Fib Erg Last Catalog

CARBON FIBERKEVLAR®

FIBERGLASSEPOXY RESINVINYL ESTER RESINPOLYESTER RESINGEL COATFOAMSANDWICH COREVACUUM BAGGINGWIND ENERGY PRODUCTSMOLD POLISH & RELEASECHROMAVEILTM

FABRIC RACKSSCISSORS & FABRIC AIDSROLLERS & APPLICATORSMEASURINGMIXINGSAFETY & CLEANUPBOOKS & VIDEOS

PG. 1PG. 5PG. 7PG. 12PG. 13PG. 14PG. 15PG. 19PG. 20PG. 21PG. 27PG. 29PG. 31PG. 32PG. 33PG. 35PG. 37PG. 39PG. 41PG. 43

1.800.330.6365WE’RE OPEN

LATER!8:00 am - 8:00 pm ET

MON-FRI

WWW.FIBREGLAST.COM

First Quality Composite MaterialsGUARANTEED


Fibre Glast materials are suitable for the most demanding applications, like aerospace and racing. We only supply First Quality materials and that is one reason why we are The Professionals’ Choice.

EASY TO ORDER!

HOURS OF OPERATION

WWW.FIBREGLAST.COM

1.800.330.6365

8:00 am - 8:00 pm EASTERN TIME, MON - FRI

ORDER BEFORE 2:30 ET FOR SAME DAY SHIPPING!

*OPEN UNTIL 5:00 pm PACIFIC TIME!

FAX: 937.833.6555EMAIL: [email protected]

Browse a huge selection of products. Purchase online through an easy, secure process.

Speak with a knowledgeable sales representative. Place or inquire about an order, obtain a quote, or get technical information about our products.

MERCHANDISE TOTAL SHIPPING CHARGE

Under $100.00 $9.95

$100.01 - $250.00 $19.95

$250.01 - $375.00 $39.95

$375.01 - $500.00 $59.95

$500.01 - $750.00 $69.95

$750.01 - $1,000.00 $119.95

$1,000.01 - $1,500.00 $159.95

$1,500.01 - $3,000.00 $199.95

$3,000.01 - $5,000.00 $249.95

$5,000.01 and Over $399.95

70% of the U.S. population can be reached in 3 days shipping UPS ground from our location.

CENTRAL LOCATION

SHIPPING

HAZARD CHARGESHazard charges are levied by UPS, FedEx, and all transportation companies. Fibre Glast does not profit from these charges. If applicable, hazard charges will be added to your product total before shipping your order. We then remit them directly to the transportation company. We will combine products as the law permits in order to minimize these charges whenever possible.

PAYMENT METHODSVisa, MasterCard, Discover and American Express are the accepted credit cards. Net 30 Terms are available to U.S. corporate clients. Prepayments by check should be made by Certified Bank Check. Orders paid by other types of checks will not be shipped for a minimum of 10 days, upon receipt of check. Wire transfers may be required for international shipments. Wire transfers incur a $50 Bank Handling Fee in addition to any charges assessed by your bank. Purchase orders specifying other terms must be approved in writing by an officer at Fibre Glast Developments Corporation.

PRODUCT GUARANTEESAll products except Vinyl Ester Resin are guaranteed to have a six-month shelf life from date of purchase when stored in unopened containers and at ambient temperatures. Vinyl Ester Resin has only a three-month guarantee.

PRODUCT CERTIFICATIONSMaterial Certifications can be issued to our spec under the following two conditions: If requested when ordering, there is a $5.00 charge per certification for all orders under $500.00. There is no charge for orders over $500.00. If requested after the product has shipped, there is a $25.00 charge per certification regardless of the order size. If retroactive certifications are requested more than 3 months after the product has shipped, there will be a $25.00 charge for each additional month.

RETURNSNotifiy customer service for instructions and authorization. Customer is responsible for all outbound shipping charges resulting from items ordered in error. Items can only be returned in unopened containers or packages determined to be in saleable condition at the discretion of Fibre Glast Developments Corporation.

Fibre Glast Developments Corporation385 Carr DriveBrookville, Ohio 45309

DISPUTESAny disputes which result in legal recourse will be resolved in the courts of Montgomery County, Ohio and under the laws of the State of Ohio and the United States of America.International Air and Freight shipments charged carrier rate plus Handling. Hazard Charges added separately at carrier rate. Prices subject to change without notice. Orders shipped best way, FOB Brookville, OH. Not responsible for typographical errors.

HANDLING ONLY CHARGESWe will charge $10.00 handling for any orders shipped on the customer’s freight account.

INTERNATIONAL ORDERSOur standard shipping charges do not apply to international orders. We will quote your shipping charges by email and get your approval before we ship. All of our prices are in U.S. dollars and no other currencies will be accepted.

PATTERNED CARBON FIBER

CARBON FIBER

KEVLAR®

FIBERGLASS

EPOXY RESIN

VINYL ESTER RESIN

POLYESTER RESIN

GEL COAT

DURATEC & RESIN ADDITIVES

FILLERS, PIGMENTS & GLITTERFLAKE

SPRAY GUNS

FOAM

SANDWICH CORE

VACUUM BAGGING MATERIALS

VACUUM INFUSION

VACUUM FITTINGS

PUMPS & TOOLS

WIND ENERGY PRODUCTS

MOLD POLISH & RELEASE

CHROMAVEILTM

FABRIC RACKS & WORKSTATIONS

SCISSORS & FABRIC AIDS

ROLLERS & APPLICATORS

MEASURING & DISPENSING

MIXING SUPPLIES

MIXING SETS & STARTER KITS

SAFETY

CLEANUP

BOOKS & VIDEOS

PAGES 1-2

PAGES 3-4

PAGES 5-6

PAGES 7-11

PAGES 12-13

PAGE 13

PAGE 14

PAGE 15

PAGE 16

PAGE 17

PAGE 18

PAGE 19

PAGE 20

PAGES 21-22

PAGE 23

PAGES 24-25

PAGE 26

PAGES 27-28

PAGES 29-30

PAGE 31

PAGE 32

PAGES 33-34

PAGES 35-36

PAGES 37-38

PAGE 39

PAGE 40

PAGE 41

PAGE 42

PAGE 43

TABLE OF CONTENTS

FABRICS

VACUUM BAGGING


FABRIC AIDS & STORAGE

MIXING, SAFETY & CLEANUP

RESIN & ADDITIVES

WIND ENERGY

CHROMAVEILTM

RESIN APPLICATORS

BOOKS & VIDEOS

PG. 1

PG. 19

PG. 29

PG. 32

PG. 37

PG. 12

PG. 27

PG. 31

PG. 35

PG. 43

FABRICS

WWW.FIBREGLAST.COM 1 .800.330.6365 SAME DAY SHIPPINGP A T T E R N E D C A R B O N F I B E R1 Purchase online or get more data at www.fibreglast.com

CREATE A PIECE OF ART WITH THE STRENGTH OF CARBON FIBER.

Carbon Fiber Patterns Carbon fiber fabrics have never looked like this before! Each pattern is unique and exciting. Not only do these patterns look awesome when laminated; they retain the weight and strength properties of a regular carbon fiber fabric. These fabrics are First Quality guaranteed, so you can work with confidence knowing your part will look and perform great!

ROOK GRANDMASTERCARBON FIBER - 3K, 12x12, 5.7 Oz/YD2, 50” WIDE, .014” THICK CARBON FIBER - 12K, 10x10, 19.2 Oz/YD2, 50” WIDE, .03” THICK

Custom Cut - min. qty of 10 yds. Item #: 322010+ yds $54.95 /yard25+ yds $51.95 /yard50+ yds $48.95 /yard100+ yds $45.95 /yard


Pre-Cut Length Price/Roll Item #1 yd roll $64.95 3220-A3 yd roll $184.95 3220-B5 yd roll $289.95 3220-CSwatch (4”x 6”) $2.95 3220-SWATCH


This pattern captures the sophisticated appeal of a chessboard and the excitement of a checkered flag. This fabric has multiple dimensions. At certain viewing angles, this pattern has a high-contrast chessboard look. At other viewing angles, each square turns into a subtle diamond. Use this carbon fiber to achieve an exceptionally unique part.

This brawny, 12K carbon fiber is the champion. Its bold, plain weave construction creates a lustrous, glazed chessboard. Every thick yarn of carbon is like a glossy brushstroke. The high-contrast surface makes for brilliant highlights but also deep, dark shadows. Use this fabric on a car hood, a motorcycle fender, a snowboard or any project that needs something strong and bold.

*ROOK

FABRICS


P A T T E R N E D C A R B O N F I B E R2

LABYRINTH

ROSWELL

WASP

ATOMIC

CARBON FIBER - 3K, 12x12, 5.7 Oz/YD2, 50” WIDE, .014” THICK












Laminating this carbon fabric really makes the pattern come alive. This pattern is like an optical illusion. In certain light, a maze of cubes zigzag the length of the fabric. The pattern seems to reach crookedly into the third dimension, fascinating anyone who looks upon it.

This carbon fiber fabric is out of this world. This pattern is open to visual interpretation, but one thing is certain, it is captivating. Oblique circles and squares extend the length of the fabric, creating a texture that looks like diamond plate. Different lighting on this carbon reveals sharp contrast and depth that has never been seen before in a carbon fiber fabric.

This hexagon covered pattern is like an intimidating, scaly predator. Each honeycomb is well-defined and would look great in any application. The polygonal shapes lock together to create a harmonious, symmetrical pattern. Lay up a car hood, a dashboard or a table. This incomparable fabric is just what you need to stand out.

Small yet powerful, this pattern displays carbon fiber fragments with rich, complex detail. This fabric changes in the light like a hologram. When viewed at a certain angle, small diamond shapes are visible. When laminated, the shifty, lustrous pattern creates an extraordinarily sleek surface.

PATTERNED CARBON FIBER SAMPLE PACKThis convenient Sample Pack contains a 12”x 12” Swatch of every patterned carbon fiber. It is ideal for determining which fabric you would like to try for your next application. Plus, this Sample Pack includes a coupon for $25 off your next order of $100 or more when purchased within 60 days!

Price Item #$19.95 4006-A

FABRICS

WWW.FIBREGLAST.COM 1 .800.330.6365 SAME DAY SHIPPING

3K, 2x2 TWILL WEAVE CARBON FIBER

PREPREG 3K, 2x2 TWILL WEAVE CARBON

6K, 5HS WEAVE CARBON FIBER FABRIC

CARBON FIBER VEIL

1K, PLAIN WEAVE ULTRALIGHT CARBON FIBER FABRIC

3K, PLAIN WEAVE CARBON FIBER FABRIC

5.7 oz/sq yd, 50” Wide, .012” Thick, 3K, 2x2 Twill Weave. This 2x2 twill weave fabric offers the cosmetic appearance so desirable on modern composite parts. But don’t just use it for looks, this fabric is highly formable and slightly stronger than the plain weave.


Custom Cut - min. qty of 10 yds. Item #: 236310+ yds $169.95 /yard26+ yds $164.95 /yard




Custom Cut - min. qty of 10 yds. Item #: 310110+ yds $118.75 /yard25+ yds $113.25 /yard50+ yds $107.75 /yard75+ yds $102.25 /yard100+ yds $96.75 /yard






Pre-Cut Length Price/Roll Item #1 yd roll $175.95 3101-A3 yd roll $439.95 3101-B5 yd roll $654.45 3101-C

50” Wide. Our most popular carbon in prepreg form. Identical to part# 1069, this prepreg offers the advantages of pre-impregnation of an epoxy resin system. The material can be stored, shipped and handled at room temperatures and is cured using ramp up schedule requiring at most 310°F. Resin content 33.00% - 39.0%

5.7 oz/sq yd, 50” Wide, .012” Thick, 12.5 x 12.5 Plain Weave. This plain weave carbon fiber is the most commonly used type for lightweight aerodynamic parts. Only three layers are typically necessary to produce non-structural pieces. It wets out quickly and handles easily.

3.5 oz/sq yd, 42” wide, .009” thick.This unique carbon fabric is used in the most demanding applications requiring carbon properties and stiffness at a minimum weight. Plain weave construction provides excellent stability and easy handling.

10.9 oz/sq yd, 50” Wide, .024” Thick, 6K, 5HS Weave Construction. With twice the fiber density of the 3K types, this fabric is ideal for structural applications. Also, the 5HS weave allows it to work even with the most complex shapes. This material builds quickly to form lightweight structures with virtually no flex.

Purchase online or get more data at www.fibreglast.com

.2 oz, 35.5” Wide. Graphite veils are frequently used in applications when corrosion resistant barriers are required. The nonwoven construction allows a resin-rich surface that

increases chemical stability and reduces the risk of micro-cracks forming in the composite surface. Carbon veils can also be used for grounding a composite structure, minimizing the build-up of static electricity that could prove dangerous when in contact with explosive liquids and gases.

