FM Stereo FM-AM Receiver - Sony · FM Stereo FM-AM Receiver 4-238-379-12(1) STR-DE685 Owner’s...

FM StereoFM-AM Receiver

4-238-379-12(1)

STR-DE685

Owner’s RecordThe model and serial numbers are located on the rear panel. Record the serial numberin the space provided below. Refer to them whenever you call upon your Sony dealerregarding this product.

Model No. STR-DE685 Serial No.

© 2002 Sony Corporation

GBOperating Instructions

2GB

WARNING

To prevent fire or shock hazard, do notexpose the unit to rain or moisture.

To prevent fire, do not cover the ventilation of theapparatus with newspapers, table-cloths, curtains,etc. And don’t place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objectsfilled with liquids, such as vases, on the apparatus.

Don’t throw away the battery withgeneral house waste, dispose of itcorrectly as chemical waste.

Do not install the appliance in a confined space, suchas a bookcase or built-in cabinet.

For customers in the United States

This symbol is intended to alert theuser to the presence of uninsulated“dangerous voltage” within theproduct’s enclosure that may be ofsufficient magnitude to constitute arisk of electric shock to persons.

This symbol is intended to alert theuser to the presence of importantoperating and maintenance (servicing)instructions in the literatureaccompanying the appliance.

WARNINGThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection againstharmful interference in a residential installation. Thisequipment generates, uses, and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, thereis no guarantee that interference will not occur in aparticular installation. If this equipment does causeharmful interference to radio or television reception,which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct theinterference by one or more of the followingmeasures:

– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and

receiver.– Connect the equipment into an outlet on a circuit

different from that to which the receiver isconnected.

– Consult the dealer or an experienced radio/TVtechnician for help.

CAUTIONYou are cautioned that any changes or modificationnot expressly approved in this manual could voidyour authority to operate this equipment.

Note to CATV system installer:This reminder is provided to call CATV systeminstaller’s attention to Article 820-40 of the NEC thatprovides guidelines for proper grounding and, inparticular, specifies that the cable ground shall beconnected to the grounding system of the building, asclose to the point of cable entry as practical.

For customers in Canada

CAUTIONTO PREVENT ELECTRIC SHOCK, DO NOT USETHIS POLARIZED AC PLUG WITH ANEXTENSION CORD, RECEPTACLE OR OTHEROUTLET UNLESS THE BLADES CAN BE FULLYINSERTED TO PREVENT BLADE EXPOSURE.

ENERGY STAR® is a U.S. registeredmark.As an ENERGY STAR® partner, SonyCorporation has determined that thisproduct meets the ENERGY STAR®

guidelines for energy efficiency.

This receiver incorporates Dolby* Digital and ProLogic Surround and the DTS** Digital SurroundSystem.* Manufactured under license from Dolby

Laboratories.“Dolby”, “Pro Logic” and the double-D symbol aretrademarks of Dolby Laboratories.

** “DTS” and “DTS Digital Surround” are registeredtrademarks of Digital Theater Systems, Inc.

3GB

Table of Contents

GB

List of Button Locations andReference Pages

Main unit ............................................... 5

Hooking Up the Components

Required cords ....................................... 6Antenna hookups ................................... 7Audio component hookups .................... 8Video component hookups .................... 9Digital component hookups ................. 10Multi channel input hookups ............... 12Other hookups ..................................... 13

Hooking Up and Setting Upthe Speaker System

Speaker system hookups ..................... 15Performing initial setup operations ..... 17Multi channel surround setup .............. 17Checking the connections .................... 22

Basic Operations

Selecting the component ..................... 23Changing the display ........................... 24

Enjoying Surround Sound

Automatically decoding the inputaudio signal ................................... 25

Selecting a sound field ........................ 25Using only the front speakers

(2 Channel Stereo) ......................... 27Enjoying stereo sound in multi channel

(Dolby Pro Logic ) ..................... 27Understanding the multi channel

surround displays .......................... 28Customizing sound fields .................... 29

Receiving Broadcasts

Storing FM stations automatically(AUTOBETICAL)1) ...................... 32

Direct tuning ........................................ 32Automatic tuning ................................. 33Preset tuning ........................................ 33Using the Radio Data System (RDS)1) .... 35

Other OperationsNaming preset stations and program

sources ........................................... 37Recording ............................................ 37Using the Sleep Timer ......................... 38Adjustments using the

SET UP button .............................. 38CONTROL A1 control system ......... 39

Operations Using the RemoteRM-PP4112)

Before you use your remote ................ 42Remote button description ................... 42Selecting the mode of the remote ........ 45Programming the remote ..................... 46

Operations Using the RemoteRM-U305C3)

Before you use your remote ................ 49Remote button description ................... 49Changing the factory setting of

a function button ........................... 52

Additional InformationPrecautions .......................................... 53Troubleshooting ................................... 53Specifications ...................................... 56Tables of settings using SURR, LEVEL,

EQ, and SET UP buttons ............... 59Adjustable parameters for each

sound field ........................ Back page

1) Models of area code CEL, CEK only.2) Models of area code U, CA only.3) Except for models of area code U, CA.

4GB

4-XXX-XXX-XX AA

VIDEO SPEAKERS IMPEDANCE USE 8 – 16Ω

Y

PB B-Y

PR R-Y

NITOROUT

R L

EAKERS IMPEDANCE USE 8 – 16Ω

FRONT ACENTER

AC OUTLET

FRONT B

R L

R L

Area code

About This ManualThe instructions in this manual are for modelSTR-DE685. Check your model number by looking atthe lower right corner of the front panel.

About area codesThe area code of the receiver you purchased isshown on the lower portion of the rear panel (seethe illustration below).

Any differences in operation, according to thearea code, are clearly indicated in the text, forexample, “Models of area code AA only”.

TipThe instructions in this manual describe the controlson the receiver. You can also use the controls on thesupplied remote if they have the same or similarnames as those on the receiver. For details on the useof your remote, see• pages 42–48 for RM–PP411 (models of area code

U, CA only).• pages 49–52 for RM–U305C (except for models of

area code U, CA)

Note for the supplied remote

For RM-PP411 (Models of area codeU, CA only)The TV/SAT, PHONO, SOURCE, MPX/DUAL, ANALOG DIRECT, 12 andON SCREEN buttons on the remote are notavailable.

For RM-U305C (Except for models ofarea code U, CA)The TV/SAT and PHONO buttons on theremote are not available.

Demonstration ModeThe demonstration will activate the first time youturn on the power. When the demonstration starts,the following message appears in the display:

“NOW DEMONSTRATION MODE IFYOU FINISH DEMONSTRATIONPLEASE PRESS POWER KEY WHILETHIS MESSAGE APPEARS IN THEDISPLAY THANK YOU”

To cancel the demonstrationPress ?/1 to turn the receiver off while the abovemessage is being displayed. The next time youturn the receiver on, the demonstration will notappear.

To view the demonstrationHold down SET UP and press ?/1 to turn on thepower.

Notes• Running the demonstration will clear the

receiver’s memory. For details on what will becleared, see “Clearing the receiver's memory”on page 17.

• There will be no sound when the demonstrationmode is activated.

• You cannot cancel demonstration if you did notpress ?/1 while the above message is beingdisplayed. To cancel demonstration after theabove message appears, press ?/1 twice toactivate the demonstration again. Then, press?/1 while the above message is beingdisplayed.

5GB

List o

f Bu

tton

Lo

ca

tion

s an

d R

efe

ren

ce

Pa

ge

s

wkwle;eaesedejekelr;rars eh efeg

123 5 906 qa qsqdqfqg qj qk ql w; ws wf whwa wd wg wj

qh74 8

List of Button Locations and Reference Pages

Main unitFM/AM (Models of area code

CEL, CEK only) ej (32, 33)FM MODE (Models of area code

CEL, CEK only) ek , (Exceptfor models of area code CEL,CEK) el (33)

INPUT MODE ql (23)IR (receptor) 6 (42, 49, 55)Jog dial eh (18, 29, 31, 37, 38)

L – OLEVEL qs (18, 22, 29, 59)MASTER VOLUME wk (22, 53)MD/TAPE wa (23)MEMORY ra (32, 34)MODE es (26, 31, 54)MULTI CHANNEL DECODING

(indicator) qa (23)MULTI CH IN e; (23)MUTING wl (24, 53)NAME qf (37)

P – SPHONES (jack) 3 (24, 54)PRESET/PTY SELECT +/–

(Models of area code CEL, CEKonly) 7 (34, 35)

PRESET TUNING +/– (Exceptfor models of area code CEL,CEK) 7 (34, 57)

PTY (Models of area code CEL,CEK only) el (35)

SET UP qd (4, 18, 38, 59)SHIFT r; (34)SPEAKERS A/B 2 (24, 29, 53)SURR 0 (29, 59)

T – ZTUNER wg (23, 33, 34, 37)TUNING +/– 8 (33)VIDEO 1 w; (23)VIDEO 2 ws (23)VIDEO 3 wf (23)VIDEO 3 INPUT (jacks) rs (9)

BUTTON DESCRIPTIONS

`/1 (power) 1 (4, 17, 22, 31,32, 57)

</> eg (18, 29, 31, 37, 38)

ALPHABETICAL ORDER

0 – 92 CH ea (27)

A – DA.DEC ed (25, 27)AM (Except for models of area

code CEL, CEK) ej (32, 33)AUX wj (23)CD/SACD wd (23)CINEMA STUDIO EX A,B,C qh

(26)Digital Cinema Sound (indicator)qj (25)

DIMMER 5 (24)DISPLAY 4 (24, 35, 55)Display qg (24)DVD/LD wh (23)

E – KENTER ef (37)EQ 9 (31, 59)EQUALIZER qk (31)FM (Except for models of area

code CEL, CEK) ek (32, 33)

How to use this pageUse this page to find the location of buttons that arementioned in the text.

Illustration number r

NAME qf (37) R R

Name of button/part Reference page

6GB

Required cords

AAudio cord (not supplied)White (L) White (L)Red (R) Red (R)

BAudio/video cord (not supplied)Yellow (video) Yellow (video)

White (L/audio) White (L/audio)Red (R/audio) Red (R/audio)

C Video cord (not supplied)Yellow (video) Yellow (video)

DOptical digital cord (not supplied)Black Black

ECoaxial digital cord (not supplied)Orange Orange

FMonaural audio cord (not supplied)Black Black

GMonaural mini-plug cord (not supplied)Black Black

Before you get started

• Turn off the power to all components before making any connections.

• Do not connect the AC power cord until all of the connections are completed.

• Be sure to make connections firmly to avoid hum and noise.

• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks onthe components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.

• When you connect optical digital cords, insert the cord plugs straight in until they click into place.

• Do not bend or tie the optical digital cord.

Hooking Up the Components

Ho

ok

ing

Up

the

Co

mp

on

en

ts

7GB

Antenna hookups

FM wire antenna*(supplied)

AM loop antenna(supplied)

Notes on antenna hookups

• To prevent noise pickup, keep the AM loopantenna away from the receiver and othercomponents.

• Be sure to fully extend the FM wire antenna.

• After connecting the FM wire antenna, keep itas horizontal as possible.

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

SUBWOOFER

MULTI CH INFRONT SURROUND

CENTER

IN INOUT

CD/SACDIN

AUX

R

L

R

L

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT

VIDEO OUT VIDEO IN VIDEO OUT

S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

* The shape of the connector varies depending on the area code.

8GB

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

SUBWOOFER


CENTER

IN INOUTIN

AUX

R

L

R

L

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

INOUT

LINE

L

R

LINE

INPUT OUTPUT

LINE

L

R

OUTPUT

ç

ç

AA

A

CD/SACD

MD or Tape deck

CD or SACD player

Audio component hookups

Ho

ok

ing

Up

the

Co

mp

on

en

ts

9GB

COMPONENT VIDEO SPEAKERS IMPEDANCE USE 8 – 16Ω

Y

PB B-Y

PR R-Y

DVD/LDIN

VIDEO 2IN

MONITOROUT

R L R L

SPEAKERS IMPEDANCE USE 8 – 16Ω

FRONT ACENTERSURROUNDAUDIO IN

VIDEO IN

S-VIDEO IN

ENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

IN INOUT

CD/SACDIN

AUX

R

L

MD/TAPE

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

AC OUTLETL

R

FRONT B

R L

R L

VIDEOOUT

R

AUDIOOUT

VIDEOIN

AUDIOIN

OUTPUTINPUT

L

IN

AUDIO OUT VIDEO OUTLR

OUTPUT

VIDEOOUT

R

AUDIOOUT

OUTPUT

L

VIDEOIN

INPUT

Ç

INOUT

Ç

Ç

CB B B B

B

COMPONENT VIDEO*

VIDEO 1

Video component hookups

To the frontpanel

Camcorderor video

game TV monitor

DVD or LD player

Note on video componenthookups

You can connect your TV’s audio output jacksto the VIDEO 2 AUDIO IN jacks on thereceiver and apply sound effects to the audiofrom the TV. In this case, do not connect theTV’s video output jack to the VIDEO 2VIDEO IN jack on the receiver. If you areconnecting a separate TV tuner (or satellitetuner), connect both the audio and video outputjacks to the receiver as shown above.

If you have a DVD player, TV, satellite tuneror LD player with COMPONENT VIDEO(Y, B-Y, R-Y) output jacks and a monitor withCOMPONENT VIDEO input jacks, use avideo cord (not supplied) to connect to thereceiver.

TipWhen using the S-video jacks instead of the videojacks, your monitor must also be connected via anS-video jack. S-video signals are on a separate busfrom the video signals and will not be output throughthe video jacks.

NoteOn this receiver, the component video signals are notcompatible with S-video signals or video signals.

* Except for models of area code CEL, CEK.

