Fn w 104 Hanger Brochure

8/9/2019 Fn w 104 Hanger Brochure

1/32

PIPE HANGERS, SUPPORTS& STRUT ACCESSORIES

www.fnw.com


2/32

An FNW fyi

To nd out more about these services, contact your localWolseley North American operating branch. For locations,visit www.ferguson.com or wolseleyinc.ca.

Valve AutomationServices AvailableFNW products are distributed throughWolseley North American operatingcompanies. These companiescontain an extensive array of Valve

Automation Centers throughout theregion and provide services directly,or through your local branch. Eachfacility offers a variety of valveautomation expertise for sizing,designing, sourcing, assembling, andtesting. This expertise is availableat any time from the engineeringof ce to the job site.


3/32

Type Description Figure Number PageHangers ........................ Hinged Split Ring .......................................................... 7001 ...................................... 6

Standard Duty Adjustable Clevis ..................................7005 ...................................... 7 Light Duty Adjustable Clevis ......................................... 7006 ...................................... 8 Adjustable Clevis for Copper Tube ............................... 7008 ...................................... 9 Adjustable Swivel Ring ................................................. 7010 .................................... 10 Felt Lined Adjustable Swivel Ring ................................7012 .................................... 10 Adjustable Swivel Ring for Copper Tube ......................7015 .....................................11 Adjustable J ................................................................ 7025 .................................... 12

Clamps ......................... Medium Split Horizontal Pipe Clamp ............................ 7020 .................................... 13 Riser Clamp ..................................................................7022 .................................... 14 Riser Clamp for Copper Tube ....................................... 7023 .................................... 14

Beam Clamps ............... Steel C-Clamp .............................................................. 7201 .................................... 15 Malleable Iron C-Clamp ................................................ 7202 .................................... 15 Jr. Beam Clamp ............................................................ 7203 .................................... 15 Wide Mouth Beam Clamp .............................................7204 .................................... 16 Universal Beam Clamp ................................................. 7806 .................................... 16 Right Angle Beam Clamp .............................................7868 .................................... 16 Window Type Strut to Beam Clamp .............................. 7801 .................................... 16 Strut to Beam Spreader Caps ...................................... 7802 .................................... 16 Square U-Bolt Strut to Beam Clamp (short) ................. 7803 .................................... 17 Square U-Bolt Strut to Beam Clamp (long) .................. 7804 .................................... 17 Notched Type Strut to Beam Clamp ............................. 7805 .................................... 17 Beam Clamp Retaining Strap ....................................... 7250 .................................... 17

Rollers .......................... Roller Trolley 4-Bearing Assembly ................................7865 .................................... 17Brackets........................ Bracket Channel 1-5/8 Channel 2-HL .......................... 7811 .................................... 18Pipe Support Systems .. 50# Pipe Support ..........................................................7701 .................................... 18

150# Pipe Support ........................................................7715 .................................... 18 300# Pipe Support ........................................................7730 .................................... 18 Elevation Kit ................................................................ELKITC .................................. 18

Channel Nuts ................ Long Spring Channel Nut .............................................7818 .................................... 19 No Spring Channel Nut ................................................. 7819 .................................... 19 No Spring Channel Nut ................................................. 7820 .................................... 19 Regular Spring Channel Nut ......................................... 7821 .................................... 19 Short Spring Channel Nut .............................................7822 .................................... 19 Top Spring Channel Nut ............................................... 7824 .................................... 19

End Caps ...................... PVC Channel End Cap (1-5/8) .................................... 7830 .................................... 20 Channel End Cap (1-5/8) ............................................7831 .................................... 20

Angle Fittings ................ No Twist 2-Hole Corner Angle Fitting............................ 7840 .................................... 20 2-Hole Corner Angle Fitting .......................................... 7841 .................................... 20 Cross Corner Angle Fitting ...........................................7842 .................................... 21 3-Way Cross Corner Angle Fitting ................................7843 .................................... 21 7-Hole Gusset Corner Angle Fitting .............................. 7844 .................................... 21 2-Hole Open 45 Corner Angle Fitting .......................... 7845 .................................... 21 2-Hole Closed 45 Corner Angle Fitting ........................ 7846 .................................... 21 4-Hole Open 45 Corner Angle Fitting .......................... 7847 .................................... 22 2-Hole Angle Brace .......................................................7848 .................................... 22

Flat Fittings ................... Square Washer Flat Fitting ...........................................7835 .................................... 22 Notched Square Washer Flat Fitting ............................. 7836 .................................... 22 Splice Plate Flat Fitting ................................................. 7837 .................................... 23 3-Hole Corner Plate Flat Fitting .................................... 7838 .................................... 23 4-Hole Tee Plate Flat Fitting ......................................... 7839 .................................... 23

Post Base ..................... Single Channel 2-Hole Base ........................................ 7850 .................................... 24 Single Channel 2-Hole Flush Base ............................... 7851 .................................... 24 Single Channel 4-Hole Standard ..................................7852 .................................... 24

Single Channel 4-Hole Base (tall) ................................7853 .................................... 24 Single Channel 4-Hole Base (short) ............................. 7855 .................................... 24Strut Clamps ................. Cushioned Pipe Strut Clamp ........................................ 7815 .................................... 25

Cushioned Tubing Strut Clamp ..................................... 7816 .................................... 25 Copper Tubing Strut Clamp .......................................... 7870 .................................... 26 EMT Strut Clamp ..........................................................7871 .................................... 26 O.D. Strut Clamp ..........................................................7872 .................................... 27 Rigid Strut Clamp .........................................................7873 .................................... 28 Universal Strut Clamp ................................................... 7874 .................................... 28 Pipe Wrap .....................................................................7862 .................................... 29

Attachments.................. Beam Connector ........................................................... 7501 .................................... 30 Ceiling Flange ............................................................... 7502 .................................... 30

Conduit/Pipe Clamps .... Rigid/EMT Clamp.......................................................... 7310 .................................... 30 Copper Pipe Clamp ...................................................... 7311 .................................... 30

Shields .......................... Insulation Protection Shields ........................................ 7750 .................................... 31 Insulation Protection Shields (Domestic) ......................7751 .................................... 31 Light Duty Insulation Protection Shields .......................7753 .................................... 31

Index


4/32

4 Phone: 503-287-8383 ~ Fax: 503-281-9677 ~ www.FNW.com

Material Speci cations

Finishes

Malleable Iron ................................................................................................................ ASTM A47 Grade 32510Carbon Steel.............................................................................................................................ASTM A283 Gr. CCarbon Steel..............................................................................................................ASTM A1011-00 SS GR 33Carbon Steel..............................................................................................................ASTM A1011-00CS Type B304 Stainless Steel ..........................................................................................................ASTM A240 (Type 304)

P ...... PlainNo nish applied

Z ...... Electroplated Zinc (Electro-Galvanized)Electroplating deposits zinc on the surface of the steel by electrolysis from a bath of zinc salts. This coatingis recommended for relatively dry indoor use. This is the standard coating for most FNW strut accessoryproducts. The thickness of zinc applied in this method is between 0.2 mils to 0.5 mils [5.1 m to 12.7 m]and meet ASTM B633 SC3 Type I.or Hot Dip Galvanized After FabricationThe steel is zinc coated by hot dipping the fabricated product. The product is dipped in molten zinc andis completely covered on all surfaces. This coating is generally recommended for outdoor use. The zinccoating thickness is typically 2.6 mils [66.0 m ] or 1.5 oz. per square foot [0.46 kg per square meter] perside.

Y ...... Yellow Zinc Dichromate A 0.5 mil [12.7 m] electro-galvanized zinc plating meeting ASTM B633 SC3 Type I is applied to the surfaceof the metal. Yellow Dichromate is applied over the zinc. This results in a yellowish-gold appearance andacts as a nonporous barrier sealant that is corrosion resistant and can be painted.

C ...... Copper Zinc Dichromate A 0.5 mil [12.7 m] electro-galvanized zinc plating meeting ASTM B633 SC3 Type I is applied to thesurface of the metal. Copper Zinc Dichromate is applied over the zinc. This results in a copper coloredappearance and acts as a nonporous barrier sealant that does not react adversely with copper pipe ortubing.or Copper (Electrolytic)Electro-copper plated

G ...... Green E-Coat An 8-step electro-deposition epoxy coating. Following a thorough cleaning and phosphate rinse the epoxyis applied by immersing the part in liquid epoxy to ensure coverage in crevices and dif cult areas. It isthen baked on creating a 0.7 to 0.9 mil [18 23 m] thick coating. This process negates drips and sagsand produces a coating that withstands 1000 hours or more in a salt spray test. This coating is also anexcellent base should the part need to be painted or powder coated before or after installation.

S ...... Stainless SteelProduct made in 304 Stainless Steel - ASTM A240 (Type 304)

EP .... Epoxy Plated (Zinc Colored) A highly durable and corrosion resistant coating system. See page 5 for details.

EC.... Epoxy Plated (Copper Colored) A highly durable and corrosion resistant coating system. See page 5 for details.

