FORM 160PL INSTRUCTIONS FOR INSTALLATION OF A SAFETY...

FORM 160PL INSTRUCTIONS FOR INSTALLATION OF A SAFETY SWITCH ON THE EE15 / EE20 / EG300 EDGERS

WARNING! Before performing any service to the machine, set themain switch, located on the electric box, in the “0” position anddisconnect the power supply cable.

1. Mounting the 507236 Retrofit Kit for the Edger with production date 06.2009 - 12.2011.

• The 505860 Retrofit Kit is shown below:

FIG. 2

Form 160PL Instructions For Installation of a safety switch on the EE15 / ee20 / eg300 Edgersdoc022112

• Mount the safety switch at the location shown in Figure 3.

FIG. 3

doc022112 Form 160PL Instructions For Installation of a safety

• The safety switch should be mounted so that the safety switch arm is released when the anti-kickback fingers lever is pushed down.

• Route the safety switch wire together with the existing wire harness into the electric box (see Fig. 5, 6 and 7).

FIG. 4

FIG. 5


FIG. 6

FIG. 7


• Locate the terminal block in the electric box. Remove the bypass bridge and connect the safety switch wires to the terminals #12 according to the electric diagram attached.

FIG. 8

Bypass Bridge

Safety Switch Wires


• Make sure that the safety switch is working properly. To do this, start the main motor. Then push the anti-kickback fingers lever (shown below) down to raise the anti-kickback fingers. The main motor

FIG. 9

ST

DWNUP

DP

Dl1 Dl2A B A B

24V

ATVLi1

10V

Ai1

COM

Vcc GND W1 W2

12VAC

~

100776

OBRZYNARKA DWUSTRONNA

Schemat elektryczny

B2

Lasers

~+ -

BlueBrown

Power Supply

D

01/07/2011


should stop. With the anti-kickback fingers raised, try to start the motor using the START button. It should not be possible to start the motor.

FIG. 10


2. Mounting the 507236 Retrofit Kit for the Edger with production date 09.2001 - 06.2009.

• The 505860 Retrofit Kit is shown below:

FIG. 3


• Mount the safety switch at the location shown on Figure 3.

• The safety switch should be mounted so that the safety switch arm is released when the anti-kickback fingers lever is pushed down.

• Route the safety switch cable as shown on the figures 5, 6 and 7).

FIG. 4

FIG. 5


FIG. 6 ROUTE THE CABLE THROUGHT THE MAIN TUBE GROMMET

FIG. 7 INSERT THE SAFETY SWITCH WIRE INTO THE ELECTRIC BOX


• Locate the terminal block in the electric box. Remove the bypass bridge and connect the safety switch wires to the terminals according to the electric diagram attached.

FIG. 8

FIG. 9

Bypass Bridge

Safety Switch Wires

Safety Switch Wires


• Make sure that the safety switch is working properly. To do this, start the main motor. Then push the anti-kickback fingers lever down to raise the anti-kickback fingers. The main motor should stop. With the anti-kickback fingers raised, try to start the motor using the START button. It should not be possible to start the motor.

FIG. 10

1 2

3 4

5 6

1 2

3 4

5 6

1 2

3 4

5 6

1 2

3 4

5 6

M1

1M

2M

3M

23

0/4

00V

, 50

Hz

3~

L1

L2

L3

NP

E

GV

3M

2M

1M

21

22

68

67

3M

TD

R

56

55

2221

2M

0

1314

1M

24

12

L1

F2

24

1

24

0

Q

12

34

3 43 4 3 4

3 4

400

415

3

P1

W1

W2

P2

P3

0

096233

Wo

od

- M

ize

r In

du

str

ies

sp

.z.o

.o.

Ul.N

ag

órn

a 1

14

62

-60

0 K

o³o

, P

ola

nd

Pro

dukt

Data

Ryso

wa

³

KK

Sp

raw

dzi³

Na

zw

aN

um

er

rys.

We

rsja

A

OB

RZ

YN

AR

KA

DW

US

TR

ON

NA

18/0

6/2

004

Schem

at ele

ktr

yczny o

brz

ynark

iw

ers

ja E

25

C1

A

F1

1 3

2 4

C1A

TR

13

14

W3


FORM 160PL INSTRUCTIONS FOR INSTALLATION OF A SAFETY...

Documents

Transcript of FORM 160PL INSTRUCTIONS FOR INSTALLATION OF A SAFETY...