VCR

TV tuner,satellitetuner or

VCR

10GB

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

SUBWOOFERFRONT SURROUND

CENTER

IN INOUT

CD/SACDIN

AUX

R

L

R

L

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

VIDEOOUT

R

AUDIOOUT

OUTPUT

L

DIGITALCOAXIAL

OUTPUTVIDEOOUT

R

AUDIOOUT

OUTPUT

L

DIGITALOPTICAL

OUTPUT

BD

E B

MULTI CH IN

Digital component hookups

DVD or LD player(etc.)*

Connect the digital output jacks of your DVD player and satellite tuner (etc.) to the receiver’s digitalinput jacks to bring the multi channel surround sound of a movie theater into your home. To fullyenjoy multi channel surround sound, five speakers (two front speakers, two surround speakers, and acenter speaker) and a sub woofer are required. You can also connect an LD player with an RF OUTjack via an RF demodulator, like the Sony MOD-RF1 (not supplied).

NoteYou cannot connect an LD player’s DOLBY DIGITAL RF OUT jack directly to this unit’s digital input jacks.You must first convert the RF signal to either an optical or coaxial digital signal. For details, see“Troubleshooting” on page 53.

TV tuner, satellitetuner or

DVD player*

* Make either coaxial or optical connections. We recommend making coaxial connections instead of opticalconnections.

Ho

ok

ing

Up

the

Co

mp

on

en

ts

11GB

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

SUBWOOFER


CENTER

IN INOUT

CD/SACDIN

AUX

R

L

R

L

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

INOUT

ç

ç ç

LINE

L

R

LINE

INPUT OUTPUTDIGITAL

INOPTICAL

OUT

IN

D

OUT

ç

D A A

MD/TAPEOUT

CD/SACD

IN

Connect the digital output jacks of your MD or tape deck to the receiver’s digital input jack andconnect the digital input jacks of your MD or tape deck to the receiver’s digital output jack. Theseconnections allow you to make digital recordings of TV broadcasts, etc.

MD or tape deck

Notes• You cannot make digital recordings when the source is a multi channel digital source.• All the OPTICAL and COAXIAL jacks are compatible with 96 kHz, 48 kHz, 44.1 kHz and 32 kHz sampling

frequencies.• It is not possible to record analog signals to the components connected to MD/TAPE and VIDEO jacks with

only digital connections. To record analog signals, make analog connections. To record digital signals, makedigital connections.

• The sound is not output when you play a SACD disc on the SACD player connected to the CD/SACDOPTICAL IN jack on this unit. Connect to the analog input jacks (CD/SACD IN jacks). Refer to the operatinginstructions supplied with the SACD player.

12GB

Multi channel input hookupsAlthough this receiver incorporates a multi channel decoder, it is also equipped with multi channelinput jacks. These connections allow you to enjoy multi channel software encoded in formats otherthan Dolby Digital and DTS. If your DVD player is equipped with multi channel output jacks, youcan connect them directly to the receiver to enjoy the sound of the DVD player’s multi channeldecoder. Alternatively, the multi channel input jacks can be used to connect an external multi channeldecoder.

To fully enjoy multi channel surround sound, five speakers (two front speakers, two surroundspeakers, and a center speaker) and a sub woofer are required. Refer to the operating instructionssupplied with your DVD player, multi channel decoder, etc., for details on the multi channelhookups.

Notes• When using the connections described below, adjust the level of the surround speakers and sub woofer from the

DVD player or multi channel decoder.• See page 15 for details on speaker system hookup.

DVD player,Multichannel decoder, etc.

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

FRONT

CENTER

IN INOUT

CD/SACDIN

AUX

R

LL

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

L

R

FRONT SURROUNDSUB

WOOFER

A A F F

MULTI CH OUT

CENTER

SURROUNDSUB

WOOFER

R

MULTI CH IN

Ho

ok

ing

Up

the

Co

mp

on

en

ts

13GB

OPTICAL

VIDEO 2IN

MD/TAPE

IN

MD/TAPEOUT

CD/SACD

IN

DVD/LDIN

AUDIO IN

VIDEO IN

S-VIDEO IN

ANTENNA

AM

COAXIAL

FM75Ω

SUBWOOFER

R

L

R

L

SUBWOOFER


CENTER

IN INOUT

CD/SACDIN

AUX

R

L

R

L

MD/TAPE

COAXIAL

CTRLA1

DVD/LD

MONITOR

AUDIO IN

VIDEO IN

S-VIDEO IN

VIDEO 2AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

DIGITAL

L

R

CONTROL A1

G

LINE

L

R

OUTPUT

INç

A

Other hookups

CONTROL A1 hookup

• If you have a CONTROL A1 compatibleSony CD player, SACD player, tapedeck, or MD deckUse a monaural mini-plug cord (notsupplied) to connect the CONTROL A1jack on the CD player, SACD player, tapedeck, or MD deck to the CTRL A1 jack onthe receiver. Refer to “CONTROL A1control system” on page 39 and the operatinginstructions supplied with your CD player,SACD player, tape deck, or MD deck fordetails.

NoteIf you make CONTROL A1 connections fromthe receiver to an MD deck that is also connectedto a computer, do not operate the receiver whileusing the “Sony MD Editor” software. This maycause a malfunction.

• If you have a Sony CD changer with aCOMMAND MODE selectorIf your CD changer’s COMMAND MODEselector can be set to CD 1, CD 2, or CD 3,be sure to set the command mode to “CD 1”and connect the changer to the CD jacks onthe receiver.However, if you have a Sony CD changerwith VIDEO OUT jacks, set the commandmode to “CD 2” and connect the changer tothe VIDEO 2 jacks on the receiver.

continued

CD player, tapedeck, MD deck, etc.

14GB

AUX AUDIO In hookup

If you have an individual audio component(except PHONO)Use the audio cords to connect the LINE OUTjacks on the CD player, tape deck or MD deckto the AUX IN jacks on the receiver so that youcan listen to stereo sources in surround sound.

Setting the voltage selector

If your receiver has a voltage selector on therear panel, check that the voltage selector is setto the local power supply voltage. If not, use ascrewdriver to set the selector to the correctposition before connecting the AC power cordto a wall outlet.

AC power cord

To a wall outlet

Connecting the AC powercord

* Except for models of area code ARThe configuration, shape, and number of AC outletsvary according to the model and country to whichthe receiver is shipped.

Before connecting the AC power cord of thisreceiver to a wall outlet, connect the speakersystem to the receiver (page 15).

Connect the AC power cord(s) of your audio/video components to a wall outlet.

If you connect other audio/video components tothe AC OUTLET(s) on the receiver, thereceiver will supply power to the connectedcomponent(s), allowing you to turn the wholesystem on or off when you turn the receiver onor off.

CautionMake sure that the total power consumption of thecomponent(s) connected to the receiver’s ACOUTLET(s) does not exceed the wattage stated on therear panel. Do not connect high-wattage electricalhome appliances such as electric irons, fans, or TVsto this outlet.

120V 240V 220V

VOLTAGE SELECTORVOLTAGE SELECTOR


R L

MPEDANCE USE 8 – 16Ω

FRONT AR

AC OUTLET

b

FRONT B

R L

R L

b

AC OUTLET*

Other hookups (continued)

Ho

ok

ing

Up

an

d S

ettin

g U

p th

e S

pe

ak

er S

ystem

15GB

Speaker system hookups

Required cords

A Speaker cords (not supplied)(+) (+)

(–) (–)

BMonaural audio cord (not supplied)Black Black

Hooking Up and Setting Up the Speaker System

Front speaker A(L)

Front speaker A(R)

Center speakerSurround speaker(L)

Surround speaker(R)

Active sub woofer

* If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals.

COMPONENT VIDEO

Y

PB B-Y

PR R-Y

DVD/LDIN

VIDEO 2IN

MONITOROUT

R L R L

FRONT ACENTERSURROUNDSUBWOOFER

R

L

MONITOR

AUDIO OUT


S-VIDEOOUT

AUDIO IN

S-VIDEO IN

S-VIDEO OUT

AUDIOOUT

VIDEO 1

AC OUTLET

FRONT B

R L

R L

E eE e

E e E e E e

INPUTAUDIO

IN

A AB

A A A A A

E e E e



Front speaker B*(R)

Front speaker B*(L)

continued

16GB

Stripped cords are touching each otherdue to excessive removal of insulation.

After connecting all the components,speakers, and AC power cord, outputa test tone to check that all thespeakers are connected correctly.For details on outputting a test tone,see page 22.

If no sound is heard from a speaker whileoutputting a test tone or a test tone is outputfrom a speaker other than the one whose nameis currently displayed on the receiver, thespeaker may be short-circuited. If this happens,check the speaker connection again.

To avoid damaging yourspeakers

Make sure that you turn down the volumebefore you turn off the receiver. When you turnon the receiver, the volume remains at the levelyou turn off the receiver.

Speaker system hookups (continued)

Notes• Twist the stripped ends of the speaker cords about

10 mm (2/3 inch). Be sure to match the speakercord to the appropriate terminal on the components:+ to + and – to –. If the cords are reversed, thesound will be distorted and will lack bass.

• If you use speakers with low maximum input rating,adjust the volume carefully to avoid excessiveoutput on the speakers.

To avoid short-circuiting thespeakers

Short-circuiting of the speakers may damagethe receiver. To prevent this, make sure to takethe following precautions when connecting thespeakers.

Make sure the stripped ends of eachspeaker cord does not touch anotherspeaker terminal, the stripped end ofanother speaker cord, or the metal parts ofthe receiver.

Examples of poor conditions of thespeaker cord

Stripped speaker cord is touching anotherspeaker terminal.

Ho

ok

ing

Up

an

d S

ettin

g U

p th

e S

pe

ak

er S

ystem

17GB

Performing initial setupoperations

Once you have hooked up the speakers andturned on the power, clear the receiver’smemory. Then specify the speaker parameters(size, position, etc.) and perform any otherinitial setup operations necessary for yoursystem.

TipTo check the audio output during settings (to set upwhile outputting the sound), check the connection(page 22).

Clearing the receiver’smemory

Before using your receiver for the first time, orwhen you want to clear the receiver’s memory,do the following.

This procedure is not necessary if thedemonstration activates when you turn on thepower.

1 Turn off the receiver.

2 Hold down ?/1 for 5 seconds.The demonstration starts (page 4) and all ofthe following items are reset or cleared:

• All preset stations are reset or cleared.• All sound field parameters are reset to

their factory settings.• All index names (of preset stations and

program sources) are cleared.• All SET UP parameters are reset to

their factory settings.• The sound field memorized for each

program source and preset stations arecleared.

• The master volume is set to VOL MIN.

45°

90°

20°

A A

B

CC

Performing initial setupoperations

Before using your receiver for the first time,adjust SET UP parameters so that the receivercorrespond to your system. For the adjustableparameters, see the table on page 59. See pages17–22 for speaker settings and pages 38–39 forother settings.

Multi channel surroundsetup

For the best possible surround sound, allspeakers should be the same distance from thelistening position (A).

However, the receiver lets you place the centerspeaker up to 1.5 meters (5 feet) closer (B)and the surround speakers up to 4.5 meters (15feet) closer (C) to the listening position.

The front speakers can be placed from 1.0 to12.0 meters (3 to 40 feet) from the listeningposition (A).

You can place the surround speakers eitherbehind you or to the side, depending on theshape of your room (etc.).

When placing surround speakers to your side

continued

18GB

Multi channel surround setup(continued)

When placing surround speakers behind you

NoteDo not place the center speaker farther away from thelistening position than the front speakers.

Normal Speaker and MicroSatellite Speaker

If you are using Select

Normal Speakers NORM. SP.

Micro Satellite Speakers MICRO SP.

The speaker size and the sub woofer selectionhas been preset to NORM. SP. You can adjustthe speaker size and sub woofer selection whenyou select NORM. SP. (pages 18–19)

To select MICRO SP., turn off the power, thenturn on again while pressing LEVEL. (To resetto NORM. SP., do the same procedure.)

When you select MICRO SP., the speaker sizeand sub woofer selection has been configuratedas follows:

Speaker Settings

FRONT SMALL

CENTER SMALL

SURROUND SMALL

SUB WOOFER YES

You cannot change the configuration if youselect MICRO SP.

TipThe setting for Micro Satellite Speaker (MICRO SP.)has been programmed to optimize the sound balance.If you use Sony’s Micro Satellite Speakers, selectMICRO SP.

CautionWhen you use Micro Satellite Speakers and thespeaker size is set to “LARGE”, you may not obtainthe correct soundstage. The speaker may also bedamaged at high volume position.

Specifying the speakerparameters

1 Press SET UP.

2 Press or to select the parameteryou want to adjust.

3 Turn the jog dial to select the settingyou want.The setting is entered automatically.

4 Repeat steps 2 and 3 until you have setall of the parameters that follow.

Initial settings

Parameter Initial setting

L R (FRONT) LARGE*

C (CENTER) LARGE*

SL SR (SURROUND) LARGE*

SW (SUB WOOFER) S.W. XXX YES*

L R DIST. XX.X m (ft.)** 5.0 m (16 ft.)**

C DIST. XX.X m (ft.)** 5.0 m (16 ft.)**

SL SR DIST. XX.X m (ft.)** 3.5 m (11 ft.)**

SL SR PL. XXX BEHD.

SL SR HGT. XXX LOW

* You can set this parameter only when you selectNORM. SP.

** Models of area code U, CA only.

45°

90°

20°

A A

B

CC

Ho

ok

ing

Up

an

d S

ettin

g U

p th

e S

pe

ak

er S

ystem

19GB

x Front speaker size ( L R )

• If you connect large speakers that willeffectively reproduce bass frequencies, select“LARGE”. Normally, select “LARGE”.

• If the sound is distorted, or you feel a lack ofsurround effects when using multi channelsurround sound, select “SMALL” to activatethe bass redirection circuitry and output thefront channel bass frequencies from the subwoofer.

• When the front speakers are set to “SMALL”,the center and surround speakers are alsoautomatically set to “SMALL” (unlesspreviously set to “NO”).

x Center speaker size ( C )• If you connect a large speaker that will

effectively reproduce bass frequencies, select“LARGE”. Normally, select “LARGE”.However, if the front speakers are set to“SMALL”, you cannot set the center speaker to“LARGE”.

• If the sound is distorted, or you feel a lack ofsurround effects when using multi channelsurround sound, select “SMALL” to activatethe bass redirection circuitry and output thecenter channel bass frequencies from the frontspeakers (if set to “LARGE”) or sub woofer.*1

• If you do not connect a center speaker, select“NO”. The sound of the center channel will beoutput from the front speakers.*2

x Surround speaker size ( SL SR )• If you connect large speakers that will

effectively reproduce bass frequencies, select“LARGE”. Normally, select “LARGE”.However, if the front speakers are set to“SMALL”, you cannot set the surroundspeakers to “LARGE”.