C A R B O N F I B E R3

FABRICS


CARBON FIBER TAPE

BRAIDED CARBON BIAXIAL SLEEVES

UNIDIRECTIONAL CARBON FABRIC

24K CARBON FIBER TOW

CARBON FIBER SAMPLE PACK


Custom Cut - min. qty of 10 yds. Item #: 259610+ yds $19.95 /yard25+ yds $17.95 /yard50+ yds $15.95 /yard





Pre-Cut Length Price/Roll Item #1” - 10 yd roll $54.95 597-A1” - 50 yd roll $229.95 597-B2” - 10 yd roll $69.95 596-A2” - 50 yd roll $259.95 596-B3” - 10 yd roll $84.95 2402-A3” - 50 yd roll $304.95 2402-B4” - 10 yd roll $99.95 598-A4” - 50 yd roll $349.95 598-B6” - 10 yd roll $129.95 2415-A6” - 50 yd roll $504.95 2415-BSwatch (1” x 6”) $2.95 597-SWATCH

1-1/2” Wide, 8.3 oz/sq. yd., 3K, .013” ThickPre-Cut Length Price/Roll Item #1 yd roll $29.95 2608-A3 yd roll $74.95 2608-B5 yd roll $104.95 2608-C

4.3 oz/sq. yd., IM, 12K, .006” Thick, 12” WidePre-Cut Length Price/Roll Item #1 yd roll $39.95 2596-A3 yd roll $99.95 2596-B5 yd roll $144.95 2596-C

9 oz/sq. yd., 12K, .014” Thick, 12” WidePre-Cut Length Price/Roll Item #1 yd roll $29.95 2583-A3 yd roll $74.95 2583-B5 yd roll $104.95 2583-C

2” Wide, 7.5 oz/sq. yd., 3K, .03” ThickPre-Cut Length Price/Roll Item #1 yd roll $29.95 2609-A3 yd roll $74.95 2609-B5 yd roll $104.95 2609-C




Plain weave, 3K, 5.7 oz/sq yd and .012” Thick. Graphite Tapes are ideal for selective reinforcement of graphite fabrications, sleeve winding, lap joining, and repairs of cracks on graphite surfaces.

No Seams, No WindingThese braided carbon biaxial sleeves have the cosmetically desirable appearance of a 2x2 Twill pattern but as a sleeve, they can be slid over a prepared mandrel or tube to create straight or tapered tubing. The sleeves can be increased from their base diameter up to 30% and decreased up to 70%. This means that a 2” diameter can be used in a single application ranging from 2.6” diameter down to 0.6”. Laying up sleeves is predictable, repeatable and suitable for precise manufacture of composite parts.

9.0 oz/sq yd, 12K, .014” thick & 4.3 oz/sq yd. IM, 12K, .006” thick. This unidirectional is made without the typical hot melt process. Consequently, there is no crimping of the fibers and only minimal binder is used. This results in the highest property unidirectional dry reinforcement available. The 9 oz is used in many marine applications such as boat hulls, as well as hockey sticks and bicycles. The Intermediate Modulus 4.3 oz Uni is used in aerospace and racing applications where maximum single directional properties are critical. 12” wide.

Selectively Reinforce Fiberglass, Kevlar® and Carbon. Our high strength Carbon Tow is for selectively reinforcing fiberglass or carbon and for fabricating small, high strength, low weight structures. Use to filament wind tubes or add as a dense charge for compression molding.

This convenient Sample Pack contains 4”x 6” swatches of all of our carbon fabrics. It is ideal for determining which material you would like to try for your application. Plus, this Sample Pack includes a coupon for $25 off your next order of $100 or more when purchased within 60 days!


C A R B O N F I B E R4

Williams Racing & DevelopmentCentreville, VA

FABRICS

WWW.FIBREGLAST.COM 1 .800.330.6365 SAME DAY SHIPPINGK E V L A R ®

5

KEVLAR® TWILL WEAVE FABRIC

KEVLAR® / CARBON HYBRIDS

PREPREG 2x2 TWILL WEAVE KEVLAR®KEVLAR® PLAIN WEAVE FABRIC

5.0 oz/sq yd, 50” wide, 2x2 Kevlar® Twill FabricThis Kevlar® fabric provides the improved cosmetics and drapability of a twill weave. Ideal for impact resistant applications requiring the lightweight, high strength properties of Kevlar® where pattern show-through is desirable.

5.4 oz/sq yd, 50” Wide, .012” Thick, 2x2 Twill WeaveThese first quality, hybrid fabrics offer 3K Carbon in the warp and 1500 Denier Kevlar® in the fill directions for maximum drapability and drop-dead good looks. Use as a single layer for cosmetics only or back with another layer in the cross direction for a maximum balance of properties. The Kevlar® fibers are dyed with red, blue or yellow dyes for eye-catching color.


Custom Cut - min. qty of 10 yds. Item #: 1067 (Red), 1066 (Blue), 1065 (Yellow)10+ yds $44.00 /yard25+ yds $35.10 /yard50+ yds $31.50 /yard




Pre-Cut Length Price/Roll1 yd roll $59.95 3 yd roll $169.95 5 yd roll $249.95 Swatch (4”x 6”) $2.95



50” Wide, Impact Resistance, Twill Pliability This Prepreg is identical to part# 2443, Twill Weave Kevlar® but is pre-impregnated with an epoxy resin system. This material can be stored, shipped and handled at room temperatures and is cured using a ramp up schedule requiring at most 310°F. Resin content 36% - 42%

5.0 oz/sq yd, 50” wide, Kevlar® Plain Weave Fabric. Kevlar® in plain weave form is the most popular Kevlar® in composites. Although it is a little stiff for highly contoured molds, it offers uniform properties, maximum stability and simple surfacing characteristics. Good stiffness, light weight and high abrasion resistance.


Item # (Red)1067-A 1067-B 1067-C 1067-SWATCH

Item # (Blue)1066-A 1066-B 1066-C 1066-SWATCH

Item # (Yellow)1065-A 1065-B 1065-C 1065-SWATCH

KEVLAR® AND HYBRID SAMPLE PACKThis convenient Sample Pack contains 4”x 6” swatches of all of our Kevlar® and Hybrid fabrics. It is ideal for determining which material you would like to try for your application. Plus, this Sample Pack includes a coupon for $25 off your next order of $100 or more when purchased within 60 days!


David McHughColmesneil, TX

FABRICS


K E V L A R ®

6

KEVLAR® 4HS WEAVE FABRIC

KEVLAR® VEIL

HELPFUL INFORMATION

5 oz/sq yd, 50” Wide, .012” Thick, 17 x 17 4HS WeaveKevlar® in 4HS is often preferred for maximum conformability. 4HS construction means that one filling thread (width) floats over 4 warp (length) threads resulting in a fabric that looks different on each side and a lot of flexibility in design.

.25 oz, 35.5” Wide Kevlar® veil is a lightweight, nonwoven material that helps block print-through while still offering abrasion and impact resistance. Though commonly used in Kevlar® laminates, it can also be paired with carbon fiber or fiberglass to provide the benefits of Kevlar® while adding minimal weight and thickness.

• Raw Kevlar® fabric is not UV Stable. When storing raw Kevlar® fabric, cover it with a dark cloth to prevent deterioration.• Fibre Glast only carries Kevlar® 49 (non-ballistic)• Kevlar® is abrasion resistant. Keep a separate pair of scissor just for Kevlar®. See the Gingher Serrated Scissor on Page 33.







KEVLAR® TAPE

2” BRAIDED KEVLAR®

BIAXIAL SLEEVE

1” WidePre-Cut Length Price/Roll Item #10 yd roll $27.45 531-A50 yd roll $98.95 531-B





5 oz/sq yd, .0100” Thick, 17x17 Plain Weave. Kevlar® tape is ideal for selective reinforcement of Kevlar®, fiberglass or carbon laminations and repairs. This plain weave style offers optimum stability and drapeability for wrapping or laying in strips. Highly recommended in lieu of cutting Kevlar® into small strips.

2”, 9.9 oz/sqyd, 0.018” thick. This sleeve offers all of the benefits inherent in Kevlar®. Impact and abrasion resistant, this sleeve will also conform to shapes with changing geometries. Great for use in prosthetics, hockey sticks and much more. It can be slid over a prepared mandrel or tube to create straight or tapered tubing. Biaxial sleeves can be increased from their base diameter up to 30% and decreased up to 70%. This means that a 2” diameter can be used in a single application ranging from 2.6” diameter down to 0.6”. Laying up sleeves is predictable, repeatable and suitable for precise manufacture of composite parts.

Quantity Discount - Item #: 531-B4+ $94.55 /roll10+ $90.15 /roll



Item # 1731-AGingher Serrated Scissor

Kevlar® is a registered trademark of E.I. Dupont De Nemours & Co.

FABRICS

WWW.FIBREGLAST.COM 1 .800.330.6365 SAME DAY SHIPPINGF I B E R G L A S S7

STYLE 7781 E-GLASS9 oz/sq yd, 38” Wide, .008” Thick, 57 x 54, 8H Satin WeaveFrequently specified in aerospace applications, this fabric offers excellent strength, formability, and surfacing characteristics. Meets MIL-C-9084C, Type VIII-B.



PREPREG 7781 E-GLASS



50” Wide, 8H Satin Weave This fabric is identical to part# 543, 7781 E-Glass but is pre-impregnated with an epoxy resin system. The material can be stored, shipped and handled at room temperatures and is cured using a ramp up schedule requiring at most 310°F. Resin content 27.0% - 33.0%

STYLE 120 E-GLASS

BI-DIRECTIONAL E-GLASS

UNIDIRECTIONAL E-GLASS

STYLE 6781 S2-GLASS






Pre-Cut Length Price/Roll Item #1 yd package $16.45 1093-A3 yd package $43.95 1093-B5 yd package $65.95 1093-CSwatch (4”x 6”) $1.95 1093-SWATCH



3 oz/sq yd, 38” Wide, .0035” Thick, 60 x 58, 4H Satin Weave. This fabric is extremely tightly woven and is commonly used in aerospace and high quality fabrications. Meets MIL-C-9084C, Type III.

Style 7725, 9 oz/sq yd, 38” Wide, .008” Thick, 2x2 Twill Weave. This high performance, loose weave, 2 x 2 twill fabric is both strong and formable. When cut off the roll on a 45 degree bias, it will drape over virtually any contour. It was developed for the light aircraft market, but it can be used anywhere high strength, fast wet-out, and drapability are desired.

Style 7715, 7 oz/sq yd, 38” Wide, .008” Thick, 80 x 18 Plain Weave. Unidirectional fabrics are used to strengthen in one direction and save weight in the less critical orientation. This fabric permits a part’s strength to be tailored to any orientation or stiffness with little weight penalty. #1093 is a plain weave style with 95% of the fiber density in the warp (roll length) direction.

9 oz/sq yd, 50” Wide, .009” thick, 57 x 57 construction, 8H Satin Weave. This Style 6781 S2-Glass is identical to the Style 7781 E-Glass (#543) except it is woven with superior S-2 fibers resulting in extraordinary strength with a superior look and finish.


FABRICS


F I B E R G L A S S8




Pre-Cut Length Price/Roll Item #1 yd package $7.65 241-F3 yd package $18.65 241-A5 yd package $27.45 241-BSwatch (4”x 6”) $1.95 241-SWATCH

Pre-Cut Length Price/Roll Item #1 yd package $12.05 262-F3 yd package $27.45 262-B5 yd package $38.45 262-CSwatch (4”x 6”) $1.95 262-SWATCH


2 Oz FABRIC

4 Oz FABRIC

6 Oz FABRIC

2 oz/sq yd, 38” Wide, .004” Thick, 32 x 38 Plain Weave. This fabric is easy to handle and also provides an excellent finish. It is highly drapable and cures to a transparent protective barrier. Also perfect as a sanding veil over Kevlar®.

4 oz/sq yd, 50” Wide, .006” Thick, 24 x 22 Plain Weave. The most frequently used surfacing fabric. This is commonly used to stop print through when backed by layers of heavier fabric in molded parts. Great for strip built canoes and final layering over moldless designs.

6 oz/sq yd, 38” Wide, .007” Thick, 18 x 18 Plain Weave. 2-3 Layers of this fabric is a popular lightweight molding schedule and repair sequence. A single layer also provides more protection to strip built canoes, and is still quite clear.

7.5 Oz FABRIC

10 Oz FABRIC

7.5 oz/sq yd 38” and 50” Wide .011” Thick, 16 x 14 Plain WeaveCommonly called “Boat Cloth”, this fabric is excellent for covering plywood, plug shapes, and moldless foam designs. 1-2 layers will waterproof and protect boat floors and roofs.

10 oz/sq yd 38”, 50” and 60” Wide .014” Thick, 16 x 14 Plain Weave. Frequently used in mold building, sandwich core panels, and high strength lay-ups. 8 plies of 10 oz fabric will produce a strong 1/8” laminate weighing 1 lb per sq ft. This Style 7500 fabric meets MIL-C-9084C, XII-A.

38” WidePre-Cut Length Price/Roll Item #1 yd package $10.95 243-F3 yd package $24.15 243-A5 yd package $36.25 243-B

38” WidePre-Cut Length Price/Roll Item #1 yd package $15.35 245-A3 yd package $36.25 245-B5 yd package $49.45 245-C









Swatch (4” x 6”) $1.95 4011-SWATCH

FABRICS


WOVEN FIBERGLASS TAPESReinforcement for Edges, Avoid Fraying When Narrow Strips are Needed. These narrow widths of fiberglass find many applications in selectively reinforcing edges, seams of molding, laminations, and pipe winding applications. The fully seamed edges avoid the problems caused by cutting narrow strips from fulll width fabrics. These tapes saturate easily and in most respects are similar to a 10 oz fabric. Plain weave construction.













