Floor Standing Bath Filler & Shower - Decina › wp-content › uploads › 2017 › 07 ›...
Transcript of Floor Standing Bath Filler & Shower - Decina › wp-content › uploads › 2017 › 07 ›...
As the bath filler can rotate 360 on the embedded box, no rotational alignment is required on the embedded box.
1. Prepare floor Concrete Floor: Cut down to a depth of 45 - 75mm below the finished floor
level.Wooden Floor: Construct a solid subfloor 45 - 75mm below the finished floor level.
2. Connect hot and cold pipes.
3. Bolt the embedded box into position.
4. Test to ensure box is level and shim if necessary.
5. Flush pipes and test that all connections are watertight.
6. When the floor is finished, trim the plastic skirt of the embedded box to floor level.
7. Fit the cover plate to the body
8. Fit the base nut to the body
9. Fit the base joint to the base nut.
10. Remove the white protective cover from the embedded box and bolt the bath filler to the embedded box.
11. Fit the shower head and hose.
12. Test to ensure all connections are watertight.
13. Slide cover plate into position to finish.
Floor Standing Bath Filler & Hand Shower
COVER PLATE
WASHER
PCW 9 FLOW CONTROL
SHOWER HEAD
LOWER BODY
METAL HOSE
WASHER
MIXER BODY
HANDLE
CARTRIDGE
TOP COVERRETAINING RING
TOP COVERCARTRIDGE NUT
MOUNTING BASE
1 WAY VALVE1 WAY VALVE HOUSINGSHOWER
HEAD HOLDER
DIVERTOR(Push up to divert)
o
EMBEDDED BOX
BASE JOINT
BASE NUT
RAW BOLTS
INSTALLATION INSTRUCTIONSInstallation should be to AS/NZS 3500 and by licenced Plumber
DEC 9
FLOOR STANDING FILLER/SHOWER
FOR WARRANTY PURPOSES.
Temperature and Pressure LimitsWarranty Document
The warranty is transferable but the original proof of purchase from an authorised Decina distributor is required for all claims.
Decina’s liability will not extend to damage caused by reasonably foreseeable loss such as inappropriate materials in a wet area ie. floating wooden floors.
Waterlines to tapware incorporating a ceramic cartridge or ceramic disc mechanism should have an inline strainer or filter fitted. Absence of these may void the warranty.
Any suspected defect must be notified to Decina as soon as possible after discovery. All repair work must be performed by a plumber who has received authorisation from Decina prior to proceeding with the work. Decina may immediately authorise repair work to be undertaken, however, this is not necessarily acceptance of liability.
Decina guarantee that the tapware will be able to handle temperatures up to a maximum of 80°C.
Water pressure up to 1000 kPa is the maximum limit for the tapware. Above this the warranty will become void.
DECINA OFFERS THE FOLLOWING WARRANTY PERIODS ON ITSRANGE OF AQUATICA TAPWARE FROM THE DATE OF PURCHASE.
A copy of the product label and testing sticker is provided here for easy
reference, should you ever need to talk to us
about your product
THE PROPERTY OWNER:
DON’T PANIC! A trace of water in the box is normal, as a result of final testing.
STEPHEN BREWSTERCEO
INSTALLATIONFor shower mixers the recommended backset is 60mm (check label for exact range). Hot left hand side. Cold right hand side. Outlet up. For sink and basin mixers, the most common mounting hole size is 34mm; for gooseneck sink mixers the hole size is 38mm. However, always check by measuring the product first. (Please ensure that you select the correct mounting hole size so that the o-ring can seal correctly to the mounted surface, ie. hole should be smaller than o-ring).
For cold water pressures above 600 kPa we recommend the installation of a pressure limiting valve.
• Recommended Operational Pressure Range: 50 - 600 kPa
• Maximum Operating Temp: 80°C Never to Exceed: 1000 kPa
Care and Maintenance
To retain the original look of your tapware, the following guidelines should be observed:
• Do not use acidic or abrasive detergents, spray cleaners, rough sponges or metallic cleaning pads.
• Do not use alcohol based products, disinfectants or solvents.
• To remove dirt or calcium, clean with mild detergent and water, then thoroughly rinse with clean water and dry with a clean soft cloth.
The use of spray or abrasive cleaners of any kind will void the warranty.
DECINA NATIONAL OFFICE – QLD
99 Cobalt StreetCAROLE PARK, QLD 4300
P: (07) 3271 1944F: (07) 3879 4244
Serial numbers or tags should not be removed from the products as they are essential in establishing warranty.
TAPWARE SPRAY HEADS, HOSESSHOWER ROSES &
SHOWER SETS
COMMERCIAL USE
Only high quality workmanship and materials have been used in the manufacture of Decina’s tapware. If any workmanship or material is proven faulty during the warranty period, Decina will, at its own option, repair or replace the faulty product.
About the Warranty
The ceramic cartridge used in Aquatica mixers has a 15 year replacement warranty. If a fault occurs during the first 12 months from purchase, the part will be replaced on site. Other parts carry a 7 year replacement warranty. There is no on site warranty for shower heads, pull out spray hoses and spray heads but they carry a 2 year replacement parts warranty. Other working parts that fail during the first 12 months will be replaced on site. The finish on powder coated tapware carries a 2 year warranty. The use of spray or abrasive cleaners will dull the finish and void the warranty.
CARTRIDGES
Thanks for taking the time to read this. Thanks also for your contribution to our success in business.
Now before you throw this in the drawer, attach your receipt to it - just in case . . .
PLEASE RETAIN THIS DOCUMENT,
TOGETHER WITH THE RECEIPT,