• If the sound is distorted, or you feel a lack ofsurround effects when using multi channelsurround sound, select “SMALL” to activatethe bass redirection circuitry and output thesurround channel bass frequencies from the subwoofer or other “LARGE” speakers.

• If you do not connect surround speakers, select“NO”.*3

Tip*1–*3 correspond to the following Dolby Pro Logicmodes*1 NORMAL*2 PHANTOM*3 3 STEREO

TipInternally, the LARGE and SMALL settings for eachspeaker determine whether or not the internal soundprocessor will cut the bass signal from that channel.When the bass is cut from a channel, the bassredirection circuitry sends the corresponding bassfrequencies to the sub woofer or other “LARGE”speakers.However, since bass sounds have a certain amount ofdirectionality, it is best not to cut them, if possible.Therefore, even when using small speakers, you canset them to “LARGE” if you want to output the bassfrequencies from that speaker. On the other hand, ifyou are using a large speaker, but prefer not to havebass frequencies output from that speaker, set it to“SMALL”.If the overall sound level is lower than you prefer, setall speakers to “LARGE”. If there is not enough bass,you can use the equalizer to boost the bass levels. Toadjust the equalizer, see page 31.

continued

20GB

x Sub woofer selection ( SW S.W. XXX)

• If you connect a sub woofer, select “YES”.

• If you do not connect a sub woofer, select“NO”. This activates the bass redirectioncircuitry and outputs the LFE signals from otherspeakers.

• In order to take full advantage of the DolbyDigital bass redirection circuitry, werecommend setting the sub woofer’s cut offfrequency as high as possible.

x Front speaker distance ( L R DIST.XX.X m (ft.))

Set the distance from your listening position tothe front speakers (A on page 17).

x Center speaker distance ( C DIST.XX.X m (ft.))

Set the distance from your listening position tothe center speaker. Center speaker distanceshould be set from a distance equal to the frontspeaker distance (A on page 17) to a distance1.5 meters (5 feet) closer to your listeningposition (B on page 17).

x Surround speaker distance ( SL SR

DIST. XX.X m (ft.))Set the distance from your listening position tothe surround speakers. Surround speakerdistance should be set from a distance equal tothe front speaker distance (A on page 17) to adistance 4.5 meters (15 feet) closer to yourlistening position (C on page 17).

TipThe receiver allows you to input the speaker positionin terms of distance. However, it is not possible to setthe center speaker further than the front speakers.Also, the center speaker cannot be set more than1.5 meters (5 feet) closer than the front speakers.Likewise, the surround speakers can not be set fartheraway from the listening position than the frontspeakers. And they can be no more than 4.5 meters(15 feet) closer.This is because incorrect speaker placement is notconducive to enjoy surround sound.Please note that, setting the speaker distance closerthan the actual location of the speakers will cause adelay in the output of the sound from that speaker. Inother words, the speaker will sound like it is fartheraway.For example, setting the center speaker distance1~2 m (3~6 feet) closer than the actual speakerposition will create a fairly realistic sensation of being“inside” the screen. If you cannot obtain a satisfactorysurround effect because the surround speakers are tooclose, setting the surround speaker distance closer(shorter) than the actual distance will create a largersound stage.Adjusting these parameter while listening to thesound often results in much better surround sound.Give it a try!


Ho

ok

ing

Up

an

d S

ettin

g U

p th

e S

pe

ak

er S

ystem

21GB

x Surround speaker position ( SL SR

PL. XXX)*This parameter lets you specify the location ofyour surround speakers for properimplementation of the Digital Cinema Soundsurround modes. Refer to the illustration below.

• Select “SIDE” if the location of your surroundspeakers corresponds to section A.

• Select “MID” if the location of your surroundspeaker corresponds to section B.

• Select “BEHD.” if the location of yoursurround speakers corresponds to section C.

x Surround speaker height ( SL SR

HGT. XXX)*This parameter lets you specify the height ofyour surround speakers for properimplementation of the Digital Cinema Soundsurround modes. Refer to the illustration below.

• Select “LOW” if the location of your surroundspeakers corresponds to section A.

• Select “HIGH” if the location of your surroundspeakers corresponds to section B.

* These parameters are not available when“Surround speaker size ( SL SR )” is set to“NO”.

TipThe surround speaker position parameter is designedspecifically for implementation of the Digital CinemaSound modes with virtual elements.With the Digital Cinema Sound modes, speakerposition is not as critical as other modes. All modeswith virtual elements were designed under thepremise that the surround speaker would be locatedbehind the listening position, but presentation remainsfairly consistent even with the surround speakerspositioned at a rather wide angle. However, if thespeakers are pointing towards the listener from theimmediate left and right of the listening position, thesound fields with virtual elements will not beeffective unless the surround speaker positionparameter is set to “PL. SIDE”.Nevertheless, each listening environment has manyvariables, like wall reflections, and you may obtainbetter results using “PL. MID.” and “PL. BEHD.” ifyour speakers are located high above the listeningposition, even if they are to the immediate left andright.Therefore, although it may result in a setting contraryto the “Surround speaker position” explanation, werecommend that you playback multi channel surroundencoded software and listen to the effect each settinghas on your listening environment. Choose the settingthat provides a good sense of spaciousness and thatbest succeeds in forming a cohesive space betweenthe surround sound from the surround speakers andthe sound of the front speakers. If you are not surewhich sounds best, select “PL. BEHD.” and then usethe speaker distance parameter and speaker leveladjustments to obtain proper balance.

continued

60

30A

B

A

B

60°

90°

20°

A

B30°BC C

A

22GB

Adjusting the speaker level

Use the remote while seated in your listeningposition to adjust the level of each speaker.

NoteThe receiver incorporates a new test tone with afrequency centered at 800 Hz for easier speaker leveladjustment.

1 Press ?/1 to turn on the receiver.

2 Press TEST TONE on the remote.“T. TONE” appears in the display and youwill hear the test tone from each speaker insequence.

3 Adjust the LEVEL parameters so thatthe level of the test tone from eachspeaker sounds the same when you arein your main listening position.Press LEVEL to adjust the balance andlevel of speakers. For details on the LEVELmenu, see page 29.While adjusting, the test tone is output fromthe speaker whose adjustment is performed.

4 Press TEST TONE again to turn off thetest tone.

TipYou can adjust the level of all speakers at the sametime. Turn MASTER VOLUME on the main unit orpress MASTER VOL +/– on the remote.

Notes• The test tone cannot be output when the receiver is

set to MULTI CH IN.• The adjusted value are shown in the display during

adjustment.• Although these adjustments can also be made via

the front panel using the LEVEL menu (when thetest tone is output, the receiver switches to theLEVEL menu automatically), we recommend youfollow the procedure described above and adjust thespeaker levels from your listening position using theremote.

Checking the connectionsAfter connecting all of your components to thereceiver, do the following to verify that theconnections were made correctly.

1 Press ?/1 to turn on the receiver.

2 Turn on the component that youconnected (e.g., CD player or tapedeck).

3 Press the function button to select thecomponent (program source).

4 Start playing.

If you do not obtain normal sound output afterperforming this procedure, see“Troubleshooting” on page 53 and take theappropriate measures to correct the problem.


Ba

sic O

pe

ratio

ns

23GB

Basic Operations

Selecting the component

Function buttons

Press the function button to select thecomponent you want to use.

To select Press

VCR VIDEO 1 or VIDEO 2

TV or satellite tuner VIDEO 2

Camcorder or VIDEO 3video game

DVD or LD player DVD/LD

MD or Tape deck MD/TAPE

CD or SACD player CD/SACD

Built in tuner TUNER

An audio component AUX

After turning on the component you selected,select the component and play the programsource.

• After selecting VCR, camcorder, video game,DVD player, or LD player, turn on the TV andset the TV’s video input to match thecomponent you selected.

INPUT MODE

Press INPUT MODE to select the input modefor your digital components.Each time you press the button, the input modeof the currently selected component switches.

Select To

AUTO IN Give priority to digitalsignals when there are bothdigital and analogconnections. If there are nodigital signals, analog isselected.

COAX IN Specify the digital audiosignals input to theDIGITAL COAXIAL inputjacks.

OPT IN Specify the digital audiosignals input to theDIGITAL OPTICAL inputjacks.

ANALOG Specify the analog audiosignals input to the AUDIOIN (L/R) jacks.

NoteWhen the 96 kHz digital signal is input, the equalizerand surround effects are turned off.

MULTI CH IN

Press MULTI CH IN to enjoy the audio sourceconnected to the MULTI CH IN jacks. You canadjust balance and level of all the speakers.When this function is on, the equalizer andsurround effects are turned off.

MULTI CHANNEL DECODINGindicator

This indicator lights up when the unit isdecoding signals recorded in a multi channelformat.

continued

24GB

SPEAKERS A/B

Press SPEAKERS A/B button to output thesound from the speakers connected to theSPEAKERS FRONT terminals.

Each time you press the button, the displaychanges cyclically as follows:

SP. A t SP. B t SP. OFF

To drive Select

Speaker System A SP. A(Connected to theSPEAKERS FRONT Aterminals)

Speaker System B SP. B(Connected to theSPEAKERS FRONT Bterminals)

When you select “SP. OFF”, no sound will beoutput from your speakers and “SP. OFF”lights up in the display.

MUTING

Press MUTING to mute the sound. The mutingfunction is canceled when you turn the poweron or turn the MASTER VOLUME clockwiseto turn the volume up.

PHONES

Use to connect headphones.

• When the headphones are connected, speakeroutput is automatically canceled and “SP. OFF”lights up in the display.

Selecting the component (continued) Changing the display

DISPLAY

Each time you press DISPLAY, the displaychanges cyclically as follows:

Index name of the component* t Selectedcomponent t Sound field applied to theprogram source

When the tuner is selectedIndex name of the preset station* or programstation name** t Frequency t Program typeindication** t Radio text** t Currenttime** t Sound field applied to the band orthe preset station

* Index name appears only when you have assignedone to the component or preset station (page 37).Index name does not appear when only blankspaces have been entered, or it is the same as thefunction.

** During RDS reception only. (Models of area codeCEL, CEK only. See page 35).

DIMMER

Press DIMMER repeatedly to adjust thebrightness of the display (3 steps).However, when you press any button, thedisplay becomes the brightest settingtemporary.

En

joyin

g S

urro

un

d S

ou

nd

25GB

Enjoying Surround Sound

You can take advantage of surround soundsimply by selecting one of the receiver’s pre-programmed sound fields. They bring theexciting and powerful sound of movie theatersand concert halls into your home. You can alsocustomize the sound fields to obtain the soundyou want by changing the surround parameter.To fully enjoy surround sound, you mustregister the number and location of youspeakers. See “Multi channel surround setup”starting from page 17 to set the speakerparameters before enjoying surround sound.

Automatically decodingthe input audio signal

Press A.DEC.“AUTO DEC.” appears in the display.

This mode automatically detects the type ofaudio signal being input (Dolby Digital, DTS,or standard 2 channel stereo) and performs theproper decoding if necessary. This modepresents the sound as it was recorded/encoded,without adding any effects (e.g. reverberation).

However, if there are no low frequency signals(Dolby Digital LFE, etc.) it will generate a lowfrequency signal for output to the sub woofer.

Selecting a sound fieldYou can enjoy surround sound simply byselecting one of the pre-programmed soundfields according to the program you want tolisten to.

Sound field Display

Normal Surround NORM.SURR.

Cinema Studio EX A C.ST.EX A DCS

Cinema Studio EX B C.ST.EX B DCS

Cinema Studio EX C C.ST.EX C DCS

Hall HALL

Jazz Club JAZZ

Live Concert CONCERT

Game GAME

About DCS (Digital Cinema Sound)The sound fields with DCSmark use DCStechnology. When these sound fields areselected, “Digital Cinema Sound” indicator inthe display lights up.

In collaboration with Sony PicturesEntertainment, Sony measured the soundenvironment of their studios and integrated thedata of the measurement and Sony’s own DSP(Digital Signal Processor) technology todevelop “Digital Cinema Sound”. In a hometheater, “Digital Cinema Sound” simulates anideal movie theater sound environment basedon the preference of the movie director.

Enjoying movies with CinemaStudio EX

Cinema Studio EX is ideal for enjoying themovie software encoded with multi channelformat, such as the Dolby Digital DVD. Thismode reproduces the sound characteristics ofSony Pictures Entertainment’s studios.

continued

26GB

Press CINEMA STUDIO EX A, B or C.The selected sound field is indicated in thedisplay.

x C.ST.EX A (Cinema Studio EX A)Reproduces the sound characteristics of theSony Pictures Entertainment “Cary GrantTheater” cinema production studio. This is astandard mode, great for watching most anytype of movie.

x C.ST.EX B (Cinema Studio EX B)Reproduces the sound characteristics of theSony Pictures Entertainment “Kim NovakTheater” cinema production studio. This modeis ideal for watching science-fiction or actionmovies with lots of sound effects.

x C.ST.EX C (Cinema Studio EX C)Reproduces the sound characteristics of theSony Pictures Entertainment scoring stage.This mode is ideal for watching musicals orclassic films where music is featured in thesoundtrack.

About Cinema Studio EXCinema Studio EX consists of the followingthree elements.

• Virtual Multi Dimension

Creates 5 sets of virtual speakerssurrounding the listener from a single pair ofactual surround speakers.

• Screen Depth Matching

In a movie theater, sound seems to comefrom inside the image reflected on the moviescreen. This element creates the samesensation in your listening room by shiftingthe sound of the front speakers “into” thescreen.

• Cinema Studio Reverberation

Reproduces the reverberations peculiar to amovie theater.

Cinema Studio EX is the integrated modewhich operates these elements simultaneously.

TipYou can select Cinema Studio EX by pressing MODErepeatedly.

Notes• The effects provided by the virtual speakers may

cause increased noise in the playback signal.• When listening with sound fields that employ the

virtual speakers, you will not be able to hear anysound coming directly from the surround speakers.

