for emample mmmmmmm universal 9AE trunking...
Transcript of for emample mmmmmmm universal 9AE trunking...
804
for e ample for e ample for e ample
805
Red catalogue numbers: New products
universal trunkingbodies, nishing accessories and mounting wiring accessories
TRUNKING TRUNKING AND ACCESSORIES ANGLES FLAT JUNCTION(3) Angled junction
Number of compartments
Covers width (mm)
Size (mm)
Body and covers complete
Separation Clips Base joints(1)
Cover joints
End cap Internal angle(2) 85 to 95°
External angle(2) 60 to 120°
Flat angle To width 80 mm
To width 105 mm
UNIVERSAL DLP TRUNKING - 65 mm COVER
1
6535 x 80 0 104 61 0 105 84 0 106 81 0 106 92 or
0 106 91 0 108 01 0 107 22 0 106 01 0 106 21 0 107 67 0 107 35 - 0 107 63 + 0 106 01
6550 x 80 0 104 62 0 105 82 0 106 81 0 106 92 or
0 106 91 0 108 01 0 107 22 0 106 02 0 106 22 0 107 67 0 107 35 - 0 107 63 + 0 106 02
6550 x 105 0 104 24 0 105 82 0 106 81 0 106 96 0 108 01 0 107 00 0 106 05 0 106 19 0 107 86 0 107 39 0 107 40 0 107 65
+ 0 106 05
2
65 6550 x 150 0 104 27 0 105 82 0 106 81 0 106 92 or
0 106 91 2 x 0 108 01 0 107 03 0 106 06 0 106 35 0 107 89 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 06
3
40 65 4050 x 170 0 104 67 0 105 82 0 106 82 0 106 92 or
0 106 912 x 0 108 00 + 0 108 01 0 107 10 0 106 50 0 106 38 0 107 98 0 107 35 0 107 36 or
0 107 370 107 63
+ 0 106 50
65 65 6550 x 220 0 104 28 0 105 82 0 106 81 0 106 92 or
0 106 91 3 x 0 108 01 0 107 05 0 106 50 0 106 38 0 107 95 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 50
UNIVERSAL DLP TRUNKING - 85 mm COVER
1
8535 x 105 0 104 63 0 105 82 0 106 82 0 106 92 or
0 106 91 0 108 02 0 107 01 0 106 01 0 106 21 0 107 84 0 107 35 0 107 36 0 107 63 + 0 106 01
8550 x 105 0 104 64 0 105 82 0 106 82 0 106 92 or
0 106 91 0 108 02 0 107 02 0 106 02 0 106 22 0 107 85 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 02
2
85 8550 x 195 0 104 70 0 105 82 0 106 82 0 106 92 or
0 106 91 2 x 0 108 02 0 107 11 0 106 06 0 106 35 0 107 92 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 06
UNIVERSAL DLP TRUNKING - 130 mm COVER
1
13050 x 150 0 104 65 0 105 82 0 106 86 0 106 92 or
0 106 91 0 108 04 0 107 03 0 106 02 0 106 22 0 107 89 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 02
13065 x 150 0 104 75 0 105 83 0 106 86 0 106 92 or
0 106 91 0 108 04 0 107 06 0 106 03 0 106 23 0 107 90 0 107 33 0 107 38 0 107 64 + 0 106 03
UNIVERSAL DLP TRUNKING - 180 mm COVER
1
18050 x 195 0 104 69 0 105 82 0 106 86 0 106 92 or
0 106 91 0 108 06 0 107 11 0 106 02 0 106 22 0 107 92 0 107 35 0 107 36 or 0 107 37
0 107 63 + 0 106 02
180
65 x 195 0 104 76 0 105 83 0 106 86 0 106 92 or 0 106 91 0 108 06 0 107 07 0 106 03 0 106 23 0 107 93 0 107 33 0 107 38 0 107 64
+ 0 106 03
1: 0 106 92: base joint for aligning bases, 0 106 91: base joint, attached with adhesive 2: Internal and external angles include partition junction(s) for installation with multi-compartment trunking 3: Flat junctions Cat.Nos 0 107 37 and 0 107 40 are suitable for tap-off to a 105 mm wide profile equipped with a 65 mm cover and flat junctions Cat.No 0 107 36 and 0 107 38 are suitable for tap-off to a 105 mm wide profile equipped with a 85 mm cover
Cover width
65 mm 85 mm
Cat.Nos Cat.Nos
ARTEOR AND MOSAIC SUPPORTS(1)
2 modules 0 109 52 0 109 92
4 modules 0 109 54 0 109 94
6 modules 0 109 56 0 109 96
8 modules 0 109 58 0 109 98
MOSAIC SOCKETS OUTLETS - AUTOMATIC TERMINALS GERMAN STANDARD
Standard Red Tamperproof
2P+E, 2 modules 0 774 01 - 0 774 21
2 x 2P+E, 4 modules 0 774 02 0 774 12 0 774 22
3 x 2P+E, 6 modules 0 774 03 0 774 13 0 774 23
4 x 2P+E, 8 modules 0 774 04 - 0 774 24
MOSAIC SOCKETS OUTLETS - SCREW TERMINALS GERMAN STANDARD
Standard Red Tamperproof
2P+E, 2 modules 0 776 01 - 0 776 21
2 x 2P+E, 4 modules 0 776 02 0 776 12 0 776 22
3 x 2P+E, 6 modules 0 776 03 0 776 13 0 776 23
4 x 2P+E, 8 modules 0 776 04 - 0 776 24
UNIVERSAL SUPPORTS(2) FOR 60 mm FIXING CENTER (Galea, Valena, Suno, Cariva, Niloé)
Cover width
85 mm
1 gang 0 109 13
2 gang 0 109 23
3 gang 0 109 33
1: Supplied with finishing plate2: Supplied with the socket and its support and finishing plate
universal trunkingmounting of wiring accessories
Whitelength m
806
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition24 0 104 611 Supplied with:
- one 35 x 80 mm body- one fl exible 65 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition16 0 105 841 Self-adhesive separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)10 0 108 01 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 01 Changeable internal bend, from 85° to 95°for 35 x 80 and 35 x 105 mm trunking
10 0 106 21 Changeable external bend, from 60° to 120°for 35 x 80 and 35 x 105 mm trunking
Flat angle10 0 107 67 90° fl at angle