Swatch (2” x 6”) $1.95 4010-SWATCH

20 Oz TOOLING FABRIC

BLACK FIBERGLASS

ALUMINIzED FIBERGLASS FABRIC

2” BRAIDED FIBERGLASS BIAXIAL SLEEVE







20 oz/sq yd, 38” Wide, .026” Thick, Mock Leno Weave. This fabric offers very high strength characteristics as well as rapid build-up. Apply to molds as a back-up shell once the finer surfacing layers are in place.

50” Wide, Twill WeaveBlack fiberglass is woven to look just like 3K Twill carbon fiber. Of course, it does not have any of the strength properties associated with carbon. Black fiberglass is generally about half the price of carbon and it is an ideal alternative to carbon for cosmetic applications.

8.7 oz/sq yd, 50” Wide, 0.0096” Thick, 2x2 Twill Weave.Achieve the ultimate, high-tech composite look with Aluminized Fiberglass. Used for cosmetics, this fabric contains a thin coating of 99.99% pure aluminum on one side to create a highly reflective surface and the appearance of woven metal. Frequently misrepresented as “silver carbon fiber”, this fiberglass fabric is used for adding extra flair to any composite project. Aluminized fiberglass is compatible with all of our epoxy, polyester and vinyl ester resin systems.

2”, 10.4 oz/sqyd, 0.011” thick. This sleeve will conform to shapes with

changing geometries. Great for use in prosthetics, hockey sticks and much more. It can be slid over a prepared mandrel or tube to create straight or tapered tubing. Biaxial sleeves can be increased from their base diameter up to 30% and decreased up to 70%. This means that a 2” diameter can be used in a single application ranging from 2.6” diameter down to 0.6”. Laying up sleeves is predictable, repeatable and suitable for precise manufacture of composite parts.




FABRICS


F I B E R G L A S S10

CONTINUOUS STRAND VEIL SURFACING

SCRIM FABRIC, WHITE

CONTINUOUS STRAND MAT

MAT TAPE


Custom Cut - min. qty of 10 yds. Item #: 24610+ yds $4.05 /yard25+ yds $3.75 /yard50+ yds $3.55 /yard100+ yds $3.25 /yard250+ yds $2.95 /yard500+ yds $2.55 /yard Custom Cut - min. qty of 10 yds. Item #: 251

10+ yds $7.65 /yard25+ yds $7,25 /yard50+ yds $6.65 /yard125+ yds $6.35 /yard500+ yds $5.75 /yard

Pre-Cut Length Price/Roll Item #1 yd roll $6.55 260-F3 yd roll $17.55 260-G5 yd roll $21.95 260-HSwatch (4”x 6”) $1.95 260-SWATCH



Pre-Cut Length Price/Roll Item #10 yd roll $7.65 492-C90 yd roll $54.95 492-DSwatch (4”x 6”) $1.95 492-SWATCH

38” Wide, .010” ThickThis lightweight mat is typically used as a surfacing layer on laminations to improve surface finish and to provide a resin rich area in corrosion resistant tank linings.

50” Wide, .005” ThickScrim cloth can be used in repair applications or for reinforcement of other types of materials including fiberglass, concrete and some plastics. When fully cured, the scrim cloth will add reinforcement and mimic the expansion and contraction of the surrounding substrate.

1-1/2 oz/sq ft. Mat, 50” Wide, .060” ThickContinuous strand mats are frequently used when rapid build-up and high conformability is required. When used for vacuum infusion, continuous strands will facilitate resin flow without the slowing effect frequently caused by chopped strand binders. 1.5 oz.

1-1/2 oz/sq ft. Mat, 50” Wide, .060” Thick. Continuous strand mats are frequently used when rapid build-up and high conformability is required. When used for vacuum infusion, continuous strands will facilitate resin flow without the slowing effect frequently caused by chopped strand binders.

CHOPPED STRAND MAT: 1.5 Oz1-1/2 oz/sq Ft. Mat, 38” & 50” Wide, .045” ThickMat can be used alone or in conjunction with fiberglass fabrics or woven roving in larger fabrications. Mat is commonly used for buildup such as plywood decking and between layers of fabric when molding. Our mats both meet MIL-M-43248C, Type 1, Class 2, Grade A. Chopped strand mat contains a binder which prevents proper bonding with any epoxy resins. Use our polyester or vinyl ester resins with chopped strand mat.



38” WidePre-Cut Length Price/Roll Item #1 yd package $10.95 250-A3 yd package $27.45 250-B5 yd roll $38.45 250-CSwatch (4”x 6”) $1.95 250-SWATCH

50” WidePre-Cut Length Price/Roll Item #1 yd roll $14.25 1250-A3 yd roll $32.95 1250-B5 yd roll $49.45 1250-C

SEE SAERTEX® STITCHED FABRICS ON PAGE 27.

FABRICS


WOVEN ROVING

GUN ROVING

CHOPPER GUN

18 oz/sq yd, 50” Wide, .025” ThickWoven Roving is used in laminating large fiberglass parts such as boats and tanks where an inexpensive, high impact, high strength reinforcement is required. Woven roving should be used with mat whenever bonding to plywood or making repairs.

Chops Cleanly and Wets CompletelyAvailable in 40 lb rolls, this gun roving feeds through our #1171-A Air Chopper Gun and is designed for use in all polyester spray up systems, both filled and unfilled.. This versatile roving chops cleanly, wets rapidly and completely. Yields approximately 205 yards per pound.


Pre-Cut Length Price/Roll Item #1 yd package $16.45 223-F3 yd roll $43.95 223-A5 yd roll $54.95 223-BSwatch (4”x 6”) $1.95 223-SWATCH

Description Price Item #40 lb Roll $148.45 522-ACase (4 Rolls) $534.55 522-BSkid (12 Rolls) $1,534.45 522-CSwatch $1.95 522-SWATCH

Quick Glass Build UpA hand held, variable speed air powered chopper gun for coating molds or parts with

glass reinforcement. Continuous glass roving is fed into the rear of the gun. The gun then chops the roving into short pieces and deposits them onto the mold. Resin is then applied by brush, roller or sprayed on using a cup gun. The length of the fibers can be varied from 4” down to 5/16”. This gun will deposit the equivalent of one layer of 1 oz mat onto a vertical surface without fall-off before wet-out. Ideally suited to quick mold or part build-up once the first layer or two are in place. Use a saturation roller to remove trapped air. New design increases cutter head surface by 32% and increased quantity of chopped material between blade replacements by 33%. Works with #522 Gun Roving or #2293 24K Carbon Tow

Item # Price1171-A $399.95

LAMINATE BULKERS



2mmPre-Cut Length Price/Roll Item #1 yd roll $9.95 2258-A3 yd roll $24.95 2258-B5 yd roll $39.95 2258-CSwatch (4”x 6”) $1.95 2258-SWATCH

4mmPre-Cut Length Price/Roll Item #1 yd roll $19.95 2259-A3 yd roll $54.95 2259-B5 yd roll $79.95 2259-CSwatch (4”x 6”) $1.95 2259-SWATCH

2mm & 4mm, 39.4” Wide Lightweight alternative to multiple layers of fiberglass! The 2mm and 4mm Laminate Bulkers are made out of fine polyester, non-woven, multi-directional fibers that provide equal strength characteristics in both the length and width directions. By allowing easier resin distribution through-

out a part, these Laminate Bulkers act as strong interlaminate links between different layers of reinforcement. Also, Laminate Bulker materials add screw retention capabilities to laminate parts. Compared to bulk laminating with fiberglass, these Laminate Bulkers provide tremendous weight savings. With-stands severe duty fatigue, low resin consumption, excellent impact barrier, low shrinkage, superior shear strength, prevents stress cracks on gel coated parts, maintains a constant thickness, Easy to use.

FIBREGLASS SAMPLE PACKThis convenient Sample Pack contains a 4” x 6” swatch of all of our fiberglass fabrics and tapes. It is ideal for determining which material you would like to try for your application. Plus, each sample pack includes a coupon for $25 off your next order of $100 or more when purchased within 60 days!



Elite CustomzCincinnati, OH


RESIN & ADDITIVES


E P O X Y R E S I N12

SYSTEM 2000 EPOXY RESINSystem 2000 Epoxy Resin is a medium viscosity, light amber laminating resin that is designed for fabricating parts and other demanding structural applications. Use this system to maximize the physical properties of carbon fiber, Kevlar®, and glass laminates! Test results have proven superiority over other room temperature epoxies. Its low viscosity and great handling characteristics make it a favorite in the shop too!

Three high performance hardener systems are available for the System 2000 resin. 20 minute, 60 minute and 120 minute pot life versions are all options. This added variety allows the fabricator to select the system best suited to the size, complexity, or time-frame of the project. Simple parts which need to be demolded quickly should use the 20 minute hardener. Larger and more complex parts can use either of the other hardeners.

Vacuum Bagging applications would typically warrant the longest 2 hour working time. As with any epoxy system, adhere to the proper mix ratios and maintain an adequate curing temperature of at least 70 degrees F. The cure time will be cut in half for every 10 degrees F that the temperature is raised above 70 degrees F. Purchase a single cure, or buy resin in bulk and order a variety of hardeners to keep on hand for any project.

Chopped strand mat contains a binder which prevents proper bonding with any epoxy resins. Use our polyester or vinyl ester resins with chopped strand mat.

First, select the amount of System 2000 Resin that you will need. Then select your needed curing agent or combination of curing agents. Remember, these are not exact kits, so be sure you have enough Hardener!

Description Price Item #Quart (2 lbs) $44.95 2000-AGallon (8 lbs) $104.95 2000-B5 Gallon Pail (40 lbs) $395.95 2000-C

Description Price Item #1/2 Pint (0.5 lb) $21.95 2020-AQuart (2 lbs) $44.95 2020-BGallon (8 lbs) $129.95 2020-C



2020 EPOXY HARDENER

2060 EPOXY HARDENER

2120 EPOXY HARDENER

20 Minute Pot LifeShort 20 minute pot life is quite versatile. Use for repairs, simple fabrications, or those parts requiring a quick de-mold time.

Pot Life: 20 MinutesMix Ratio By Weight: 100:23Mix Ratio By Volume: 4:1

60 Minute Pot LifeThis medium pot life hardener is ideal for standard part fabrication. The one hour working time eases frantic lay-up schedules and improves quality of most parts. Post cured temperature exceeds 200 degrees F


120 Minute Pot LifeThis long pot life hardener extends working time on large-scale and complex projects. Suitable for vacuum bagging and laminating in hot climates. The 24-36 hour de-mold time can be reduced by increasing the cure temperature. The post-cured service temperature exceeds 200 degrees F.


Quantity Discount - Item #: 2000-C4+ $359.95 /5 Gallon Pail10+ $349.95 /5 Gallon Pail

Quantity Discount - Item #: 2020-C4+ $127.95 /Gallon10+ $124.95 /Gallon



HELPFUL INFORMATION• This epoxy does not contain a UV inhibitor. Protect System 2000 Epoxy from direct sunlight.• Cannot be used with Chopped Strand Mat

MotoPOD LLCPoplar Grove, IL


RESIN & ADDITIVES

E P O X Y & V I N Y L E S T E R R E S I N13

EPOXY SURFACE COAT

EPOXY PASTE BONDING ADHESIVE

LIGHTWEIGHT EPOXY FILLER

A white, thickened epoxy material used to create the durable surface coat on room temperature epoxy molds. This surface coat can be brushed on as thick as 1/8” at a time without developing runs or sags. It is specially formulated to provide strong interlaminar bonds with the reinforcing materials, even if it is left unsupported overnight. #1099 resists chipping and cracking, and retains its high gloss.

High strength structural adhesive used to bond and assemble sub-components to form rigid final structures. The high viscosity provides excellent gap filling characteristics that strengthen loose fitting joints and panels. #1101 forms tough durable bonds to composites,

SMC, many metals, and even common construction materials. It is easy to use with its 1:1 mix ratio, and 6-8 hour cure time at 77 degrees F.

Extremely lightweight epoxy filler used to smooth the surface of repaired parts, fill the weave on moldless or male molded parts, and shape fillets in corners and joints. This epoxy filler provides superior adhesion to most surfaces including SMC, and exhibits no shrinkage. It spreads smoothly with few sags, even upside down! Final contours are easily sanded with standard shop tools.

Description Price Item #Quart Kit $59.95 1099-ACase (6 Quart Kits) $309.95 1099-B



Quantity Discount - Item #:1099-B4+ $284.95 /Case (6 Quart Kits)



VINYL ESTER RESINTough and Corrosion ResistantThis vinyl ester resin is formulated for maximum corrosion resistance to most fuels, vapors, and both acidic and basic chemicals. It is also heat resistant and blended for toughness. These qualities make it perfect for repairing tank linings, blistering boat hulls, as well as fabricating tough all-around parts. Shelf Life Limited to 3 months. (Hetron 922) Formulated for 1.25% MEKP.

