Ficci Report 2011
Transcript of Ficci Report 2011
-
8/6/2019 Ficci Report 2011
1/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
FICCI QUARTERLY SURVEY
ON
INDIAN MANUFACTURING SECTOR
March 2011
Federation of Indian Chambers of Commerce & Industry
-
8/6/2019 Ficci Report 2011
2/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
TABLE OF CONTENTS
Page No.
Introduction 1
Textiles 5
Capital Goods 6
Machine Tools 7
Cement 8
Consumer Durables 9
Forging 10
Metals 11
Chemicals 12
Auto
Tyre 15
Leather 16
Paper 17
Miscellaneous Industry 18
-
8/6/2019 Ficci Report 2011
3/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
1 | P a g e
Introduction
FICCI has conducted its Quarterly Manufacturing Survey for the quarter January-March 2011
(Q-4). The survey has tried to gauge the expectations of manufacturers for Q-4 from major
sectors like textiles, capital goods, metals, chemicals, machine tools, tyres, cement, consumer
electronics, automotive, leather & footwear, paper, forging etc. Responses have been drawn
from over 400 manufacturing units belonging to both large and SME segment.
Growth Scenario
Overall the sentiments and expectations of manufacturing sector for Q-4 have seen a dip vis--
vis last quarters. In the survey, 60% respondents reported that they expect higher growth in
their sector for Q-4 vis--vis Q-4 2009-10. This is a significant fall with regard to previous two
quarters in which around 68% (Q-3) and 71% (Q-2) respondents felt that they were expecting
higher growth in their sectors.
Around 77% respondents feel that the growth in the manufacturing sector is going to moderate
for Q-4. While a number of factors are constraining the growth of manufacturing sector, but
most important being the rise in the cost of capital due to monetary tightening measures of
RBI. Below, we have given the response on RBIs monetary tightening measures.
Cost of Finance
Hike in the policy rates of RBI in the last few months has significantly affected the cost of
borrowing for manufacturers. In Q-4, over 34% respondents reported that their cost of
borrowing has increased significantly in last two to three months. Around 43% respondents felt
that the hike in policy rates had a moderate impact on their cost of borrowing. But compared to
previous Quarter (Q-3) the situation has worsened. In Q-3, as per FICCI Survey, only 13%respondents felt that their cost of borrowing had increased significantly, whereas in Q-4 34%
respondents are feeling the heat of rising interest rates. Sectors where the impact is seen the
most are Automotive, Cement and Tyres.
-
8/6/2019 Ficci Report 2011
4/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
2 | P a g e
Impact of Hike in RBI Policy Rates on Cost of Financing
Quarter-3 2010-11
Quarter-4 2010-11
Source: FICCI Survey
Economic environment
-
8/6/2019 Ficci Report 2011
5/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
3 | P a g e
Quite a few respondents in the survey have reported that uncertainty in economic environment
has increased further. Over 40% respondents of the survey reported that economic uncertainty
is acting as a significant constraint for the growth of the sector. Another 28% respondents saw
economic uncertainty as a moderate constraint for the growth of the sector.
Capacity Utilization
In terms of capacity utilization there is not much difference or variation between Q-4 and Q-3.
In Q-4, around 53% respondents reported that they were operating at higher capacities vis--vis
last year, as compared to 52% in Q-3. Similarly, around 32% respondents reported that they
were operating at same level of capacity utilization as last year in Q-4- same percentage as in Q-
3.
Capacity Addition
In terms of capacity addition, around 52% respondents plan to have capacity additions in next 6
months. However, a significant proportion i.e. 48% still feels that there are number of
constraints to capacity additions. Sectors where majority of the respondents reported that their
capacity additions are not coming through significantly are textiles and steel. In other sectors
like Automotive, Capital Goods, Machine Tools, Leather, Chemicals, Cement, Paper and Forgingthere is going to be moderate increase in capacities.
Order Books
The demand conditions for manufacturing sector in Q-4 is similar to that in Q-3. In both the
quarters around 54-55% respondents have higher order books for the quarter compared to
previous quarter.
Employment
Around 44% respondents reported that they intend to increase their workforce in next 3
months. Sectors where majority of the respondents intend to hire new workforce are
Automotive, Tyre, Leather, Capital Goods, Electronic Goods and Forging.