Approvals & Standards

Where indicated, FNW hanger products have the following approvals or are made to the following standards:MSS SP-58MSS SP-69WW-H-171NFPA 13UL Category VXFT/VXFT7 (UL 203 / ULC/ORD-C203)FM Class 1951

Epoxy plating is tested according to: ASTM B117-03 (Epoxy Plating Test) ASTM D 3359-08 (Epoxy Plating Test) ASTM D 3363-05 (Epoxy Plating Test)

Bolt and nut hardware dimensions for epoxy plated products per: ASME B.18.2.1 (Bolt) ASME B.18.2.2 (Nut)


5/32

5Phone: 503-287-8383 ~ Fax: 503-281-9677 ~ www.FNW.com

Epoxy Plated Finish

FNW EP and EC designated hangers and clamps come standard with epoxy plating that uses a moreenvironmentally friendly method than epoxy coatings that use phosphates and heavy metals. The eight stepprocess results in a superior coating that both enhances corrosion resistance and appearance.

Water Clean Degrease Water Clean Bonderite Water Clean Pre-Heat Powder Coating Curing

Load Unload

Eight Step Epoxy Plating Process1. Water Clean - Initial cleaning after forming.2. Degrease - An alkaline solution to removes oils, lubrication grease, soil, and metal oxides.3. Water Clean - Removes alkaline solution.4. Bonderite - Surface pretreatment using Bonderite NT-1 (see below).5. Water Clean - Post-vitri cation cleaning.6. Pre-Heat - Preheating prior to powder coating.7. Powder Coating - Epoxy is applied to minimum thickness of 0.05mm.8. Curing - Heated to a temperature of 392F (200C).

0 1 m

Bonderite Nanoparticles

0 1 m

Iron PhosphateBonderite NT-1 is a nano-ceramic vitri cation surfacepretreatment that creates a cohesive, inorganic, very denselayer for outstanding corrosion protection that is superior toiron phosphating. Speci cally formulated for use on metalsurfaces like steel, it is absolutely uniform and is free ofany phosphates or toxic heavy metals and does not requirepassivation. The nanotechnology also produces a smooth

nish.

About Bonderite NT-1

Bonderite and NT-1 are trademarks and/or registered trademarks of Henkel andaffiliates.

Superior Corrosion Resistance

FNW epoxy platedhanger after 240

hour salt spray testat 20% solution

Typical electro-zincplated hanger after240 hour salt spraytest at 20% solution

No Corrosion andStill Smooth

Corrosion and VeryPitted

FNW hangers and clamps with epoxy plating are testedin a 20% salt spray solution that exceeds ASTM B 117-03salt solution requirements by a factor of 4.

After 240 hours in a salt spray (fog) apparatus, theFNW hanger with epoxy plating showed little to no signsof corrosion or pitting and the nish was still smooth.Compare FNWs to a typical electro-zinc plated hangerthat shows signi cant corrosion and pitting after the sametest. It is easy to see that FNWs epoxy plating, offered asstandard, is the superior nish.


6/32


Pipe SizeA

(Rod Size)

B (in.) Pipe Size C (in.) Max. Load Weights (oz.)

in. mmPlain &

ZincCopper in. mm

Plain &Zinc

Copper Lbs.Plain &

ZincCopper

3/8 17.2 3/8-16 0.66 0.66 3/8 17.2 2.06 1.78 180 1.66 1.341/2 21.3 3/8-16 0.75 0.75 1/2 21.3 2.22 1.97 180 1.76 1.623/4 26.6 3/8-16 0.84 0.84 3/4 26.6 2.50 2.25 180 2.08 1.801 33.4 3/8-16 0.97 0.97 1 33.4 2.75 2.44 180 2.36 2.08

1-1/4 42.1 3/8-16 1.16 1.13 1-1/4 42.1 3.22 2.78 180 3.10 2.401-1/2 48.2 3/8-16 1.28 1.25 1-1/2 48.2 3.44 3.06 180 3.46 2.82

2 60.3 3/8-16 1.53 1.47 2 60.3 3.94 3.53 180 4.41 3.772-1/2 73.0 1/2-13 1.94 1.88 2-1/2 73.0 4.75 4.44 300 7.65 6.81

3 88.9 1/2-13 2.56 2.16 3 88.9 5.38 4.94 300 9.17 7.514 114.3 1/2-13 2.75 2.63 4 114.3 6.41 5.94 300 10.58 9.28

Hangers

FIGURE 7001 - Hinged Split Ring

Finish: Plain, Zinc, or Copper MSS SP-58, type 12Material: Malleable Iron, ASTM A47 Grade 32510

Pipe Size Catalog Number in. mm Plain Zinc Copper

3/8 17.2 FNW7001PC FNW7001ZC FNW7001CC1/2 21.3 FNW7001PD FNW7001ZD FNW7001CD3/4 26.6 FNW7001PF FNW7001ZF FNW7001CF1 33.4 FNW7001PG FNW7001ZG FNW7001CG

1-1/4 42.1 FNW7001PH FNW7001ZH FNW7001CH1-1/2 48.2 FNW7001PJ FNW7001ZJ FNW7001CJ

2 60.3 FNW7001PK FNW7001ZK FNW7001CK2-1/2 73.0 FNW7001PL FNW7001ZL FNW7001CL

3 88.9 FNW7001PM FNW7001ZM FNW7001CM4 114.3 FNW7001PP FNW7001ZP FNW7001CP

A - Rod size (hanger rod and nuts not included)B - Center of pipe to top of hanger C - Width of hanger


7/32


Hangers

FIGURE 7005 - Standard Duty Adjustable Clevis Hangers

A - Rod size (hanger rod and nuts not included)B - Bottom of pipe to top of hanger C - Center of pipe to top of hanger D - Rod take out (center of pipe to bottom of hanger

rod)E - Minimum thread length of hanger rodF - Adjustment, top of cross bolt to bottom of hanger

rod nut inside hanger 1-1/2 to 12

1/2 to 1-1/4

Catalog Number Pipe Size A

(Rod Size)

B C D

in. mm in. mm in. mm in. mm

FNW7005EP0050 1/2 21.3 3/8-16 1-15/16 49.00 1-7/16 37.55 3/8 9.5FNW7005EP0075 3/4 26.6 3/8-16 2-1/4 57.40 1-3/4 43.25 5/8 15.FNW7005EP0100 1 33.4 3/8-16 2-11/16 68.00 2 50.50 7/8 22.5FNW7005EP0125 1-1/4 42.1 3/8-16 3-1/4 82.00 2-3/8 59.90 1-1/4 31.FNW7005EP0150 1-1/2 48.2 3/8-16 3-7/8 98.00 2-7/8 72.85 1-3/4 44.FNW7005EP0200 2 60.3 3/8-16 4-5/16 109.00 3-1/16 77.85 1-15/16 49.FNW7005EP0250 2-1/2 73.0 1/2-13 5-1/8 130.20 3-5/8 92.65 2-5/16 57.FNW7005EP0300 3 88.9 1/2-13 5-15/16 150.10 4-1/8 104.40 2-3/4 69.FNW7005EP0350 3-1/2 101.6 1/2-13 6-1/2 165.50 4-7/16 113.45 3-1/16 78.FNW7005EP0400 4 114.3 5/8-11 7-7/16 189.00 5-1/8 130.35 3-11/16 93.FNW7005EP0500 5 141.3 5/8-11 9-1/4 233.80 6-3/8 161.40 4-5/8 117FNW7005EP0600 6 168.2 3/4-10 10-1/2 267.30 7-1/8 181.15 5-5/16 134.8FNW7005EP0800 8 219.1 3/4-10 12-15/16 328.40 8-1/2 216.35 6-1/2 164FNW7005EP1000 10 273.1 7/8-9 15-1/2 394.00 10 254.45 7-5/8 194FNW7005EP1200 12 323.9 7/8-9 18-5/8 473.10 12-1/8 307.90 9-3/4 247

Catalog Number Pipe Size E F

Bolt SizeDesign Load Weight

in. mm in. mm in. mm Lbs. kN Lbs.

