EnigmaPocket sliding door systems

Fire rating:

NFRFrame type:

Shadow gap

21 Installation instructionsNFR S

Enigma Pocket sliding door systems

Thank you for choosing EnigmaTo ensure the installation process is simple and efficient we recommended you read this guide in full before you begin.

Tools required

To install your Enigma doorset you will

need the following tools:

Tape measure

Pin hammer

Set square

Allen keys (metric)

Spirit levelPencil

Knife

Tin snips or hacksaw

Cordless screwdriver

Getting started

The Enigma pocket door kit will be delivered

flat-packed in a box as shown. It will include all

components including fixings.

If a door leaf is ordered this will come separately.

Preparing for installation

Before installation, please ensure the system specifications correspond with your project schedule.

3

Power chop saw

Enigma Pocket sliding door systems

Enigma NFR Shadow gap frame kit

Enigma Kit contents 5

www.selo-uk.com

Frame fixings Frame trims and sliding gear

S03 strike

(Single door x1, Double door n/a)

2

Strike jamb seals 5

S02 leading edge profile

(Single door x2, Double door x4)

S01 head profile

(Single door x1, Double door x2)

3

Sliding gear set 6

1

S04 Shadow gap cover trim

(Single door x5, Double door x6)

4Type-9 50mm gold screws

Type-8 42mm self drilling

drywall screws

4

3Type-7 35mm self drilling drywall

screws

2

30mm Panel pins 5

Type-5 25mm self drilling screws1

www.selo-uk.com Enigma Pocket sliding door systems

Enigma Kit contents

Pocket door kit

Door guide pin and channel8 Brush strip 9Remote stop7

7

Intermediate jambs4

Base channel1

Intermediate jamb insert5

Head channel2

Sliding track6

Leading edge jamb3

Kit fixings

Type-4 30mm screw Type-5 25mm self drilling screw

Type-2 40mm screwType-1 19mm pan head

self drilling screw

1

4 5

2

Type-3 50mm screw 3

Please note

All fixings will come pre-packaged to

suit your specific project requirements.

A) Kit installationBefore installation please ensure you have carried out the recommendations in the ‘Wall Construction Preparation’ booklet.

Check opening

Cut the head channel to suit the structural

opening width.

Prepare head channel and top track

1

2

Enigma Channel and track installation

Cut the sliding top track to the

structural opening width - less 80mm.

Mark 75mm from the end of the head channel.

Mark up

Top track preparation

4

3

Line the end of the top track with the mark

and pilot drill the holes through the head

channel.

Important

Ensure the groove in the center of the track and the head

channel line up as shown.

Pilot hole the head channel5

9

It is very important to ensure that the

opening is square and level and the opening

dimensions are correct.

Important

If you are using a touch latch then you need to add 25mm

extra to the rear of the structural opening.

If you are using an Enigma self closing device then you

need to add 35mm onto the structural opening width.

Enigma Channel and track installation

Slide the remote stop into the groove so the

holes line up, enabling you to install the track.

Important

If you are using the soft close mechanism then you need

to insert the cassette with rollers and stop into the track

now before the track is installed.

Insert the remote stop into the top track6

Put the head channel in place and fix using

Type-2 screws.

Line the top track up with the pilot drilled

holes and fix using Type-3 screws.

Fit the head channel and top track

If installing a double door divide the structural

opening width dimension in two and cut

two head channels to this length. Mark

30mm from the end of both head channels,

line up the end of the sliding track and

pilot drill through the fixing holes. Butt the

head channel together in the center of the

structural opening and fix into place. Line the

sliding tracks up and fix into place also.

Fitting double doors?

7

7a

Cut and fit the base channel8

Cut the leading edge and intermediate jambs

to the correct height so it slides into the head

and base channel.

Cut pocket sides to length9

Cut the intermediate timber insert 100mm

shorter than the aluminium jamb and slide

the insert into the intermediate jamb so it sits

50mm from each end.

Important

When using door leafs wider than 950mm the kit will be

supplied with extra intermediate jambs to be fitted equally

space within the pocket width.

Cut and fit intermediate timber insert10

11

Cut the base channel to the door leaf

width - 20mm.

Butt the base channel against the rear stud

and fix into place using Type-2 screws.

Important

If using an Enigma self closer then the sole plate length

is door leaf width +50mm.

If using an Enigma touch latch then the sole plate

length is door leaf width +40mm.

Enigma Channel and track installation

Fit pocket sides and fix the jamb11

The wall can now be plaster-boarded. Use

Type-5 self drilling screws when fixing the

plasterboard to the profile.

Important

If you are using the self closing mechanism then fit

plasterbaord to one side of the wall only until the door

and self closer is fitted and working correctly.