End cap10 0 107 22 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm
wide profi le
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 01
Accessories50 0 106 81 Clip
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
Wiring accessories supports and installation accessories (p. 819 to 821)
Flat junctionCat.No 0 107 35Changeable
internal angleCat.No 0 106 01
Changeablefl at angle
Cat.No 0 107 67
Changeable external angle
Cat.No 0 106 21
Cat.Nos for x trunking
Whitelength: m
ArteorMosaic
Compatible ranges
Selection chart p. 804-805Wiring capacity chart p. 803
1: Number of metres in pack
80
65
35
807
for example xxxxxxxxxxxxxxx
Wiring accessories supports and installation accessories (p. 819 to 821)
Selection chart p. 804-805Wiring capacity chart p. 823
Pack Cat.Nos Universal trunking
Trunking without partition20 0 104 621 Supplied with:
- one 50 x 80 mm body- one fl exible 65 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)10 0 108 01 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 02 Changeable internal bend, from 85° to 95°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
10 0 106 22 Changeable external bend, from 60° to 120°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
Flat angle10 0 107 67 90° fl at angle
End cap10 0 107 22 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm
wide profi le
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 02
Accessories50 0 106 81 Clip
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
80
65
50
Flat junctionCat.No 0 107 35Changeable
internal angleCat.No 0 106 02
Changeablefl at angle
Cat.No 0 107 67
Changeable external angle
Cat.No 0 106 22
Cat.Nos for x trunking
Whitelength: m
ArteorMosaic
Compatible ranges
1: Number of metres in pack
808
for example xxxxxxxxxxxxxxx
Pack Cat.Nos Junctions
Flat junction5 0 107 39 For tap-off to a 80 mm
wide profi le
5 0 107 40 For tap-off to a 150 mmwide profi le
Angled junction
5 0 107 65 For tap-off in an internal angle to 35 x 80,35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 02
Accessories50 0 106 81 Clip
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
Whitelength: m
Changeable internal angle
Cat.No 0 106 05
Changeablefl at angle
Cat.No 0 107 86
Changeable external angle
Cat.No 0 106 19
Cat.Nos for x trunking
Flat junctionCat.No 0 107 40
ArteorMosaic
Compatible ranges
Pack Cat.Nos Universal trunking
Trunking without partition12 0 104 241 Supplied with:
- one 50 x 105 mm body- one fl exible 65 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 96 Body joint
For aligning bases during installation
10 0 108 01 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 05 Changeable internal bend, from 85° to 95°for 50 x 105 mm trunkings
10 0 106 19 Changeable external bend, from 60° to 120°for 50 x 105 mm trunkings
Flat angle10 0 107 86 90° fl at angle
End cap20 0 107 00 Left or right end cap
65
105
50
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819 to 821)
Selection chart p. 804-805Wiring capacity chart p. 823
809
for example xxxxxxxxxxxxxxxuniversal DLP trunking x - mm covertrunking and ttings
Whitelength: m
Flat junctionCat.No 0 107 35Changeable
internal angleCat.No 0 106 06
Changeablefl at angle
Cat.No 0 107 89
Changeable external angle
Cat.No 0 106 35
Cat.Nos for x trunking
ArteorMosaic
Compatible ranges
Pack Cat.Nos Universal trunking
Trunking with partition12 0 104 271 Supplied with:
- one 50 x 150 mm body- one fl exible 65 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation
20 0 106 92 Body joint, attached with adhesive(fi t at the end of installation)
10 0 108 01 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 3 components making the angle (parts for the top and bottom and the partition junction) on which the fl exible cover is fi tted
5 0 106 06 Changeable internal bend, from 85° to 95°for 50 x 150 and 50 x 195 mm trunkings
5 0 106 35 Changeable external bend, from 60° to 120°for 50 x 150 and 50 x 195 mm trunkings
Flat angle5 0 107 89 90° fl at angle
End cap10 0 107 03 Left or right end cap
Pack Cat.Nos Junctions
Flat junctions5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 06
Accessories50 0 106 81 Clip
100 0 308 81 Base for clamp
65 65
150
50
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819 to 821)
Selection chart p. 804-805Wiring capacity chart p. 823
810
for example xxxxxxxxxxxxxxxuniversal DLP trunking x - mm covertrunking and ttings
Whitelength: m
Cat.Nos for x trunking
Flat junctionCat.No 0 107 37
Changeable internal angle
Cat.No 0 106 50
Changeable external angle
Cat.No 0 106 38
Changeablefl at angle
Cat.No 0 107 98
ArteorMosaic
Compatible ranges
Selection chart p. 804-805Wiring capacity chart p. 823
Pack Cat.Nos Universal trunking
