut and rubber handlebar dampeners. Each set comes with top and bottom trees, steering stem, chrome pinch bolts and set screw.f3811 ‘49-up Wide Glide® 41mm Chromef3857 Fork stop kit for FXST, & 4 speed Big Twin

stealth chrome triPle treesFork stop headlight mount included. Stem & stainless steel hardware included.f2503 41mm Wide Glide® f3851 41mm Dyna Wide Glide®

Page 35: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-35

fork cups, bearings & races

fork cuP kit By PaughcoKit comes complete with fork cups, bearings and dust shields.f2403 Head cup kit

fork Bearings anD racesB3924 ‘78-81 XL Timken Head Cup Bearing repl. oem 45586-78B3918 ‘60-up Big Twin & 82-up XL Front Neck Bearing with Race repl. oem 48300-60B3922 ‘49-up FL, FXWG, Softail® Tapered Timken Head Cup Bearing, No Race repl. oem 48300-60B3919 ‘60-up Big Twin & ‘79-up XL Fork Bearing Race only repl. oem 48315-60B3923 ‘49-up FL, FXWG, Softail® Timken Head Cup Race repl. oem 48315-60

custom fork Bearing cuP kitConverts Sportster® models from ball bearings to tapered Timken style bearing. Bearing included.f2108 Tapered bearing conversion kit for Sportster® 1977 & earlier.

internal fork stoP kit These hidden fork stop kits are very high quality & the best on the market. Cups are highly polished stainless steel. F2829 kit includes bearings & races & both kits contain stainless steel internal parts. Keep your forks from banging’ into that expensive painted gas tank.f2829 FXST Custom Internal fork stop kitf2821 FXST Custom Internal fork stop kit without bearing & races

chrome Billet fork lock cover for roaD king®

Protect your forks from the outside elements with this fork lock cover. Simple to install. f2828 ‘94-up Road King®

repl. oem 1659-99

f2829

Page 36: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

fork tube caps & bolts

14-36

PlateD fork stem BoltChrome dome shape with chrome washer bolt and cover. f4044 ‘86-up FLST, FXR, FXD and XL. repl. oem 4453

chrome PlateD fork stem caPChrome fork stem cap with 1/4-20 stud screws. use with Win F4048. f4046 ‘86-up FLST, FXR, FXD and XL. repl. oem 9976-2

chrome PlateD fork stem caPChrome fork stem cap with 1/4-20 stud. f4047 ‘80-up FXST and FXWG. repl. oem 45670-80

fork tuBe caPThis chrome fork tube cap replaces the original equipment. A classic look for Super Glide® and Sportster® models. American made.f6353 L85-up XL & Super Glide®

f6352 ‘73-E85 XL & Super Glide®

f6356 XL & K ‘52-72, Super Glide® ‘71-72f4451 Fork Top Bolt 39mm Hex Cap

fork tuBe BoltsChrome replacement fork tube bolts for Wide Glide® front ends.f6351 ‘78-up Non-vented Zinc plated, flat top fork tube bolt. A duplicate of original equipment used on glide forks ‘60-67.f6350 ‘49-77 Ventedf6348 Fork tube bolt repl. oem 45754-60

Page 37: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

14-37

fork tube washers & stem nuts

fork tuBe Bolt washersChrome fork tube bolt washers are used with fork tube bolt.f4043 ‘78-up FL, FXWG & Softail® repl. oem 5710

fork tuBe BoltChrome duplicate of original equipment. Includes washer.f6360 ‘78-up FL, FXWG, Softail® repl. oem 45419-80

stem Bolt & washer kitZinc plated bolt, complete with washer. use with Win F4046, chrome cap. f4048 ‘86-up FLST, FXR, FXD and XL repl. oem 4453

chrome PlateD stem nutFits FX, FL, XL ‘71-up & ‘79-up with stock triple tree clamp as well as the years below.f6347 ‘80-up FXWG & ‘84-up FXST f6346 ‘57-78 XL

fork tuBe PlugsChrome plug screws into fork tube. American made.f6357 ‘48-77 Wide Glide®

f6358 ‘78-up Wide Glide®

f3260 ‘48-77 Wide Glide® Import repl. oem 45776-49

stem nut & lockwasher kitPrecision machined stock stem nut and stamped steel lockwasher without steering damper.f6349 ‘49-77 Wide Glide®

Page 38: front ends - Welcome to Starwest Inc.starwestinc.com/section14.pdf · 14-3 front ends & accessories custom sPringer® front enD These great custom made Springers from Rolling Thunder

fork tube products

14-38

fork tuBe allen caPs By garDner-westcottEach cap is tapered to the top and is precision machined. Sold pair.f3370 Fits 39mm

chrome fork toP Bolt washerf6176 39mm repl. oem 6655

fork stem uPPer cone seatsThis chrome fork stem cone nuts fits ‘49-84 FL, ‘80-83 FXWG and ‘84-up FXST.repl. oem 48330-48af2111 Nut style adjusterf2112 Tooth style adjuster

fork stem nut for flThis fork stem nut fits with steering dampener.f3222 ‘49-E77 FL repl. oem 45718-48

39mm front enD harDware set f4480 ‘88-up FXR, XL