Fit the plasterboard13

Using x2 Type-4 screws fix the floor pin into place

in the end notch.

Fit door guide pin12

B) Door leaf installationWith the FD30 concealed system the door leaf needs to be hung before the frame is fitted.

Fit the head brackets 150mm from edge of

the door leaf to center of the bracket. Use the

screws provided.

Important

If you are using the simultaneous opening mechanism

then it needs to be installed now.

If using a simultaneous opening the door leaf height

needs to be reduced by an extra 5mm.

If you are using a self-closing mechanism then fit

plasterboard to one side of the wall only until the self-

closer is fitted and working correctly.

Fit head brackets1

13

Tap the black nylon door guide channel into

the groove in the bottom of the door.

Fit the guide channel2

Slide the intermediate jamb into the head and

base channel so it sits centrally in the pocket and

fix into place with Type-1 self drilling screws. Slide

the leading edge jamb into place at the bottom with

notched end at the top, the flange sits hard against

the end of the base channel. Plumb the jamb and fix

into place using the Type-1 screws.

Important

If you’re using the self closing mechanism then this must be

installed with the door before you plasterbaord one side of the wall.

Enigma Door leaf installation

Hang the rear door bracket onto the trolley bolt.

Hang the door4

4.1 4.2

4.1 The bracket fits onto the bolt as shown

4.2 Feed the rest of the door at leasthalfway into the pocket and hang the front bracket onto the trolley bolt

Adjust the remote stop so it holds the door

flush with the pocket end and fix into place

with the self drilling screw provided.

Fix remote stop into place5

Slide the white nylon door stop into the track

and fix into place by tightening the grub screw.

Important

This needs to be adjusted to ensure it stops and holds

the door in the correct place.

Fit the front the door stop6

Fit the track end block into place using the

screw provided.

Fit track end block7

15

Insert trolley’s into track and adjust the bolts

so it sits 20-25mm beneath the track.

Assemble gear3

Enigma Frame installation

C) Frame installationNow the door leaf is hung you are ready to install the concealed frame.

Cut the brush strip to length and fit to the leading

edge aluminium profile.

Important

If you are using the simultaneous opening mechanism then it

needs to be installed before you fit the frame.

Position it in the center of the strike stud and fix

into place using Type-9 screws.

Fit brush strip Cut ‘S03’ to opening height

Cut S02 to the height of the opening and

fix into the aluminium profile flange using

Type-5 screws.

Cut S01 to the distance between the 2 timber

side jambs. Slot into place in the head.

Install ‘S02’ Install ‘S01’

1 3

2 4

17

Enigma Frame installation 19

Clad the pocket with a second layer of

plasterboard over the timber frame. Using

Type-7 screws.

The second layer of plasterboard needs to stop

short of the timber frame edge by 40mm. This

allows for the shadow gap and trims.

Cut the aluminium trim to length mitring it at the

corners. Fix into place using Type-8 screws.

2nd layer of plasterboard

2nd layer of plasterboard Fit the plasterboard shadow trim

5

6 8

Cut the timber shadow gap trim to height

and width. It will need to be mitred at 45

degrees in the corners.

Fix the trim into place using pins.

Fit the S04 shadow gap trim7

You have now completed installation of your Enigma Pocket sliding door system.

Congratulations!

Enigma Frame installation

Enigma Pocket sliding door systems

Now the wall can be plastered or tape and jointed

up to the plasterboard shadow gap trim.

Once the plaster/jointing compound has dried the

walls and trims can be decorated.

The strike jamb seals are push fitted to the

grooves in S03.

Plaster/tape joint and paint

Fit strike jamb seals

9

10

Enigma Contact

© 2015 by Selo. All rights reserved.

No part of this publication may be reproduced in any material form (including photocopying or storing it in any medium by electronic means and whether or not transiently, or incidentally to some other use of this publication) without the written permission of the copyright owner. Application for the copyright owner’s permission to reproduce any part of this publication should be addressed to Selo.

Where colour and finish samples are shown within this document limitations in the reprographics process mean absolute colour accuracy cannot be guaranteed. Where colour matching is critical, a sample of the material can be provided on request.

Selo reserves the right to alter specification and designs without prior notice.www.selo-uk.com

Visit our new website, loaded with the content and features you want to see.

www.selo-uk.com

Find out moreFor help and advice with your installation contact our experienced team.

tel 0845 054 6327 / email sales@selo-uk.com

Selo House 11-14 Houghton Regis Trading Centre Cemetery Road Bedfordshire LU5 5QH

tel 0845 054 6327 email sales@selo-uk.comwww.selo-uk.com

For help and advice with any Selo product, call the support team on:

0845 054 6327