Trunking with partition4 0 104 671 Supplied with:
- one 50 x 170 mm body- one fl exible 65 mm width cover and two fl exible 40 mm width coversFits onto the whole trunking includinginternal and external anglesInstallation: can be used with Mosaic/Arteor rangesor DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation
20 0 106 92 Body joint, attached with adhesive(fi t at the end of installation)
10 0 108 01 Cover joint for 65 mm cover10 0 108 00 Cover joint for 40 mm cover
Angles and end capInternal and external bendsInclude the 4 components making the angle (parts for the top and bottom and the 2 partition junctions) on which the fl exible cover is fi tted
5 0 106 50 Changeable internal bend, from 85° to 95°for 50 x 170 and 50 x 195 mm trunkings
5 0 106 38 Changeable external bend, from 60° to 120°for 50 x 170 and 50 x 195 mm trunkings
Flat angle2 0 107 98 90° fl at angle
End cap5 0 107 10 Left or right end cap
Pack Cat.Nos Junctions
Flat junctions5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 50
Accessories50 0 106 82 Clip for 40, 65 and 85 mm covers
100 0 308 81 Base for clamp
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819-821)
40 65
170
40
50
811
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
Selection chart p. 804-805Wiring capacity chart p. 823
Wiring accessories supports and installation accessories (p. 819-821)
universal DLP trunking x - mm covertrunking and ttings
Whitelength: m
Cat.Nos for x trunking
Flat junctionCat.No 0 107 37
Changeable internal angle
Cat.No 0 106 50
Changeable external angle
Cat.No 0 106 38
Changeablefl at angle
Cat.No 0 107 95
ArteorMosaic
Compatible ranges
Pack Cat.Nos Universal trunking
Trunking with partition8 0 104 281 Supplied with:
- one 50 x 220 mm body- three fl exible 65 mm width coversFits onto the whole trunking includinginternal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation
20 0 106 92 Body joint, attached with adhesive(fi t at the end of installation)
10 0 108 01 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 4 components making the angle (parts for the top and bottom and the 2 partition junctions) on which the fl exible cover is fi tted
5 0 106 50 Changeable internal bend, from 85° to 95°for 50 x 170 and 50 x 195 mm trunkings
5 0 106 38 Changeable external bend, from 60° to 120°for 50 x 170 and 50 x 195 mm trunkings
Flat angle2 0 107 95 90° fl at angle
End cap5 0 107 05 Left or right end cap
Pack Cat.Nos Junctions
Flat junctions5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 50
Accessories50 0 106 81 Clip
100 0 308 81 Base for clamp
1: Number of metres in pack
65 65
220
65
50
812
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition20 0 104 631 Supplied with:
- one 35 x 105 mm body- one fl exible 85 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)
10 0 108 02 Cover joint
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 01 Changeable internal bend, from 85° to 95°for 35 x 80 and 35 x 105 mm trunking
10 0 106 21 Changeable external bend, from 60° to 120°for 35 x 80 and 35 x 105 mm trunking
Flat angle10 0 107 84 90° fl at angle
End cap20 0 107 01 For 35 x 105 mm trunking
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 01
Accessories50 0 106 82 Clip for 40, 65 and 85 mm covers
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
Flat junctionCat.No 0 107 35
Changeable internal angle
Cat.No 0 106 01Changeablefl at angle
Cat.No 0 107 84
Changeable external angle
Cat.No 0 106 21
Cat.Nos for x trunking
Whitelength: m
Compatible with all wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika, Synergy, Mallia, Belanko
Selection chart p. 804-805Wiring capacity chart p. 823
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819-821)
85
105
35
813
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition16 0 104 641 Supplied with:
- one 50 x 105 mm body- one fl exible 85 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)
10 0 108 02 Cover joint
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 02 Changeable internal bend, from 85° to 95°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
10 0 106 22 Changeable external bend, from 60° to 120°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
Flat angle90° angle
10 0 107 85 For 50 x 105 mm trunking
End cap20 0 107 02 For 50 x 105 mm trunking
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 02
Accessories50 0 106 82 Clip for 40, 65 and 85 mm covers
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
Flat junctionCat.No 0 107 35
Changeable internal angle
Cat.No 0 106 02Changeablefl at angle
Cat.No 0 107 85
Changeable external angle
Cat.No 0 106 22
Cat.Nos for x trunking
Whitelength: m
Compatible with all wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika, Synergy, Mallia, Belanko
