Franz Wagner & Sohn GmbH Pressure gauge cock · PDF fileNBR 4-5+60°C. Hot water. 7256 ......
1
Pressure gauge cock Design Pressure gauge cocks are intended to isolate Plain valves DIN 16 270 the gauges from the medium in order to enable Valves with test connector DIN 16271 inspection or replacement of the gauge where Valves with test connector and extra shut-off device DIN 16272 the pressure is continually pulsating. These cocks are suitable up to 25 bar and a Valves with test connector enable simultaneous connection temperature span from -20°C to +50°C. of a test gauge to test performance of the pressure gauge in For higher pressure and temperature, valves service. The test connector is normally closed by a sealing cap have to be used. (DIN 16271) or by an extra shut-off device (DIN 16272). Design Conncection Hand wheel Per DIN 16 261 and 16 262. G 1/2 according to DIN 16 288 both sides Thermoset plastic Connection Body G 1/2 according to DIN 16 288 both sides Material Max. pressure PN in bar Body and cone Max. temperature in °C Material: brass Operation, indicated by symbol on top of handle: Needle and seating Corrosion resistant stainless steel Valve per DIN 16 270 LH/RH -union - male thread 1. Isolate and vent pressure gauge into the atmosphere 2. Operate pressure gauge ( standard position ) 3. Isolate pressure gauge and vent pressure system Dimensions and weight into the atmosphere Pressure gauge cock with test connector The test connector enables simultaneous connection of a test gauge to test performance of the gauge in service. Design Per DIN 16 263 Pressure connection G 1/2 according to DIN 16 288 both sides Test connector Male thread M 20 x 1.5 or test flange 60 x 25 x 10 mm or Ø 40 x 5 mm Body and cone Material: brass The handle features a fourth position in addition to the 3 standard positions. In the fourth position both pressure gauge and test gauge are connected to the medium. Pressure rating 25 bar Optional extras Materials: chromed brass; carbon steel; stainless steel AISI 316 Ti; thread other than G 1/2 degreased for oxygen Pressure gauge valve Pressure gauge valves are intended to isolate the gauge from the medium or to provide a means of throttling and damping pressure pulses. 120 Steel AISI 316 Ti 400 400 200 200 Pressure gauge cock and Pressure gauge valve 094 Valve per DIN 16272 LH/RH union - male thread with test connector M 20 x 1.5 and extra shut-off device Valve per DIN 16271 LH/RH union - male thread Brass 250 G ½ Plain valve 0,53 114 50 87 0,55 0,50 Steel 316 Ti Design According to DIN 16 288 Dimensions in [ mm ] Weight in [ kg ] ca. a b c Brass with test connector M 20 x 1.5 test connector M 20 x 1,5 Design Dimensions in [ mm ] Valve per DIN 16 271 with Valve per DIN 16 272 with test connector M 20 x 1,5 and extra shut-off device 114 M 20 x 1,5 90 Weight in [ kg ] ca. a b c Brass Steel 316 Ti 0,67 0,65 0,65 190 M 20 x 1,5 105 0,92 0,92 0,94 MESSGERÄTE FÜR TEMPERATUR DRUCK FEUCHTE Franz Wagner & Sohn GmbH
Transcript of Franz Wagner & Sohn GmbH Pressure gauge cock · PDF fileNBR 4-5+60°C. Hot water. 7256 ......
Pressure gauge cock Design
Pressure gauge cocks are intended to isolate Plain valves DIN 16 270the gauges from the medium in order to enable Valves with test connector DIN 16271inspection or replacement of the gauge where Valves with test connector and extra shut-off device DIN 16272the pressure is continually pulsating.These cocks are suitable up to 25 bar and a Valves with test connector enable simultaneous connectiontemperature span from -20°C to +50°C. of a test gauge to test performance of the pressure gauge inFor higher pressure and temperature, valves service. The test connector is normally closed by a sealing caphave to be used. (DIN 16271) or by an extra shut-off device (DIN 16272).
Design Conncection Hand wheelPer DIN 16 261 and 16 262. G 1/2 according to DIN 16 288 both sides Thermoset plastic
Connection BodyG 1/2 according to DIN 16 288 both sides Material
Max. pressure PN in barBody and cone Max. temperature in °C Material: brassOperation, indicated by symbol on top of handle: Needle and seating
Corrosion resistant stainless steel
Valve per DIN 16 270LH/RH -union - male thread
1. Isolate and vent pressure gauge into the atmosphere2. Operate pressure gauge ( standard position )3. Isolate pressure gauge and vent pressure system Dimensions and weight
into the atmosphere
Pressure gauge cock with test connector
The test connector enables simultaneous connection ofa test gauge to test performance of the gauge in service.
DesignPer DIN 16 263
Pressure connectionG 1/2 according to DIN 16 288 both sides
Test connectorMale thread M 20 x 1.5or test flange 60 x 25 x 10 mm or Ø 40 x 5 mm
Body and coneMaterial: brassThe handle features a fourth position in addition to the 3 standard positions. In the fourth position both pressure gauge and test gauge are connected to the medium.
Pressure rating25 barOptional extrasMaterials: chromed brass; carbon steel;stainless steel AISI 316 Ti; thread other than G 1/2degreased for oxygen
Pressure gauge valvePressure gauge valves are intended to isolate the gauge from the medium or to provide a means ofthrottling and damping pressure pulses.
120
Steel AISI 316 Ti400 400200 200
Pressure gauge cock andPressure gauge valve
094
Valve per DIN 16272LH/RH union - male thread
with test connector M 20 x 1.5and extra shut-off device
Valve per DIN 16271LH/RH union - male thread
Brass250
G ½Plain valve 0,53114 50 87 0,55 0,50Steel 316 Ti
Design According toDIN 16 288
Dimensions in [ mm ] Weight in [ kg ] ca.a b c Brass
with test connector M 20 x 1.5
test connector M 20 x 1,5
DesignDimensions in [ mm ]
Valve per DIN 16 271 with
Valve per DIN 16 272 withtest connector M 20 x 1,5and extra shut-off device
114 M 20x 1,5 90
Weight in [ kg ] ca.a b c Brass Steel 316 Ti
0,67 0,65 0,65
190 M 20x 1,5 105 0,92 0,92 0,94
MESSGERÄTE FÜR TEMPERATUR DRUCK FEUCHTEFranz Wagner & Sohn GmbH
