Final Power point EGR 110
-
Upload
muntabir-choudhury -
Category
Documents
-
view
222 -
download
0
Transcript of Final Power point EGR 110
![Page 1: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/1.jpg)
RC Vehicle Kyle Coats, Tasin Choudhury, Zach Dennin, Daniel
EstevesEGR110- Introduction to Engineering II
![Page 2: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/2.jpg)
We were tasked with designing and fabricating a battery powered car, which must be able to travel 100 meters in the least amount of time as possible. In addition to that the car must be able to carry a load of one kilogram and have at least one 3D printed part.
![Page 3: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/3.jpg)
Name Job title ResponsibilitiesZach Dennin CAD Design Assuring the Quality of 3D
Tasin Choudhury Designer Headed design selection
Kyle Coats Communications Managing team communication and keeping the team on track
Daniel Esteves Fabrication Responsible for assuring the fabrication part & pricing
![Page 4: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/4.jpg)
![Page 5: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/5.jpg)
Requirements Specification
Cost Less than $100Distance Must be able to travel 100mSpeed Travel as quickly as possibleLoad Must be able to carry up to 1kgBuild Time Must be fabricated by April 21st3D print One component must be 3D printedResources Must be purchased through RC Planet,
B&G HW, HostettersCircuitry Create a circuit involving a switch and
resistor suitable for running the carts
![Page 6: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/6.jpg)
Pugh Table
![Page 7: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/7.jpg)
Chosen Design Idea
![Page 8: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/8.jpg)
Traxxaas Anaconda
Integy 1/10
Pro-line 1/16
Size Datum = -Tread = =Cost + -+ 1 0- 0 2Total 1 -2
![Page 9: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/9.jpg)
Fabrication
• Different 3D part than originally planned
• Replaced body with plywood
• Used crimped connection for circuit
• Included 5ohm resistor and switch
![Page 10: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/10.jpg)
Obstacles
• Cracking of resistor• Motor too high off axle• Gears became worn• Axle shifted and wouldn’t sit correctly
![Page 11: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/11.jpg)
Description Total Cost
Motor $ 13.99
Wheels $ 27.98
Heli-max Pinion $ 0.89
Slotted Flats $ 7.99
Threaded Rod $ 1.29
Spur Gear $ 2.79
Pinion Gear $ 2.39
Resistor $ 6.68
3D Part $ 24.07
Plywood $ 1.00
Switch $ 0.69
Shop Supplies $ 5.00
Clamp $ 5.00
$ 99.76
![Page 12: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/12.jpg)
![Page 13: Final Power point EGR 110](https://reader036.fdocuments.in/reader036/viewer/2022062412/587ea6401a28ab2a4a8b6beb/html5/thumbnails/13.jpg)
Final Product