Selection chart p. 804-805Wiring capacity chart p. 823
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819 to 821)
85
105
50
814
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
universal DLP trunking x - mm covertrunking and ttings
Whitelength: m
Flat junctionCat.No 0 107 35
Cat.Nos for x trunking
Selection chart p. 804-805Wiring capacity chart p. 823
Pack Cat.Nos Universal trunking
Trunking with partition8 0 104 701 Supplied with:
- one 50 x 195 mm body– two fl exible 85 mm width coversFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation
20 0 106 92 Body joint, attached with adhesive(fi t at the end of installation)
10 0 108 02 Cover joint
Angles and end capInternal and external bendsInclude the 3 components making the angle (parts for the top and bottom and the partition junction) on which the fl exible cover is fi tted
5 0 106 06 Changeable internal bend, from 85° to 95°for 50 x 150 and 50 x 195 mm trunkings
5 0 106 35 Changeable external bend, from 60° to 120°for 50 x 150 and 50 x 195 mm trunkings
Flat angle2 0 107 92 90° fl at angle
End cap5 0 107 11 Left or right end cap
Pack Cat.Nos Junctions
Flat junctions5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angle Cat.No 0 106 06
Accessories50 0 106 82 Clip for 40, 65 and 85 mm covers
100 0 308 81 Base for clamp
1: Number of metres in pack
Compatible with all wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika, Synergy, Mallia, Belanko
Changeablefl at angle
Cat.No 0 107 92
Changeable internal angle
Cat.No 0 106 06
Changeable external angle
Cat.No 0 106 35
Wiring accessories supports and installation accessories (p. 819 to 821)
85
195
85
50
815
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition12 0 104 651 Supplied with:
- one 50 x 150 mm body- one fl exible 130 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition
Length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)
10 0 108 04 Cover joint
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 02 Changeable internal bend, from 85° to 95°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
10 0 106 22 Changeable external bend, from 60° to 120°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
Flat angle5 0 107 89 90° fl at angle
End cap10 0 107 03 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm
wide profi le
5 0 107 37 For tap-off to a 105 mmwide profi le equipped with a 65 mm cover
5 0 107 36 For tap-off to a 105 mmwide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 For tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80, 50 x 105For use with internal angles Cat.No 0 106 02
Accessories50 0 106 86 Clip for 130 and 180 mm covers
100 0 308 81 Base for clamp
universal DLP trunking x - mm covertrunking and ttings
Cat.Nos for x trunking
Whitelength: m
Compatible with the following wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819 to 821) Mosaic (p. 866-867) Arteor (p. 396-397) sockets
Selection chart p. 804-805Wiring capacity chart p. 823
130
150
50
Flat junctionCat.No 0 107 36Changeable
internal angleCat.No 0 106 02Changeable
fl at angleCat.No 0 107 89
Changeable external angle
Cat.No 0 106 22
816
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition12 0 104 751 Supplied with:
- one 65 x 150 mm body- one fl exible 130 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition48 0 105 831 Separation partition for 65 mm depth
length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)10 0 108 04 Cover joint for 65 mm cover
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 03 Changeable internal bend, from 85° to 95°for 65 x 105/65 x 150 and 65 x 195 mm trunking
10 0 106 23 Changeable external bend, from 60° to 120°for 65 x 105/65 x 150 and 65 x 195 mm trunking
Flat angle2 0 107 90 90° fl at angle
End cap10 0 107 06 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 33 To tap-off to an 80 mm wide trunking
5 0 107 38 To tap-off to a 105 mm wide and 50 mm deep trunking
Angled junction5 0 107 64 To tap-off in an internal angle
to 35 x 80, 35 x 105, 50 x 80 or50 x 105 mm trunkingUsed with an internal angleCat.No 0 106 03 or 0 106 07
Accessories50 0 106 86 Clip for 130 and 180 mm covers
100 0 308 81 Base for clamp
universal DLP trunking x - mm cover trunking and ttings
Whitelength: m
Selection chart p. 804-805Wiring capacity chart p. 823
1: Number of metres in pack
Cat.Nos for x trunking
Flat junctionCat.No 0 107 38Changeable
internal angleCat.No 0 106 03
Changeablefl at angle
Cat.No 0 107 90
Changeable external angle
Cat.No 0 106 23
130150
65
Compatible with the following wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika
Wiring accessories supports and installation accessories (p. 819 to 821) Mosaic (p. 866-867) Arteor (p. 396-397) sockets