1110/69-F kit contains (1) QUART RESIN, (1) 69-A.1110/69-A kit contains (1) GAL RESIN, (2) 69-A.1110/69-AK kit contains (4) GAL RESIN, (8) 69-A.

Resin Kit (with hardener)Description Price Item #Quart w/ hardener $39.95 1110/69-FGallon w/ hardener $84.95 1110/69-ACase (4 Gallons w/ hardener) $299.95 1110/69-AK

ResinDescription Price Item #Quart (2 lbs) $37.95 1110-FGallon (9 lbs) $82.95 1110-A5 Gallon Pail (40 lbs) $319.95 1110-BQuantity Discount - Item #: 1110-B4+ $309.95 /5 Gallon Pail10+ $295.95 /5 Gallon Pail

HELPFUL INFORMATION• Vinyl Ester Resin exceeds both polyester and epoxy resin in corrosion resistance, temperature resistance, and elongation (toughness).

• Vinyl Ester Resin has a 3 month shelf-life.

• Vinyl Ester Resin catalyzes with #69 MEKP on page 16.

Double Dog MotoSan Francisco, CA


RESIN & ADDITIVES


P O L Y E S T E R R E S I N14

POLYESTER MOLDING RESIN ISOPHTHALIC POLYESTER RESIN

POLYESTER LAMINATING RESIN

Wax Free, General Purpose Resin#77 Molding Resin is ideal for general purpose part fabrication and for building low cost molds. An internal thickening agent has been added to prevent drainage on vertical surfaces, yet it retains the low viscosity required for rapid wet out. This resin is wax free to reduce sanding between coats. Formulated for 1.25% MEKP.


Durable and Stable Resin#90 Iso Polyester is perfect for making dimensionally stable polyester molds, corrosive service part fabrication, and as a durable repair material for tank linings. #90 permits fast wet-out in spray or hand laminates. It’s 225 degree F service temperature also resists exotherm and post cure problems. Properly fabricated parts may be used in food contact applications. Formulated for 1.25% MEKP.


Waxed for Top or Finish Coats#83 is a waxed resin for laminating thin fiberglass skins on plywood, or for general purpose fiberglass repairs. The wax in the resin will prevent surface tackiness even when applied in thin coats. Sand off the wax layer before painting or secondary bonding. Stir thoroughly in can before using. Formulated for 1.25% MEKP.

83/69-A kit contains (1) QUART RESIN, (1) 69-A.83/69-AK kit contains (12) QUARTS RESIN, (12) 69-A.83/69-B kit contains (1) GAL RESIN, (2) 69-A.83/69-BK kit contains (4) GAL RESIN, (8) 69-A.

Resin Kit (with hardener)Description Price Item #Quart w/ hardener $29.95 77/69-FGallon w/ hardener $59.95 77/69-ACase (4 Gallons w/ hardener) $219.95 77/69-AKResin Kit (with hardener)

Description Price Item #Quart w/ hardener $34.95 90/69-FGallon w/ hardener $69.95 90/69-ACase (4 Gallons w/ hardener) $264.95 90/69-AK

Resin Kit (with hardener)Description Price Item #Quart w/ hardener $34.95 83/69-ACase (12 Quarts w/ hardener) $329.95 83/69-AKGallon w/ hardener $64.95 83/69-BCase (4 Gallons w/ hardener) $249.95 83/69-BK

ResinDescription Price Item #Quart (2 lbs) $27.95 77-FGallon (9 lbs) $54.95 77-A5 Gallon Pail (40 lbs) $199.95 77-BResin

Description Price Item #Quart (2 lbs) $32.95 90-FGallon (9 lbs) $64.95 90-A5 Gallon Pail (40 lbs) $264.95 90-B

ResinDescription Price Item #Quart (2.2 lbs) $29.95 83-AGallon (8.8 lbs) $59.95 83-B5 Gallon Pail (40 lbs) $219.95 83-C

Quantity Discount - Item #: 77-B4+ $194.95 /5 Gallon Pail10+ $189.95 /5 Gallon Pail

Quantity Discount - Item #: 90-B4+ $259.95 /5 Gallon Pail10+ $254.95 /5 Gallon Pail


HELPFUL INFORMATION• #77, #83 and #90 polyester resins all require #69 MEKP Hardener on page 16.

ODP Motorsport EngineeringCoeur d’Alene, ID


RESIN & ADDITIVES

G E L C O A T15

Industry Standard#182 White Gel Coat is a highly durable ISO gel coat and is the industry production standard for molding applications. Use as a sandable base coat for painting or polish to a high luster finish. Spray unthinned into molds using a cup gun or blend with

#1040 Duratec Hi-Gloss Additive when performing repairs. Approved for use in marine and sanitaryware applications. Formulated for 1.5% MEKP.


Extend the Durability of Molds Tooling Gel Coat is an abrasion resistant gel coat for making molds where gloss retention, superior hardness, exceptional craze resistance and minimum distortion are paramount. The life of a good polyester mold may be extended considerably by the use of tooling gel coat. For best results, build the film thickness to 20 -25 mils. #1040

Hi-Gloss Additive can be added to further upgrade the gloss. Formulated for 1.5% - 2.5% MEKP.

The “A” kit contains (1) QUART RESIN, (1) 69-A.The “B” kit contains (1) GAL RESIN, (3) 69-A.The “BK” kit contains (4) GAL RESIN, (12) 69-A.

Super High Gloss#180 Clear Gel Coat is a high performance, premium quality gel coat for both airless and air atomized spray applications. #180 offers UV light stability, excellent clarity, crack and chemical resistance. This deep, crystal-clear and

non-yellowing gel coat is compatible with underwater and water contact marine applications as well as sanitaryware such as showers and tubs. It is recommended to be used as a protective clear coat over Chromaveil, other colors or glitterflake. Blend with #1040 Duratec Hi-Gloss Additive when top coating. Formulated for 1.5% - 2.5% MEKP.


Color Consistency#184 Neutral Gel Coat is a high performance, premium quality gel coat formulated specifically for use with pigment to obtain superior color consistency and opacity. #184 cures to a brilliant gloss and is ideal for applications needing an

opaque, lustrous and colorful surface. #184 is compatible with underwater and water contact marine applications and for sanitaryware use. Blend with #1040 Duratec Hi-Gloss Additive when top coating. Formulated for 1.5% MEKP.

184/69-A kit contains (1) QUART RESIN, (1) 69-A.184/69-B kit contains (1) GAL RESIN, (3) 69-A.184/69-BK kit contains (4) GAL RESIN, (9) 69-A.

Gel Coat Kit (with hardener)Description Price Item #Quart w/ hardener $42.95 182/69-AGallon w/ hardener $89.95 182/69-BCase (4 Gallons w/ hardener) $319.95 182/69-BK Black Tooling Gel Coat Kit (with hardener)

Description Price Item #Quart w/ hardener $46.95 186/69-AGallon w/ hardener $149.95 186/69-BCase (4 Gallons w/ hardener) $534.95 186/69-BK

Orange Tooling Gel Coat Kit (with hardener)Description Price Item #Quart w/ hardener $46.95 188/69-AGallon w/ hardener $149.95 188/69-BCase (4 Gallons w/ hardener) $534.95 188/69-BK

Gel Coat Kit (with hardener)Description Price Item #Quart w/ hardener $42.95 180/69-AGallon w/ hardener $89.95 180/69-BCase (4 Gallons w/ hardener) $319.95 180/69-BK

Gel Coat Kit (with hardener)Description Price Item #Quart w/ hardener $42.95 184/69-AGallon w/ hardener $89.95 184/69-BCase (4 Gallons w/ hardener) $319.95 184/69-BK

Gel CoatDescription Price Item #Quart (2 lbs) $39.95 182-AGallon (9 lbs) $84.95 182-B5 Gallon Pail (40 lbs) $319.95 182-C Black Tooling Gel Coat


Orange Tooling Gel CoatDescription Price Item #Quart (2 lbs) $44.95 188-AGallon (9 lbs) $144.95 188-B5 Gallon Pail (40 lbs) $549.95 188-C

Gel CoatDescription Price Item #Quart (2 lbs) $39.95 180-AGallon (9 lbs) $84.95 180-B5 Gallon Pail (40 lbs) $319.95 180-C

Gel CoatDescription Price Item #Quart (2 lbs) $39.95 184-AGallon (9 lbs) $84.95 184-B5 Gallon Pail (40 lbs) $319.95 184-C




WHITE GEL COAT TOOLING GEL COAT

CLEAR GEL COAT

NEUTRAL GEL COAT

Real Hot RodsLake Leelanau, MI


RESIN & ADDITIVES


D U R A T E C & R E S I N A D D I T I V E S16

Spray Gel Coat Like Paint #1040 can be mixed 1:1 with regular gel coat to reduce viscosity, porosity, and permit a complete open air cure. The reduction in viscosity allows gel coat to be sprayed controllably through siphon and HVLP equipment, reducing sanding and polishing time. Below the waterline repairs still need the addition of #71 Styrene Wax for maximum hardness. Requires 2% MEKP.

Industry Standard #69 MEKP is required with all Polyester Resins, Gel Coats and Vinyl Ester Resin. It is required in different concentrations as defined for each resin product. Each resin product is available as a kit with the correct amount of hardener. However, hardener may be purchased individually as shown here.

Perfect for Plug Finishing and Hiding Repairs Duratec Surfacing Primer is the best choice for coating your plug or reconditioning your mold.Thin 5%-15% if necessary to a desired spray viscosity with #2306 Duratec Thinner after catalyzing. This surface primer can be applied as heavily as 45 mils to fill fabric pores on plugs or over repairs. With a higher heat distortion temperature, shrinkage is reduced. This further hides the repair.The gray primer sands easily and is then buffed to a Class ‘A’ mirror finish before building the mold. Requires 2% MEKP.

Enhance the flow and leveling properties of #1041 Duratec Gray Surfacing Primer. This thinner reduces orange peel and porosity while allowing for a smoother spray flow.

General Purpose #70 Styrene Monomer is the recommended and accepted thinner for polyester resins and gel coats. Most gel coats can be thinned 2-5% to make them suitable for heavy spray equipment or other special purposes.

Get a Complete Cure # 71 Styrene Wax is a 5% solution of paraffin dissolved in styrene that may be added to non waxed polyester resins and gel coats to prevent the prolonged tackiness associated with thin sections of polyesters. If the resin contains paraffins, the wax will rise to the surface and protect the curing resin from the inhibiting action of the air. However, if the resin is allowed to fully cure, the paraffins on the surface will prevent adhesion of further coats of resin and must be sanded off prior to additional applications. We recommend adding #71 at 5% for thin coatings. Use with #1040 Hi-Gloss Additive when performing repairs below the water line.

DURATEC CLEAR HI-GLOSS GEL COAT ADDITIVE MEKP HARDENER

DURATEC GRAY SURFACING PRIMER

DURATEC THINNER

STYRENE THINNER

STYRENE WAX

Description Price Item #Gallon $119.95 1040-BCase (4 Gallons) $409.95 1040-C Description Price Item #

1 oz $2.95 69-AGallon $49.95 69-DCase (4 Gallons) $149.95 69-E

Description Price Item #Gallon $109.95 1041-BCase (4 Gallons) $364.95 1041-C

Description Price Item #Gallon $54.95 2306-ACase (4 Gallons) $189.95 2306-B

Description Price Item #Quart (2 lbs) $17.95 70-AGallon (7.5 lbs) $34.95 70-B

Description Price Item #Quart (2 lbs) $29.95 71-BGallon (7.5 lbs) $64.95 71-C

Quantity Discount - Item #: 1040-C4+ $374.95 /Case (4 Gallons)10+ $364.95 /Case (4 Gallons)

Quantity Discount - Item #: 1041-C4+ $334.95 /Case (4 Gallons)10+ $314.95 /Case (4 Gallons)

CATALYST CONCENTRATION CHARTVolume of catalyst to be used with Resins & Gel Coat (MEKP) Percent by Weight

Sacred SteelGreers Ferry, AR


RESIN & ADDITIVES

F I L L E R S , P I G M E N T S & G L I T T E R F L A K E17

Talc is the major component of any body filler. #131 is a sandable filler added for fairing and smoothing the finish of fiberglass laminations. The recommended filler ratio is 2 parts #131 to 1 part resin to result in a smooth, creamy semi-paste. The exact filler portion will vary by application depending on the desired consistency. Allow to stand one hour before adding hardener and using.

These hollow glass spheres make a lightweight sandable filler when blended with resin. Use to fill fabric weave, shallow blisters and surfaces of core materials. The average bubble is less than 70 microns, about a quarter of a grain of salt. It is this small particle size which makes the paste so easy to spread evenly.

These longer glass fibers are used to increase tensile and compressive properties of any resin, even concrete. This coarse mixture can strengthen castings and reinforce fillets in difficult to laminate areas of parts.

#38 is similar to #29 but the shorter fiber improves finishing characteristics for surface applications. Great to reinforce detailed castings, or blend with epoxy to make a tough outer surfacing coat.