Selecting other sound fields

Press MODE repeatedly to select thesound field you want.The current sound field is indicated in thedisplay.

x NORM.SURR. (Normal Surround)Software with multi channel surround audiosignals is played back according to the way itwas recorded. Software with 2 channel audiosignals is decoded with Dolby Pro Logic tocreate surround effects.

x HALLReproduces the acoustics of a rectangularconcert hall.

x JAZZ (Jazz Club)Reproduces the acoustics of a jazz club.

x CONCERT (Live Concert)Reproduces the acoustics of a 300-seat liveconcert.

x GAMEObtains maximum audio impact from videogame software.

To turn the surround effect offPress A.DEC or 2CH.

Selecting a sound field (continued)

En

joyin

g S

urro

un

d S

ou

nd

27GB

Tips• The receiver lets you apply the last selected sound

field to a program source whenever it is selected(Sound Field Link). For example, if you listen toCD with “JAZZ” as the sound field, change to adifferent program source, then return to CD,“JAZZ” will be applied again.

• You can identify the encoding format of programsofware by looking at its packaging.Dolby Digital discs are labeled with the logo, and Dolby Surround encoded programs arelabeled with the logo.

• When sound signals with a sampling frequency of96 kHz are input, the sound signals are output instereo automatically, and the sound field is turnedoff.

Using only the frontspeakers (2 Channel Stereo)

Press 2CH.“2CH ST.” appears in the display.

This mode outputs the sound from the front leftand right speakers only. Standard 2 channel(stereo) sources completely bypass the soundfield processing. Multi channel surroundformats are downmixed to 2 channel.

Notes• No sound is output from the sub woofer when

“2CH ST.” is selected. To listen to 2 channel(stereo) sources using the front left and rightspeakers and a sub woofer, press A.DEC to select“AUTO DEC.”

• When you select “Micro Satellite Speaker” (page18), internal sound processor will automaticallyredirect bass sound to sub woofer. If you want tolisten to two channel (stereo) sources under thissetting, we recommend that you choose“AUTO DEC.” mode so that you can takeadvantage of your sub woofer to obtain the correctbass signal.

Enjoying stereo sound inmulti channel (Dolby ProLogic )

The receiver can reproduce the stereo sound inmulti channel through Dolby Pro Logic . Youcan activate the decoder using the SET UPmenu. For details, see page 38.

28GB

PRO LOGIC

D.RANGE EQ

MONO RDSDTS MPEG STEREO

OPTSP. OFF

SL S SR

L

SW

C R

MEMORY

L F E

DIGITALa

COAX

1qd 2 3

7

5

6

4qs

qa 0

9 8

Understanding the multi channel surround displays

SL SR

L C R

1 ; DIGITAL: Lights up when the receiver isdecoding signals recorded in the DolbyDigital format.

2 PRO LOGIC: Lights up when the receiverapplies Pro Logic processing to 2 channelsignals in order to output the center andsurround channel signals. However, thisindicator does not light if the center andsurround speakers are set to “NO”, and“AUTO DEC.” or “NORM.SURR.” isselected.

NotePro Logic decoding does not function for MPEGformat signals.

3 DTS: Lights up when DTS signals are input.

NoteWhen playing a DTS format disc, be sure thatyou have made digital connections and thatINPUT MODE is NOT set to “ANALOG”(page 23).

4 MPEG: Lights up when MPEG signals areinput.

NoteOnly the front 2 channels are compatible withMPEG format. Multi channel surround sound isdownmixed and output from the front 2 channels.

5 Tuner indicators: Lights up when using thereceiver to tune in radio stations, etc. Seepages 32–36 for tuner operations.

Note“RDS” only appears for models of area codeCEL, CEK only.

6 EQ: Lights up when the equalizer functions.

7 D.RANGE: Lights up when dynamic rangecompression is activated. See page 30 toadjust the dynamic range compression.

8 COAX: Lights up when the source signal is adigital signal being input through theCOAXIAL terminal.

9 OPT: Lights up when the source signal is adigital signal being input through theOPTICAL terminal.

q; Playback channel indicators: The letters(L, C, R, etc.) indicate the channels beingplayed back. The boxes around the lettersvary to show how the receiver downmixes thesource sound (based on the speakers settings).When using sound fields like “C.ST.EX”, thereceiver adds reverberation based on thesource sound.

L (Front Left), R (Front Right), C (Center(monaural)), SL (Surround Left), SR(Surround Right), S (Surround (monaural orthe surround components obtained by ProLogic processing))

Example:Recording format (Front /Surround): 3/2Output channel: Surround speakers absentSound Field: AUTO DEC.

En

joyin

g S

urro

un

d S

ou

nd

29GB

qa L F E : Lights up when the disc beingplayed back contains the LFE (LowFrequency Effect) channel and when thesound of the LFE channel signal is actuallybeing reproduced.

qs SW: Lights up when sub woofer selection isset to “YES” (page 20) and the audio signal isoutput from the SUB WOOFER jacks.

qd SP. OFF: Lights up when headphones areinserted or the SPEAKERS A/B button is setto “SP. OFF”.

Customizing sound fieldsBy adjusting the surround parameters and theequalization of the front speakers, you cancustomize the sound fields to suit yourparticular listening situation.

Once you customize a sound field, the changesare stored in the memory indefinitely. You canchange a customized sound field any time bymaking new adjustments to the parameters.

See the tables on back page for the parametersavailable in each sound field.

To get the most from multichannel surround sound

Position your speakers and do the proceduresdescribed in “Multi channel surround setup”starting from page 17 before you customize asound field.

Adjusting the surroundparameter

The SURR menu contains parameter that letyou customize various aspects of the currentsound field. The settings are stored individuallyfor each sound field.

1 Start playing a program sourceencoded with multi channel surroundsound.

continued

2 Press SURR.The button lights up and the first parameteris displayed.


Initial settings


EFFECT (depends on the sound field)

Effect level (EFFECT)Lets you adjust the “presence” of the currentsurround effect.

Adjusting the levelparameters

The LEVEL menu contains parameters that letyou adjust the balance and volumes of eachspeaker. The settings are applied to all soundfields.


2 Press LEVEL.The button lights up and the first parameteris displayed.



30GB

Initial settings


L R BAL. L/R XXX* BALANCE

CTR XXX dB* 0 dB

SUR.L. XXX dB* 0 dB

SUR.R. XXX dB* 0 dB

S.W. XXX dB* 0 dB

L.F.E. XXX dB 0 dB

D. RANGE COMP. XXX OFF

* The parameters can be adjusted separately forMULTI CH IN.

Front balance ( L R BAL. L/RXXX)Lets you adjust the balance between front leftand right speakers.

Center level (CTR XXX dB)Lets you adjust the level of the center speaker.

Surround left level (SUR.L. XXX dB)Lets you adjust the level of the surround leftspeaker.

Surround right level (SUR.R. XXX dB)Lets you adjust the level of the surround rightspeaker.

Sub woofer level (S.W. XXX dB)Lets you adjust the level of the sub woofer.

Customizing sound fields (continued) LFE (Low Frequency Effect) mixlevel (L.F.E. XXX dB)Lets you attenuate the level of the LFE (LowFrequency Effect) channel output from the subwoofer without effecting the level of the bassfrequencies sent to the sub woofer from thefront, center or surround channels via theDolby Digital or DTS bass redirectioncircuitry.

• For LFE mix level, “0 dB” outputs the full LFEsignal at the mix level determined by therecording engineer.

• To mute the sound of the LFE channel from thesub woofer, select “OFF”. However, the lowfrequency sounds of the front, center, orsurround speakers are output from the subwoofer according to the settings made for eachspeaker in the speaker setup (pages 17–21).

Dynamic range compressor ( D. RANGE

COMP. XXX)Lets you compress the dynamic range of thesound track. This may be useful when you wantto watch movies at low volumes late at night.We recommend using the “MAX” setting.

• To reproduce the sound track with nocompression, select “OFF”.

• To reproduce the sound track with the dynamicrange intended by the recording engineer, select“STD”.

• To compress the dynamic range in small stepsto achieve the sound you desire, select “0.1”–“0.9”.

• To reproduce a dramatic compression of thedynamic range, select “MAX”.

NoteDynamic range compression is possible with DolbyDigital sources only.

En

joyin

g S

urro

un

d S

ou

nd

31GB

Adjusting the equalizer

The EQ menu lets you adjust the equalizationof the front speakers. The settings are storedindividually for each sound field.


2 Press EQ.The button lights up and the first parameteris displayed.

3 Press or to select the parameter(gain (dB)) you want to adjust.


To turn on/off the equalizerPress EQUALIZER. The EQ indicator in thedisplay lights up when the equalizer is turnedon. When you adjust the equalizer using the EQparameters, the settings are stored separatelyfor each sound field and can be reproducedwhenever you turn on the equalizer.

Front speaker bass adjustment(Gain)Lets you adjust the gain of bass.

Front speaker treble adjustment(Gain)Lets you adjust the gain of treble.

Gain (dB)

Resetting customized soundfields to the factory settings

1 If the power is on, press ?/1 to turn offthe power.

2 Hold down MODE and press ?/1.“SF. CLR.” appears in the display and allsound fields are reset at once.

32GB

Receiving Broadcasts

Before receiving broadcasts, make sure youhave connected FM and AM antennas to thereceiver (page 7).

Storing FM stationsautomatically(AUTOBETICAL)

(Models of area code CEL, CEK only)This function lets you store up to 30 FM andFM RDS stations in alphabetical order withoutredundancy. Additionally, it only stores thestations with the clearest signals.

If you want to store FM or AM stations one byone, see “Presetting radio stations” on page 34.

1 Press ?/1 to turn off the receiver.

2 Hold down MEMORY and press ?/1 toturn the receiver back on.“AUTO-BETICAL SELECT” appears inthe display and the receiver scans and storesall the FM and FM RDS stations in thebroadcast area.For RDS stations, the tuner first checks forstations broadcasting the same program,then stores only the one with the clearestsignal. The selected RDS stations are sortedalphabetically by their Program Servicename, then assigned a 2-character presetcode. For more details on RDS, see page 35.Regular FM stations are assigned2-character preset codes and stored after theRDS station.When done, “FINISH” appears in thedisplay momentarily and the receiverreturns to the normal operation.

Notes• Do not press any button on the receiver or supplied

remote during autobetical operation.• If you move to another area, repeat this procedure

to store stations in your new area.• For details on tuning the stored stations, see page

34.• If you move the antenna after storing stations with

this procedure, the stored settings may no longer bevalid. If this happens, repeat this procedure to storethe stations again.

Direct tuningYou can enter a frequency of the station youwant directly by using the numeric buttons onthe supplied remote. For details on the buttonsused in this section, see pages 42–48 for remoteRM-PP411 and pages 49–52 for remoteRM-U305C.

1 Press TUNER on the remote.The last received station is tuned in.

2 Press FM* or AM* to select the FM orAM band.

3 Press D. TUNING on the remote.

4 Press the numeric buttons to enter thefrequency.Example 1: FM 102.50 MHz

Example 2: AM 1350 kHz(You don’t have to enter the last “0” when thetuning scale is set to 10 kHz.)

If you cannot tune in a station and theentered numbers flashMake sure you’ve entered the rightfrequency. If not, repeat steps 3 and 4.If the entered numbers still flash, thefrequency is not used in your area.

* For models of area code CEL, CEK: FM/AM.

b b b b1 0 2 5 0

b b b1 3 5 0

Re

ce

iving

Bro

ad

ca

sts

33GB

5 If you’ve tuned in an AM station, adjustthe direction of the AM loop antenna foroptimum reception.

6 Repeat steps 2 to 5 to receive anotherstation.

Tips• If you do not remember the precise frequency, press

TUNING + or TUNING – after entering the valueclose to the frequency you want. The receiverautomatically tunes in the station you want. If thefrequency seems to be higher than the enteredvalue, press TUNING +, and if the frequency seemsto be lower than the entered value, pressTUNING –.

• If “STEREO” flashes in the display and the FMstereo reception is poor, press FM MODE to changeto monaural (MONO). You will not be able to enjoythe stereo effect, but the sound will be lessdistorted. To return to stereo mode, pressFM MODE again.

The tuning scale differs depending on the area codeas shown in the following table. For details on areacodes, see page 4.

Area code FM AM

U, CA 100 kHz 10 kHz*

AU, SP, CEL, 50 kHz 9 kHzCEK, TW

E2/E3, AR, MX 50 kHz 9 kHz*

* The AM tuning scale can be changed (page 57).

Automatic tuningIf you don’t know the frequency of the stationyou want, you can let the receiver scan allavailable stations in your area.

1 Press TUNER.The last received station is tuned in.

2 Press FM** or AM** to select the FM orAM band.

3 Press TUNING + or TUNING –.Press TUNING + to scan from low to high;press TUNING – to scan from high to low.The receiver stops scanning whenever astation is received.

When the receiver reaches either end ofthe bandScanning is repeated in the same direction.

4 To continue scanning, press TUNING +or TUNING – again.

** For models of area code CEL, CEK: FM/AM.

Preset tuningAfter you have tuned in stations using DirectTuning or Automatic Tuning, you can presetthem to the receiver. Then you can tune in anyof the stations directly by entering its2-character preset code using the suppliedremote. Up to 30 FM or AM stations can bepreset. The receiver will also scan all thestations that you have preset.

Before tuning to preset stations, be sure topreset them by performing steps on “Presettingradio stations” (page 34).

continued

34GB

Preset tuning (continued)

Presetting radio stations


2 Tune in the station that you want topreset using Direct Tuning (page 32) orAutomatic Tuning (page 33).

3 Press MEMORY.“MEMORY” appears in the display for afew seconds.Do steps 4 to 6 before “MEMORY” goesout.

4 Press SHIFT to select a memory page(A, B or C).Each time you press SHIFT, the letter “A”,“B”, or “C” appears in the display.

5 Press PRESET TUNING +* or PRESETTUNING –* to select a preset number.If “MEMORY” goes out before you pressthe preset number, start again from step 3.

6 Press MEMORY again to store thestation.If “MEMORY” goes out before you canstore the station, start again from step 3.

7 Repeat steps 2 to 6 to preset anotherstation.

* For models of area code CEL, CEK: PRESET/PTYSELECT + or PRESET/PTY SELECT –.