817
Red catalogue numbers: New products
universal DLP trunking x - mm cover trunking and ttings
Whitelength: m
1: Number of metres in pack
Cat.Nos for x trunking
Flat junctionCat.No 0 107 35
Changeablefl at angle
Cat.No 0 107 92
Changeable external angle
Cat.No 0 106 22
Changeable internal angle
Cat.No 0 106 02
Selection chart p. 804-805Wiring capacity chart p. 823
Compatible with the following wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika
Wiring accessories supports and installation accessories (p. 819 to 821) Mosaic (p. 866-867) Arteor (p. 396-397) sockets
Pack Cat.Nos Universal trunking
Trunking without partition4 0 104 691 Supplied with:
- one 50 x 195 mm body- one fl exible 180 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition24 0 105 821 Separation partition length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)10 0 108 06 Cover joint
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 02 Changeable internal bend, from 85° to 95°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
10 0 106 22 Changeable external bend, from 60° to 120°for 50 x 80/50 x 105/50 x 150 and50 x 195 mm trunkings
Flat angle2 0 107 92 90° fl at angle
End cap5 0 107 11 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 35 For tap-off to a 80 mm wide profi le
5 0 107 37 To tap-off to a 105 mm wide profi le equipped with a 65 mm cover
5 0 107 36 To tap-off to a 105 mm wide profi le equipped with a 85 mm cover
Angled junction5 0 107 63 To tap-off in an internal angle to 35 x 80,
35 x 105, 50 x 80 or 50 x 105 mmFor use with internal angle cat.no 0 106 06
Accessories50 0 106 86 Clip for 130 and 180 mm covers
100 0 308 81 Base for clamp
180195
50
818
for example xxxxxxxxxxxxxxx
Red catalogue numbers: New products
Pack Cat.Nos Universal trunking
Trunking without partition4 0 104 761 Supplied with:
- one 65 x 195 mm body- one fl exible 180 mm width coverFits onto the whole trunking includingin internal and external anglesInstallation: can be used with Mosaic/Arteor ranges or DIN rail equipmentLength 2 m
Partition48 0 105 831 Separation partition for 65 mm depth
length 2 m
Joints20 0 106 91 Body joint
For aligning bases during installation20 0 106 92 Body joint, attached with adhesive
(fi t at the end of installation)10 0 108 06 Cover joint
Angles and end capInternal and external bendsInclude the 2 components for the top andbottom of the trunking on which the fl exiblecover is fi tted
10 0 106 03 Changeable internal bend, from 85° to 95°for 65 x 105/65 x 150 and 65 x 195 mm trunking
10 0 106 23 Changeable external bend, from 60° to 120°for 65 x 105/65 x 150 and 65 x 195 mm trunking
Flat angle2 0 107 93 90° fl at angle
End cap5 0 107 07 Left or right end cap
Pack Cat.Nos Junctions
Flat junction5 0 107 33 To tap-off to an 80 mm wide
trunking
5 0 107 38 To tap-off to a 105 mm wideand 50 mm deep trunking
Angled junction5 0 107 64 To tap-off in an internal angle
to 35 x 80, 35 x 105, 50 x 80 or50 x 105 mm trunkingUsed with an internal angleCat.No 0 106 03 or 0 106 07
Accessories50 0 106 86 Clip for 130 and 180 mm covers
100 0 308 81 Base for clamp
universal DLP trunking x - mm cover trunking and ttings
Flat junctionCat.No 0 107 33
Changeablefl at angle
Cat.No 0 107 93
Cat.Nos for x trunking
Whitelength: m
Selection chart p. 804-805Wiring capacity chart p. 823
1: Number of metres in pack
Wiring accessories supports and installation accessories (p. 819 to 821)
Changeable external angle
Cat.No 0 106 23
Changeable internal angle
Cat.No 0 106 03
180195
65
Compatible with the following wiring accessory ranges: Arteor, Mosaic, Galea Life, Valena, Suno, Cariva, Niloe, Kaptika
819
for example xxxxxxxxxxxxxxxMosaicTM Programme socket outlets
Pack Cat.Nos Sockets for installation on DLP trunkingMosaic sockets with shutters withconnection at both sides for mountingon 65 and 85 mm cover DLP trunking inconjunction with supports and plates fortrunking (see p. 804-805)Direct connection requiring no tools,intuitive disconnection without dismantlingthe support
Standard
TTamperproof Automatic terminals - German standard
10 0 774 01 0 774 21 2P+E
10 0 774 02 0 774 22 2 x 2P+E
10 0 774 03 0 774 23 3 x 2P+E
5 0 774 04 0 774 24 4 x 2P+E
Red10 0 774 11 2P+E
10 0 774 12 2 x 2P+E
10 0 774 13 3 x 2P+E
5 0 774 14 4 x 2P+E
Mosaic socket outlet Cat.No 0 774 02 with 4 modules supportMosaic RJ 45 socket outlet with 2 modules support Cat.No 0 109 54
Mosaic socket outlet Cat.No 0 774 03 with 6 modules supportMosaic socket outlet Cat.No 0 774 23 with 4 modules support
Mosaic 2 x 4 modules support Cat.No 0 109 54 for cover width 65 mm
Pack Cat.Nos Sockets for installation on DLP trunking (continued)
Standard
TTamperproof Screw terminals - German standard