-
8/6/2019 Ficci Report 2011
6/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
4 | P a g e
Sectoral Growth
Looking at growth expectation in different sectors, five out of fourteen sectors in the survey arelikely to witness strong growth of over 10% in Q-4. These sectors are Capital Goods,
Automotive, Machine Tools and Consumer Durables. For three sectors namely Chemicals,
Forging and Tyre growth is likely to be moderate (between 5 to 10%) in Q-4 as compared to last
year. Sectors like Cement, Paper, Steel, Metals, Textiles and Miscellaneous are likely to witness
low growth of less than 5% in Q-4.
Sector Growth
Cement Low
Paper Low
Steel & Metals Low
Textiles Low
Miscellaneous Low
Chemicals Moderate
Forging Moderate
Tyre ModerateMachine Tools Strong
Automotive Strong
Electronics & Consumer Durables Strong
Leather & footwear Strong
Capital Goods StrongNote : Strong > 10%; 5% < Moderate < 10%; Low < 5%
Source: FICCI Survey
Exports
Exports seem to be picking-up for the manufacturing sector in Q-4. Over 54% respondents
reported that they are expecting higher exports in Q-4 vis--vis last year. Almost, all the sectors
are expecting growth in their exports for Q-4 vis-a-vis last year.
-
8/6/2019 Ficci Report 2011
7/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
5 | P a g e
TEXTILES
In the current quarter i.e. January- March 2011, 87% respondents are expectingincreased or same production levels. However, average production growth is expected
to be around 4% during January- March 2011 implying that the sector may witness a
marginal slowdown vis--vis last quarter.
In January- March 2011, 73% of textiles firms are expecting to have either same orhigher number of orders as in October- December 2010.
Average capacity utilization is hovering around 84% in the textiles sector with almosthalf of the respondents operating at a capacity utilization more than that of last year.However, majority of respondents (60%) are not planning to increase their capacity in
next 6 months but those who are planning to increase their capacity are planning to
increase it in the range of 5-50%. Firms in textiles sector are facing the following
problems in adding capacity:
High real estate costs making business unavailable TUF scheme has been put on hold by Ministry of Textiles, it is a great cause of
concern for the sector Labor Issues Shortage in power Raw material prices of cotton Rising cost of capital
Around 60% respondents have reported that their exports in October- December 2010were higher than the same quarter last year. But textile exports may see a downturn in
the current quarter since only 33% respondents are expecting higher exports vis--vis
the year ago quarter. More so because of the existing restrictions on yarn exports.
Two third of the respondents in the textiles sector are not planning to hire new workersin the next three months and one third of the respondents in the textiles sector who are
planning to hire new workforce are thinking of increasing their manpower by 4-25%.
-
8/6/2019 Ficci Report 2011
8/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
6 | P a g e
73% respondents are expecting the manufacturing growth rate to be moderate but theyfeel the following incentives need to be provided by the Government to enhance
growth:
Restore the suspended TUFs Scheme for textile industry. Remove quantitative ceiling on cotton yarn exports Check on Cotton Prices Finance availability needs to be smooth and interest rates need to be lowered Amend labour laws to make them industry friendly Need to have a strong focus on improving infrastructure & utilities
87% respondents in the sector reported that policy rates hike by Government hasimpacted their costs of borrowing. For some respondents the impact was significant
while for others the impact on cost of borrowing was moderate.
Units in the textiles sector are significantly affected by high prices of rawmaterials/intermediates, deficiency of raw materials, deficiency of power, labour
related issues and availability of skilled manpower. Other issues faced by textile sector
are shortage of finance, lack of domestic and export demand, competition from imports
and uncertainty of economic environment.
Restriction on cotton yarn exports will have serious implications on expansion plans ofspinning industry and delay in release of incentives like TUFS, power subsidy, sales tax
reimbursement are also hurting the textile producers.
Capital Goods sector
In the current quarter, almost all the respondents expect either an increase in productionvis--vis January-March 2010. The average increase is expected to be around 23%. Almost
all the respondents have reported that their order books are likely to experience an
increase in January-March 2011 compared to October-December 2010 Quarter.