To change a preset number toanother stationDo steps 1 to 6 to preset a new station to thenumber.

Tuning to preset stations

You can tune the preset stations by either of thefollowing two ways.

Scanning the preset stations


2 Press PRESET TUNING +* or PRESETTUNING –* repeatedly to select thepreset station you want.Each time you press the button, the receivertunes in one preset station at a time, in thecorresponding order and direction asfollows:

* For models of area code CEL, CEK: PRESET/PTYSELECT + or PRESET/PTY SELECT –.

Using the preset codesUse the supplied remote to perform thefollowing operations. For details on the buttonsused in this section, see pages 42–48 for remoteRM-PP411 and pages 49–52 for remoteRM-U305C.

1 Press TUNER on the remote.The last received station is tuned in.

2 Press SHIFT to select a memory page(A, B, or C), then press the presetnumber of the station you want usingthe numeric buttons.

nA1˜A2˜...˜A0˜B1˜B2˜...˜B0N

nC0˜...C2˜C1N

Re

ce

iving

Bro

ad

ca

sts

35GB

Using the Radio DataSystem (RDS)

(Models of area code CEL, CEK only)This receiver also allows you to use RDS(Radio Data System), which enables radiostations to send additional information alongwith the regular program signal. You can usethe following convenient RDS features:

– Displaying RDS information

– Scanning preset stations by program type

Note that RDS is operable only for FMstations.*

* Not all FM stations provide RDS service, nor dothey provide the same types of services. If you arenot familiar with the RDS services in your area,check with your local radio stations for details.

Receiving RDS broadcasts

Simply select a station on the FM bandusing direct tuning (page 32), automatictuning (page 33), or preset tuning(page 33).When you tune in a station that provides RDSservices, the RDS indicator lights up and theprogram station name normally appears in thedisplay.

NoteRDS may not work properly if the station you tunedto is not transmitting the RDS signal properly or if thesignal strength is weak.

Displaying RDS information

While receiving an RDS station, pressDISPLAY.Each time you press the button, RDSinformation on the display changes cyclicallyas follows:

Program Station name t Frequency tProgram Type indicationa) tRadio Text indicationb) t Current Timeindication (in 24-hour system) t Sound fieldcurrectly applied

a) Type of program being broadcast (page 36).b) Text messages sent by the RDS station.

Notes• If there is an emergency announcement by

government authorities, “ALARM” flashes in thedisplay.

• When the message consists of 9 characters or more,the message scrolls across the display.

• If a station does not provide a particular RDSservice, “NO XXX” (such as “NO PTY”) appears inthe display.

Scanning preset stations byprogram type

You can tune in preset stations according to aprogram type that you specify. The receiverscans for stations in its preset memory currentlybroadcasting the specified program type.

1 Press PTY.

2 Press PRESET/PTY SELECT + orPRESET/PTY SELECT – to select theprogram type.See the table below for the information oneach program type.

3 Press PTY.While the receiver is scanning stations,“SEARCH” and the programme type aredisplayed alternately.When the receiver finds a station, thereceiver stops scanning. When the receivercould not find any preset stations currentlybroadcasting the specified program type,“NO PTY” appears in the display.

continued

36GB

Description of program types

Program type Descriptionindication

NEWS News programs

AFFAIRS Topical programs that expandon current news

INFO Programs offering information ona wide spectrum of subjects,including consumer affairs andmedical advice

SPORT Sports programs

EDUCATE Educational programs, such as“how-to” and advice programs

DRAMA Radio plays and serials

CULTURE Programs about national orregional culture, such as languageand social concerns

SCIENCE Programs about the naturalsciences and technology

VARIED Other types of programs such ascelebrity interviews, panel games,and comedy

POP M Popular music programs

ROCK M Rock music programs

EASY M Easy Listening

LIGHT M Instrumental, vocal, and choralmusic

CLASSICS Performances of major orchestras,chamber music, opera, etc.

OTHER M Music that does not fit into anycategories above, such as Rhythm& Blues and Reggae

WEATHER Weather information

FINANCE Stock market reports and trading,etc.

CHILDREN Programs for children

SOCIAL Programs about people and thethings that affect them

RELIGION Programs of religious content

PHONE IN Programs where members of thepublic express their views byphone or in a public forum

Preset tuning (continued) Program type Descriptionindication

TRAVEL Programs about travel. Not forannouncements that are located byTP/TA

LEISURE Programs on recreational activitiessuch as gardening, fishing,cooking, etc.

JAZZ Jazz programs

COUNTRY Country music programs

NATION M Programs featuring the popularmusic of the country or region

OLDIES Programs featuring oldies music

FOLK M Folk music programs

DOCUMENT Investigative features

NONE Any programs not defined above

Oth

er O

pe

ratio

ns

37GB

Other Operations

continued

4 Press ENTER.

5 Repeat steps 2 to 4 to assign indexname for another station or programsource.

Note(Models of area code CEL, CEK only)You cannot change the name of an RDS station.

RecordingBefore you begin, make sure you’ve connectedall components properly.

Recording on an audio tapeor MiniDisc

You can record on a cassette tape or MiniDiscusing the receiver. See the operatinginstructions of your cassette deck or MD deckif you need help.

1 Select the component to be recorded.

2 Prepare the component for playing.For example, insert a CD into the CDplayer.

3 Insert a blank tape or MD into therecording deck and adjust therecording level, if necessary.

4 Start recording on the recording deck,then start playback on the playbackcomponent.

Notes• Sound adjustments do not affect the signal output

from the MD/TAPE OUT jacks.• The analog audio signals of the current function is

output from the REC OUT jacks.• When MULTI CH IN is selected, the analog audio

signals of the current function is output from theREC OUT jacks.

• You cannot record a digital audio signal using acomponent connected to the analog MD/TAPEOUT jacks. To record a digital audio signal,connect a digital component to the DIGITAL MD/TAPE OUT jacks.

Naming preset stationsand program sources

You can enter a name (index name) of up to 8characters for preset stations and programsources. These names (for example, “VHS”)appear in the receiver’s display when a stationor program source is selected. Note that nomore than one name can be entered for eachpreset station or program source.This function is useful for distinguishingcomponents of the same kind. For example,two VCRs can be specified as “VHS” and“8MM”, respectively. It is also handy foridentifying components connected to jacksmeant for another type of component, forexample, a second CD player connected to theMD/TAPE jacks.

1 To name a preset stationPress TUNER, then tune in the presetstation you want to create an indexname for.The last station you received is tuned in.If you are not familiar with how to tune inpreset stations, see “Tuning to presetstations” on page 34.

To name a program sourceSelect the program source (component)to be named.

2 Press NAME.

3 Create an index name by using the jogdial and or :Turn the jog dial to select a character, thenpress to move the cursor to the nextposition.

To insert a spaceTurn the jog dial until a blank space appearsin the display.

If you’ve made a mistakePress or repeatedly until the characterto be changed flashes, then turn the jog dialto select the right character.

38GB

Recording (continued) Using the Sleep TimerYou can set the receiver to turn offautomatically at a specified time.

Press SLEEP on the remote while thepower is on.Each time you press the button, the displaychanges cyclically as follows:

2-00-00 t 1-30-00 t 1-00-00 t 0-30-00t OFF

The display dims after you have specified thetime.

Tips• You can freely specify the time. After pressing

SLEEP, specify the time you want using the jog dialand / on the receiver. The sleep time changesin 1 minute intervals. You can specify up to 5hours.

• To check the remaining time before the receiverturns off, press SLEEP. The remaining timeappears in the display.

Adjustments using theSET UP button

The SET UP button allows you to make thefollowing adjustments.

1 Press SET UP.



4 Repeat steps 2 and 3 until you have setall of the parameters that follow.

Initial settings


C.MODE.AVX AV2

PRO LOGIC MOVIE

A.PWR – XXX YES

• Some sources contain copy guards to preventrecording. In this case, you may not be able torecord from the sources.

• When MULTI CH IN is selected, no signals areoutput from DIGITAL OUT jacks (MD/TAPEOPTICAL OUT).

Recording on a video tape

You can record from a VCR, a TV, a DVDplayer or an LD player using the receiver. Youcan also add audio from a variety of audiosources when editing a video tape. See theoperating instructions of your VCR or LDplayer if you need help.

1 Select the program source to berecorded.

2 Prepare the component for playing.For example, insert the laser disc you wantto record into the LD player.

3 Insert a blank video tape into the VCR(VIDEO 1) for recording.

4 Start recording on the recording VCR,then start playing the video tape orlaser disc you want to record.

TipYou can record the sound from any audio source ontoa video tape while copying from a video tape or laserdisc. Locate the point where you want to startrecording from another audio source, select theprogram source, then start playback. The audio fromthat source will be recorded onto the audio track ofthe video tape instead of the audio from the originalmedium. To resume audio recording from the originalmedium, select the video source again.

Notes• Make sure to make both digital and analog

connections to the VIDEO 2 and DVD/LD inputs.Analog recording is not possible if you make onlydigital connections.

• When MULTI CH IN is selected, the analog audiosignals of the current function is output from theREC OUT jacks.

Oth

er O

pe

ratio

ns

39GB

x CONTROL A1 auto power on(A.PWR – XXX)

Lets you turn on the receiver automaticallywhen the component connected via monauralminiplug cord (see page 13) is turned on andthe playback is started.

When set to “NO”, you can save the powerconsumption of the receiver during standbymode.

x Selecting the command mode of theremote (C.MODE.AVX)

Lets you select the command mode of theremote. Change the command mode when youuse 2 Sony receivers in the same room.

x 2ch decode mode ( PRO LOGIC )

Lets you specify the type of decoding for the 2channel source. This receiver incorporates withDolby Pro Logic II which has movie mode andmusic mode, and the receiver can reproduce the2 channel sound in 5.1 channel through DolbyPro Logic II.

• When set to “DOLBY PL”, the receiverperforms the Pro Logic decoding. The sourcerecorded in 2 channel is decoded into 4channels.

• When set to “II MOVIE”, the receiver performsthe Pro Logic II movie mode decoding. Thissetting is ideal for the movies encoded in DolbySurround. Besides, this mode can reproduce thesound in 5.1 channel when watching the videosof old movies or in the dubbed language.

• When set to “II MUSIC”, the receiver performsthe Pro Logic II music mode decoding. Thissetting is ideal for the normal stereo sources,such as CDs.

NoteDolby Pro Logic II does not function for DTS orMPEG format signals.

CONTROL A1 controlsystem

Getting Started

This section explains the basic functionsof the CONTROL A1 Control System.Certain components have specialfunctions, such as “CD Synchro Dubbing”on cassette decks, that require CONTROLA1 connections. For detailed informationregarding specific operations, be sure toalso refer to the Operating Instructionssupplied with your component(s).

The CONTROL A1 Control System wasdesigned to simplify the operation of audiosystems composed of separate Sonycomponents. CONTROL A1 connectionsprovide a path for the transmission of controlsignals which enable automatic operation andcontrol features usually associated withintegrated systems.

Currently, CONTROL A1 connectionsbetween a Sony CD player, amplifier(receiver), MD deck and cassette deck provideautomatic function selection and synchronizedrecording.

In the future, the CONTROL A1 connectionwill work as a multifunction bus allowing youto control various functions for eachcomponent.

Notes• The CONTROL A1 Control System is designed to

maintain upward compatibility as the ControlSystem is upgraded to handle new functions. In thiscase, however, older components will not becompatible with the new functions.

• Do not operate a 2 way remote control unit whenthe CONTROL A1 jacks are connected via a PCinterface kit to a personal computer running “MDEditor” or similar application. Also, do not operatethe connected component in a manner contrary tothe functions of the application, as this may causethe application to operate incorrectly.

continued

40GB

In the CONTROL A1 control system, thecontrol signals flow both ways, so there is nodistinction of IN and OUT jacks. If acomponent has more than one CONTROLA1 jack, you can use either one, or connectdifferent components to each jack.

On CONTROL A1 jacks andconnectionsIt is possible to make connections betweenCONTROL A1 and CONTROL A1 jacks.For details regarding particular connections orset up options, refer to the operatinginstructions supplied with the component(s).

About the connecting cordSome CONTROL A1 compatible componentsare supplied with a connecting cord as anaccessory. In this case, use the connecting cordfor your connection.

When using a commercially available cord, usea monaural mini-plug cord less than 2 meterslong, with no resistance (such as the SonyRK-G69HG).

Basic Functions

The CONTROL A1 functions will operate aslong as the component you want to operate isturned on, even if all of the other connectedcomponents are not turned on.

CONTROL A1

Jacks and connection examples

CONTROL A1 CD player

MD deck

Example

Amplifier(Receiver)

CDplayer

MDdeck

Tapedeck

Othercomponent

CONTROL A1 control system(continued)

CONTROL A1 and CONTROL A1compatibilityThe CONTROL A1 control system has beenupdated to the CONTROL A1 which is thestandard system in the Sony 300 disc CD changerand other recent Sony components. Componentswith CONTROL A1 jacks are compatible withcomponents with CONTROL A1 , and can beconnected to each other. Basically, the majority ofthe functions available with the CONTROL A1control system will be available with theCONTROL A1 control system.However, when making connections betweencomponents with CONTROL A1 jacks andcomponents with CONTROL A1 jacks, thenumber of functions that can be controlled may belimited depending on the component. For detailedinformation, refer to the operating instructionssupplied with the component(s).

Connections

Connect monaural mini-plug cords in series tothe CONTROL A1 jacks on the back of eachcomponent. You can connect up to 10CONTROL A1 compatible components inany order. However, you can connect only oneof each type of component (i.e., 1 CD player, 1MD deck, 1 tape deck and 1 receiver).

(You may be able to connect more than one CDplayer or MD deck, depending on the model.Refer to the operating instructions suppliedwith the respective component for details.)

Oth

er O

pe

ratio

ns

41GB

Automatic function selectionWhen you connect a CONTROL A1compatible Sony amplifier (or receiver) toother Sony components using monaural mini-plug cords, the function selector on theamplifier (or receiver) automatically switchesto the correct input when you press the playbutton on one of the connected components.