These short fibers offer high strength results! Mix with any body filler or casting material to increase strength and reduce shrinkage. Blend with vinyl ester resin to create a strong and corrosion resistant blister repair putty for deeper hull damage, or blend with any of our resins to create a high strength repair. Mix to a ketchup consistency for best corrosion protection.

#23 is a fine grade fumed silica thickening agent similar to Cab-O-Sil and is added to resin systems to prevent run-off and sags on vertical surfaces. Mix in the ratio of 1 part by volume #23 to 2 parts resin for general use. Cab-O-Sil is a registered trademark of Cabot Corporation.

These precision chopped graphite fibers offer an economical alternative for localized reinforcement of high performance parts requiring optimal electrical conductivity, high strength and moduli. Excellent for reducing voids in difficult vacuum bagging applications. Spread the filler in deep cavities or sharp edges of parts and be assured the pressure will squeeze out air.

Kevlar® pulp is the lightest of the fillers and highly abrasion resistant. Areas of high impact can easily be reinforced with this strong and durable material. Also, use it to make beveled fillets along edges of honeycomb cores to smooth the transition of fabric skins. Recommended for use with epoxy or vinyl ester resin.

Our color pigments are pastes for tinting #184 Neutral Gel Coat, polyester, vinyl ester, epoxy resin and polyurethane foam. Pigments are added to the resin prior to the addition of catalyst. Our primary colors may be mixed to provide nearly any shade or hue. Keep an assortment of pigments on hand for color matching repairs or blending your own custom colors. When used to pigment our gel coats and resins, they are normally added at 6-8% by weight or ½ pint of pigment per gallon of resin. We have made every effort to accurately represent the cured color of our resins with these pigments.

Glitterflakes are commonly used to repair damaged bass boats or to make any project stand out from the crowd! These glitterflakes are .015” polyester flakes compatible with our #180 Gel Coat . By applying a layer of Clear into the mold followed by Clear with glitterflake, a metallic look is achieved. Typically the glitterflake is backed with a pigmented layer to opaque the fiberglass reinforcement.

TALC GLASS MICROSPHERESFILLERS

1/4” CHOPPED GLASS FIBERS

1/32” MILLED GLASS FIBERS

1/16” MILLED GLASS FIBERS

THIXOTROPIC SILICA

1/4” CHOPPED GRAPHITE FIBERS

KEVLAR® PULP

PIGMENTS GLITTERFLAKE

Description Price Item #1/2 Gallon (3 lbs) $6.25 131-ACarton (16 lbs) $11.45 131-BBox (50 lbs) $29.95 131-C

Description Price Item #1/2 Gallon (4 oz) $11.95 22-ACarton (3 lbs) $66.95 22-B

Description Price Item #1/2 Gallon (1.5 lbs) $16.95 30-ACarton (8 lbs) $39.95 30-BBox (50 lbs) $159.95 30-C

Description Price Item #1/2 Gallon (2 lbs) $19.95 38-ACarton (8 lbs) $49.95 38-BBox (25 lbs) $89.95 38-C

Description Price Item #1/2 Gallon (2 lbs) $19.95 29-ACarton (8 lbs) $49.95 29-BBox (25 lbs) $89.95 29-CBox (50 lbs) $149.95 29-D

Description Price Item #1/2 Gallon (6 oz) $9.95 23-ACarton (7 lbs) $119.95 23-CBox (30 lbs) $399.95 23-D

Description Price Item #1/2 Gallon (2 oz) $11.95 544-ACarton (1 lb) $59.95 544-BBox (10 lbs) $329.95 544-C

Description Price1/2 Pint $15.95Quart $54.95Gallon $199.95

#879Sparkling Silver

#883Gold

#882Red

#881Blue

Description Price4 oz $14.951 lb $35.954 lb $124.9510 lb $216.95

#867 #52 #2305 #42 #45 #46 #53 #63 #2232 #43 #41

Description Price Item #1/2 Gallon (1 lb) $59.95 571-ACarton (6 lbs) $264.95 571-B


RESIN & ADDITIVES


S P R AY G U N S18

Gel Coat Won’t Catalyze Inside The Gun An inexpensive gel coat gun for spraying small to medium size molds. Avoids the high cost of catalyst injector systems and at the same time avoids the pitfalls of a regular spray gun. The resin and catalyst are mixed in the disposable paper cups, the lid and nozzle assembly are pressed on, and the cup is then placed on the gun. With the paper cup in a level position, depress the trigger and the air stream picks up the gel coat and provides a uniform, high velocity spray pattern. To clean up, merely remove the cup form the gun, and just clean the lid and nozzle. Cup capacity is one quart. We ship the gun with a 3/16” ID nozzle, but others are available.

Pressure required –60 - 100 psiAir consumption – 5.8 CFM at 80 psi Compressor required – 5 HP Air connection - 1/4” TPR Dry weight – 2.0 lbs

Professional Grade This is a heavy duty gun offering a range of adjustments that will allow the spray pattern to be customized to the specific project. This gun excels at large surface spraying, such as new mold construction, composite refinishing and large boat repair. This gun comes fitted with a 2.5mm nozzle, which is ideal for any of our gel coats. Ships complete with 1.25 pint cup, cleaning brush, and 1 mini filter.

Pressure required – 40-80 psiAir consumption – 4.7-7.1 CFMCompressor required – 1.5 HPAir connection - 1/4” NPTDry weight – 1.55 LBS

This portable sprayer is perfect for misting coats of PVA Release Film over waxed mold surfaces. Use this versatile applicator for all kinds of liquids. Great economical alternative to other air-powered spray guns. Power Unit, Glass Reservoir and Caps SOLD SEPARATELY.

• Ready to spray in seconds with no batteries or hoses.• Simple for small projects and touch-ups.• Comparable performance to other professional airless sprayers.• Consistent spray flow for single pass coverage.• Professional Finish - Quality Results.

Easily Store Your Resin. #121, 1 Quart Reusable Plastic Tubs Graduated for Easy Measuring These plastic tubs will permit resin to stand without breaking down and permit acetone clean up. Ideal for cup gun applications where one cup after another is to be used. #887, 1 Quart Disposable Paper Tubs These disposable cups fit snugly on the gel coat cup gun and save messy clean up.

Perfect for Fluid Nozzles This simple tool will keep your gun spraying like new for years to come. It fits easily into the fluid nozzle to clean out any remaining gel coat. Speeds cleaning and color changes.

Made to hold our 126-A Touch Up Spray Gun. Provides hands-free assistance when pouring resin or gel coats. Can mount to the wall or to a table.

Efficient, accurate, and versatile This portable touch-up gun offers a highly controlled spray pattern for pinpoint accuracy, reducing wasted gel coat and harmful emissions. Its small size, minimal air consumption, and easy clean-up makes it the perfect choice for on-site repairs. This gun comes fitted with a 2.0mm nozzle, which is ideal for any of our gel coats. But don’t use it just for repairs; it’s also great for spraying PVA! Ships complete with 1/4 pint cup, cleaning brush, and 1 mini filter.

Pressure required – 30-80 psiAir consumption – 160-300 liter/minuteCompressor required – 1 HPAir connection - 1/4” n.p.t.Dry weight - .75 lbs

GEL COAT CUP GUN

.6 LITER (20 oz) TOUCH UP SPRAY GUN

PREVAL SPRAYER

CUPS FOR SPRAY GUNS

CUP GUN BRUSH

SPRAY GUN STAND

1/4 PINT (4 oz) TOUCH UP SPRAY GUN





*replacement parts available atwww.fibreglast.com



Description Price Item #Preval Power Unit $7.55 2320-A

Description Price Item #1 Quart Reusable Plastic Tubs $4.25 121-A1 Quart Paper Tubs (sleeve of 25) $17.25 887-A1 Quart Paper Tubs (case of 500) $302.35 887-B

Description Price Item #Preval Glass Reservoir Uncapped $1.05 2321-A

Description Price Item #Preval Glass Reservoir Caps $0.45 2322-A

Description Price Item #Spray Gun Stand $21.55 2249-A

Quantity Discount - Item #: 2320-A10+ $6.95 /Preval Power Unit50+ $6.45 /Preval Power Unit

Quantity Discount - Item #: 2321-A10+ $0.95 /Preval Glass Reservoir Uncapped50+ $0.85 /Preval Glass Reservoir Uncapped

Quantity Discount - Item #: 2322-A10+ $0.40 /Preval Glass Reservoir Caps50+ $0.35 /Preval Glass Reservoir Caps

Quantity Discount - Item #: 2249-A5+ $20.45 /Spray Gun Stand10+ $19.35 /Spray Gun Stand25+ $18.35 /Spray Gun Stand


VACUUM BAGGING

F O A M19

For Floatation and Sculpting #24/25 is a two-part, equal mix, self-rising, 2lb/ cu. ft. density closed-cell foam system. Foaming begins within 45 seconds after the two liquids are mixed and continues for several more minutes. The foam expands

approximately 30 times its liquid volume before curing, and will fill any shape cavity. It does not react with oil or gasoline and it will not absorb water. #24/25 is ideal for floatation applications and provides 60 pounds of floatation per cubic foot of foam. Unlike polyester foams, polyurethane foam is compatible with both polyester and epoxy resins.

2 lb/ft3. Pattern-Making and Moldless Designs. Our 2 lb/ft3 polyisocyanurate foam sheets have the same properties as the mix and pour foam, but come in rigid sheets of varying thickness. They are suitable for most sandwich core applications and are ideal for those which require insulating cores. This foam is easily cut and shaped with a sharp knife and sandpaper. Pattern-making has never been quicker! It can also be glued together to form blocks as thick as necessary for shaping functional moldless-type parts.

Full Scale Building Has Never Been Easier! Polyisocyanurate foam has been a favorite material of pattern builders for years. Now, in 6 foot lengths, and up to 2’ thick, you can cut, carve, sand, and sculpt any shape imaginable without gluing numerous sheets together or pouring your own block. Although this foam can be easily CNC machined, it should not be hot wired. Professional results can be achieved when working by hand. With the variety of tools available on our site, you can saw, carve, plane and smooth out your shape. You will then lay layers of fiberglass and resin to protect and strengthen your shape. Finally, you will spray Duratec® Surfacing Primer and buff to a perfect shine. A perfect plug allows for a perfect mold which makes the high gloss, perfect part you want. These are full six foot blocks available in two different thicknesses - one foot and two foot.

Smaller Blocks for Smaller ProjectsPolyisocyanurate foam has been a favorite material of pattern builders for years. Available in multiple sizes so you can cut, carve, sand, and sculpt any shape imaginable without gluing numerous sheets together or pouring your own block. Although this foam can be easily CNC machined, it should not be hot wired. Professional results can be achieved when working by hand. With the variety of tools available on our site, you can saw, carve, plane and smooth out your shape. You will then lay layers of fiberglass and resin to protect and strengthen your shape. Finally, you will

spray Duratec® Surfacing Primer and buff to a perfect shine. A perfect plug allows for a perfect mold which makes the high gloss, perfect part you want. Smaller block allow for making smaller projects or to practice on smaller pieces before buying a full block. Available in one foot and two foot cubes.

1” Thick, 6 lb/ft3. Pattern-Making and Moldless Designs. This polyisocyanurate foam is a rigid, closed cell foam used in insulation,

core material and carving applications. This foam is easily cut and shaped with a sharp knife and sandpaper. Pattern-making has never been quicker! It can also be glued together to form blocks as thick as necessary for shaping functional moldless-type parts.

2 LB POLYURETHANE MIX & POUR FOAM

2 LB POLYISOCYANURATE FOAM SHEETS

SIX FOOT FOAM BLOCKS

1 FOOT & 2 FOOT FOAM CUBES

6 LB POLYISOCYANURATEFOAM SHEETS

Description Price Item #18 lb. (9 cubic feet) $119.95 24/25-B80 lb. (40 cubic feet) $395.95 24/25-C

Description Price Item #1’ x 4’ x 6’ $599.95 444-A

Description Price Item #2’ x 4’ x 6’ $999.95 445-A

Description Price Item #3/4” x 6ft x 2ft (set of 3) $44.95 440-C1” x 4ft x 2ft (set of 3) $49.95 441-C1.5” x 4ft x 2ft (set of 3) $64.95 442-C2” x 4ft x 2ft (set of 3) $79.95 443-C

Description Price Item #1’ x 1’ x 1’ $99.95 447-A1’ x 1’ x 1’ (2 cubes) $189.95 447-B1’ x 1’ x 1’ (12 cubes) $1,049.95 447-C2’ x 2’ x 2’ $249.95 446-A2’ x 2’ x 2’ (3 cubes) $699.95 446-B2’ x 2’ x 2’ (6 cubes) $1,299.95 446-C2’ x 2’ x 2’ (9 cubes) $1,799.95 446-D

Description Price Item #1” x 4ft x 2ft (set of 4) $174.95 448-D

Description Price Item #1000 lb. (500 cubic feet) $3,100.00 24/25-DRUM

Quantity Discount - Item #: 24/25-C4+ $359.95 /80 lb. (40 cubic feet)10+ $329.95 /80 lb. (40 cubic feet)

Quantity Discount - Item #: 444-A7+ $549.95 /1’ x 4’ x 6’ Block13+ $499.95 /1’ x 4’ x 6’ Block

Quantity Discount - Item #: 444-A4+ $899.95 /2’ x 4’ x 6’ Block10+ $849.95 /2’ x 4’ x 6’ Block


VACUUM BAGGING


S A N D W I C H C O R E20

Lightest Possible ConstructionParts which require minimum weight often employ Nomex® honeycomb sandwich cores. #1562 and #2562 are .210” cut thickness with a 3/16” overexpanded cell. #1562 is 1.8 lb/cu ft. density and #2562 is 3.0 lb/cu ft. Both are quite flexible due to the overexpanded cell structure, making them perfect for use in tight radius curves. All of our resins will bond well to the phenolic coated honeycomb, reducing peel. Nomex® is a registered trademark of E.I. DuPont De Nemours & Co.