Currently, the capacity utilization in this sector is hovering around 80-85% and for 88%respondents the capacity utilization is higher as compared to previous year. Most of the
-
8/6/2019 Ficci Report 2011
9/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
7 | P a g e
respondents have plans to add capacity in next 6 months. On an average, the capacity
addition is expected to be around 10-20%.
The scenario is not that encouraging in export for this sector. Most of the respondentsreported either same or lower level of exports in October-December 2010 quarter as
compared to October-December 2009. The situation is likely to improve in the current
quarter as around 60% respondents expect their exports to increase in the current quarter
vis--vis last year and merely 15% expect them to fall as compared to January-March 2010.
75% of the respondents in this sector indicated that they are planning to hire newworkforce in the range of 3-20% in the near future.
Almost all the respondents in the sector expect the growth rate of manufacturing sector tomoderate in the coming months.
Almost all the respondents reported that RBIs monetary policy tightening has moderatelyimpacted their cost of borrowing.
High price of raw material and lack of skilled manpower are two most significant constraintsfor the sector which can affect growth of the sector. Apart from this, the sector has also
urged the Government to provide level playing field vis--vis imports.
Machine Tool Industry
Most of the respondents are expecting higher levels of production in January-March 2011quarter as compared to same quarter of previous year. The increase is reported to be as
high as 50% as compared to January-March 2010 but some of them have specified the
reason for this increase to be lower production levels in January March 2010.
Respondents are also expecting almost same level of orders in January - March 2011
compared to October-December 2010.
At present, the machine tools industry is operating at a capacity of 90% and above. Majorityof the respondents reported an increase in capacity utilization as compared to last year and
they have plans to add further capacity in next six months by around 50%. As per the
-
8/6/2019 Ficci Report 2011
10/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
8 | P a g e
respondents, one of the main hindrances in their expansion plans is bottlenecks in the
supply chain.
Majority of the respondents reported an increase in their exports in October-December2010 as compared to October-December 2009. The similar situation is expected to prevail in
the current quarter i.e. January-March 2011 also as most of the respondents expect an
increase in exports as compared to last year.
Most of the respondents do not have plans to hire new workforce. Majority of the respondents believe that the growth rate of manufacturing sector is going to
moderate in the coming months. Machine Tool industry has also suggested that
Government needs to control inflation, reduce rate of interest for manufacturing sector to
revive growth in manufacturing sector.
The sector also reported a moderate increase in the cost of borrowing due to increasedpolicy rates by RBI.
Some of the significant constraints for this sector are shortage of working capital finance,competition faced from imports and lack of skilled manpower. Apart from this, prices of raw
material, deficiency of power and labour related issues are other important constraints
cited by the industry.
CEMENT
Growth is likely to continue in Cement Sector in the next quarter with productionexpected to grow by 5% in January- March 2011 compared to 2010.
Around 90% respondents have reported that their order books are likely to see adownturn in January- March 2011 compared to the previous quarter.
Capacity utilization is in the range of 70 to 90% in the cement sector, which is less thanthat of last year for 95% respondents. Majority of the firms are planning to add capacity
in next six months. On an average, capacity addition is likely to be 10%. Cement
producers are hampered by high coal costs and environment clearances while adding
capacity.
-
8/6/2019 Ficci Report 2011
11/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
9 | P a g e
Exports of Cement have declined in October- December 2010 compared to last year.Exports are not likely to see a revival in the next quarter also and are likely to be 20%
less than January- March 2010 quarter.
Most of the firms in the cement sector are planning to hire new work force in next threemonths but only moderately.
Most of the respondents in the cement sector believe that the growth rate ofmanufacturing is likely to be moderate in 2010-11. Respondents feel that following
steps need to be taken by the Government to enhance growth of the sector:
Investment in the infrastructure sector is required to boost the demand for cementproducts and speed up the planned projects
Interest rates need to be reduced. Excise duty and VAT need to be reduced Inflation needs to be tackled on an urgent basis GST needs to be implemented soon
50% respondents in the Cement sector reported that monetary tightening by theReserve Bank of India has significantly impacted their costs of borrowing. However, the
remaining respondents are moderately affected by Monetary tightening.
High prices of raw materials is acting as a significant constraint for the sector. Otherissues which are significantly affecting growth of cement sector are deficiency of raw
materials, uncertainty of economic environment and lack of domestic demand. Some of
the respondents reported deficiency of power, shortage of working capital finance, lack
of export demand, competition faced from imports and inadequate availability of skilled
labor as factors moderately affecting their growth.