Notes• You must connect a CONTROL A1 compatible

amplifier (receiver) using a monaural mini-plugcord in order to take advantage of the automaticfunction selection feature.

• This function only works when the components areconnected to the amplifier (or receiver) inputsaccording to the names on the function buttons.Certain receivers allow you to switch the names ofthe function buttons. In this case, refer to theoperating instructions supplied with the receiver.

• When recording, do not play any components otherthan the recording source. It will cause theautomatic function selection to operate.

Synchronized recordingThis function lets you conduct synchronizedrecording between the selected source andrecorder components.

1 Set the function selector on theamplifier (or receiver) to the sourcecomponent.

2 Set the source component to pausemode (make sure both the N and Xindicators light together).

3 Set the recorder component to theREC-PAUSE mode.

4 Press PAUSE on the recordercomponent.The source component is released fromthe pause mode, and recording beginsshortly thereafter.When playback ends from the sourcecomponent, recording stops.

Notes• Do not set more than one component to the pause

mode.• Certain recorder components may be equipped with

a special synchronized recording function that usesthe CONTROL A1 Control System, such as“CD Synchro Dubbing”. In this case, refer to theoperating instructions supplied with the recordercomponent.

42GB

For models of area code U, CA onlyYou can use the remote RM-PP411 to operatethe components in your system.

Before you use yourremote

Inserting batteries into theremote

Insert R6 (size-AA) batteries with the + and –properly oriented in the battery compartment.When using the remote, point it at the remotesensor g on the receiver.

TipUnder normal conditions, the batteries should last forabout 6 months. When the remote no longer operatesthe receiver, replace all batteries with new ones.

Notes• Do not leave the remote in an extremely hot or

humid place.• Do not use a new battery with an old one.• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause amalfunction.

• If you don’t use the remote for an extended periodof time, remove the batteries to avoid possibledamage from battery leakage and corrosion.

Remote buttondescription

N X

m M

. >

-

VIDEO1 VIDEO2

USE MODE

SYSTEM STANDBY SLEEP

AV1 AV2

TV ?/1 AV ?/1

VIDEO3 DVD/LD

TV/SAT MD/TAPE CD/SACD TUNER

PHONO AUX MULTI CH SOURCE

SHIFT

TOP MENU/GUIDE AV MENU

MUTING

MASTERVOL

DISPLAY

TV VOL TV CH

WIDE ON SCREEN

TV/VIDEO

MAINMENU

RETURN/EXIT

D.TUNING DISC ALT

ANT CLEAR SEARCH MODE

TESTTONE PRESET

1 2 3

4 5 6

7 8 9

0/10 >10/11 12

AUTO DEC

SUBTITLE ENTER

MODE

AUDIOSWAP/ANGLE

JUMP/TIME

PRESET/CH/D.SKIP

MPX/DUAL

ANALOGDIRECT 2CH

SOUND FIELD

x

?/1P

Of

F

G g

Operations Using the Remote RM-PP411

The tables below show the settings of eachbutton.

Remote Operations FunctionButton

?/1 Receiver Turns the receiver on or off.

SLEEP Receiver Activates the sleepfunction and the durationwhich the receiver turnsoff automatically.

VIDEO 1 Receiver To watch VCR.(VTR mode 3)


ENTER/EXECUTE

Op

era

tion

s Usin

g th

e R

em

ote

RM

-PP

41

1

43GB

continued


V/v Receiver Select a menu item.

B/b Receiver Makes adjustment orchange the setting.

MASTER Receiver Adjusts the masterVOL +/– volume of the receiver.

MAIN Receiver Press this buttonMENU repeatedly to select one

of the five cursor modes:EQ, SURR, LEVEL,SET UP and NAME.

ON Receiver To display the menus ofSCREEN the receiver on the TV

screen.

AV ?/1 TV/VCR/ Turns the audio andCD player/ video components on orVCD player/ off.LD player/DVD player/MD deck/DAT deck

SYSTEM Receiver/TV/ Turns off the receiver andSTANDBY VCR/Satellite other Sony audio/video(Press tuner/CD components.AV ?/1 player/VCDand ?/1 player/LD player/at the DVD player/same time) MD deck/DAT

deck/Tape deck

1–9 and Receiver Use with “SHIFT” button0/10 to select tuner preset

station numeric inputduring DIRECTTUNING or MEMORYmode.

CD player/ Select track numbers. 0VCD player/ selects track 10.LD player/MD deck/DAT deck

TV/VCR/ Select channel numbers.Satellite tuner

>10/11 CD player/ Select track numbersVCD player/ over 10.LD player/MDdeck/Tape deck



DVD/LD Receiver To watch DVD or laserdisc.

TV/SAT Receiver To watch TV programsor satellite receiver.

MD/TAPE Receiver To listen to Minidiscor audio tape.

CD/SACD Receiver To listen to compact disc.

TUNER Receiver To listen to radioprograms.

PHONO Receiver To listen to turntable.

AUX Receiver To listen to an audioequipment.

MULTI CH Receiver Selects MULTI CH INsource.

TEST Receiver Press to output test tone.TONE

PRESET Receiver Selects preset sound field(e.g. Cinema StudioEX A, B, C).

AUTO DEC Receiver Selects AUTODECODING mode.

MPX/DUAL Receiver Select Dual Mono orBilingual sound of DolbyDigital, DTS or AAC, etc.

ANALOG Receiver Selects 2CH ANALOGDIRECT DIRECT.

2CH Receiver Selects 2CH mode.

MODE +/– Receiver Selects sound field mode.

SHIFT Receiver Press repeatedly to selecta memory page forpresetting radio stationsor tuning to presetstations.

D.TUNING Receiver Tuner station direct key-in-mode.

MUTING Receiver Mutes the sound from thereceiver.

44GB

Remote Button Description(continued)


AUDIO TV/ VCR/ Changes the sound toDVD player Multiplex, Bilingual or

Multi channel TV Sound.

SWAP*/ TV Swaps the small andANGLE large picture.

DVD player To select viewing angleor changes the angles.

JUMP/ TV Toggles between theTIME previous and the current

channels.

CD player/ Shows the time orVCD player/ displays the playing timeDVD player of disc, etc.

PRESET/ Receiver Scans and selects presetCH/ stations.

D.SKIP +/– TV/VCR/ Selects preset channels.satellite tuner

CD player/ Skips discs (multi-discVCD player/ changer only).DVD player/MD deck

ENTER TV/VCR/ After selecting a channel,satellite tuner/ disc or track using theLD player/ numeric buttons, press toMD deck/ enter the value.DAT deck/Tape deck

DISC CD player/ Selects a disc directlyVCD player (multi-disc changer

only).

ANT VCR Selects output signalfrom aerial terminal: TVsignal or VCR program.

./> VCR/ Skips tracks.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

* Only for Sony TVs with the picture-in-picturefunction.


m/M CD player/ Searches tracksVCD player/ (forward or backward).DVD player/LD player/MD deck

VCR/ Fastforwards orDAT deck/ rewinds.Tape deck

N VCR/ Starts play.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

X VCR/ Pauses play or record.CD player/ (Also starts recordingVCD player/ with components inLD player/ record standby.)DVD player/MD deck/DAT deck/Tape deck

x VCR/ Stops play.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

DISPLAY TV/VCR/ Selects informationVCD player/ displayed on the TVLD player/ screen.DVD player

RETURN/ VCD player/ Returns to the previousEXIT LD player/ menu.

DVD player

Satellite Exits the menu.tuner

SUBTITLE DVD player Changes the subtitles.

Op

era

tion

s Usin

g th

e R

em

ote

RM

-PP

41

1

45GB

Notes• Some functions explained in this section may not

work depending on the model of the receiver.• The above explanation is intended to serve as an

example only.Therefore, depending on the component the aboveoperation may not be possible or may operatedifferently than described.

• The TV/SAT, PHONO, SOURCE, MPX/DUAL,ANALOG DIRECT, 12 and ON SCREENfunctions are not available for set operation.

Selecting the mode of theremote

Set the remote mode using the USE MODEbutton and the remote mode buttons.

Selecting the command modeYou can switch the command mode (AV1 orAV2) of the remote. If the command mode ofthe receiver and the remote is different, youcannot use the remote to operate the receiver.

Press 1 (AV1) (or 2 (AV2)) while pressingdown USE MODE.The indicator lights once (twice for AV2) , thenthe command mode switches.

To check the mode of the remotePress USE MODE. You can check the remoteby the indicator.

Mode Indicator lights

AV1 once

AV2 twice

To reset the remote to factorysettings

Press =/1, AV =/1, and MASTER VOL – atthe same time.The indicator lights 3 times, then goes off.


CLEAR DVD player Press if you made amistake when you pressthe number button orpress to return to thecontinuous play etc.

SEARCH DVD player Select searching mode.MODE Press to select the unit for

search (track, index, etc.)

TOP MENU DVD player Displays DVD title./GUIDE

AV MENU VCR/Satellite/ Displays menu.tuner/DVD player

O VCD player/ Returns to the previousLD player/ menu or exits the menu.DVD player

V/v/B/b VCR/Satellite Selects a menu item.tuner/DVD player

ENTER/ VCR/satellite Press to enter theEXECUTE tuner/ selection.

DVD player

TV ?/1 TV Turns the TV on or off.

-/-- TV Selects the channelentry mode, either oneor two digit.

TV VOL TV Adjust the volume of the+/– TV.

TV CH +/– TV Select preset TVchannels.

TV/ TV Selects input signal: TVVIDEO input or video input.

WIDE TV Selects the wide picturemode.

USE MODE Remote To set up theremote.

AV1 and Remote Select the commandAV2 mode of the remote.

SOURCE Remote Selects 2ND AV output.

ALT Remote Change remote keyfunction to activate thosebuttons with orangeprinting.

46GB

Programming the remoteYou can program the remote to control non-Sony components by changing the code. Oncethe control signals have been memorized, youcan use those components as part of yoursystem.

Furthermore, you can also program the remotefor Sony components that the remote is unableto control. Note that the remote can onlycontrol components that accept infraredwireless control signals.

1 Press AV ?/1 while pressing down USEMODE.The indicator lights.

2 Press the function button (includingTV ?/1) for the component you want tocontrol.For example, if you are going to control aCD player, press CD/SACD.

3 Press the numeric buttons to enter thenumeric code (or one of the codes ifmore than one code exists)corresponding to the component andthe maker of the component you wantto control.See the tables on pages 47 and 48 forinformation on the numeric code(s)corresponding to the component and themaker of the component (the first digit andthe last two digits of the numeric codecorrespond to the category and the maker’scode respectively.)

4 Press ENTER.Once the numeric code has been verified,the indicator slowly flashes twice and theremote automatically exits the programmingmode.

5 Repeat steps 1 to 4 to control othercomponents.

To cancel programmingPress USE MODE during any step. The remoteautomatically exits the programming mode.

To activate the function afterprogramming.Press the programmed button to activate thefunction you want.

If programming is unsuccessful,check the following:• If the indicator does not light up in step 1, the

batteries are weak. Replace both batteries.• If the indicator flashes 4 times in quick succession

while entering the numeric code, an error hasoccurred. Start again from step 1.

Notes• The indicator turns off while a valid button is

pressed.• In step 2, if several function buttons are pressed,

only the last pressed button is valid.• In step 2, if you press TV ?/1, only TV VOL +/–,

TV CH +/–, TV/VIDEO and WIDE buttons arereprogrammed.

• In step 3, if a function button is pressed, the newfunction is selected and the programmingprocedure returns to the beginning of step 3.

• For the numeric codes, only the first three numbersentered are valid.

To clear the memory of the remoteTo clear all programmed and learned signals,do the following to reset the remote to factorysettings.

Press ?/1, AV ?/1 and MASTER VOL – atthe same time.The indicator flashes 3 times, then goes off.

Op

era

tion

s Usin

g th

e R

em

ote

RM

-PP

41

1

47GB

The numeric codes corresponding tothe component and the maker of thecomponent

Use the numeric codes in the tables below tocontrol non-Sony components and also Sonycomponents that the remote is normally unableto control. Since the remote signal that acomponent accepts differs depending on themodel and year of the component, more thanone numeric code may be assigned to acomponent. If you fail to program your remoteusing one of the codes, try using other codes.

Notes• The numeric codes are based on the latest

information available for each brand. There is achance, however, that your component will notrespond to some or all of the codes.

• All of the functions on this remote may not beavailable when used with your particularcomponent.

To control a CD player

Maker Code(s)

SONY 101, 102, 103

DENON 104, 123

JVC 105, 106, 107

KENWOOD 108, 109, 110

MAGNAVOX 111, 116

MARANTZ 116

ONKYO 112, 113, 114

PANASONIC 115

PHILIPS 116

PIONEER 117

TECHNICS 115, 118, 119

YAMAHA 120, 121, 122

To control a DAT deck

Maker Code(s)

SONY 203

PIONEER 219

To control an MD deck

Maker Code(s)

SONY 301

DENON 302

JVC 303

KENWOOD 304

To control a tape deck

Maker Code(s)

SONY 201, 202

DENON 204, 205

KENWOOD 206, 207, 208, 209

NAKAMICHI 210

PANASONIC 216

PHILIPS 211, 212

PIONEER 213, 214

TECHNICS 215, 216

YAMAHA 217, 218

To control an LD player

Maker Code(s)

SONY 601, 602, 603

PIONEER 606

To control a video CD player

Maker Code(s)

SONY 605

continued

48GB

To control a VCR

Maker Code(s)

SONY 701, 702, 703, 704, 705,706

AIWA 710, 750, 757, 758

AKAI 707, 708, 709, 759

BLAUPUNKT 740

EMERSON 711, 712, 713, 714, 715,716, 750

FISHER 717, 718, 719, 720

GENERAL ELECTRIC 721, 722, 730

GOLDSTAR 723, 753

GRUNDIG 724

HITACHI 722, 725, 729, 741

ITT/NOKIA 717

JVC 726, 727, 728, 736

MAGNAVOX 730, 731, 738

MITSUBISHI/MGA 732, 733, 734, 735

NEC 736

PANASONIC 729, 730, 737, 738, 739,740

PHILIPS 729, 730, 731

PIONEER 729

RCA/PROSCAN 722, 729, 730, 731, 741,747

SAMSUNG 742, 743, 744, 745

SANYO 717, 720, 746

SHARP 748, 749

TELEFUNKEN 751, 752

TOSHIBA 747, 755, 756

ZENITH 754

To control a DVD player

Maker Code(s)

SONY 401, 402, 403

PANASONIC 406, 408

PHILIPS 407

PIONEER 409

TOSHIBA 404

DENON 405

To control a TV

Maker Code(s)

SONY 501

DAEWOO 504, 505, 506, 507, 515,544

FISHER 508

GOLDSTAR 503, 511, 512, 515, 534,544

GRUNDIG 517, 534

HITACHI 513, 514, 515, 544

ITT/NOKIA 521, 522

JVC 516

MAGNAVOX 503, 518, 544

MITSUBISHI/MGA 503, 519, 544

NEC 503, 520, 544

PANASONIC 509, 524

PHILIPS 515, 518

PIONEER 509, 525, 526, 540

RCA/PROSCAN 510, 527, 528, 529, 544

SAMSUNG 503, 515, 531, 532, 533,534, 544

SANYO 508, 545

SHARP 535

TELEFUNKEN 523, 536, 537, 538

THOMSON 530, 537, 539

TOSHIBA 535, 540, 541

ZENITH 542, 543

To control a satellite tuner or cablebox

Maker Code(s)

SONY 801, 802

JERROLD/G.I. 806, 807, 808, 809, 810,811, 812, 813, 814

PANASONIC 818

RCA 805, 819

S. ATLANTA 815, 816, 817

Programming the remote (continued)

Op

era

tion

s Usin

g th

e R

em

ote

RM

-U3

05

C

49GB

Except for models of area code U,CAYou can use the remote RM-U305C to operatethe components in your system.

