Foaming Agent in Rotational Moulding
-
Upload
rajeevsharma802 -
Category
Documents
-
view
233 -
download
0
Transcript of Foaming Agent in Rotational Moulding
-
8/9/2019 Foaming Agent in Rotational Moulding
1/12
-
8/9/2019 Foaming Agent in Rotational Moulding
2/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
-
8/9/2019 Foaming Agent in Rotational Moulding
3/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Exothermic CBAs , that gives off heat while they
decompose. And
Endothermic CBAs , that take up heat while they
decompose.
-
8/9/2019 Foaming Agent in Rotational Moulding
4/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Direct use of foaming agent
Use of Foam masterbatches
-
8/9/2019 Foaming Agent in Rotational Moulding
5/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Use of foam masterbatches instead of foaming agent.
Proper mould geometry with blunt radii
Correct mould rotation speed/ratios
Uniform & slow cooling of the mould
Proper venting of the mould
-
8/9/2019 Foaming Agent in Rotational Moulding
6/12
Improve thermal insulation
Improve stiffness.
Reduce Weight-strength Ratio.
Improve impact strength.
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
-
8/9/2019 Foaming Agent in Rotational Moulding
7/12
M.G.Polyblends has developed
foaming agent masterbatch based on
Exothermic blowing agent.
Available in White & light
yellow pulverized powder.
)
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
http://www.mg-polyblends.com/ -
8/9/2019 Foaming Agent in Rotational Moulding
8/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Uniformity in structure.
Better Processibility.
Fine cell structure than foaming Agent
Better result than foaming agent.
Not require much skills and technical know-how.
-
8/9/2019 Foaming Agent in Rotational Moulding
9/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
There is a lot of difference in processing temperature of the
polymer and the foaming agent due to which suitable results
are not achieved.
In a masterbatch , certain additives are added to lower the
decomposition temperature of the foaming agent making it
closer to melting point of the polymer and delivering excellent
results. Moreover the foaming agent is uniformly dispersed in
masterbatch as a result the cell structure is fine and uniform
-
8/9/2019 Foaming Agent in Rotational Moulding
10/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Bases of Comparison Rotofoam Masterbatch FoamingAgent
Structure formation Uniformity in structure Difficult or sometimes not
possible to get uniformity in
structure.
Thickness and cell structure Getting more thickness and
fine cell structure
Less thickness and cell
structure is not good ascompare to rotofoam
masterbatch.
Processibility Better Processibility Much difficult
Impact Strength Excellent impact strength Poor impact strength
Thermal Insulation Excellent thermal insulation Poor thermal insulation
-
8/9/2019 Foaming Agent in Rotational Moulding
11/12
The information given in this document is only a recommendation, believed to be reliable and is given in goodfaith but without warranty. Users are advised to test the product to ascertain the suitability for the intended use
Bases of Comparison RFM-01 RFM-10
Processing window Narrow : Ranges
between 190 oC 210
oC.
Wide : Ranges between
190 oC 250 oC.
Cell structure Fine Much finer
Heat Insulation Good Excellent
Thickness Good Excellent
Impact strength Good Excellent
Colour Light yellowishpulverized powder
Pure white pulverizedpowder
-
8/9/2019 Foaming Agent in Rotational Moulding
12/12
http://www.mg-polyblends.com/http://www.mgpolyblends.com/http://images.google.co.in/imgres?imgurl=http://www.floral-directory.com/flower.gif&imgrefurl=http://www.floral-directory.com/&usg=__6UTKBFno525jFtg7RPPYLs_ZVAg=&h=526&w=364&sz=11&hl=en&start=19&um=1&tbnid=G1R7FwvkCOBiRM:&tbnh=132&tbnw=91&prev=/images?q=FLOWER&hl=en&um=1http://images.google.co.in/imgres?imgurl=http://www.floral-directory.com/flower.gif&imgrefurl=http://www.floral-directory.com/&usg=__6UTKBFno525jFtg7RPPYLs_ZVAg=&h=526&w=364&sz=11&hl=en&start=19&um=1&tbnid=G1R7FwvkCOBiRM:&tbnh=132&tbnw=91&prev=/images?q=FLOWER&hl=en&um=1