Consumer Electronics
In the current quarter, i.e. January-March 2011 also majority of respondents expectincreased level of production. Most respondents have reported that their orders are
expected to increase in January-March 2011 as compared to October-December 2010.
-
8/6/2019 Ficci Report 2011
12/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
10 | P a g e
On an average the capacity utilization in this sector stands at around 90% and above. Mostof the firms have reported that their capacity utilization is higher as compared to last years
capacity utilization. But most of the firms are not planning any further increase in capacity
in next 6 months.
Most of the electronics producers reported an increase in exports during October-December 2010 compared to same quarter last year and the trend is likely to continue in
the next quarter also.
Most of the respondents reported that they are planning to hire new workforce in next 3months.
Most of the respondents believe that the manufacturing sector will continue to experiencehigh growth rate in the coming months.
Around 60% respondents reported that tightening of monetary policy by RBI hasmoderately impacted their cost of borrowing.
For electronic industry prices of raw material has been identified as the most significantfactor affecting their progress. Other important constraints to the industry are deficiency of
power and competition faced from imports.
Forging Industry
Most of the respondents expect an increase in the production levels in January-March 2011quarter vis--vis last year. The average increase is reported to be around 10%. Almost all the
respondents expect an increase in orders in January-March 2011 quarter as compared to
October-December 2010 quarter indicating better demand conditions.
Currently, forging industry is operating at an average capacity utilization of 50%-70%. Mostof the respondents have reported an increase in their capacity utilization as compared to
last year. Some of them also reported that they have plans to increase their capacity further
in the next 6 months.
Exports for most of the respondents increased in October- December 2010 via-a-vis thesame quarter last year and are likely to grow in the next quarter as well.
-
8/6/2019 Ficci Report 2011
13/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
11 | P a g e
Most respondents are planning to hire workforce in next 3 months. The forging industry is very confident of growth of Indian manufacturing sector in coming
months.
The sector also reported a moderate increase in the cost of borrowing due to increasedpolicy rates by RBI.
Most of the respondents in this sector reported high prices of raw materials, deficiency ofpower and labour related issues to be the most significant constraints to their growth.
Metal and Metal Products
In the quarter January-March 2011, around 88% respondents expect either higher or sameproduction levels as compared to January-March 2010. The average increase in the
production level is expected to be around 5%. 75% of the respondents expect same number
of orders in the quarter January-March 2011 as compared to October-December 2010. The
rest of respondents expect an increase in number of orders.
Currently, the industry is operating at an average capacity utilization of 85% and for 40%respondents it is higher than that of last year. For the rest of them the capacity utilization is
the same as compared to the last year. Around 88% respondents reported that they are not
planning to increase their capacity in next 6 months. Some of the problem areas mentioned
by the industry are as follows:
o Volatility in raw material prices like, scrap, DRI, Fuelo Power shortage
Almost 75% respondents reported higher level of exports for October-December 2010 via-a-vis October-December 2009. In the current quarter also, almost 50% respondents expect
higher level of exports as compared to January-March 2010 and 25% respondents expect
same level of exports as last year.
Around 88% respondents reported that they do not have any plans to hire new workforce innext 3 months.
-
8/6/2019 Ficci Report 2011
14/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
12 | P a g e
Almost all the respondents expect the manufacturing growth to moderate in the comingmonths. The following points have been suggested by the industry to revive the growth rate
of the sector:
o More emphasis on infrastructure development and creating more demand by way ofspending on new infrastructure.
o Lower interest rate for working capital & long term.o Power and fuel cost regulation should not change frequently, that too post
consumption.
Over 50% respondents feel that tightening of monetary policy by RBI has significantlyimpact the cost of borrowing of the industry.
Higher price of raw material has been reported as the most significant constraint formanufacturers in this industry. Around 65% respondents reported it to be the most
significant constraint. Other major problems faced by this industry have been identified as
shortage of power and raw material, competition faced from imports and lack of availability
of skilled labour.
CHEMICALS, FERTILIZERS AND PHARMACEUTICALS SECTOR
90% respondents are expecting either same or increased production in the currentquarter vis--vis the same quarter last year but growth is likely to slow down in the
current quarter and the average growth is likely to be 8%.