10 0 776 01 0 776 21 2P+E
10 0 776 02 0 776 22 2 x 2P+E
10 0 776 03 0 776 23 3 x 2P+E
5 0 776 04 0 776 24 4 x 2P+E
Red10 0 776 11 2P+E
10 0 776 12 2 x 2P+E
10 0 776 13 3 x 2P+E
5 0 776 14 4 x 2P+E
Tamperproof insert10 0 502 99 Tamperproof insert for socket
Fits directly into the plug
Red catalogue numbers: New products
820
wiring accessories supports for DLP trunking
Pack Cat.Nos Supports for mounting Mosaic and Arteor wiring accessoriesClick-on supports which can be fitted side by sideSupplied with finishing plate
For 40 mm cover5 0 109 10 1 module
For 65 mm cover20 0 109 52 2 modules
20 0 109 54 4 modules
10 0 109 56 6 modules
10 0 109 58 8 modules
For 85 mm cover20 0 109 92 2 modules
20 0 109 93 3 modules
20 0 109 94 4 modules
10 0 109 96 6 modules
10 0 109 98 8 modules
10 0 109 27 Insulation unit for 2 modules. Can be fittedtogether to create 4, 6 and 8 modulessupports
Supports for mounting Mosaic wiring accessories alongside the trunking Use 1 frame plus 1 link accessory plus 1 slide for 35 mm width trunking and add 1 spacer for 50 mm width trunkingMosaic frames. For 65, 85 and 130 mm covers
10 0 316 21 2 x 4 modules
10 0 316 22 3 x 4 modules
Pack Cat.Nos Universal supports for 60 mm fixing centres wiring accessoriesFor Galea Life, Valena, Suno, Cariva, Niloe and Kaptika
For 85 mm cover10 0 109 13 1 gang
5 0 109 23 2 gang
5 0 109 33 3 gang
For 130 mm cover5 0 109 14 1 gang
5 0 109 24 2 gang
5 0 109 34 3 gang
10 0 109 17 Insulation unit for 1 module
Mounting of Synergy, Mallia and Belanko wiring accessoriesBack boxes for mounting British standard wiring accessories on 85 mm cover
Depth 25 mm5 6 208 16 1 gang
5 6 208 26 2 gang
Depth 35 mm5 6 208 17 1 gang
5 6 208 27 2 gang
Support for mounting Hypra socket wiring accessories
5 0 109 00 For 130 mm cover
Supports for mounting Din-rail equipment wiring accessoriesFor 65 mm cover
5 0 109 25 2 modules
For 85 mm cover5 0 109 35 3 modules
For 130 mm cover5 0 109 65 6 modules
2 x 2 modules Mosaic support Cat.No 0 109 52 for cover 65 mm
2 modules Mosaic support Cat.No 0 109 52 for cover 65 mm
2 modules Mosaic support Cat.No 0 109 92 8 modules Mosaic support Cat.No 0 109 98
821
Pack Cat.Nos Cutting accessories for trunking
1 0 306 98 DLPlus cutting unit for PVC DLPFor cutting all plastic bodiesAvoids vibration when cutting basesand covers. AluminiumDim.: 225 x 142 x 76 mm
Insulation accessory10 0 304 18 Base joint. Adjustable wall insulation joint,
supplied in 5 m lengthsProvides continuity between the trunkingand the wall, in particular in internal angles
Fixing accessories for trunkingFor fixing all plastic profiles
Wall plugs for immediate fixingNo screws or nails required
100 0 308 98 For mini-trunking
100 0 308 99 For mini-trunking, skirting trunkingand trunking
Cartridge of Neoprene12 0 309 49 Adhesive for glue gun
DLP rapid wall plug200 0 308 97 For 10 mm min. plasterboard walls at least 20 mm
away from the concrete surfaceFor fixing DLP plastic trunking in a single operationUsed with a special tool for drill (Ø8 mm), supplied ineach pack of 200 wall plugsTensile resistance: 25 kg
Spit end cap for DLP trunking100 0 106 95 For rapid fixing of trunkings with the Spit Pulsa 700 E
(use 20 mm Spit nails)
Junction boxes for DLP trunkingFitted with current separatorCable entry possible via the bottom of the box
White junction boxes10 0 313 50 Dim.: 163 x 163 x 65 mm
(except profile height 80 mm)5 0 313 51 Dim.: 200 x 200 x 83 mm5 0 313 52 Dim.: 250 x 250 x 83 mm
VDI cable management accessoriesTo be fitted on the standard accessories (angles and junctions). For all trunking sizes except35 x 80 trunking and in compartments with40 mm width cover
5 0 107 80 Accessory for internal angle5 0 107 81 Accessory for external angle5 0 107 82 Accessory for flat angle5 0 107 83 Accessory for flat junction
accessoriesuniversal DLP trunking
0 308 990 308 98
0 309 49
0 308 97 0 106 95 0 313 50 0 308 81
Junction to floor duct Cat.No 0 107 71 + 0 106 90
Junction for change of plane Cat.No 0 107 71/72
Wall feedthrough Cat.No 0 106 98/99
Flate junctionCat.No 0 107 32
Pack Cat.Nos Junction and routing accessories
Base for Nylbloc auto terminals10 0 343 98 For up to 3 screwless connection terminals Nylbloc
auto (Cat.Nos 0 343 22/23/25/28)Direct fixing:- in top of Plexo boxes and industrial plastic cabinets≥ 130 x 130 mm- on flat bar 12 x 2 mm- in bottom of universal and aluminium DLP trunkings (from 50 x 80 mm)Screw fixing:- in bottom of Plexo boxes ≥ 105 x 105 mm andindustrial plastic cabinets- universalFixing on rail with accessory Cat.No 0 048 11 (p. 190)Accessible test socketMarking zone with felt tip pen Cat.No 0 395 98 (p. 304)
Connection strips20 0 312 10 Connection strips with 4 x 4 mm2 terminals