FNW7005EP0050 1/2 21.3 2-1/2 63.5 7/16 11.1 1/4-20UNC 610 2.71 0.15FNW7005EP0075 3/4 26.6 2-1/2 63.5 1/2 12.7 1/4-20UNC 610 2.71 0.17FNW7005EP0100 1 33.4 2-1/2 63.5 5/8 15.9 1/4-20UNC 610 2.71 0.20FNW7005EP0125 1-1/4 42.1 2-1/2 63.5 7/8 22.2 1/4-20UNC 610 2.71 0.29FNW7005EP0150 1-1/2 48.2 2-1/2 63.5 1-3/16 30.2 1/4-20UNC 610 2.71 0.32

FNW7005EP0200 2 60.3 2-1/2 63.5 1-5/8 41.3 1/4-20UNC 610 2.71 0.39FNW7005EP0250 2-1/2 73.0 2-1/2 63.5 2 50.8 5/16-18UNC 1130 5.02 0.67FNW7005EP0300 3 88.9 2-1/2 63.5 2 50.8 5/16-18UNC 1130 5.02 0.83FNW7005EP0350 3-1/2 101.6 2-1/2 63.5 2 50.8 5/16-18UNC 1130 5.02 0.91FNW7005EP0400 4 114.3 2-1/2 63.5 2 50.8 5/16-18UNC 1430 6.36 1.25FNW7005EP0500 5 141.3 2-1/2 63.5 2 50.8 3/8-16UNC 1430 6.36 2.03FNW7005EP0600 6 168.2 3 76.2 2 50.8 3/8-16UNC 1940 8.62 3.56FNW7005EP0800 8 219.1 3-1/2 88.9 2-5/16 58.7 5/8-11UNC 2000 8.89 4.89FNW7005EP1000 10 273.1 3-1/2 88.9 2-5/16 58.7 3/4-10UNC 3600 16.00 8.64FNW7005EP1200 12 323.9 3-1/2 88.9 2-5/16 66.7 3/4-10UNC 3800 16.89 10.1

UL/FM Approved - Sizes 2-1/2 to 8

Finish: Epoxy PlatedColor: ZincMSS SP-58, Type 1

Federal Speci cation WW-H-171, Type 1


8/32


9/32


Hangers

FIGURE 7008 - Adjustable Clevis Hangers for Copper Tube

A - Rod size (hanger rod and nuts not included)B - Bottom of pipe to top of hanger C - Center of pipe to top of hanger D - Rod take out (center of pipe to bottom of hanger

rod)E - Minimum thread length of hanger rodF - Adjustment, top of cross bolt to bottom of hanger

rod nut inside hanger 2 to 6

1/2 to 1-1/2


(Rod size)

B C D

in. mm in. mm in. mm in. mm

FNW7008EC0050 1/2 15.9 3/8-16 1-3/4 45.00 1-7/16 36.20 3/8 9.20FNW7008EC0075 3/4 22.2 3/8-16 2 51.40 1-1/2 39.40 1/2 12.40FNW7008EC0100 1 28.6 3/8-16 2-7/16 61.70 1-7/8 46.55 3/4 19.55FNW7008EC0125 1-1/4 34.9 3/8-16 2-3/4 71.10 2-1/16 52.55 1 25.55FNW7008EC0150 1-1/2 41.3 3/8-16 3-3/16 82.00 2-3/8 60.30 1-1/8 27.8FNW7008EC0200 2 54.1 3/8-16 4-1/16 102.70 2-15/16 74.65 1-5/8 42.15FNW7008EC0250 2-1/2 66.7 1/2-13 5-3/16 131.37 3-7/8 96.77 2-5/16 57.5FNW7008EC0300 3 79.4 1/2-13 5-5/8 142.47 4 101.52 2-7/16 62.27FNW7008EC0400 4 104.8 1/2-13 6-1/2 166.27 4-7/16 112.37 2-7/8 72.62FNW7008EC0500 5 130.2 1/2-13 9-1/8 231.17 6-1/2 164.42 4-1/2 116.0FNW7008EC0600 6 155.6 5/8-11 11-1/16 281.07 7-15/16 201.32 6 152.9

Catalog Number Pipe Size E F

Bolt SizeDesign Load Weight


FNW7008EC0050 1/2 15.9 2-1/2 63.5 7/16 11.1 1/4-20UNC 150 0.67 0.09FNW7008EC0075 3/4 22.2 2-1/2 63.5 1/2 12.7 1/4-20UNC 250 1.11 0.10FNW7008EC0100 1 28.6 2-1/2 63.5 5/8 15.9 1/4-20UNC 250 1.11 0.13FNW7008EC0125 1-1/4 34.9 2-1/2 63.5 7/8 22.2 1/4-20UNC 250 1.11 0.15FNW7008EC0150 1-1/2 41.3 2-1/2 63.5 1-3/16 30.2 1/4-20UNC 250 1.11 0.18FNW7008EC0200 2 54.1 2-1/2 63.5 1-5/8 41.3 1/4-20UNC 250 1.11 0.21FNW7008EC0250 2-1/2 66.7 2-1/2 63.5 2 50.8 5/16-18UNC 350 1.56 0.51FNW7008EC0300 3 79.4 2-1/2 63.5 2 50.8 5/16-18UNC 350 1.56 0.57FNW7008EC0400 4 104.8 2-1/2 63.5 2 50.8 5/16-18UNC 400 1.78 0.70

FNW7008EC0500 5 130.2 2-1/2 63.5 2 50.8 3/8-16UNC 550 2.45 1.50FNW7008EC0600 6 155.6 3 76.2 2 50.8 3/8-16UNC 500 2.23 1.80

Finish: Epoxy PlatedColor: Copper MSS SP-58, Type 1Federal Speci cation WW-H-171, Type 1


10/32


Hangers

FIGURE 7010 - Adjustable Swivel Ring Hangers

UL Approved - Sizes 1/2 to 8FM Approved - Sizes 3/4 to 8


(Rod size)B C D Design Load Weight

in. mm in. mm in. mm in. mm Lbs. kN Lbs.

FNW7010EP0050 1/2 21.3 3/8-16UNC 2-7/32 56.36 25/32 19.8 7/8 22.2 300 1.33 0.09FNW7010EP0075 3/4 26.6 3/8-16UNC 2-7/16 61.91 1-1/32 26.2 1-3/32 27.8 300 1.33 0.09FNW7010EP0100 1 33.4 3/8-16UNC 2-5/8 66.68 1-7/32 31.0 1-3/16 30.2 300 1.33 0.10FNW7010EP0125 1-1/4 42.1 3/8-16UNC 2-25/32 70.64 1-3/8 34.9 1-5/32 29.4 300 1.33 0.11FNW7010EP0150 1-1/2 48.2 3/8-16UNC 2-7/8 73.03 1-7/16 36.5 1-3/32 27.8 300 1.33 0.12FNW7010EP0200 2 60.3 3/8-16UNC 3-1/32 76.99 1-19/32 40.5 1-1/32 26.2 300 1.33 0.13FNW7010EP0250 2-1/2 73 3/8-16UNC 3-31/32 100.81 2-9/16 65.1 1-23/32 43.7 5 25 4.45 0.29FNW7010EP0300 3 88.9 3/8-16UNC 4-15/32 113.51 3-1/16 77.8 1-15/16 49.2 525 4.45 0.33FNW7010EP0350 3-1/2 101.6 3/8-16UNC 4-15/16 125.41 3-17/32 89.7 2 -1/8 54.0 5 85 4.45 0.37FNW7010EP0400 4 114.3 3/8-16UNC 5-9/32 134.14 3-27/32 97.6 2-3/16 55.6 650 4.89 0.39FNW7010EP0500 5 141.3 1/2-13UNC 5-31/32 151.61 4-7/16 112.7 2-1/4 57.2 1000 4.89 0.53FNW7010EP0600 6 168.2 1/2-13UNC 7 177.80 5-1/2 139.7 2-3/4 69.9 1000 5.56 0.72FNW7010EP0800 8 219 1/2-13UNC 7-31/32 202.41 6-7/16 163.5 2-23/32 69.1 1000 5.56 1.04

A - Rod size (hanger rod not included)B - Center of pipe to top of knured hanger rod nutC - Rod take out (center of pipe to bottom of hanger

rodD - Top of pipe to bottom of hanger rod nut

FIGURE 7012 - Felt Lined Adjustable Swivel Ring Hangers

Finish: Epoxy PlatedColor: ZincMSS SP-58, Type 10Federal Speci cation WW-H-171, Type 10NFPA 13 A - Rod size (hanger rod not included)B - Center of pipe to top of knured hanger rod nut

C - Rod take out (center of pipe to bottom of hangerrod

D - Top of pipe to bottom of hanger rod nut


(Rod size)B C D Design Load Weight

in. mm in. mm in. mm in. mm Lbs. kN Lbs.

FNW7012EP0050 1/2 21.3 3/8-16UNC 2-7/32 56.36 25/32 19.8 7/8 22.2 300 1.33 0.089FNW7012EP0075 3/4 26.6 3/8-16UNC 2-7/16 61.91 1-1/32 26.2 1-3/32 27.8 300 1.33 0.095FNW7012EP0100 1 33.4 3/8-16UNC 2-5/8 66.68 1-7/32 31.0 1-3/16 30.2 300 1.33 0.100FNW7012EP0125 1-1/4 42.1 3/8-16UNC 2-25/32 70.64 1-3/8 34.9 1-5/32 29.4 300 1.33 0.112FNW7012EP0150 1-1/2 48.2 3/8-16UNC 2-7/8 73.03 1-7/16 36.5 1-3/32 27.8 300 1.33 0.121FNW7012EP0200 2 60.3 3/8-16UNC 3-1/32 76.99 1-19/32 40.5 1-1/32 26.2 300 1.33 0.130FNW7012EP0250 2-1/2 73 1/2-13UNC 3-31/32 100.81 2-9/16 65.1 1-23/32 43.7 1000 2.34 0.323FNW7012EP0300 3 88.9 1/2-13UNC 4-15/32 113.51 3-1/16 77.8 1-15/16 49.2 1000 2.34 0.359FNW7012EP0400 4 114.3 5/8-11UNC 5-9/32 134.14 3-27/32 97.6 2-3/16 55.6 1100 2.89 0.474