89% respondents are expecting either same or higher number of orders in January-March 2011 compared to what prevailing in October- December quarter. Only 11%
respondents are expecting a fall in the number of orders.
Capacity utilization stands at around 80% in chemical, fertilizers and pharmaceuticalssector. Current capacity utilization is higher than last year for two third of the
respondents. Also, 67% manufacturers are planning to add capacity in next six months in
the range of 10 50%. Firms in this sector are constrained by inadequate supply of
-
8/6/2019 Ficci Report 2011
15/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
13 | P a g e
inputs like natural gas. Also, Government policies related to environment need to be
more investor friendly.
In October- December 2010, 56% respondents reported an increase in exports vis--vislast year. Exports scenario is likely to remain same in the current quarter also i.e January
- March 2011.
Around 67% respondents are not planning to hire any new workforce in next 3 monthsand those who are planning to hire are planning to do so at a marginal rate only (5%).
67% respondents are hopeful that the manufacturing sector will grow in 2010-11 thoughat a moderate rate, following actions need to be taken by the Government:
Need clarity and transparency in Government regulations on licensing andsetting up of new facilities.
Interest rates need to be lowered and liquidity needs to be improved. Petroleum prices need to be stabilized Government should encourage manufacturing Inflation control and fiscal management Need to have a favorable policy for investment in fertilizer sector
For one third of respondents, hike in policy rates by RBI has lead to a significant rise incost of borrowing and for another 44% respondents RBI rate hike has increased the cost
of borrowing but by a moderate magnitude.
High prices of raw materials, uncertainty of economic environment, shortage of skilledlabour and competition faced from imports are significantly impacting the growth of
chemical sector. Deficiency of Power, labour issues, shortage of working capital finance,
deficiency of raw materials, lack of domestic and export demand are other constraints
faced by chemical and fertilizer firms.
Automotive
In the current quarter, almost 70% respondents expect an increase in their production ascompared to last years quarter. The increase is expected to be around 30%. 90% of the
-
8/6/2019 Ficci Report 2011
16/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
14 | P a g e
respondents are expecting an increase in number of orders in January-March 2011
compared to October-December 2010 quarter.
More than 60% respondents have reported an increase in capacity utilization in October-December 2010 quarter vis--vis last year. The average capacity utilization in the industry
stands at around 80%. 60% of the respondents in the automotive sector are planning to
expand their capacity further by an average of 25-30%. Some of the respondents have
mentioned lack of skilled manpower, land acquisition etc as some of the problems faced by
industry in planning their capacity expansion.
60% respondents in automotive sector have reported an increase in exports in October-December 2010 quarter. Similar situation is likely to prevail in the current quarter also with
60% respondents expecting their exports to increase as compared to last year.
90% respondents are planning to hire new workforce in coming 3 months by an average ofaround 40%.
90% respondents expect the growth rate of manufacturing to moderate in the comingmonths and following are some of the suggestions given by the industry to revive the
growth in the sector:
o Easier land acquisition normso Lower interest rates, lower inflation, man power availability.o Proper power at reasonable rate. Good infrastructure.o Training institutes to develop skilled labour.o Control over prices of crude oil and other important raw materials.o Constant check of industrial inflationo Boost to JNNURM (Jawaharlal Nehru National Urban Renewal Mission) projectso Reduction in PLR for term and short termso Single window facilities declared by Government should be made available to the
industry.
o Control inflation & increase demand stimulus measures. Investment in newinfrastructure projects is required.
o Manage political instability.
-
8/6/2019 Ficci Report 2011
17/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
15 | P a g e
Almost all the firms in this sector have felt that hike in policy rates by RBI has resulted inincreased cost of borrowing for them and 67% of them have indicated that the impact has
been significant.
Prices of raw material, archaic labour laws and inadequate availability of skilled labour havebeen identified as some of the most important constraints for automotive industry. Some of
the manufacturers have also reported uncertainty of economic environment as a constraint
to their growth.
Tyre Industry
For January-March 2011 quarter, most of the respondents expect higher production levels.The production is expected to increase by 8-10%. Almost all the respondents expect either
higher or same number of orders in Q-4, indicating robust demand.