for junction boxes
For high current cables100 0 308 81 Base for cable ties
Flat junctionsBase junctions
10 0 107 32 To tap-off to a profile smaller than 50 x 105
5 0 107 33 To tap-off to an 80 mm width trunking
Accessories for separation partitionAllow bottom compartment cables to pass through the separation partition in case of a flat junction
5 0 107 42 For 50 mm height separation partition5 0 107 43 For 65 mm height separation partition
Junctions for change of planeTo tap-off from wall to ceiling, for example to supplypower to a luminaire
5 0 107 70 For cover 40 mm5 0 107 71 For cover 65 mm5 0 107 72 For cover 85 mm5 0 107 73 For trunking Cat.No 0 104 24
Junctions between floor duct and trunkingTo tap-off to floor duct Cat.No 0 328 00 (p. 837)
5 0 107 71+0 106 90
For cover 65 mm
5 0 107 72+0 106 90
For cover 85 mm
Wall feedthroughsProvides a finish between the trunking and the wall
5 0 106 98 For trunking 80 to 150 mm width5 0 106 99 For trunking 195 to 220 mm width
NEW
NEW
Red catalogue numbers: New products
822 823
Size Number of compartments
Cover width
Cross section (mm2)
Capacity Ø maxMaximum wiring capacity (for a specific conductor type)
1.5 mm2 2.5 mm2 4 mm2 6 mm2 3 x 1.5 mm2 3 x 2.5 mm2 Cat. 6 UTP and FTP
35 x 80
Cat.No 0 104 611 compartment 65
2240 Max 33 135 100 88 65 19 14 44
690 With Mosaic and Arteor support 2 x 14 41 31 27 20 6 4 13
1030 With DIN-rail equipment support 2 x 16 62 46 40 30 9 6 20
50 x 80
Cat.No 0 104 62
1 compartment 65
3340 Max 39 202 150 131 97 29 21 66
1790 With Mosaic and Arteor support 2 x 18 108 80 70 52 15 11 35
2130 With DIN-rail equipment support 2 x 24 129 95 84 62 18 13 42
50 x 105
Cat.No 0 104 24
1 compartment 65
4380 Max 2 x 36 265 196 172 127 38 28 87
2830 With Mosaic and Arteor support 2 x 26 171 127 111 82 25 18 56
3170 With DIN-rail equipment support 2 x 30 192 142 125 92 28 20 63
50 x 150
Cat.No 0 104 27
2 compartments
65
3060 Max 42 185 137 120 89 27 20 61
1510 With Mosaic and Arteor support 18 91 67 59 43 13 9 30
1850 With DIN-rail equipment support 24 112 83 73 53 16 12 36
65
3060 Max 42 185 137 120 89 27 20 61
1510 With Mosaic and Arteor support 18 91 67 59 43 13 9 30
1850 With DIN-rail equipment support 24 112 83 73 53 16 12 36
50 x 170
Cat.No 0 104 67
3 compartments
40side
2050 Max 28 124 92 80 59 18 13 40
1530 With Mosaic and Arteor support 24 92 68 60 44 13 10 30
65middle
2770 Max 42 167 124 109 80 24 18 55
1220 With Mosaic and Arteor support 14 73 54 48 35 10 7 24
1560 With DIN-rail equipment support 3 x 16 94 70 61 45 13 10 31
40side
2050 Max 28 124 92 80 59 18 13 40
1530 With Mosaic and Arteor support 24 92 68 60 44 13 10 30
50 x 220
Cat.No 0 104 28
3 compartments
65side
3060 Max 42 185 137 120 89 27 20 61
1510 With Mosaic and Arteor support 18 91 67 59 43 13 9 30
1850 With DIN-rail equipment support 24 112 83 73 53 16 12 36
65middle
2770 Max 42 167 124 109 80 24 18 55
1220 With Mosaic and Arteor support 14 73 54 48 35 10 7 24
1560 With DIN-rail equipment support 3 x 16 94 70 61 45 13 10 31
65side
3060 Max 42 185 137 120 89 27 20 61
1510 With Mosaic and Arteor support 18 91 67 59 43 13 9 30
1850 With DIN-rail equipment support 24 112 83 73 53 16 12 36
n Wiring capacity
65 mm cover universal DLP trunking
85 mm cover universal DLP trunking
130 and 180 mm cover universal DLP trunking
Size Number of compartments
Cover width
Cross section (mm2)
Capacity Ø maxMaximum wiring capacity (for a specific conductor type)
1.5 mm2 2.5 mm2 4 mm2 6 mm2 3 x 1.5 mm2 3 x 2.5 mm2 Cat. 6 UTP and FTP
35 x 105
Cat.No 0 104 631 compartment 85
2850 Max 33 172 128 112 83 25 18 56
820 With Mosaic and Arteor support 2 x 16 49 36 32 23 7 5 16
590 With universal support 2 x 16 35 26 23 17 5 3 11
980 With DIN-rail equipment support 2 x 16 59 44 38 28 8 6 19
50 x 105
Cat.No 0 104 64
1 compartment 85
4300 Max 42 260 113 169 125 38 28 85
2270 With Mosaic and Arteor support 2 x 24 137 102 89 66 20 14 45
1680 With universal support 2 x 16 99 73 64 47 14 10 32
2430 With DIN-rail equipment support 2 x 21 147 109 95 70 21 15 48
50 x 195
Cat.No 0 104 70
2 compartments
85
3940 Max 42 238 177 155 114 35 25 78
1910 With Mosaic and Arteor support 26 115 85 75 55 16 12 38
1280 With universal support 18 77 57 50 37 11 8 25
2070 With DIN-rail equipment support 24 125 93 81 60 18 13 41
85
3940 Max 42 238 177 155 114 35 25 78
1910 With Mosaic and Arteor support 26 115 85 75 55 16 12 38
1280 With universal support 18 77 57 50 37 11 8 25
2070 With DIN-rail equipment support 24 125 93 81 60 18 13 41
Size Number of compartments
Cover width
Cross section (mm2)
Capacity Ø maxMaximum wiring capacity (for a specific conductor type)
1.5 mm2 2.5 mm2 4 mm2 6 mm2 3 x 1.5 mm2 3 x 2.5 mm2 Cat. 6 UTP and FTP
50 x 150