FNW7012NEP0250* 2-1/2 73 3/8-16UNC 3-31/32 100.81 2-9/16 65.1 1-23/32 43.7 525 2.34 0.323FNW7012NEP0300* 3 88.9 3/8-16UNC 4-15/32 113.51 3-1/16 77.8 1-15/16 49.2 525 2.34 0.359FNW7012NEP0400* 4 114.3 3/8-16UNC 5-9/32 134.14 3-27/32 97.6 2-3/16 55.6 650 2.89 0.474

Finish: Epoxy PlatedColor: Zinc

MSS SP-58, Type 10Federal Speci cation WW-H-171, Type 10NFPA 13

* Note: For 2-1/2 to 4 hangers withNFPA rod sizes,use gure number 7012N

UL Approved - Sizes 1/2 to 4FM Approved - Sizes 3/4 to 4NFPA Rod - Sizes 1/2 to 4 *


11/32


12/32


Hangers

FIGURE 7025 - Adjustable J Hangers

Catalog Number Pipe Size

Bolt SizeA

(Rod Size)

B C

in. mm in. mm in. mm

FNW7025EP0050 1/2 21.3 1/4-20UNC x 2-1/4 3/8-16UNC 1-27/32 46.8 7/8 22.2FNW7025EP0075 3/4 26.7 1/4-20UNC x 2-1/4 3/8-16UNC 2-1/4 57.2 7/8 22.2FNW7025EP0100 1 33.4 1/4-20UNC x 2-1/2 3/8-16UNC 2-7/32 56.4 31/32 24.6FNW7025EP0125 1-1/4 42.2 1/4-20UNC x 2-3/4 3/8-16UNC 2-19/32 65.9 31/32 24.6FNW7025EP0150 1-1/2 48.3 1/4-20UNC x 3 3/8-16UNC 2-7/16 61.9 1-7/32 31.0FNW7025EP0200 2 60.3 1/4-20UNC x 3-1/2 3/8-16UNC 2-21/32 67.5 1-7/32 31.0FNW7025EP0250 2-1/2 73.0 3/8-16UNC x 4-1/2 1/2-13UNC 3-1/16 77.8 1-31/32 50.0FNW7025EP0300 3 88.9 3/8-16UNC x 5 1/2-13UNC 3-9/32 83.3 1-31/32 50.0FNW7025EP0400 4 114.3 3/8-16UNC x 6-1/4 5/8-11UNC 3-25/32 96.0 1-31/32 50.0FNW7025EP0500 5 141.3 3/8-16UNC x 8-1/4 5/8-11UNC 3 1/2 88.9 1-3/16 30.2FNW7025EP0600 6 168.3 3/8-16UNC x 9-3/4 3/4-10UNC 4 5/16 109.5 1-9/16 39.7FNW7025EP0800 8 219.1 3/8-16UNC x 11 3/4-10UNC 4 31/32 126.2 1-31/32 50.0

Catalog Number Pipe Size D E Design Load Weight


FNW7025EP0050 1/2 21.3 1-1/16 27.0 13/32 10.3 400 1.78 0.14FNW7025EP0075 3/4 26.7 1-15/32 37.3 13/32 10.3 400 1.78 0.16FNW7025EP0100 1 33.4 1-7/16 36.5 13/32 10.3 400 1.78 0.18FNW7025EP0125 1-1/4 42.2 1-13/16 46.0 13/32 10.3 400 1.78 0.21FNW7025EP0150 1-1/2 48.3 1-21/32 42.1 13/32 10.3 400 1.78 0.21FNW7025EP0200 2 60.3 1-7/8 47.6 13/32 10.3 400 1.78 0.23FNW7025EP0250 2-1/2 73.0 2-9/32 57.9 9/16 14.3 800 3.56 0.40FNW7025EP0300 3 88.9 2-1/2 63.5 9/16 14.3 800 3.56 0.47FNW7025EP0400 4 114.3 3 76.2 9/16 14.3 800 3.56 0.73FNW7025EP0500 5 141.3 2-17/32 63.9 9/16 14.3 800 3.56 1.15FNW7025EP0600 6 168.3 3-11/32 84.5 9/16 14.3 1000 4.45 2.14FNW7025EP0800 8 219.1 4 101.2 9/16 14.3 1200 5.34 2.71

A - Rod size (hanger rod and nuts not included)B - Center of pipe to top of hanger C - Rod take out (center of pipe to bottom of hanger rod



13/32


Clamps

FIGURE 7020 - Medium Split Horizontal Pipe Clamps

UL Approved - Sizes 3/4 to 8

A - Center of pipe to center of boltB - Center of pipe to end of clamp


Bolt SizeA B

in. mm in. mm in. mm

FNW7020EP0050 1/2 21.3 5/16-18UNC 13/32 10.6 1-1/32 26.2FNW7020EP0075 3/4 26.7 5/16-18UNC 15/32 12.0 1-3/32 27.8FNW7020EP0100 1 33.4 5/16-18UNC 15/32 12.2 1-11/32 34.1FNW7020EP0125 1-1/4 42.2 5/16-18UNC 15/32 12.2 1-7/16 36.5FNW7020EP0150 1-1/2 48.3 5/16-18UNC 15/32 12.2 1-5/8 41.3FNW7020EP0200 2 60.3 1/2-13UNC 21/32 16.4 2-1/8 54.0FNW7020EP0250 2-1/2 73.0 1/2-13UNC 5/8 16.0 2-5/8 66.7FNW7020EP0300 3 88.9 1/2-13UNC 23/32 18.0 3-1/32 77.0FNW7020EP0350 3-1/2 101.6 1/2-13UNC 23/32 18.6 3-1/4 82.6FNW7020EP0400 4 114.3 5/8-11UNC 3/4 19.4 3-9/16 90.5FNW7020EP0500 5 141.3 5/8-11UNC 3/4 19.4 4-19/32 116.7FNW7020EP0600 6 168.3 3/4-10UNC 23/32 18.2 4-15/16 125.4

FNW7020EP0800 8 219.1 3/4-10UNC 15/16 24.0 6-3/16 157.2FNW7020EP1000 10 273.1 7/8-9UNC 1-1/4 32.0 7-19/32 192.9FNW7020EP1200 12 323.9 7/8-9UNC 1-7/16 36.8 8-9/16 217.5

Catalog Number Pipe Size C Design Load Weight

in. mm in. mm Lbs. kN Lbs.

FNW7020EP0050 1/2 21.3 1-17/32 38.9 500 2.2 0.33FNW7020EP0075 3/4 26.7 1-19/32 40.5 500 2.2 0.34FNW7020EP0100 1 33.4 1-7/8 47.6 500 2.2 0.40FNW7020EP0125 1-1/4 42.2 1-15/16 49.2 500 2.2 0.42FNW7020EP0150 1-1/2 48.3 2-1/8 54.0 800 3.6 0.46FNW7020EP0200 2 60.3 2-23/32 69.1 1040 4.6 0.90FNW7020EP0250 2-1/2 73.0 3-1/4 82.6 1040 4.6 1.05FNW7020EP0300 3 88.9 3-21/32 92.9 1040 4.6 1.18FNW7020EP0350 3-1/2 101.6 3-27/32 97.6 1040 4.6 1.25FNW7020EP0400 4 114.3 4-15/32 113.5 1040 4.6 1.91FNW7020EP0500 5 141.3 5-15/32 138.9 1040 4.6 2.29FNW7020EP0600 6 168.3 5-13/16 147.6 1615 7.2 5.30FNW7020EP0800 8 219.1 7-1/16 179.4 1615 7.2 6.36FNW7020EP1000 10 273.1 8-23/32 221.5 2400 10.7 13.53FNW7020EP1200 12 323.9 9-23/32 246.9 2400 10.7 14.93




14/32


FIGURE 7022 - Riser Clamps

UL Approved - Sizes 1/2 to 8

Catalog Number Pipe Size L

Bolt SizeDesign Load Torque

ValueWeight

in. mm in. mm Lbs. kN Lbs.