Before you use yourremote

Inserting batteries into theremote

Insert R6 (size-AA) batteries with the + and –properly oriented in the battery compartment.When using the remote, point it at the remotesensor g on the receiver.

TipUnder normal conditions, the batteries should last forabout 6 months. When the remote no longer operatesthe receiver, replace all batteries with new ones.

Notes• Do not leave the remote in an extremely hot or

humid place.• Do not use a new battery with an old one.• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause amalfunction.

• If you don’t use the remote for an extended periodof time, remove the batteries to avoid possibledamage from battery leakage and corrosion.

Remote buttondescription

P p

DISC9 (

0 )

= +

>10 0

7 8 9

4 5 6

1 2 3

ENTER

CD/SACD TUNER

VIDEO

AUX

MD/TAPE

VIDEO 2

PHONO

VIDEO 1 VIDEO 3

SYSTEMSTANDBY

FUNCTION

SHIFT

POSITION

DISPLAY

MODE

JUMP

A.DEC

– MUTING

2CH/OFF

WIDE

P IN P

SWAP

D.SKIP/CH/PRESET

– /– –

– SUB CH +

ANTTV/VTR

TV/VIDEO

MULTI/2CHA. DIRECT

SOUND FIELD

+

MAIN MENU

MENU

MASTERVOLTEST TONE

D.TUNING

RETURN

MENU

ENTER

TITLEf

F

G g

SLEEPAV

?/1 ?/1

DVD/LD TV/SAT

FN SHIFT

]

]

Operations Using the Remote RM-U305C

continued

The tables below show the settings of eachbutton.


SLEEP Receiver Activates the sleepfunction and the durationwhich the receiver turnsoff automatically.

?/1 Receiver Turns the receiver on oroff.

50GB

Remote button description(continued)


TEST Receiver Press to output test tone.TONE

MAIN Receiver Press this buttonMENU repeatedly to select one

of the five cursor modes:EQ, SURR, LEVEL,SET UP and NAME.

MENU </> Receiver Selects a menu item.

MENU +/– Receiver Makes adjustment orchange the setting.

MASTER Receiver Adjusts the masterVOL +/– volume of the receiver.

AV ?/1 TV/VCR/ Turns the audio andCD player/ video components on orVCD player/ off.LD player/DVD playerMD deck/DAT deck/

SYSTEM Receiver/TV/ Turns off the receiver andSTANDBY VCR/Satellite other Sony audio/video(Press AV tuner/ components?/1 and CD player/?/1 at VCD player/the same LD player/time) DVD player/

MD deck/DAT deck/TAPE deck.

0-9 Receiver Use with “SHIFT” buttonto select tuner presetstation numeric inputduring DIRECTTUNING or MEMORYmode.

CD player/ Selects track numbers.VCD player/ 0 selects track 10.LD player/MD deck/DAT deck

TV/VCR/ Selects channel numbers.satellite tuner

>10 CD player/ Selects tracks numbersVCD player/ over 10.LD player/MD deck/Tape deck


VIDEO/ Receiver To watch VCR.VIDEO 1* (VTR mode 3)

VIDEO 2* Receiver To watch VCR.(VTR mode 1)

VIDEO 3* Receiver To watch VCR.(VTR mode 2)

DVD/LD Receiver To watch DVD or laserdisc.

TV/SAT Receiver To watch TV programsor satellite receiver.

PHONO* Receiver To listen to turntable.

MD/TAPE*Receiver To listen to Minidisc oraudio tape.

AUX Receiver To listen to an audioequipment.

CD/SACD Receiver To listen to compact disc.

TUNER Receiver To listen to radioprograms.

SHIFT Receiver Press repeatedly to selecta memory page forpresetting radio stationsor tuning to presetstations.

D.TUNING Receiver Tuner station direct key-in-mode.

A.DEC Receiver Select AUTODECODING mode.

MODE+/– Receiver Selects sound field mode.

2CH/OFF Receiver Turns off sound field orselect 2CH mode.

MULTI/ 2CH Receiver Selects MULTI CH INA. DIRECT source.

MUTING Receiver Mutes the sound from thereceiver

* VIDEO 1, VIDEO 2, VIDEO 3, PHONO andMD/TAPE function is a 2-key operation. To selectthe above function, press FN SHIFT (functionshift) and the function key you wantsimultaneously. For example, press FN SHIFT andCD/SACD to select MD/TAPE function.

Op

era

tion

s Usin

g th

e R

em

ote

RM

-U3

05

C

51GB


X VCR/ Pauses play or record.CD player/ (Also start recordingVCD player/ with components inLD player/ record standby.)DVD player/MD deck/DAT deck/Tape deck

x VCR/ Stops play.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

DISPLAY TV/VCR, Selects informationVCD player/ displayed on the TVLD player/ screen.DVD player

ANT VCR Selects output signalTV/VTR from the aerial terminal:

TV signal or VCRprogram.

DISC CD player Select discs (multi-discchanger only).

TOP DVD player Displays DVD title.MENU

DVD DVD player Displays DVD menu.MENU

ENTER DVD player Enters the selection.

RETURN DVD player Returns to previous menuor exits the menu.

V/v/B/b DVD player Selects a menu item.

÷ TV Selects the channel entrymode, either one or twodigit


ENTER TV/VCR/ After selecting a channel,satellite tuner/ disc or track using theLD player/ numeric buttons, press toMD deck/ enter the value.DAT deck/Tape deck

D. SKIP/ Receiver Scans and selects presetCH/PRESET stations.+/-

TV/VCR/ Selects preset channel.satellite tuner

CD player/ Skips discs (multi-discVCD player/ changer only).DVD player/MD deck

./> VCR/ Skip tracks.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

m/M CD player/ Search tracks (forward orVCD player/ backward)DVD player

VCR/ Fastforwards or rewinds.LD player/MD deck/DAT deck/Tape deck

n Tape deck Starts play on the reverseside.

N VCR/ Starts play.CD player/VCD player/LD player/DVD player/MD deck/DAT deck/Tape deck

continued

52GB


POSITION**TV Changes the position ofthe small picture.

SWAP** TV Swaps the small and thelarge picture.

SUB CH TV Selects the preset+/–** channels for the small

picture.

P IN P** TV Activates the picture-in-picture function.

JUMP TV Toggles between theprevious and the currentchannels.

WIDE TV Selects the wide picturemode.

TV/VIDEO TV Selects input signal: TVinput or video input.

** Only for Sony TVs with the picture-in-picturefunction.

Notes• When you press the function buttons (VIDEO 1,

VIDEO 2, VIDEO 3, DVD/LD), the input mode ofthe TV might not switch to the corresponding inputmode that you want. In this case, press the TV/VIDEO button to switch the input mode of the TV.

• Some functions explained in this section may notwork depending on the model of the receiver.

• The above explanation is intended to serve as anexample only. Therefore, depending on thecomponent the above operation may not be possibleor may operate differently than described.

• The TV/SAT and PHONO functions are notavailable for set operation.

Changing the factorysetting of a function button

If the factory settings of the FUNCTIONbuttons do not match your system components,you can change them. For example, if you havean MD player and a tape deck and you don’thave a CD player, you can assign the CD/SACDbutton to your tape deck.

Note that the settings of the TUNER andFN SHIFT functions (VIDEO 1, VIDEO 2,VIDEO 3, PHONO and MD/TAPE) buttoncannot be changed.

1 Hold down the Function button whosefunction you want to change (forexample, CD/SACD).

2 Press the corresponding button of thecomponent you want to assign to theFunction button (for example, 4 – Tapedeck).The following buttons are assigned to selectthe functions:

To operate Press

CD player 1

DAT deck 2

MD deck 3

Tape deck A 4

Tape deck B 5

LD player 6

VCR (command mode VTR 1*) 7



TV 0

DSS (Digital Satellite Receiver) >10

DVD ENTER

VCD player .

* Sony VCRs are operated with a VTR 1, 2 or 3setting. These correspond to Beta, 8mm andVHS respectively.

Now you can use the CD/SACD button tocontrol the tape deck.

To reset a button to its factorysettingRepeat the above procedure.

To reset all the function buttons totheir factory settingPress ?/1, AV ?/1 and MASTER VOL – atthe same time.

Remote button description(continued)

Ad

ditio

na

l Info

rma

tion

53GB

Additional InformationIf you have any question or problem concerning yourreceiver, please consult your nearest Sony dealer.

TroubleshootingIf you experience any of the followingdifficulties while using the receiver, use thistroubleshooting guide to help you remedy theproblem. Also, see “Checking the connections”on page 22 to verify that the connections arecorrect. Should any problem persist, consultyour nearest Sony dealer.

There is no sound or only a very low-level soundno matter which component is selected.

• Check that the speakers and components areconnected securely and correctly.

• Check that both the receiver and all thecomponents are turned on.

• Check that the MASTER VOLUME control isnot set at VOL MIN.

• Check that the SPEAKERS A/B button is not setto “SP. OFF” and is set accordingly to yourSPEAKERS FRONT system (page 24).

• Press MUTING to cancel the muting function.• Check that the headphones are not connected.• The protective device on the receiver has been

activated because of a short circuit (“PROTECT”flashes). Turn off the receiver, eliminate theshort-circuit problem and turn on the poweragain.

There is no sound from a specific component.

• Check that the component is connected correctlyto the audio input jacks for that component.

• Check that the cord(s) used for the connection is(are) fully inserted into the jacks on both thereceiver and the component.

• Check that you have selected the correctcomponent on the receiver.

continued

Precautions

On safetyShould any solid object or liquid fall into the cabinet,unplug the receiver and have it checked by qualifiedpersonnel before operating it any further.

On power sources• Before operating the unit, check that the operating

voltage is identical with your local power supply.The operating voltage is indicated on the nameplateat the rear of the receiver.

• The unit is not disconnected from the AC powersource (mains) as long as it is connected to the walloutlet, even if the receiver itself has been turned off.

• If you are not going to use the receiver for a longtime, be sure to disconnect the receiver from thewall outlet. To disconnect the AC power cord,grasp the plug itself; never pull the cord.

• (Models of area code U, CA only)One blade of the plug is wider than the other for thepurpose of safety and will fit into the wall outletonly one way. If you are unable to insert the plugfully into the outlet, contact your dealer.

• AC power cord must be changed only at thequalified service shop.

On heat buildupAlthough the unit heats up during operation, this isnot a malfunction. If you continuously use this unit ata large volume, the cabinet temperature of the top,side and bottom rises considerably. To avoid burningyourself, do not touch the cabinet.

On placement• Place the receiver in a location with adequate

ventilation to prevent heat buildup and prolong thelife of the receiver.

• Do not place the receiver near heat sources, or in aplace subject to direct sunlight, excessive dust ormechanical shock.

• Do not place anything on top of the cabinet thatmight block the ventilation holes and causemalfunctions.

On operationBefore connecting other components, be sure to turnoff and unplug the receiver.

On cleaningClean the cabinet, panel and controls with a soft clothslightly moistened with a mild detergent solution. Donot use any type of abrasive pad, scouring powder orsolvent such as alcohol or benzine.

54GB

Troubleshooting (continued) There is no sound from the active sub woofer.

There is no sound output from the SUB WOOFERterminal depending on the sound field (back page).

The surround effect cannot be obtained.

Make sure the sound field function is on (pressMODE).

Dolby Digital or DTS multi channel sound is notreproduced.

• Check that the playing DVD, etc. is recorded inDolby Digital or DTS format.

• When connecting the DVD player, etc. to thedigital input jacks of this receiver, check theaudio setting (settings for the audio output) of theconnected component.

Recording cannot be done.

• Check that the components are connectedcorrectly.

• Select the source component with functionbuttons.

• Make sure that INPUT MODE is set to“ANALOG” before recording from a digitalcomponent connected to the analog MD/TAPEterminals.

• Make sure that INPUT MODE is set to “COAXIN” or “OPT IN” (page 23) before recordingfrom a digital component connected to theDIGITAL MD/TAPE OUT terminals.

To connect an LD player via an RF demodulator.

Connect the LD player to the RF demodulator,then connect the RF demodulator’s optical orcoaxial digital output to the receiver’s jack. Whenmaking this connection, be sure to set INPUTMODE manually (page 23). The receiver may notoperate correctly if INPUT MODE is set to“AUTO IN”.For details on DOLBY DIGITAL RF hookups, seethe operating instructions supplied with your RFdemodulator.

There is no sound from one of the frontspeakers.