On an average, the capacity utilization in the tyre industry is in the range of 70-90%. It ishigher than October-December 2009 quarter for most of the respondents. Also, majority of
respondents are planning to add capacity in next 6 months.
On exports front, majority of the respondents have experienced an increase for October-December 2010 quarter as compared to same quarter in 2009. In January-March 2011
quarter also, tyre manufacturers expect higher level of exports as compared to same
quarter of 2010.
The tyre industry is planning to hire workforce in next 3 months. Almost all the respondents in the sector believe that the manufacturing growth rate is
expected to moderate in the coming months and to revive the growth, the industry has
suggested the government to lower tariff rates on raw materials which are not available
domestically, facilitate FDI and reduce interest rate and thereby improve access to credit.
One of the major & significant constraints for this sector is hardening of raw material priceand deficiency of raw material, particularly of natural rubber. Shortage of working capital
finance, uncertainty in economic environment and competition faced from imports are
some of the other important challenges for the sector.
-
8/6/2019 Ficci Report 2011
18/21
-
8/6/2019 Ficci Report 2011
19/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
17 | P a g e
Training to unskilled labor More incentives like drawback benefits need to be provided
Monetary tightening by RBI has impacted the cost of borrowing of 86% leather &footwear firms. Impact was significant for half of the borrowers but for the other half
impact was moderate.
Firms in leather and footwear sector are significantly constrained by high prices of rawmaterials, deficiency of raw materials, lack of export demand, uncertainty of economic
environment and availability of skilled manpower for their operations. Other factors
acting as impediments for leather sector are deficiency of power and labour issues.
PAPER
Production is likely to slowdown in January- March compared to the last quarter asaverage growth is reported at 5%.
Order books of paper manufacturers are likely to show the same trend in January-March as October- December quarter.
Capacity utilization stands at 90% in paper sector which is more than last year formajority of producers. Also, most of the producers are planning to expand their
capacity, on an average by 5%.
Exports of paper manufacturers have witnessed growth in October- December 2010compared to the same quarter last year. In January- March also respondents in this
sector are expecting higher exports than last year.
Most respondents in the paper industry are not planning to hire workforce in nearfuture.
Paper manufacturers believe that manufacturing growth rate will be moderate in 2010-11 and government needs to carry on with stimulus measures.
Also, hike in policy rates by RBI has moderately impacted the cost of borrowing of paperproducers.
-
8/6/2019 Ficci Report 2011
20/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
18 | P a g e
High prices of raw material and deficiency of raw material are acting as significantconstraint for the paper manufacturers. Labor related issues, competition faced from
imports and availability of skilled labor are other issues faced by the paper industry.
MISCELLANEOUS INDUSTRY
Production is likely to grow further in January- March since 80% of the respondents areexpecting an increase in production. Average rise in production is expected to be around
3%.
80% respondents are expecting higher orders in January- March 2011 compared toOctober- December quarter.
Units under the miscellaneous category are reportedly running at around 64% of theircapacity. For most of the respondents the capacity utilization is same or more than last
year. One fifth of the units are planning to enhance their capacity by around 10-15%.
Firms belonging to Miscellaneous sector are facing following problems while adding
capacity:
Uncertainty in economic condition Uncertainty in future orders Power shortage
Exports of two third of the units in the miscellaneous category were higher than lastyear in October- December 2010 and most of the firms are expecting higher exports in
January- March 2011 also vis--vis the same quarter last year.
Around 80% respondents reported that they are not planning to increase theirworkforce. Rest of the respondents are planning to increase 3-5% of their workforce in
next few months.
50% of the respondents are sanguine about the growth prospects of manufacturing butthey expect the following things needs to be done in order to sustain this growth:
Control over raw material cost & availability Provide training to enhance the skills of labor
-
8/6/2019 Ficci Report 2011
21/21
FICCI QUARTERLY SURVEY ON INDIAN MANUFACTURING SECTOR
19 | P a g e
Continuous power availability Support to manufacturing sector through existing stimulus
For majority of the respondents, hike in policy rates by RBI has resulted in increase intheir borrowing costs.
High prices and deficiency of raw materials, deficiency of power, uncertainty ofeconomic environment and lack of skilled manpower are significantly affecting the
growth rate of this sector. Lack of domestic and export demand, labor issues, shortage
of finance and competition from imports are other hindrances for the miscellaneous
sector.