FNW7022EP0050 1/2 21.3 8-1/2 215.9 3/8-16UNC 220 0.98 25 ft.lbs 0.65FNW7022EP0075 3/4 26.6 9 228.5 3/8-16UNC 220 0.98 25 ft.lbs 0.71FNW7022EP0100 1 33.4 9-1/16 230 3/8-16UNC 220 0.98 25 ft.lbs 0.73FNW7022EP0125 1-1/4 42.1 9-1/2 241.3 3/8-16UNC 250 1.11 25 ft.lbs 0.77FNW7022EP0150 1-1/2 48.2 9-9/10 251.5 3/8-16UNC 250 1.11 25 ft.lbs 0.81FNW7022EP0200 2 60.3 10-3/10 261.6 3/8-16UNC 300 1.33 25 ft.lbs 1.44FNW7022EP0250 2-1/2 73 11-1/16 281 3/8-16UNC 400 1.78 25 ft.lbs 1.56FNW7022EP0300 3 88.9 11-3/4 298.5 3/8-16UNC 500 2.22 25 ft.lbs 1.79FNW7022EP0400 4 114.3 12-15/16 328.6 1/2-13UNC 750 3.33 55 ft.lbs 3.05FNW7022EP0500 5 141.3 14-1/4 362 1/2-13UNC 1500 6.67 55 ft.lbs 3.41FNW7022EP0600 6 168.2 15-1/2 393.7 1/2-13UNC 1600 7.11 55 ft.lbs 4.78FNW7022EP0800 8 219 18-1/4 463.5 5/8-11UNC 2500 11.12 80 ft.lbs 9.23FNW7022EP1000 10 273 20-1/10 510.5 5/8-11UNC 2500 11.12 80 ft.lbs 10.39FNW7022EP1200 12 323.8 22-3/8 568.3 5/8-11UNC 2700 12.01 80 ft.lbs 16.09

FIGURE 7023 - Riser Clamps for Copper Tube

Catalog Number Pipe Size L

Bolt sizeDesign Load Torque

Value

Weight

in. mm in. mm Lbs. kN Lbs.FNW7023EC0050 1/2 15.9 8-1/2 216.5 3/8-16UNC 75 0.33 25 ft.lbs 0.68FNW7023EC0075 3/4 22.2 9-1/4 235.5 3/8-16UNC 75 0.33 25 ft.lbs 0.75FNW7023EC0100 1 28.6 9-5/16 237.0 3/8-16UNC 120 0.53 25 ft.lbs 0.86FNW7023EC0125 1-1/4 34.9 9-1/2 241.0 3/8-16UNC 150 0.67 25 ft.lbs 1.16FNW7023EC0150 1-1/2 41.3 9-5/8 245.0 3/8-16UNC 150 0.67 25 ft.lbs 1.18FNW7023EC0200 2 54.1 10-7/16 265.0 3/8-16UNC 150 0.67 25 ft.lbs 1.30FNW7023EC0250 2-1/2 66.7 11-3/16 284.5 3/8-16UNC 300 1.34 25 ft.lbs 1.38FNW7023EC0300 3 79.4 12 304.0 3/8-16UNC 300 1.34 25 ft.lbs 1.49FNW7023EC0400 4 104.8 12-1/2 318.0 3/8-16UNC 300 1.34 25 ft.lbs 1.61FNW7023EC0600 6 155.6 15-1/8 385.0 1/2-13UNC 600 2.67 55 ft.lbs 5.27



Finish: Epoxy PlatedColor: Copper MSS SP-58, Type 8Federal Speci cation WW-H-171, Type 8

Clamps


15/32


Beam Clamps

FIGURE 7201 - Steel Beam C-Clamp

FIGURE 7202 - MI Beam C-Clamp

Catalog Number A B C D E

FNW7201PC 2.13 0.88 2.38 0.75 0.25

Rod Size Finish Max. Load Wt. (0z.)

3/8-16 Plain 400 Lbs. 5.75

Finish: PlainMSS SP-58, type 23Material: Steel, ASTM A283

Hanger rod not included

Rod Size A B C D Wt. (0z.)

3/8-16 1.75 0.63 1.75 0.75 3.601/2-13 1.75 0.63 1.75 0.75 4.095/8-11 2.00 0.75 2.00 0.75 8.54

Finish: Plain or ZincPer: MSS SP-58, type 23Material: Malleable Iron,

ASTM A47 Grade 32510


Catalog Number Finish Rod Size Max. Load (Lbs.)

FNW7202PC Plain 3/8-16 400FNW7202ZC Zinc 3/8-16 400FNW7202PD Plain 1/2-13 400FNW7202ZD Zinc 1/2-13 400FNW7202PE Plain 5/8-11 440

Note: Do not overtighten the set screw or the clamp can be damaged. The setscrew should be nger tight, then given approximately an additional 1/4 to 1/3turn. The recommended set screw torque is 5 ft-lbs (60 in-lbs).

Beam Clamps

FIGURE 7203 - Jr. Beam Clamp

Rod Size A B C D

3/8-16 1.88 1.22 1.56 0.751/2-13 2.06 1.20 1.63 0.755/8-11 2.19 1.20 1.75 0.753/4-10 2.38 1.20 1.75 0.75

Finish: Plain or ZincMSS SP-58, type 19Material: Malleable Iron,




FNW7203PC Plain 3/8-16 400FNW7203ZC Zinc 3/8-16 400FNW7203PD Plain 1/2-13 500FNW7203ZD Zinc 1/2-13 500FNW7203PE Plain 5/8-11 600FNW7203PF Plain 3/4-10 800

Rod Size E F Wt. (0z.)

3/8-16 0.41 0.88 4.941/2-13 0.44 0.97 6.815/8-11 0.50 1.06 9.173/4-10 0.50 1.06 10.93



16/32


Beam Clamps Beam Clamps

FIGURE 7204 - Wide Mouth Beam Clamp

Finish: PlainPer: MSS SP-58, type 19Material: Malleable Iron,



Rod Size A B C D E Wt. (0z.)

3/8-16 1.63 0.50 1.88 1.25 1.06 7.651/2-13 1.63 0.50 1.88 1.25 1.06 7.655/8-11 2.25 0.75 2.31 1.25 1.38 11.253/4-10 2.38 0.75 2.38 1.25 1.38 14.11


FNW7204PC Plain 3/8-16 400FNW7204PD Plain 1/2-13 500FNW7204PE Plain 5/8-11 850FNW7204PF Plain 3/4-10 900


FIGURE 7806 - Universal Beam Clamp

Catalog Number Rod Size

(RS)Max Load (W1) Max Load (W2)

Lbs. kN Lbs. kN

FNW7806Z 1/4-20 100 0.44 250 1.11

Maximum ange thickness of 5/8

Note: The threaded hole on the back side of the clamp is note load rated.

FIGURE 7868 - Right Angle Clamp

Standard nish is hot dip galvanized


Inch Metric

FNW7868Z0050 1/2 15FNW7868Z0075 3/4 20FNW7868Z0100 1 25

FNW7868Z0150 1-1/2 40FNW7868Z0200 2 50

Finish: ZincMaterial: Malleable Iron Hanger rod not included

FIGURE 7801 - Window Strut to Beam Clamp

FIGURE 7802 - Strut to Beam Spreader Caps

Design load 950 Lbs [4.23 kN] when used in pairsCatalog Number: FNW7801Z

Includes 1 adjustable cap and 1 nonadjustable capCut strut length to opening minus 1 [25mm]

Design load 500 Lbs [2.22 kN] when used as a setCatalog Number: FNW7802Z

1/2" - 13SET SCREW

[41.3]5"1 8

[25.4]1"

W2

[15.9]5"8

[39.7]9"

16

[31.8]

SET SCREWX 11"4

1"4

1

[15.9]5"8

W1

RS

9"32 [7.1]

RS


17/32


Beam Clamp Straps / RollersBeam Clamps

FIGURE 7803 - Square U-Bolt to Beam Clamp

FIGURE 7804 - Square U-Bolt Strut to Beam Clamp

FIGURE 7805 - Notched Type Strut to Beam Clamp

For 2-7/16 & 3-1/4Channel


Material is 1-5/8 [41.3] wide x 1/4 [6.3] thickClamp requires 1/2-13 HCS and 1/2channel nut, order separately


For 13/16 & 1-5/8 ChannelDesign load 1200 Lbs [5.34 kN] when used in pairs

Catalog Number: FNW7803Z

3/8" - 16THREADS

[82.5]1"3 4MAX

3/8" - 16THREADS

[41.3]5"1 8MAX

9/16"

[69.8]3"2 4

[14.2]

FIGURE 7865 - Roller Trolley 4-Bearing Assembly

Stainless steel ball bearingsMax load rating of 600 lbs. [2.67 kN] with 12ga channel

* Based on standard dimensions for channelCatalog Number: FNW7865Z4

2 [54.0]1"8 [33.3]1 5"16* *

[33.3]5"1 16

9/16" [14.3](3 PLACES)

[88.9]1"3 2

[88.9]1"3 2

1613" [20.6]

[28.6]1"1 8

FIGURE 7250 - Beam Clamp Retaining Strap

Typical Installation

Catalog Number W T L

FNW7250Z0600 0.95 16 ga. 8.00FNW7250Z0800 0.95 16 ga. 10.00FNW7250Z1000 0.95 16 ga. 12.00

FNW7250Z1200 0.95 16 ga. 14.00FNW7250Z1400 0.95 16 ga. 16.00

UL Approved

Finish: G90 Galvanized CoatingMaterial: Carbon Steel, ASTM A653 type B


18/32


Pipe SupportsBrackets / Pipe Supports

FIGURE 7811 - Bracket Channel 1-5/8 Channel 2-HL

Catalog Number L Uniform Load*

in. mm Lbs. kN

FNW7811Z1200 12 304.8 570 3.34FNW7811Z1800 18 457.2 500 2.22FNW7811Z2400 24 609.6 350 1.56

* When mounted on 12 gauge channel

FIGURE 7701 - 50# Pipe Support

Catalog Number A B C D E FFNW7701PP 4.00 10.50 4.00 0.8125 1.1875 1.625FNW7701UP 6.00 10.50 4.00 0.8125 1.1875 1.625

Maximum Load: 50 lbs.Height: 4 or 6 inches

Components

Ethafoam 400 plank - The closed-cell medium density blackpolyethylene foam. Ethafoam HS 45 has successfully passedMVSS 302 ammability testing and meets or exceeds therequirements for U.S. Federal Standard PPP-C-1752C, Type III.Ethafoam is a registered trademark of Sealed Air Corporation (US).

