PH-1.18

PROJECT INFORMATION APPROVAL STAMPProject: q Approved

Address: q Approved as noted

Contractor: q Not approved

Engineer: Remarks:

Submittal Date:

Notes 1:

Notes 2:

WALL BRACKETS

Fig. 551 (Formerly Afcon Fig. 551) Revolver Bracket

Size Range: 3⁄8" rodMaterial: Carbon SteelFinish: Pre-Galvanized per ASTM A653Service: Wall Bracket mounts on the side of wood, steel, and concrete walls and beams to support up to 4" NPS horizontal piping.Approvals: cULus Listed (UL 203)Patents: No. 6,568,642Installation:

• Mount on the side of wood, steel, or concrete walls and beams using the fasteners listed in NFPA 13 and the mounting fastener table listed below.

• Fully thread the rod through the threaded mounting hole.Features:

• Universal fastener array optimizes the fastener size and placement for various structure types and pipe sizes.

• Threaded mounting hole features a lead-in radius for easier installation.• No backing nuts are required on the rod.• Center mounting hole accepts 3⁄8" and 1⁄2" fasteners

Ordering: Specify figure number and description.

FIG. 551: DIMENSIONS (IN) • WEIGHT (LBS)

Rod Size A B C D E øH1 øH2 Approx.

Weight/1003⁄8 2 11⁄4 13⁄8 3⁄4 11⁄4 1⁄4 1⁄2 12

A

B

D

øH2

øH1(6 Places)

C

E

PH-1.18

WALL BRACKETS

Fig. 551 (Formerly Afcon Fig. 551) Revolver Bracket (cont.)

cULus LISTED MOUNTING FASTENERS FOR STEEL PIPE

Structure Fastener QTY Pipe Size Fastener Position Structure Fastener QTY Pipe

Size Fastener Position

Wood1⁄4 x 11⁄2" Lag Screw

#14 x 11⁄2" TEK Screw1 ≤ 2 " or

Steel(18ga Min)

#14 x 1" TEK Screw 3 ≤ 4" or

Wood1⁄4 x 11⁄2" Lag Screw

#14 x 11⁄2" TEK Screw2 ≤ 4" or

Steel(20ga Min)

#14 x 1" TEK Screw 1 ≤ 2 "

Wood #16 x 2" Drive Screw 2 ≤ 2 " orSteel

(20ga Min)#14 x 1" TEK Screw 2 ≤ 3" or

Wood #16 x 2" Drive Screw 3 ≤ 4" orSteel

(20ga Min)#14 x 1" TEK Screw 3 ≤ 4" or

Wood1 3⁄8 x 21⁄2" Lag Screw 1 ≤ 2 "Steel

(22ga Min)#14 x 1" TEK Screw 3 ≤ 2½" or

Wood11⁄2 x 3" Lag Screw 1 ≤ 4"

Steel(18ga Min)

#10 x 1" TEK Screw 1 ≤ 2½" or

Steel (14ga Min)

#14 x 1" TEK Screw 1 ≤ 3" orSteel

(18ga Min)#10 x 1" TEK Screw 2 ≤ 3 " or

Steel (14ga Min)

#14 x 1" TEK Screw 2 ≤ 4" orSteel

(18ga Min)#10 x 1" TEK Screw 3 ≤ 4" or

Steel (16ga Min)

#14 x 1" TEK Screw 1 ≤ 2½" orSteel

(20ga Min)#10 x 1" TEK Screw 2 ≤ 3 " or

Steel (16ga Min)

#14 x 1" TEK Screw 2 ≤ 4" orSteel

(20ga Min)#10 x 1" TEK Screw 4 ≤ 4"

Steel (18ga Min)

#14 x 1" TEK Screw 1 ≤ 2½" orSteel

(22ga Min)#10 x 1" TEK Screw 3 ≤ 3 " or

Steel (18ga Min)

#14 x 1" TEK Screw 2 ≤ 3" or

Note 1: Per NFPA 13-2016 Table 9.1.5.3.1 and NFPA 13-2013 Table 9.1.5.3.1 Note 2: Sheet Metal Screws are acceptable alternatives for TEK Screws