Standard Marine Grade CoreEnd Grain Balsa is the most widely used core material. We have it available in 2’ x 4’ sheets of individual small blocks of end grain balsa bonded to a light scrim fabric that holds the blocks together while laminating. Sheets of this core will conform to practically any simple curve and most gradual compound curves. 9.5# density.

Versatile, Formable, and Water ResistantClosed cell vinyl foam is an excellent core material with superior mechanical properties! When used as a structural sandwich core, this foam provides low weight, excellent stiffness as well as high insulation! This foam is used extensively in aircraft and automotive applications and is compatible with all of our resins. Can also be easily thermoformed with a heat gun or oven! 3 Lb. Density Sheets 1/8” Thick x 32” X 48”. 5 Lb. Density Sheets 1/2” Thick x 28” X 48”.

Structural Flow MediaEngineered specifically for vacuum infusion, this core material is grooved, perforated, and scored to create flow channels for resin. A 3.8# Vinyl Foam, Divinymat offers the highest structural properties of any available flow media. Bonded to a light scrim cloth, this core will conform to most simple curves and shapes. 1/8” thick x 32” x 48”.

NOMEX® HONEYCOMB

END GRAIN BALSA

VINYL FOAM

DIVINYMAT

Description Price Item #1/8”, 3 lb density, 32”x48” $29.95 1022-A

Description Price Item #1/2”, 5 lb density, 28”x48” $64.95 500-A

Description Price Item #1/8” Thick, 32” x 48” $29.95 1024-A

Description Price Item #1/4” Thick $24.95 229-A



Description Price Item #1.8 lb - Half Sheet (40” x 48”) $119.95 1562-A1.8 lb - Full Sheet (40” x 100”) $199.95 1562-B1.8 lb - Case (10 full sheets) $1,799.95 1562-C3 lb - Half Sheet (40” x 48”) $134.95 2562-A3 lb - Full Sheet (40” x 100”) $219.95 2562-B3 lb - Case (10 full sheets) $1,999.95 2562-C

Quantity Discount - Item #: 1022-A5+ $27.9510+ $25.9550+ $23.95

Quantity Discount - Item #: 500-A6+ $59.9511+ $54.95






VACUUM BAGGING

V A C U U M B A G G I N G M A T E R I A L S21

60” Wide, Stretches to compress every area of the mold This high elongation bagging film is rated for temperatures up to 250°F and can stretch to 500% of its original length. Unlike traditional bagging film, Stretchlon can be fitted over complex shapes without pleats or rabbit ears as it stretches to conform to nearly every shape. This material can conform to autoclave pressures. Compatible with epoxy resin only.Stretchlon® is a registered trademark of Airtech International.

60” Wide, High temperature elastic film for any mold. This bagging film is rated for temperatures up to 400°F and can stretch to 450% of its original length. This film is compatible with our polyester, vinyl ester and epoxy resins. Like the Stretchlon® 200, this material can be fitted over nearly any shape without rabbit ears or pleats and can handle autoclave pressures as well as higher temperatures. Stretchlon® is a registered trademark of Airtech International.

Bag Building and Higher Temperatures This film resists temperatures up to 375 degrees F, is .002” thick, 60” wide, is puncture resistant, and very strong. Do not count on any bagging film stretching to meet the contours of the mold. You must crease pleats to ensure full depth coverage within the mold.

Leak Free and Extra TackyThis tape will seal the bag to aluminum, steel, fiberglass, nickel, and graphite tool surfaces while supplying more aggressive tackiness than #581. Extra tackiness makes this tape less likely to shift or spring leaks under vacuum but it can be more difficult to reposition if initial placement is not precise. Maximum service temperature is 400 degrees F. 1/2” wide, 1/8” thick, and 25’ per roll.

Leak FreeThis tape will seal the bag to aluminum, steel, fiberglass, nickel, and graphite tool surfaces yet strips easily after cure. Use to plug leaks and tears in the bag that can develop during cure. Maximum service temperature is 400 degrees F. 1/2” wide, 1/8” thick, and 25’ per roll.

Releases Cleanly This multipurpose polyester tape is used within the bag to hold other materials in place before the vacuum is pulled. It can also be used as a release film by applying it to mandrels and molds before lay-up. Highly recommended for temperatures over 400 degrees F. 72 yards per roll, 1” wide.

Room Temperatures and Small Molds For room temperature and exotherms up to 180 degrees F. 24” wide and .0025” thick, this low density polyethelene film is a tube and only two sides must be sealed to create an envelope bag.

STRETCHLON® 200 BAGGING FILM

STRETCHLON® 800 BAGGING FILM

NYLON BAGGING FILM

YELLOW SEALANT TAPE

GRAY SEALANT TAPE

FLASH TAPEPOLYETHELENE BAGGING FILM









Description Price Item #Single Roll $7.95 580-ACase (40 rolls) $249.95 580-B

Description Price Item #Single Roll $7.95 581-ACase (40 rolls) $259.95 581-B

Description Price Item #Flash Tape $29.95 584-A

Quantity Discount - Item #: 580-B9+ $209.95

Quantity Discount - Item #: 581-B9+ $199.95



VACUUM BAGGING


V A C U U M B A G G I N G M A T E R I A L S22

Maximum Air and Resin TransferThis fabric provides an easy release and a textured surface for secondary bonding or painting. Both air and resin will transfer through every pore, ensuring a void-free laminate. Use strips anywhere secondary bonding is to occur. Service temperature is 350 degrees F, 60” wide, and .004” thick. Not recommended for phenolic systems

Moderate Resin TransferThis polyester peel ply is scoured, heat set, and leaves a fine surface for priming or secondary bonding. It can be used at service temperatures of 350 degrees F and is resistant to phenolic resin system degradation. 60” Wide.

Retain Resin for High Gloss This high gloss elongation release film can be used on wet or prepreg moldings up to 200 degrees F. It is perforated with holes of .045” diameter on 1/2” centers to allow for passage of air and excess resin. This film will hold more resin than the peel ply releases. Not recommended for phenolic systems. 60” wide.

Easy to Drape and Binder FreeThis high fill non-woven polyester will easily drape to conform closely to the contours of your part. It does not contain any binders which could close off air flow within the mold, and it will readily wick up excess resin. .003” Thick, 4 oz/sq yd, 60” wide

NYLON RELEASE PEEL PLY

POLYESTER RELEASE PEEL PLY

LOW TEMPERATURE RELEASE FILMBREATHER AND BLEEDER




Pre-Cut Length Price/Roll Item #1 yd package $7.95 579-A3 yd roll $16.95 579-B5 yd roll $24.95 579-CSwatch (4”x 6”) $1.95 579-SWATCH





VACUUM BAGGING MATERIALS SAMPLE PACKThis convenient Sample Pack contains a 4” x 6” swatch of all of our vacuum bagging materials. It is ideal for determining which material you would like to try for your application. Plus, each Sample pack includes a coupon for $25 off your next order of $100 or more when purchased within 60 days!


The Art Department LLCLong Branch, NJ


VACUUM BAGGING

V A C U U M I N F U S I O N23

A Place to StartWe created our #590-A Vacuum Infusion Trial Kit as a means of familiarizing someone with the materials that are unique to vacuum infusion. We strongly suggest significant experience with both vacuum bagging and room temperature molding before tackling resin infusion. This kit contains enough material to build 3 infusion trial projects up to 24” x 13” each. After completing these 3 “practice” laminates you will be familiar with EnkaFusion Nylon Matting, Lantor Soric, EnkaFusion Filter Jacket and Divinymat Sandwich Core. You will be able to judge the differences in resin travel and conformability as suits your future infusion applications. Additionally, you will be able to install your vacuum and resin lines and get some experience controlling your resin bucket and resin flow.

In order to use the kit, you will need your own vacuum pump, bagging materials and vacuum tubing to attach to the bag. Also, you will need to supply your own resin and reinforcement. Last, you will need a mold that will require a laminate no larger than 24” x 13” that also has a relatively large flange.

This kit will supply everything you need for:

One laminate using EnkaFusion Nylon Matting as a Flow MediaOne laminate using Lantor Soric® as a Flow MediaOne laminate using Divinymat® Sandwich Core as a Flow Media

Includes:

#505-A Resin Bucket 1 Gallon (x3)#512-B Resin Line Holder (x3)#893 Vacuum Tubing 5’pieces (x3)#1601 Zip Strips (x6)#1400 Filter Jacket 5” (x3)#582 Peel Ply 5’x5” pieces (x3)#1024 DIVINYMAT® 24”x16”#1401 Nylon Matting 24”x13”#1605-A Flow Regulator (x2)#1606-A Spring Clamp#906-A T-Fittings (x6)#1400 Filter Jacket 18” (x3)#1403 Spiral Tubing 5’ pieces (x3)#582 Peel Ply 20”x5” pieces (x3)#1409 Lantor Soric® 24”x16.37”Instruction Sheet

If you can vacuum bag, you can infuse resin. The objective of this kit is to help you make informed decisions about choosing your flow media, placing and using spiral tubing and designing successful experiments for your own projects in the future. After completing these trial projects, you will be confident in planning your future flow media and resin line set up. You will be familiar with all of the terms used in this brochure and hopefully, will be able to reduce the learning curve and costs associated with the trial and error of successful vacuum infusion!

VACUUM INFUSION TRIAL KIT

*SEE DIVINYMAT ON PAGE 20.

Resin feed lines made easyWith a three-dimensional “V” shaped core contained within a polyester “sock,” this creates an open flow channel for resin to race through during infusion. Used as a resin feed line, the sock will create even flow rates outward across its entire length. 4” Wide.

3mm, 50” Wide. The most conformable of the flow media, this product will aid infusion and quickly build thickness with up to 35% less resin retention than all-glass laminates. Unique design of hexagonal flow channels on a carrier sheet creates a steady, even resin front resulting in maximum conformability and surface finish. Compatible with all of our resins and reinforcements.

Fastest infusion timesConsisting of randomly oriented, entangled filaments, this flow media provides maximum resin flow while limiting resin retention. Used on the surface or as an interlaminar media, Nylon Matting provides the fastest infusion times. 39” Wide.

For vacuum or infusion lines A vacuum infusion standard, this tubing is ideally suited for in-bag vacuum line extenders or resin feed lines. 1/2” ID is compatible with all of our hose fittings.

Protect your pumpDon’t let vacuum infusion destroy your pump. This 2 ½ gallon stainless steel vacuum sealed tank is used between the mold and the vacuum pump for capturing excess resin that enters the vacuum line before it can damage your equipment. More than 1 can be used in-line for large jobs! Simply apply mold release prior to lay-up and then pop out the cured resin for many reuses. Comes complete, including vacuum gauge and instruction manual.2.5 gallon capacity

ENKAFUSION FILTER JACKET

LANTOR SORIC® XF

ENKAFUSION NYLON MATTING

SPIRAL TUBING

RESIN TRAP

Description Price Item #5 yd roll $9.95 1400-A10 yd roll $14.95 1400-BCase (10 yd roll x 4) $49.95 1400-C

Description Price Item #1 yd roll $9.95 1401-A3 yd roll $26.95 1401-B5 yd roll $39.95 1401-C10 yd roll $69.95 1401-D20 yd roll $129.95 1401-EFull Roll, 84 yds (no core) $399.95 1401-F

Description Price Item #10 ft spool $19.95 1403-A50 ft spool $64.95 1403-BCarton (50 ft spool x 3) $189.95 1403-CCase (50 ft spool x 10) $549.95 1403-D


Pre-Cut Length Price/Roll Item #1 yd roll $24.95 1409-A3 yd roll $69.95 1409-B5 yd roll $104.95 1409-CCustom Cut - min. qty of 10 yds. Item #: 140910+ yds $18.95 /yard25+ yds $18.45 /yard55+ yds $17.95 /yard

Price Item #$299.95 1500-A



VACUUM BAGGING


V A C U U M F I T T I N G S24

All You Need is an Air Source!Our Vacuum Bagging Starter Kit contains everything you need to set up a complete vacuum bagging station. Since all of our fittings, tubing and components fit together perfectly, you can add any additional parts you want. But it is not necessary to buy anything else to get started! You need some type of compressor to supply air. You will also need to have prepared your part and selected all of your vacuum bagging films and materials.