14 Gauge Strut Channel - Cold roll-formed carbon steel conformsto ASTM 570 GR 33 and ASTM A653.

Bondmaster Instaweld 34-3378 - Adhesive conforms toMS-CC926.

FIGURE 7715 & 7730 - 150# & 300# Pipe Support

Catalog Number A B C D E F

FNW7715 4.00 12.00 12.00 1.01 5.16 1.63FNW7730 4.00 21.50 12.00 1.01 5.16 1.63

Maximum Load: 150 lbs. (Fig. 7715)300 lbs. (Figure 7730)

Height: 4 inchesComponents

Ethafoam 400 plank - The closed-cell medium density blackpolyethylene foam. Ethafoam HS 45 has successfully passedMVSS 302 ammability testing and meets or exceeds therequirements for U.S. Federal Standard PPP-C-1752C, Type III.Ethafoam is a registered trademark of Sealed Air Corporation (US).

14 Gauge Strut Channel - Cold roll-formed carbon steel conformsto ASTM 570 GR 33 and ASTM A653.

14 Gauge Galva Neal Sheet Metal - Hot-dipped zinc coatedtreated to a harder surface than galvanizing alone.

Bondmaster Instaweld 34-3378 - Adhesive conforms toMS-CC926.

FIGURE ELKITC - Elevation Kit for Pipe Supports

1-1/4 Schedule 40 Steel Pipe by Others

ELKIITC Provides elevation to pipe support systems. Kit containscomponents for two posts using 1-1/4 schedule 40 steel pipesupplied by others. Minimum elevation is 6, or 10 when mountedon gure 7715 or 7730 pipe supports (sold separately) usingincluded channel nuts. Kit components include:

2 Base Units 2 Vertical Mounts 10 1/2-13 x 3/4 Hex Bolts

6 1/2 Washers 4 1/2 Strut Nuts 2 1/2 Hex Nuts

Catalog Number

FNWELKITC

L

5" [117.5]4 8

[50.8]2" 9/16 [14.3]2 Places


19/32


20/32


Angle FittingsEnd Caps

FIGURE 7830 - PVC Channel End Cap (1/5/8)

FIGURE 7831 - Channel End Cap (1-5/8)

FIGURE 7840 - No Twist 2-Hole Corner Angle Fitting

FIGURE 7841 - Corner Angle Fitting

White PVCCatalog Number: FNW7830W0162

Catalog Number: FNW7840Z2


End Cap 1-5/8 12 Ga.Catalog Number: FNW7831Z0162



5" CHANNEL [41.3]1 8 [54.0]2 1"8

1"2 [54.0]8

9/16 [14.3]2 Places

[50.8]2"

[47.6]1 7"8

9/16 [14.3]2 Places

7" [47.6]1 8

7"3 [98.4]8 9/16 [14.3]3 Places

7" [98.4]3 8

3 [95.2]3"4

9/16 [14.3]4 Places


21/32


Angle FittingsAngle Fittings

FIGURE 7842 - Cross Corner Angle Fitting

FIGURE 7843 - 3-Way Cross Corner Angle Fitting

FIGURE 7844 - 7-Hole Gusset Angle Fitting

FIGURE 7845 - 2-Hole Open 45 Corner Angle Fitting

FIGURE 7846 - 2-Hole Closed 45 Corner Angle

2-Hole Catalog Number: FNW7842Z2 FNW7842G2

3-Hole Catalog Number: FNW7842Z3






[57.1]2

1"

4

1 5" [41.3]8 9/16 [14.3]

2 Places

81"4 [104.8]

1 8 [41.3]5" 9/16 [14.3]

3 Places

1" [88.9]3 2

2 4 [57.1]1"

9/16 [14.3]3 Places

1"3 [88.9]2

[104.8]1"84

9/16 [14.3]4 Places

A

[63.5]21"2

1"23 [88.9]

9/16 [14.3]2 Places

A

[54.0]81"2

[88.9]3 1"2

81 [28.6]1"

9/16 [14.3]2 Places

4 [104.8]

8

1"

[104.8]81"4

1" ALL HOLES [31.8]1 4CENTER TO CENTER

9/16 [14.3]7 Places


22/32


Flat FittingsAngle Fittings

FIGURE 7847 - 4-Hole Open 45 Corner Angle Fitting

FIGURE 7848 - 2-Hole Angle Brace

FIGURE 7835 - Square Washer Flat Fitting

FIGURE 7836 - Notched Square Washer Flat Fitting




Catalog Number Bolt Size Hole Size

in. mm in. mm

FNW7835Z0037FNW7835G0037 3/8 8 7/16 11.1

FNW7835Z0050FNW7835G0050 1/2 12 9/16 14.3

FNW7835Z0062FNW7835G0062 5/8 16 11/16 17.5

FNW7835Z0075 3/4 20 13/16 20.6

Catalog Number Bolt Size

in. mm

FNW7836Z0037FNW7836G0037 3/8 8

FNW7836Z0050 1/2 12

A

[93.7]

2 [88.9]31"

1611"3

9/16 [14.3]4 Places

[41.3]1 5"8

[304.8]12" [263.5]3"10 8

1 85" [41.3]

8 [263.5]103"

9/16 [14.3]2 Places

[41.3]1 5"8

[457.2]18" [371.5]5"14 8

1 85" [41.3]

[371.5]8145"

9/16 [14.3]2 Places

[41.3]5"81

9/16 [14.3]

[41.3]1 85"

9/16 [14.3]


23/32


Flat FittingsFlat Fittings

FIGURE 7837 - Splice Plate Flat Fitting

FIGURE 7838 - 3-Hole Corner Plate Flat Fitting

FIGURE 7839 - 4-Hole Tee Plate Flat Fitting




Catalog Number: FNW7838Z3 FNW7838G3

Catalog Number: FNW7839Z4 FNW7839G4

[88.9]1"23

9/16 [14.3]2 Places

[136.5]3"85

9/16 [14.3]3 Places

[184.1]1"47

9/16 [14.3]4 Places

2 [88.9]31"

1"2 [88.9]3

9/16 [14.3]3 Places

[88.9]21"3

[136.5]5 83"

9/16 [14.3]4 Places


24/32


Post BasePost Base

FIGURE 7850 - Single Channel 2-Hole Base

FIGURE 7851 - Single Channel 2-Hole Flush Base

FIGURE 7852 - Single Channel 4-Hole Standard

FIGURE 7853 - Single Channel 4-Hole Base (tall)

Square Mounted 3-1/2Catalog Number: FNW7850Z


FNW7853G

Square Mounted Flush 3-1/2Catalog Number: FNW7851Z



[152.4]6"4" [101.6]

[25.4]1"

1"3 2 [88.9]

[19.0]43"

2 PLACES

9/16 [14.3]6 Places

4" [101.6]

[25.4]1"

1"3 2 [88.9] [19.0]43"

2 PLACES

[152.4]6"

9/16 [14.3]6 Places

[88.9]3 21"

6" [152.4]

1"

4 [108.0]

6" [152.4]4

[108.0]

43"

4 PLACES

3"

4 PLACES4

441"

[19.0] [19.0]

9/16 [14.3]6 Places

41"

6"

4

[152.4]

[108.0]

4 PLACES [19.0]3" 4

[108.0]

6" [152.4]

1"44

[41.3] [41.3]11 885"5"

9/16 [14.3]3 Places

FIGURE 7855 - Single Channel 4-Hole Base (short)

[19.0]43"

4 PLACES

[152.4]6" [152.4]6"

[88.9]3 21"

[108.0]1"441"4 [108.0]4

9/16 [14.3]6 Places


25/32


Strut ClampsStrut Clamps

FIGURE 7815 - Cushioned Pipe Strut Clamp FIGURE 7816 - Cushioned Tubing Strut Clamp

Catalog Number Pipe Size O.D. Design Load

in. Metric in. mm Lbs. kN

FNW7815Y0050 1/2 15 0.840 21.3 330 1.48FNW7815Y0075 3/4 20 1.050 26.7 330 1.48FNW7815Y0100 1 25 1.315 33.4 330 1.48FNW7815Y0125 1-1/4 32 1.660 42.2 730 3.26FNW7815Y0150 1-1/2 40 1.900 48.3 730 3.26FNW7815Y0200 2 50 2.375 60.3 730 3.26FNW7815Y0250 2-1/2 65 2.875 73.0 730 3.26FNW7815Y0300 3 80 3.500 88.9 1200 5.34FNW7815Y0400 4 100 4.500 114.3 1200 5.34

Catalog Number Tubing O.D. Design Load

in.(Fractions)

in.(Decimal)

mm Lbs. kN

FNW7816Y0025 1/4 0.250 6.4 330 1.48FNW7816Y0037FNW7816S0037 3/8 0.375 9.5 330 1.48

FNW7816Y0050FNW7816S0050 1/2 0.500 12.7 330 1.48

FNW7816Y0062 5/8 0.625 15.9 330 1.48FNW7816Y0075 3/4 0.750 19.0 330 1.48FNW7816Y0087FNW7816S0087 7/8 0.875 22.3 330 1.48

FNW7816Y0100 1 1.000 25.4 330 1.48FNW7816Y0112 1-1/8 1.125 28.6 330 1.4FNW7816Y0125 1-1/4 1.250 31.8 330 1.4FNW7816Y0137 1-3/8 1.375 34.9 330 1.4FNW7816Y0150 1-1/2 1.500 38.1 730 3.2FNW7816Y0162 1-5/8 1.625 41.3 730 3.2

FNW7816Y0187 1-7/8 1.875 47.6 730 3.2FNW7816Y0200 2 2.000 50.8 730 3.26FNW7816Y0212 2-1/8 2.125 54.0 730 3.2FNW7816Y0262 2-5/8 2.625 66.7 730 3.2FNW7816Y0312 3-1/8 3.125 79.4 730 3.2FNW7816Y0362 3-5/8 3.625 92.1 1200 5.34FNW7816Y0412 4-1/8 4.125 104.8 1200 5.3

Cushion InformationMaterial: Thermoplastic Elastomer Temperature Range: -50F to 275FHardness Shore D: 46.0 avg. (per ASTM D-2240)Dielectric Strength: 640 volts/mil.