Connect a pair of headphones to the PHONES jackto verify that sound is output from the headphones(page 24).If only one channel is output from the headphones,the component may not be connected to thereceiver correctly. Check that all the cords are fullyinserted into the jacks on both the receiver and thecomponent.If both channels are output from the headphones,the front speaker may not be connected to thereceiver correctly. Check the connection of thefront speaker which is not outputting any sound.

The left and right sounds are unbalanced orreversed.

• Check that the speakers and components areconnected correctly and securely.

• Adjust balance parameters in the LEVEL menu.

There is severe hum or noise.

• Check that the speakers and components areconnected securely.

• Check that the connecting cords are away from atransformer or motor, and at least 3 meters awayfrom a TV set or fluorescent light.

• Move your TV away from the audio components.• The plugs and jacks are dirty. Wipe them with a

cloth slightly moistened with alcohol.

There is no sound or only a very low-level soundis heard from the center or/and surroundspeakers.

• Make sure the sound field function is on (pressMODE).

• Select a sound field containing the word“C.ST.EX” (pages 25–26).

• Adjust the speaker level (page 22).• Make sure the center or/and surround speaker

size parameter is set to either “SMALL” or“LARGE” (page 19).

Ad

ditio

na

l Info

rma

tion

55GB

Outdoor FM antennaReceiver

Ground wire(not supplied)

To ground

ANTENNA

AM

COAXIAL

FM75Ω

The FM reception is poor.

Use a 75-ohm coaxial cable (not supplied) toconnect the receiver to an outdoor FM antenna asshown below. If you connect the receiver to anoutdoor antenna, ground it against lightning. Toprevent a gas explosion, do not connect the groundwire to a gas pipe.

Radio stations cannot be tuned in.

• Check that the antennas are connected securely.Adjust the antennas and connect an externalantenna if necessary.

• The signal strength of the stations is too weak(when tuning in with automatic tuning). Usedirect tuning.

• Make sure you set the tuning interval correctly(when tuning in AM stations with direct tuning).

• No stations have been preset or the presetstations have been cleared (when tuning byscanning preset stations). Preset the stations(page 34).

• Press DISPLAY so that the frequency appears inthe display.

RDS does not work.*

• Make sure that you’re tuned to an FM RDSstation.

• Select a stronger FM station.

The RDS information that you want does notappear.*

Contact the radio station and find out whether theyactually provide the service in question. If so, theservice may be temporarily out of order.

There is no picture or an unclear picture appearson the TV screen or monitor.

• Select the appropriate function on the receiver.• Set your TV to the appropriate input mode.• Move your TV away from the audio components.

The remote does not function.

• The TV/SAT, PHONO, SOURCE, MPX/DUAL,ANALOG DIRECT, 12 and ON SCREENbuttons on the remote are not available.(RM-PP411 only)

• The TV/SAT and PHONO buttons on the remoteare not available. (RM-U305C only)

• Point the remote at the remote sensor g on thereceiver.

• Check that the mode of the remote correspondsto that of the receiver (pages 38 and 45)(RM-PP411 only).

• Check that you select AV1 as the commandmode of the receiver (page 38) (RM-U305Conly).

• Remove any obstacles in the path between theremote and the receiver.

• Replace both batteries in the remote with newones, if they are weak.

• Make sure you select the correct function on theremote.

• If the remote is set to operate the TV only, usethe remote to select a source or component otherthan TV before operating the receiver or othercomponent.

• Press MAIN MENU on the remote before youuse the V/v/B/b buttons for receiver operation(RM-PP411 only).

* Models of area code CEL, CEK only.

Clearing the receiver’s memory

To clear See

All memorized settings page 17

Customized sound fields page 31

56GB

Area code Power requirements

E2/E3, AU 240 V AC, 50 Hz

SP, CEL, CEK, AR 230 V AC, 50 Hz

TW 110 V AC, 60 Hz

MX 120 V AC, 60 Hz

Frequency response

MULTI CH IN,CD/SACD, AUX,MD/TAPE, DVD/LD,VIDEO 1, 2, 3

Inputs (Analog)

MULTI CH IN,CD/SACD, AUX,MD/TAPE, DVD/LD,VIDEO 1, 2, 3

3) INPUT SHORT (with sound field, equalizer andbass boost bypassed).

4) Weighted network, input level.

Inputs (Digital)

DVD/LD (Coaxial) Sensitivity: –Impedance: 75 ohmsS/N: 100 dB(A, 20 kHz LPF)

VIDEO 2, CD/SACD, Sensitivity: –MD/TAPE (Optical) Impedance: –

S/N: 100 dB(A, 20 kHz LPF)

Outputs (Analog)MD/TAPE (OUT), Voltage: 250 mVVIDEO 1 (AUDIO OUT) Impedance: 10 kilohms

SUB WOOFER Voltage: 2 VImpedance: 1 kilohms

Outputs (Digital)

MD/TAPE (Optical) Sensitivity: –

EQGain levels: ±6 dB, 1 dB step

10 Hz – 70 kHz+0.5/–2 dB (with soundfield, equalizer, and bassboost bypassed)

Sensitivity: 250 mVImpedance: 50 kilohmsS/N3): 96 dB(A, 250 mV4))

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTALHARMONIC DISTORTION:

With 8 ohm loads, both channels driven, from20 – 20,000 Hz; rated 100 watts per channelminimum RMS power, with no more than0.09 % total harmonic distortion from 250milliwatts to rated output (Models of area codeU only).

Amplifier sectionPOWER OUTPUTModels of area code U, CARated Power Output at Stereo Mode(8 ohms 20 Hz – 20 kHz, THD 0.09 %)

100 W + 100 W

Reference Power Output(8 ohms 1 kHz, THD 0.7 %)FRONT1): 100 W/chCENTER1): 100 WSURR1): 100 W/ch

Models of area code CEL, CEKRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)

100 W + 100 W2)

Reference Power Output2)

(8 ohms 1 kHz, THD 0.7 %)FRONT1): 100 W/chCENTER1): 100 WSURR1): 100 W/ch

Models of other area codeRated Power Output at Stereo Mode(8 ohms 1 kHz, THD 0.7 %)

100 W + 100 W2)

Reference Power Output2)

(8 ohms 1 kHz, THD 10 %)FRONT1): 120 W/chCENTER1): 120 WSURR1): 120 W/ch

1) Depending on the sound field settings and thesource, there may be no sound output.

2) Measured under the following conditions:

Ad

ditio

na

l Info

rma

tion

57GB

FM tuner sectionTuning range 87.5 - 108.0 MHz

Antenna terminals 75 ohms, unbalanced

Intermediate frequency10.7 MHz

SensitivityMono: 18.3 dBf, 2.2 µV/75 ohmsStereo: 38.3 dBf, 22.5 µV/75 ohms

Usable sensitivity 11.2 dBf, 1 µV/75 ohms

S/NMono: 76 dBStereo: 70 dB

Harmonic distortion at 1 kHzMono: 0.3%Stereo: 0.5%

Separation 45 dB at 1 kHz

Frequency response 30 Hz – 15 kHz,+0.5/–2 dB

Selectivity 60 dB at 400 kHz

AM tuner sectionTuning rangeModels of area code U, CAWith 10-kHz tuning scale: 530 – 1710 kHz5)

With 9-kHz tuning scale: 531 – 1710 kHz5)

Models of area code E2/E3, AR, MXWith 10-kHz tuning scale: 530 – 1610 kHz5)

With 9-kHz tuning scale: 531 – 1602 kHz5)

Models of area code SP, CEL, CEK, TW, AUWith 9-kHz tuning scale: 531 – 1602 kHz

Antenna Loop antenna

Intermediate frequency450 kHz

Usable sensitivity 50 dB/m (at 1,000 kHz or999 kHz)

S/N 54 dB (at 50 mV/m)

Harmonic distortion 0.5 % (50 mV/m, 400 Hz)

SelectivityAt 9 kHz: 35 dBAt 10 kHz: 40 dB

5) You can change the AM tuning scale to 9 kHz or10 kHz. After tuning in any AM station, turn offthe receiver. Hold down PRESET TUNING + andpress ?/1. All preset stations will be erased whenyou change the tuning scale. To reset the scale to10 kHz (or 9 kHz), repeat the procedure.

Video sectionInputsVideo: 1 Vp-p, 75 ohmsS-video: Y: 1 Vp-p, 75 ohms

C: 0.286 Vp-p, 75 ohmsComponent Video: Y: 1 Vp-p, 75 ohms

PB B-Y: 0.7 Vp-p,75 ohmsPR R-Y: 0.7 Vp-p,75 ohms

OutputsVideo: 1 Vp-p, 75 ohmsS-video: Y: 1 Vp-p, 75 ohms

C: 0.286 Vp-p, 75 ohmsComponent Video: Y: 1 Vp-p, 75 ohms

PB B-Y: 0.7 Vp-p,75 ohmsPR R-Y: 0.7 Vp-p,75 ohms

GeneralPower requirements

Area code Power requirements

U, CA, MX 120 V AC, 60 Hz

CEL, CEK 230 V AC, 50/60 Hz

SP, AR 220 – 230 V AC, 50/60 Hz

E2/E3 120/220/240 V AC, 50/60 Hz

TW 110 V AC, 50/60 Hz

AU 240 V AC, 50 Hz

Power consumption

Area code Power consumption

U, MX 210 W

CA 300 VA

CEL, CEK, AU, 180 WE2/E3, SP, AR

TW 450 W

Power consumption (during standby mode)0.5 W (when “A.PWR” in the SET UP menu is set to“NO”) (page 38).

continued

58GB

Specifications (continued)

AC outlets

Area code AC outlets

U, CA 1 switched, 120 W/1A MAX

SP, CEL, CEK, 1 switched, 100 W MAXE2/E3, TW, AU,MX

Dimensions 430 × 157.5 × 308.5 mm(16 7/8 × 6 2/8 × 12 1/8inches) includingprojecting parts andcontrols

Mass (Approx.) 7.5 kg (16 lb 9 oz)

Supplied accessoriesFM wire antenna (1)AM loop antenna (1)Remote commander (1)

• RM-PP411 (models of area code U, CA only)• RM-U305C (except for models of area code U,

CA)R6 (size-AA) batteries (2)

For details on the area code of the component youare using, see page 4.

Design and specifications are subject to changewithout notice.

Ad

ditio

na

l Info

rma

tion

59GB

Tables of settings using SURR, LEVEL, EQ, and SET UPbuttons

You can make various settings using the LEVEL, SURR, EQ, SET UP buttons, jog dial, and / buttons. The tables below show each of the settings that these buttons can make.

Press Press or to select Turn jog dial to select Page

SURR EFFECT depends on the sound field (15 steps) 29

LEVEL L R BAL. L/R XXX L +8 to R +8 (1 steps) 29

CTR XXX dB –10 dB to +10 dB (1 dB steps)

SUR.L.XXX dB –10 dB to +10 dB (1 dB steps)

SUR.R.XXX dB –10 dB to +10 dB (1 dB steps)

S.W. XXX dB –10 dB to +10 dB (1 dB steps)

L.F.E. XXX dB OFF, –20 dB to 0 dB (1 dB steps)

D. RANGE COMP. XXX OFF, 0.1 to 0.9 (0.1 steps), STD, MAX

EQ FRONT BASS GAIN –6 dB to +6 dB (1 dB steps) 31

FRONT TREBLE GAIN –6 dB to +6 dB (1 dB steps)

SET UP L R (FRONT) LARGE, SMALL 18

C (CENTER) LARGE, SMALL, NO

SL SR (SURROUND) LARGE, SMALL, NO

SW (SUB WOOFER) S.W. XXX YES, NO

L R DIST. XX.X m between 1.0 meters and 12.0 meters(0.1 meters steps)1)

C DIST. XX.X m between L R DIST. and 1.5 meters(0.1 meters steps)2)

SL SR DIST. XX.X m between L R DIST. and 4.5 meters(0.1 meters steps)3)

SL SR PL. XXX SIDE, MID, BEHD.

SL SR HGT. XXX LOW, HIGH

C.MODE.AVX AV1, AV2 38

PRO LOGIC DOLBY PL, II MOVIE, II MUSIC

A.PWR–XXX YES, NO

1) For models of area code U, CA: between 3 feet and 40 feet (1 foot steps)2) For models of area code U, CA: between L R DIST. and 5 feet (1 foot steps)

3) For models of area code U, CA: between L R DIST. and 15 feet (1 foot steps)

Sony Corporation Printed in Malaysia

< LEVEL >

FRONT CENTER SUR.L. SUR.R. S. WOOFER LFE D.RANGEBAL LEVEL LEVEL LEVEL LEVEL MIX1) COMP1)

2CH ST. z z z

AUTO DEC. z z z z z z z

NORM.SURR. z z z z z z z

C.ST.EX A z z z z z z z

C.ST.EX B z z z z z z z

C.ST.EX C z z z z z z z

HALL z z z z z2) z z

JAZZ z z z z z2) z z

CONCERT z z z z z2) z z

GAME z z z z z z z

MULTI CH IN z z z z z

PCM96K z

1) These parameters may not operate depending on the source or adjustments. For details, see each item in“Adjusting the level parameters” (page 29).

2) When these sound fields are selected, there is no sound output from the sub woofer if the front speaker size is setto “LARGE”. However, sound will be output from the sub woofer if the digital input signal contains L.F.E.signals.

< SURR > < EQ >

< FRONT >EFFECT BASS TREBLELEVEL GAIN GAIN

2CH ST. z z

AUTO DEC. z z

NORM.SURR. z z

C.ST.EX A z z z

C.ST.EX B z z z

C.ST.EX C z z z

HALL z z z

JAZZ z z z

CONCERT z z z

GAME z z z

MULTI CH IN

PCM96K

Adjustable parameters for each sound fieldThe adjusted SURR and EQ parameters are stored in each sound field.

The adjusted LEVEL parameters are applied to all the sound fields.

FM Stereo FM-AM Receiver - Sony · FM Stereo FM-AM Receiver 4-238-379-12(1) STR-DE685 Owner’s...

Documents

Transcript of FM Stereo FM-AM Receiver - Sony · FM Stereo FM-AM Receiver 4-238-379-12(1) STR-DE685 Owner’s...