This kit contains:(1) #2215-A Small Regulator/Filter to filter air from your source to the vacuum generator and also allows you to dial in the correct air pressure.(1) #2229-A High Efficiency Vacuum Generator pulls a lot of vacuum with a small amount of air!(2) #2217-A air Hose Assemblies, 5 Foot Lengths to connect from your air source to the regulator and from the regulator to the Vacuum Generator.(1) #2218 Vacuum Gauge with T-Fitting allows you to easily monitor vacuum anywhere in your tubing line – put it where you want it! You can measure closer to the pump or right at the part.(10) Feet of #893 Vacuum Tubing(4) #789-A Hose Clamps(1) #891-A Vacuum Coupling

Keep Moisture Out and Control Your Pressure. This compact Regulator/Filter is a great size for a small workshop or garage. This unit is designed to filter your air to keep debris and liquids from getting inside your equipment. Additionally, it permits you to dial in and maintain the correct air pressure. Install the Regulator/Filter in your line close to your air source to filter out any moisture or debris. Includes poly cup for debris containment which can then be thrown away. This unit can be used on our #2229-A or #1148-A Vacuum Generators, any of our Gel Coat Spray Guns and our #1171-A Chopper Gun. Max PSI 150. Connection to our #1171 Chopper Gun and #120 Gel Coat Cup Gun requires a #2222 Male Nipple. Connection to our #123 or #126 Gel Coat Touch Up Spray Guns require a #2223-A Female Nipple.

Industrial Environment Moisture Containment and Pressure Control. This industrial style Regulator/Filter has a larger filter than our #2215-A and includes a metal shield to protect the polycarbonate cup. A thumb screw at the bottom allows for easy draining of any liquids that accumulate in the cup. . Install this Regulator/Filter in your line close to your air source to filter out any moisture or debris as well as to dial in and maintain your air pressure. This unit can be used on our #2229-A or #1148-A Vacuum Generators, any of our Gel Coat Spray Guns and our #1171-A Chopper Gun. Max PSI 150. Connection to our #1171 Chopper Gun, #120 or #836 Gel Coat Spray Guns require a #2222 Male Nipple. Connection to our #123 or #126 Gel Coat Touch Up Guns require a #2223-A Female Nipple.

This Quick Disconnect and the Male and Female Nipples can be used to turn setup and tear downs into a quick and convenient task. Setup of vacuum applications is significantly easier because all vacuum hose can be added at the last minute allowing more focus on the laminate itself. Some vacuum bagging applications will also benefit from the #2220 Brass Barb Fitting to quickly thread vacuum components turning your entire vacuum line into an easy quick disconnect operations. For spray and chopper applications, our air hoses are already supplied with a quick disconnect fitting but require a nipple to attach to the gun. Connection to our #1171 Chopper Gun, #120 or #836 Gel Coat Spray Guns require a #2222-A Male Nipple. Connection to our #123 or #126 Gel Coat Touch Up Guns require a #2223-A Female Nipple

When conventional air line is used as the vacuum tubing, this connector will fit the threaded brass hose end effectively coupling the pump and the bag. Also, to install a gauge inside the bag, a support connector is required. This connector supports and mounts the gauge in the bag to permit pressure within the bag to register. Fitting permits male to male connections.

This 1/2” ID connector is all that is required to complete a basic installation. Place the connector through the bag, attach tubing, and you’re ready to begin!

1/2” tubing selected to be inexpensive yet resistant to collapse throughout the vacuum cycle. (Price per ft.)

Fitted to Easily Connect. Our industrial quality air hoses have been prefitted with ¼” quick disconnect fittings to easily plug into your air source, our #2229-A or #1148-A Vacuum Generators, our #2215-A or #2216- A Regulator/Filters, any of our Gel Coat Spray Guns and our #171-A Chopper Gun. However, additional fittings are required for the following: Connection to our #1171 Chopper Gun, #120 or #836 Gel Coat Spray Guns require a #2222-A Male Nipple. Connection to our #123 or #126 Gel Coat Touch Up Guns require a #2223-A Female Nipple. Simply snap in the hose and you will be ready to go. This high quality hose is suitable for daily use in a general industrial environment and will not degrade under moderate contact with oils or resins.

1/2” OD permits multiple bags to be installed.

Serrated arms permit a tight fit in multiple bag applications.

VACUUM BAGGING STARTER KITSMALL REGULATOR/FILTER

LARGE REGULATOR/FILTER

qUICK DISCONNECT & NIPPLES

THRU-BAG VACUUM CONNECTOR

VACUUM CONNECTOR

VACUUM TUBING

AIR HOSE ASSEMBLIES

T-FITTING

EqUAL ANGLE Y CONNECTOR

Price Item #$379.95 2227-A

Price Item #$129.95 2215-A

Price Item #$149.95 2216-A

Description Price Item #Screw-On Quick Disconnect $19.95 2219-A

Female Quickchange Steel Nipple $3.95 2223-A

Male Quickchange Steel Nipple $3.45 2222-A

Description Price Item #Vacuum Connector $4.95 891-AVacuum Connector (dozen) $49.95 891-B

Description Price Item #T-Fitting $2.95 906-AT-Fitting (dozen) $29.95 906-B

Description Price Item #Equal Angle Y Connector $7.95 907-AEqual Angle Y Connector (dozen) $79.95 907-B


Description Price Item #Vacuum Tubing /foot $1.45 893

Description Price Item #5 ft $29.95 2217-A10 ft $39.95 2217-B25 ft $69.95 2217-C50 ft $99.95 2217-D

Quantity Discount - Item #: 89351+ feet $1.25 /foot


VACUUM BAGGING

V A C U U M F I T T I N G S25

2” diameter face with glass lens cover and easy-to-read markings allows measurement and thus permits control of vacuum pressure. Can be installed with either a #898-A, #902-A, or a #910-A connector.

Keep the resin line in the bucketThis clamp is used to keep the resin line in place by clamping the stick (with small sticks) or by clamping the zip strip to the bucket.

Measure flow times to control quality.Monitoring resin flow rates over time is an important part of perfecting an infusion project. Just start the clock when resin is introduced to gather valuable data. This inexpensive stop watch is perfect for the job.

Permits installation of a vacuum gauge at the pump, but can introduce vacuum relief if reduced pressure is desired.

This fitting is used to connect the #2224-A Brass Two-way Shutoff Valve to the #2218-A Vacuum Gauge with T-Fitting, #898-A T-Attachment Assembly, #902-A Bleed-off Valve Assembly or an combination of male to male connections.

#2225-A Plumber’s Tape should be used for all brass fittings and threads to ensure a leak proof joint.

Secure your tubing connections every time withthese hose clamps. Continuous band construction will clamp tightly without cutting or

digging into the tubing. Fits all of our vacuum tubing, spiral tubing and fittings.

The easiest way to install a vacuum gauge. Permits installation at pump for readout of vacuum pressure.

This assembly allows you to easily monitor vacuum anywhere in your tubing line – put it where you want it! You can measure closer to the pump or right at the part.

A simple way to reduce vacuum pressure by limiting flow

through the line. This valve is installed to permit vacuum relief or to seal off a vacuum bag. The new brass two-way shutoff valve is an industrial style valve that will stand up to harsh shop environments. The valve can be used in the line or can be attached to the vacuum gauge with t-fitting, t-attachment assembly, or bleed-off valve assembly.

½” OD Barb Fittings can be threaded into the #891-A Through Vacuum Connector

or other vacuum bagging components to reduce the use of hose clamps and/or permit the installation of Quick Disconnects. We supply the #901-A Plastic 1/2” OD barb fitting with all pumps and assemblies, but they might need periodic replacement. Additionally, the #2220-A Brass Barb Fitting is designed to handle harsh environments and should be used in production style applications.

VACUUM GAUGE

SPRING CLAMP

STOP WATCH

BLEEDOFF VALVE ASSEMBLY

MALE TO MALE FITTING

PLUMBERS TAPE

HOSE CLAMPS

T-ATTACHMENT ASSEMBLY

VACUUM GAUGE WITH T-FITTING

BRASS/PLASTIC TWO-WAY SHUTOFF VALVES

BRASS/PLASTIC BARB FITTINGS






Description Price Item #Brass Barb Fitting $4.95 2220-ABrass Barb Fitting (dozen) $49.95 2220-BPlastic Barb Fitting $1.05 901-APlastic Barb Fitting (dozen) $9.95 901-B

Description Price Item #Brass Ball Valve $19.95 2224-ATwo Way Shutoff Valve $16.95 909-A

Description Price Item #Plumbers Tape $3.95 2225-A

Description Price Item #Hose Clamps $1.55 789-A

Description Price Item #Spring Clamp $3.95 1606-A





Dave KenyonBlack Rock, NV



VACUUM BAGGING


P U M P S & T O O L S26

Simple and Immediate Use. A Great Starter Pump! Rated for continuous operation, this oilless pump is wired for immediate use in a standard 110 outlet. Supplied with a barb fitting which ensures secure coupling to #893 vacuum tubing. The only assembly required is the attachment of feet which are also supplied with the pump. Suitable for parts up to 30-40 sq ft. 1/16 HP, 24” Hg, .5 CFM Diaphragm Pump comes with Unlimited One Year Warranty.

For Big Jobs and Tough Environments. This industrial single-phase pump is ideal for applications where the discharge must be totally free of oil. This rotary vane vacuum pump requires very low maintenance, has long vane life and low noise levels. It is designed to operate on a continuous basis throughout a pressure range of atmospheric pressure to 25.5” Hg. .56 HP, 25.5” Hg, 5.6 CFM Rotary Vane. Pump comes with unlimited One Year Warranty.

The 2229-A is capable of pulling 26” Hg with only 0.95 CFM. The 1148-A will create 27” of Hg vacuum/pressure when coupled in-line to an air compressor capable of producing 2.2 CFM.

The easiest way to find leaksThis time-saving device amplifies ultrasonic frequencies while filtering out background noise, making it ideal for pinpointing leaks during vacuum bagging or infusion. Headphones provide easy listening, while LED display meter indicates leak strength. Includes Ultrasonic Leak Detector, tubular extension adapter, tubular extension, parabola, headphones, and carrying case. Dimensions: 1” x 2.5” x 7.3,” Weight: 4.5 oz or 6.3 oz (with battery,) Requires 9V (included), Frequency response: 35kHz to 45kHz +6db

Economic approach to leak detectionA low cost alternative to assisting leak detection. A stethoscope can help detect small leaks in a vacuum seal without expensive filtering devices.

Know When Resin Has Begun and Finished Curing. This easy to use device reads surface temperatures from 0-575 degrees F to within 3 degrees. Simply point and pull the trigger for instant visual readings. Ideal for identifying when resin is curing and maximum exotherm is achieved. Aim at resin in your bucket or in your laminate and know exactly when it’s setting up. Model includes laser guide for pinpoint accuracy. 9V battery included.

Snip quickly and cleanlyThe easiest way to cut tubing, these handy hose cutters do the job quickly and keep you moving. Use with any of our tubing for clean cuts every time, even at awkward angles.

Easy on and easy offClamping off tubing to begin and end resin flow is a critical step in any infusion project, and these devices make it easy. Crease the tubing to block off flow and then lock into place using this regulator.

1/16 HP STARTER VACUUM PUMP

INDUSTRIAL .56 HPVACUUM PUMP

VACUUM GENERATORS

ULTRASONIC LEAK DETECTOR

STETHOSCOPE

THERMAL GUN

HOSE CUTTERS

FLOW REGULATOR

Description Price Item #Hose Cutters $29.95 1501-A

Description Price Item #Flow Regulator $2.95 1605-A



Price Item #$449.95 888-APrice Item #

$399.95 1503-A



Price Item #$1,219.95 2228-A

Price Item #$109.95 2229-A

Price Item #$109.95 1148-A


WIND ENERGY

W I N D E N E R G Y P R O D U C T S27

This Saertex biaxial cloth is a high strength stitched fiberglass +/-45°. This no-crimp fabric is ideal for wet layup and infusion processes which require fast wet out and strength control. This easy handling fabric can be used with polyester, vinyl ester or epoxy resin systems.

This Saertex unidirectional cloth is a high strength stitched fiberglass 0/90, 50” wide. This no-crimp fabric is ideal for wet layup and infusion processes which require fast wet out and strength control. This easy-handling fabric can be used with polyester, vinyl ester or epoxy resin systems.

300 ml ctg (10.1 oz)One Component , fast curing polyurethane based elastomeric adhesive/sealant. Moisture cured, non-sag system. Permanently elastic bond to fasten materials which have dissimilar coefficients of expansion. Applications: Exposed/concealed lap seams, rivet seams, roof rails, expansion/control joints, pre-cast concrete panel joints and tilt up panel joints. Substrates: Aluminum, steel, wood, FRP, SMC, RIM, prepainted metals, Zincalume, Zincgrip and aluminized steel - many without primers. Advantages: Does not attack metal coatings, rapid cure. Overpaint once fully cured, with water, oil and rubber based coatings. Provides shock resistance, vibration damping. Weather resistant, resistant to road salts. NSF/USDA approved for incidental food contact. Resistant to cuts and tears. Key Properties: Tack free time 50 - 90 minutes, Elongation at break 600%, Tensile Strength 225 psi, +/- 12.5% expansion/contraction.