Cushion InformationMaterial: Thermoplastic Elastomer Temperature Range: -50F to 275FHardness Shore D: 46.0 avg. (per ASTM D-2240)Dielectric Strength: 640 volts/mil.

DESIGN LOADDESIGN LOAD


26/32


DESIGN LOAD DESIGN LOAD


FIGURE 7870 - Copper Tubing Strut Clamp FIGURE 7871 - EMT Strut Clamp

Standard nish for gure 7870 is Copper Zinc Dichromate which has acopper color to identify product for use with copper tubing.

Catalog Number Tubing Sizes O.D. Design Load


FNW7870C0025 1/4 6 0.375 9.5 400 1.78FNW7870C0037 3/8 10 0.500 12.7 400 1.78FNW7870C0050 1/2 15 0.625 15.9 400 1.78FNW7870C0075 3/4 20 0.875 22.2 400 1.78FNW7870C0100 1 25 1.125 28.6 600 2.67FNW7870C0125 1-1/4 32 1.375 34.9 600 2.67FNW7870C0150 1-1/2 40 1.625 41.3 600 2.67FNW7870C0200 2 50 2.125 54.0 800 3.56FNW7870C0250 2-1/2 65 2.625 66.7 800 3.56FNW7870C0300 3 80 3.125 79.4 800 3.56FNW7870C0350 3-1/2 90 3.625 92.1 1000 4.45FNW7870C0400 4 100 4.125 104.8 1000 4.45

FNW7870C0500 5 125 5.125 130.2 1000 4.45FNW7870C0600 6 150 6.125 155.6 1000 4.45

Catalog Number EMT Sizes O.D. Design Load


FNW7871Z0050 1/2 15 0.706 17.9 400 1.78FNW7871Z0075 3/4 20 0.922 23.4 400 1.78FNW7871Z0125 1-1/4 32 1.510 38.4 600 2.67

FNW7871Z0150 1-1/2 40 1.740 44.2 800 3.56FNW7871Z0200 2 50 2.197 55.8 800 3.56


27/32


DESIGN LOAD


FIGURE 7872 - O.D. Strut Clamp FIGURE 7872 - O.D. Strut Clamp (continued)

Catalog Number

Size (O.D.) Design Load

in.(Fractions)

in.(Decimal)

mm Lbs. kN

FNW7872Z0025 1/4 0.250 6.4 400 1.78

FNW7872Z0037 3/8 0.375 9.5 400 1.78FNW7872Z0050 1/2 0.500 12.7 400 1.78

FNW7872Z0062 5/8 0.625 15.9 400 1.78

FNW7872Z0075 3/4 0.750 19.0 400 1.78

FNW7872Z0087 7/8 0.875 22.3 400 1.78

FNW7872Z0100 1 1.000 25.4 600 2.67

FNW7872Z0112 1-1/8 1.125 28.6 600 2.67

FNW7872Z0125 1-1/4 1.250 31.8 600 2.67

FNW7872Z0137 1-3/8 1.375 34.9 600 2.67

FNW7872Z0150 1-1/2 1.500 38.1 600 2.67

FNW7872Z0162 1-5/8 1.625 41.3 600 2.67

FNW7872Z0175 1-3/4 1.750 44.5 800 3.56

FNW7872Z0187 1-7/8 1.875 47.6 800 3.56

FNW7872Z0200 2 2.000 50.8 800 3.56

FNW7872Z0212 2-1/8 2.125 54.0 800 3.56

FNW7872Z0225 2-1/4 2.250 57.2 800 3.56

FNW7872Z0237 2-3/8 2.375 60.3 800 3.56

FNW7872Z0250 2-1/2 2.500 63.5 800 3.56

FNW7872Z0262 2-5/8 2.625 66.7 800 3.56

FNW7872Z0275 2-3/4 2.750 69.9 800 3.56

FNW7872Z0287 2-7/8 2.875 73.0 800 3.56

FNW7872Z0300 3 3.000 76.2 800 3.56

FNW7872Z0312 3-1/8 3.125 79.4 800 3.56

FNW7872Z0325 3-1/4 3.250 82.6 800 3.56

FNW7872Z0337 3-3/8 3.375 85.7 800 3.56

FNW7872Z0350 3-1/2 3.500 88.9 800 3.56

Catalog Number

Size (O.D.) Design Load

in.(Fractions)

in.(Decimal)

mm Lbs. kN

FNW7872Z0362 3-5/8 3.625 92.1 800 3.56

FNW7872Z0375 3-3/4 3.750 95.3 1000 4.45

FNW7872Z0387 3-7/8 3.875 98.4 1000 4.45

FNW7872Z0400 4 4.000 101.6 1000 4.45

FNW7872Z0412 4-1/8 4.125 104.8 1000 4.45

FNW7872Z0425 4-1/4 4.250 108.0 1000 4.45

FNW7872Z0437 4-3/8 4.375 111.1 1000 4.45

FNW7872Z0450 4-1/2 4.500 114.3 1000 4.45

FNW7872Z0462 4-5/8 4.625 117.5 1000 4.45

FNW7872Z0475 4-3/4 4.750 120.7 1000 4.45

FNW7872Z0487 4-7/8 4.875 123.8 1000 4.45FNW7872Z0500 5 5.000 127.0 1000 4.45

FNW7872Z0512 5-1/8 5.125 130.2 1000 4.45

FNW7872Z0525 5-1/4 5.250 133.4 1000 4.45

FNW7872Z0537 5-3/8 5.375 136.5 1000 4.45

FNW7872Z0550 5-1/2 5.500 139.7 1000 4.45

FNW7872Z0562 5-5/8 5.625 142.9 1000 4.45

FNW7872Z0587 5-7/8 5.875 149.2 1000 4.45

FNW7872Z0600 6 6.000 152.4 1000 4.45

FNW7872Z0612 6-1/8 6.125 155.6 1000 4.45FNW7872Z0637 6-3/8 6.375 161.9 1000 4.45

FNW7872Z0650 6-1/2 6.500 165.1 1000 4.45

FNW7872Z0662 6-5/8 6.625 168.3 1000 4.45

FNW7872Z0675 6-3/4 6.750 171.5 1000 4.45

FNW7872Z0750 7-1/2 7.500 190.5 1000 4.45

FNW7872Z0762 7-5/8 7.625 193.7 1000 4.45

FNW7872Z0775 7-3/4 7.750 196.9 1000 4.45

FNW7872Z0800 8 8.000 203.2 1000 4.45

FNW7872Z0837 8-3/8 8.375 212.7 1000 4.45

FNW7872Z0850 8-1/2 8.500 215.9 1000 4.45


28/32


DESIGN LOAD DESIGN LOAD


FIGURE 7873 - Rigid Strut Clamp FIGURE 7874 - Universal Strut Clamp

Catalog Number Pipe Sizes O.D. Design Load


FNW7873Z0037 3/8 10 0.675 17.1 400 1.78

FNW7873Z0050FNW7873S0050 1/2 15 0.840 21.3 400 1.78

FNW7873Z0075FNW7873S0075 3/4 20 1.050 26.7 600 2.67

FNW7873Z0100FNW7873S0100 1 25 1.315 33.4 600 2.67

FNW7873Z0125FNW7873S0125 1-1/4 32 1.660 42.2 600 2.67

FNW7873Z0150FNW7873S0150 1-1/2 40 1.900 48.3 800 3.56

FNW7873Z0200FNW7873S0200 2 50 2.375 60.3 800 3.56

FNW7873Z0250FNW7873S0250 2-1/2 65 2.875 73.0 800 3.56

FNW7873Z0300FNW7873S0300 3 80 3.500 88.9 800 3.56

FNW7873Z0350 3-1/2 90 4.000 101.6 1000 4.45

FNW7873Z0400 4 100 4.500 114.3 1000 4.45

FNW7873Z0500 5 125 5.562 141.3 1000 4.45

FNW7873Z0600 6 150 6.625 168.3 1000 4.45

FNW7873Z0800 8 200 8.625 219.1 1000 4.45

FNW7873Z1000 10 250 10.750 273.1 1000 4.45

FNW7873Z1200 12 300 12.750 323.9 1000 4.45

Catalog Number Clamp Sizes* O.D. Design Load


FNW7874Z0050 1/2 15 0.773 19.6 400 1.78

FNW7874Z0075 3/4 20 0.986 25.0 600 2.67FNW7874Z0100 1 25 1.239 31.5 600 2.67

FNW7874Z0125 1-1/4 32 1.585 40.3 600 2.67

FNW7874Z0150 1-1/2 40 1.820 45.7 800 3.56

FNW7874Z0200 2 50 2.286 58.1 800 3.56

* These clamps are designed to t both pipe (rigid conduit) and thin walledtubing (EMT) in the corresponding sizes.