Cat.No 0 104 65
1 compartment 130
6440 Max 2 x 42 390 289 254 187 57 42 128
2360 With universal support 2 x 30 143 106 93 68 20 15 47
3200 With DIN-rail equipment support 2 x 20 194 143 126 93 28 20 63
2440 With Hypra support 2 x 25 147 109 96 71 21 15 48
50 x 195
Cat.No 0 104 69
1 compartment 180 8460 Max 3 x 42 513 380 333 246 75 55 169
65 x 150
Cat.No 0 104 75
1 compartment 130
8200 Max 2 x 55 497 368 323 238 72 53 163
4120 With universal support 2 x 40 249 185 162 120 36 27 82
4960 With DIN-rail equipment support 2 x 33 300 223 195 144 44 32 99
4200 With Hypra support 2 x 28 254 188 165 122 37 27 83
65 x 195
Cat.No 0 104 76
1 compartment 180 11240 Max 3 x 54 681 505 443 327 99 73 224
universal trunking
Classification EN 50085-2-1 Level6.1 Void6.2 Resistance to impact for installation and application 2.0 J
6.3 Minimum storage and transport temperature - 25 °C
6.3 Minimum installation and application temperature - 5 °C
6.3 Maximum application temperature + 60 °C
6.4 Resistance to flame propagation Non-flame propagating
6.5 Electrical continuity characteristic Without electrical continuity characteristic
6.6 Electrical insulating characteristic With electrical insulating characteristic
6.7 Degrees of protection provided by enclosure IP 40
6.9 System access cover retention With a tool
6.101 Position when surface mounted Wall fixed, ceiling fixed, wall fixed and supported by the floor or other horizontal surface
6.102 Prevention of contact between liquids and insulated conductors and live parts in case of CTS/CDS mounted in a skirting position and wet-treatment of floor Instructions restricting the installation position
6.103 The functions provided Type 2: 0 104 32/33/52/53, type 3: other Cat.Nos
Rated current 500 V
Against mechanical shocks IK 07
n New standard EN 50085-2-1
Composition and functions of universal DLP trunking
Trunking Trunking and accessories Angles Flat junction(3) Supports for wiring
accessories
Cross-section (mm2)
Number of compartments
Covers width (mm)
Size(mm)
Bodies Covers Separation partitions(2)
End cap(2) Cover joints
Internal angle(1)
85 to 95°
External angle(1)
60 to 120°
Flat angle(1) To width 80 mm(2)
To width 105 mm(2)
Trunking for mounting of devices with support - 65 mm cover
1
6535 x 80
0 104 61 (body and cover
complete)0 105 84 0 107 22 0 108 01 0 106 01 0 106 21 0 107 67 0 107 35 - (3) 2240
6550 x 80
0 104 62 (body and cover
complete)0 105 82 0 107 22 0 108 01 0 106 02 0 106 22 0 107 67 0 107 35 - (3) 3340
6550 x 105
0 104 24 (body and cover
complete)0 105 82 0 107 00 0 108 01 0 106 05 0 106 19 0 107 86 0 107 39 0 107 40 (3) 4380
2
65 6550 x 150
0 104 27 (body and cover
complete)0 105 82 0 107 03 2 x 0 108 01 0 106 06 0 106 35 0 107 89 0 107 35 0 107 36
or 0 107 37 (3) 3060/3060
3
40 65 4050 x 170
0 104 67 (body and cover
complete)0 105 82 0 107 10 2 x 0 108 00
+ 0 108 01 0 106 50 0 106 38 0 107 98 0 107 35 0 107 36 or 0 107 37 (3) 2 x
2050/2770
65 65 6550 x 220
0 104 28 (body and cover
complete)0 105 82 0 107 05 3 x 0 108 01 0 106 50 0 106 38 0 107 95 0 107 35 0 107 36
or 0 107 37 (3) 2 x 3060/2770
Trunking for mounting of devices with support - 85 mm cover
1
8535 x 105
0 104 63 (body and cover
complete)0 105 82 0 107 01 0 108 02 0 106 01 0 106 21 0 107 84 0 107 35 0 107 36 (4) 2850
8550 x 105
0 104 64 (body and cover
complete)0 105 82 0 107 02 0 108 02 0 106 02 0 106 22 0 107 85 0 107 35 0 107 36
or 0 107 37 (4) 4300
2
85 8550 x 195
0 104 70 (body and cover
complete)0 105 82 0 107 11 2 x 0 108 02 0 106 06 0 106 35 0 107 92 0 107 35 0 107 36
or 0 107 37 (4) 3940
Trunking for mounting of devices with support - 130 mm cover
1
13050 x 150
0 104 65 (body and cover
complete)0 105 82 0 107 03 0 108 04 0 106 02 0 106 22 0 107 89 0 107 35 0 107 36
or 0 107 37 (5) 6440
13065 x 150
0 104 75 (body and cover
complete)0 105 83 0 107 06 0 108 04 0 106 03 0 106 23 0 107 90 0 107 33 0 107 38 (5) 8200
Trunking for mounting of devices with support - 180 mm cover
1
18050 x 195
0 104 69 (body and cover
complete)0 105 82 0 107 11 0 108 06 0 106 02 0 106 22 0 107 92 0 107 35
0 107 36 or
0 107 37- 8460
18065 x 195
0 104 76 (body and cover
complete)0 105 83 0 107 07 0 108 06 0 106 03 0 106 23 0 107 93 0 107 33 0 107 38 - 11240
1: Classification and performance are for a mounting at an angle of 90°2: See mounting and assembling instructions on technical sheets, boxes or on www.legrand.fr3: Mosaic supports for wiring accessories, cover width 65 mm: Cat.Nos 0 109 10/52/54/56/584: Universal and Mosaic supports for wiring accessories, cover width 85 mm: Cat.Nos 0 109 13/23/33/92/93/94/96/985: Universal supports for wiring accessories cover width 130 mm: Cat.Nos 0 109 14/24/34
Type 1, type 2 distribution, type 3 installation