29/32


30/32


FIGURE 7501 - Beam Connector

Finish: PlainPer: MSS SP-58, type 34Material: Malleable Iron,



Catalog Number Rod Size A B

FNW7501PC 3/8-16 2.19 0.56

Rod Size Finish Max. Load Wt. (0z.)

3/8-16 Plain 250 Lbs. 1.80

FIGURE 7502 - Beam Ceiling Flange

Finish: Plain, Zinc, or Copper Material: Malleable Iron,



Rod Size A B C D

3/8-16 2.75 2.00 1.38 0.501/2-13 2.75 2.00 1.38 0.50


FNW7502PC Plain 3/8-16 180FNW7502ZC Zinc 3/8-16 180FNW7502CC Copper 3/8-16 180FNW7502PD Plain 1/2-13 180FNW7502ZD Zinc 1/2-13 180FNW7502CD Copper 1/2-13 180

Rod Size E F Wt. (0z.)

3/8-16 0.25 0.31 2.961/2-13 0.25 0.31 2.72

Conduit/Pipe ClampsAttachments

FIGURE 7310 - Rigid/EMT Clamp

FIGURE 7311 - Copper Pipe Clamp

Catalog Number Sizes (in.)

A B GaugeDesignLoadRigid EMT

FNW7310Z0050 3/81/2 1/2 0.80 0.28 18 200 lbs.

FNW7310Z0075 3/4 3/4 1.00 0.28 18 200 lbs.FNW7310Z0100 1 1 1.20 0.28 18 200 lbs.

FNW7310Z0125E 1-1/4 1.50 0.28 18 200 lbs.FNW7310Z0125 1-1/4 1-1/2 1.70 0.28 18 200 lbs.FNW7310Z0150 1-1/2 1.87 0.34 18 200 lbs.FNW7310Z0200 2 2 2.25 0.34 18 350 lbs.FNW7310Z0250 2-1/2 2-1/2 3.00 0.41 14 350 lbs.FNW7310Z0300 3 3 3.50 0.41 14 350 lbs.

Finish: ZincMaterial: Steel

Notes:1. Sizes 0050 to 0200 have embossed threading for clamp screw.2. Sizes 0250 & 0300 use nut and bolt.3. Sizes 0250 & 0300 have an embossment around hole B.

Finish: Copper Material: Steel

Notes:1. Copper plating is for identi cation purposes only.2. All sizes use nut and bolt.3. All sizes have an embossment around hole B.

Catalog Number Copper

Sizes (in.) A B Gauge Design Load

FNW7311C0050 1/2 0.65 0.28 19 200 lbs.FNW7311C0075 3/4 0.87 0.28 18 200 lbs.FNW7311C0100 1 1.20 0.28 18 200 lbs.FNW7311C0125 1-1/4 1.38 0.28 18 200 lbs.FNW7311C0150 1-1/2 1.70 0.34 16 200 lbs.FNW7311C0200 2 2.13 0.34 16 200 lbs.


31/32


Shields

FIGURE 7750 (Standard) & 7751 (Domestic) - MSS Compliant Insulation Protection Shields

Catalog Number ShieldSize

L I.D. T RequiredHanger Size

Weight

Standard Domestic in. mm in. mm in. mm gauge Lbs.

FNW7750Z0150 FNW7751Z0150 1-1/2 12 305 1.91 48.4 0.047 1.2 18 1-1/2 0.FNW7750Z0200 FNW7751Z0200 2 12 305 2.38 60.4 0.047 1.2 18 2 0.5FNW7750Z0250 FNW7751Z0250 2-1/2 12 305 2.88 73.2 0.047 1.2 18 2-1/2 0.FNW7750Z0300 FNW7751Z0300 3 12 305 3.50 88.9 0.047 1.2 18 3 0.8FNW7750Z0350 FNW7751Z0350 3-1/2 12 305 4.00 101.6 0.047 1.2 18 3-1/2 0.FNW7750Z0400 FNW7751Z0400 4 12 305 4.52 114.7 0.047 1.2 18 4 1.FNW7750Z0450 FNW7751Z0450 4-1/2 12 305 5.00 127.0 0.047 1.2 18 5 1.FNW7750Z0500 FNW7751Z0500 5 12 305 5.31 135.0 0.047 1.2 18 5 1.3FNW7750Z0550 FNW7751Z0550 5-1/2 12 305 5.56 141.2 0.047 1.2 18 5 1.FNW7750Z0600 FNW7751Z0600 6 12 305 6.66 169.1 0.059 1.5 16 6 2.0FNW7750Z0700 FNW7751Z0700 7 12 305 7.65 194.3 0.059 1.5 16 8 2.3FNW7750Z0800 FNW7751Z0800 8 12 305 8.70 220.9 0.059 1.5 16 8 2.7FNW7750Z1000 FNW7751Z1000 10 18 458 10.86 275.8 0.059 1.5 16 10 5.FNW7750Z1200 FNW7751Z1200 12 24 610 12.83 326.0 0.071 1.8 15 12 9.

Finish: G60 Galvanized CoatingMaterial: Steel, ASTM 1011 type BMSS SP-58, Type 40*Federal Speci cation WW-H-171, Type 41*

* Complies when used within the pipe size, insulationthickness, and compressive strength of insulation asspeci ed by MSS SP-58.

Domestic shields are ordered on demand (SOD)

FIGURE 7753 - Light Duty Insulation Protection Shields

Material: Carbon Steel, ASTM A653, type A/BFinish: G60 Galvanized Coating

Catalog Number L I.D. T Required

Hanger SizeWeight

in. mm in. mm in (mm) in. mm gauge Lbs.FNW7753Z0000 11.9 302 1.90 48.3 0.093 (2.38) 0.024 0.6 24 1-1/2 0.25FNW7753Z0001 11.9 302 2.38 60.5 0.093 (2.38) 0.024 0.6 24 2 0.31

FNW7753Z0002 11.9 302 2.87 72.9 0.093 (2.38) 0.024 0.6 24 2-1/2 0.38FNW7753Z0003 12 305 3.50 88.9 0.093 (2.38) 0.047 1.2 18 3 0.88FNW7753Z0004 12 305 4.00 101.6 0.093 (2.38) 0.047 1.2 18 3-1/2 1.01FNW7753Z0005 12 305 4.50 114.3 0.093 (2.38) 0.047 1.2 18 4 1.13FNW7753Z0006 12 305 5.00 127.0 0.125 (3.18) 0.047 1.2 18 5 1.26FNW7753Z0007 12 305 5.63 143.0 0.125 (3.18) 0.047 1.2 18 5 1.40FNW7753Z0008 12 305 6.62 168.1 0.125 (3.18) 0.047 1.2 18 6 1.66FNW7753Z0009 12 305 7.63 193.8 0.250 (6.35) 0.047 1.2 18 8 1.91FNW7753Z0010 12 305 8.62 219.0 0.250 (6.35) 0.047 1.2 18 8 2.16FNW7753Z0013 12 305 9.63 244.6 0.250 (6.35) 0.047 1.2 18 10 2.41FNW7753Z0014 12 305 10.75 273.0 0.250 (6.35) 0.047 1.2 18 10 2.69FNW7753Z0015 12 305 11.75 298.5 0.250 (6.35) 0.047 1.2 18 12 2.94FNW7753Z0016 12 305 12.75 323.9 0.250 (6.35) 0.047 1.2 18 12 3.19


32/32

DOC: FNWhangers Ver. 3/2012

2012 - FNW. All rights reserved.The FNW logo is a trademark of Ferguson Enterprises, Inc., PL Sourcing, PO Box 2778, Newport News, VA 23609

PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES

Your Piping Products SourceSince FNW was established in 1979, it has been dedicated to providing qualityproducts for industrial and commercial applications. With a basic philosophy toprovide a product suited to the needs of the end user, FNW has built a productoffering with an innovative approach to the market and has continued to grow itsproduct range to meet those needs. We continue to add products that may not bere ected in this catalog. Therefore, please visit our web site at www.fnw.com forupdates and the latest additions to our product offerings.

For technical assistance, contact:4120 NE Columbia Blvd, Portland, OR 97211

Phone (503) 287-8383, Fax (503) 281-9677

Your Local Distributor/Representative Is:

Fn w 104 Hanger Brochure

Documents

Transcript of Fn w 104 Hanger Brochure