10.5 oz ctg (300 g)High Strength Elastic adhesive, one component, moisture cured polyurethane adhesive with extremely high thixotropy and high strength.Applications: Particularly suited for bonding of metal or wood, trim, molding, styling elements, structural bonding of large parts including sheet metal and composites. including large panels. Bonding of FRP roofs, sandwich panels and walls. Used extensively on trucks, trailers and equipment. Sealing applications especially for large joints. Replaces rivets and mechanical fasteners. Substrates: Wide range of substrates including wood, primed metal, glass, composites. Advantages: Bonds and seals, short tack free and curing time, initial load bearing capacity, sandable and overpaintable for most coatings once fully cured, shock and impact resistant, offers vibration and sound damping prop-erties, increases torsional stifness of final assembly. Key Properties: Tack free time 30-45 minutes, Elongation at break 300%, Tensile strength 550-650 psi.

600 ml Unipac (20.3 oz)Sikaflex® -521UV incorporations the latest technology from Sika®, Hybrid. Sika® Hybrid Technology combines the tried and true experience in polyurethane sealants with silanes, which give great adhesion with little or no surface preparation. Sikaflex® -521UV is UV resistant, so it retains its color perfectly after years in the sun. White stays white, black does not chalk or streak.

SAERTEX® FABRICS

SAERTEX 835 G/M2 (25 Oz/YD2) STITCHED BIAXIAL (+/-45), 50”



SAERTEX 955 G/M2 (28 Oz/YD2) STITCHED UNIDIRECTIONAL, 50”

SIKAFLEX® - 221: ONE-COMPONENT ADHESIVE/SEALANTWHITE & GRAY

SIKAFLEX® - 252: ONE-COMPONENT, ELASTIC ADHESIVE - WHITE

SIKAFLEX® - 521UV - GRAY









Description Price Item #White - Each $6.95 2922-AWhite - Case of 24 $149.95 2922-B

Description Price Item #Each $12.95 2924-ACase of 24 $279.95 2924-B


Description Price Item #Gray - Each $6.95 2923-AGray - Case of 24 $149.95 2923-B


WIND ENERGY


W I N D E N E R G Y P R O D U C T S28

250 ml Bottle (8.5 oz)Transparent, Special adhesion promoting solution for pretreatment of bonding surfaces prior to bonding or sealing with Sikaflex® products. Applications: Surface Cleaner and preparation agent. Metals, many plastics, many types of paints and lacquer based finishes. Advantages: One component, fast drying, improves adhesion and yields a more weather resistant seal. Key Properties: See Substrates, Flash Point 57° F, Application Temperature 40° to 110° F, Drying time 10 minutes @73° F/50% R.H. Shelf Life: 12 Months (Unopen container)

No measuring required. This device can quickly and easily dispense #2906 Bergolin 400 ml Putty Cartridges. Insert the 400 ml cartridge kit into the dispenser, remove ring and plug, and carefully pull the handle until both components dispense evenly.

Compact and easy to carry, this dispenser is great for repairs using #2905 Bergolin 50 ml Putty Cartridges. Simply insert the 50 ml cartridge kit into the dispenser, remove ring and plug, and carefully pull the handle until both components dispense evenly.

RAL COLOR - 7035This pigmented Putty is a proven and tested, high-performance coating system for repairing rotor blades. Achieve fast, safe and superior results by using this material on repairs that require elasticity and maximum durability. The two-component cartridge can be carried anywhere and no measurement is required when dispensing. Advantages: Easily dispensed and mixed. Extremely portable. Fast curing. Solvent free, Excellent exterior durability Elasticity for temperature fluctuations and substrate movement. Properties: Dispenses product at a ratio of 2:1 with hardener. Fast setting within 5 minutes. Tack free after 60 minutes. Mixing: Place cartridge kit in appropriate dispenser, remove ring and plug from cartridge, dispense amount required, and mix and apply. Hold the cartridge in an upward angle and pull handle until both products dispense evenly. Dispense the amount required into a container. Mix well until uniform. Dispense and mix only enough product that can be processed within 5 minutes. Apply using a hand trowel or spreader until uniform and even. This putty can be continuously coated once the mixed product begins to set. There are no solvents to flash or remove prior to recoat or to overlap. The reacted filler should be sanded prior to recoat after 24 hours of curing. Does not require an additional topcoat. (A topcoat can be used, if required after sanding the putty)

Avon Extra Thrust 20 oz.Product Type: Single Component Application: Sausage/Cartridge/Bulk Capacity: 10 oz. Cartridge, 10 oz. Sausage, 20 oz. Sausage, Bulk Mix Ratio: non-applicable

Features:20 oz. / 10 oz. Sausage, 10.3 oz. Cartridge and Bulk ApplicationPre-Configured for Sausage ApplicationPlunger Included for Cartridge and Bulk ApplicationsMechanical Advantage 18:1 All Component Replaceable PartsIncludes Three Yellow Cone Nozzles, Ladder Hook and Spanner Wrench

Trent - 20 oz.Product Type: Single Component Application: Sausage Capacity: 20 oz. Sausage Mix Ratio: non-applicable

Features:Floating Plunger Action with Secure CordDrawn Aluminum BarrelTrue Adjustable Air Regulator - 100 PSI MaximumInstant Dump ValveSilencerQuick Release End CapAll Component Replaceable PartsRotating Air Hose Connector and One Orange Cone Nozzle Included

TyneProduct Type: Single ComponentApplication: CartridgeCapacity: 10 oz. CartridgeMix Ratio: non-applicable

Features:Air Action on Cartridge PlungerDrawn Aluminum BarrelTrue Adjustable Air Regulator - 100 PSI MaximumInstant Dump ValveSilencerQuick Release End CapAll Component Replaceable Parts Rotating Air Hose Connector Included

Replacement Nozzle for the Manual Cartridge or Unipac Dispenser (SKU #2927)

SIKA® - CLEANER 226

BERGOLIN DUAL CARTRIDGE CAULKING GUN ADAPTER 400 ML

BERGOLIN DUAL CARTRIDGE CAULKING GUN ADAPTER, 50 ML

BERGOLIN PUTTY CARTRIDGE, 400 ML

BERGOLIN PUTTY CARTRIDGES400 ML & 50 ML

BERGOLIN PUTTY CARTRIDGE, 50 ML

MANUAL CARTRIDGE OR UNIPAC DISPENSER

PNEUMATIC UNIPACDISPENSER

PNEUMATIC CARTRIDGE DISPENSER

REPLACEMENT NOzzLE FOR 2927


Description Price Item #Each $59.95 2906-ACase (12 Cartridges) $649.95 2906-B

Description Price Item #Each $34.95 2905-ACase (50 Cartridges) $1,595.95 2905-B


Price Item #$161.95 2917-A


Price Item #$215.95 2928-A

Price Item #$215.95 2929-A


BS Rotor TechnicAnaheim, CA



M O L D P O L I S H29

Don’t Forget This Important Step! Step 1 - Fast Cut After Sandpaper Step 1 is a water-based polishing compound which begins work where sandpaper stops. 600-1000 grit scratches will rapidly be removed with this fast

cutting compound. Step 1 Mold Polish also removes styrene and wax buildup from existing molds. Use this economical compound and achieve great results with only half the normal amount of compound material. Water-base material is safe for use in the paint shop environment. Suggested buffing speed: 2500 rpm min., and a # 1104-A buffing pad is recommended for best results. Step 2 - Removes Finer Scratches Step 2 Mold Polish will remove finer scratches and polish FRP parts, molds, and even painted surfaces to an exceptionally glossy surface. This economical polish uses half the material to achieve the results from typical compounds. Water-based material is safe for use in a paint shop environment. Suggested buffing speed: 2500 rpm min., and a 1104-A lambs wool buffing pad is recommended for best results.

Ideal For Our Polish Compounds This 50% synthetic and 50% lambs wool pad is the recommended buffing pad for our polishing compounds. Do not attempt to use these mold polishing compounds with a foam pad! The #1104-A buffing pad is a great tool for buffing

the #1102 Step One Mold Polish, the #1103 Step 2 Mold Polish, and the #113 Meguire’s Machine Glaze. This pad will withstand the 2500 rpm minimum buffing speed required for use with all three compounds. Remember, you MUST change pads when changing compounds or the small dust particles trapped in the pad from the previous grade will continue to cut the surface!

Plenty of Uses KLEEN KLAY® is a non-drying clay having many applications in most phases of fiberglass molding including temporary fillets, construction of mold parting lines and quick repairs to molds. The oil base of this clay allows PVA separator to be applied to it and also provides a good measure of adhesion to waxed surfaces. KLEEN KLAY is a registered trademark of Art Chemical Products.

Don’t Forget This Important Step! Wet sand the surface of new molds to perfection before polishing. This significantly increases the quality and longevity of any mold, and all parts made in it! Using consecutively finer grades of sandpaper from

240-600, any orange peel, texture from PVA, or other imperfections in the mold surface can easily be removed. Also, use for sanding the plug before molding, and leveling of external gel coat repairs. Each combination package includes 240, 320, 400, 500, 600 grit.

A Hard Rubber Sanding Block is ideal for removing materials from only high areas until they blend well with the overall surface. This versatile block can be used wet or dry with any grade of paper during rough shaping of

the plug or finish sanding the clear gelcoat on a cosmetic repair.

A 3M™ Wetordry Sponge Pads are ideal for sanding the entire work surface once it’s fair and level. Simply wrap the sandpaper around the pad.

Applies even pressure eliminating finger waves in the final finish.

Smoothing and Shaping. These sanding sponges are great for smoothing tool marks out. There are three grits to choose from: 100, 150, and 220.

Step three in the mold polishing sequence This compound conditions the mold surface prior to waxing. #113 eliminates any final swirl marks which may be present at this stage. Additionally, this formula actually ‘feeds’ the surface with a wax-like petroleum product which deepens the effect of later coats of release wax. This product contains no silicones, making it safe for the paint shop environment. Suggested buffing speed: 2500 rpm min., and a #1104-A lambs

wool polishing pad is recommended for best results.

STEP 1 MOLD POLISH AND STEP 2 MOLD POLISH

BUFFING PADS

MODELING CLAY

3M™ WETORDRY™ SANDPAPER

HARD RUBBER SANDING BLOCK

3M™ WETORDRY™ SPONGE PAD

SANDING SPONGES

MEGUIAR’S MACHINE GLAzE

Description Price Item #Step 1 Mold Polish (1 lb can) $16.15 1102-AStep 1 Mold Polish (5 lb can) $53.95 1102-BStep 2 Mold Polish (1 lb can) $16.15 1103-AStep 2 Mold Polish (5 lb can) $53.95 1103-B

Description Price Item #100 Grit $1.95 2138-A100 Grit (dozen) $19.95 2138-B150 Grit $1.95 2136-A150 Grit (dozen) $19.95 2136-B220 Grit $1.95 2137-A220 Grit (dozen) $19.95 2137-B

Description Price Item #Package (1 lb) $4.25 104-ADozen (1 lb packages) $37.75 104-BCase (36 lbs) $107.95 104-C

Description Price Item #1 Sheet of Each (5 total) $9.95 968-A5 Sheets of Each (25 total) $44.95 969-A10 Sheets of Each (50 total) $79.95 970-A

Description Price Item #Buffing Pads $21.55 1104-A Description Price Item #

Sanding Block $5.95 961-A

Description Price Item #Sponge Pad $9.95 962-A




Price Item #$21.55 113-F

Brock TechnologiesTucson, AZ




M O L D R E L E A S E30

Inexpensive and Effective Barrier PVA (Polyvinyl Alcohol) should be used with #1016 Wax to aid in the release of parts from a mold. It should be applied in three thin mist coats over nonporous, waxed mold surfaces. After the final wax coat has dried, begin by spraying a light tack coat of PVA. Typically, within 5 minutes the final heavier coats can be added. The PVA dries to form a smooth, glassy film. After part release, the residual film can be removed with water. We recommend using our 123-A or 126-A Touch Up Spray Guns for larger molds, but for smaller molds, use our 2251 Preval Sprayer . PVA can also be sprayed over any polyester repair to provide an airless tack-free cure.

Reusable, Reliable and Necessary for Most Mold Releasing. Plastic release wedges are used to aid in removing medium to large parts from a mold. The wedges are inserted around the perimeter of the mold, between the mold and the part, and then gently driven in until the piece pops out. The theory behind using a wedge is that concentrated pressure is applied to that portion of the part not yet released. To make this scheme work it is necessary to use a sufficient number of wedges and to progress around the mold tapping each wedge in turn. One wedge will not help. The soft polyethylene construction will not scratch the mold or the part.

Use Air Pressure to Force Out Stubborn Parts. Designed for demolding large or hard-to-separate parts. Standard wedges can only reach a few inches into the mold, but air pressure will travel all the way to the sticking point to provide pressure where it is needed most. This heavy duty poly-pro wedge is designed for extra long life.

Effortless One-Step Release Agent. Fibre Glast’s first one step release agent is compatible with all our resins, saves valuable time, and uses little material. Mold preparation and cleaning times are so quick you’ll feel guilty! We have tested this product during both part and mold fabrication with excellent results. Water-based FibRelease® contains no harmful solvents, chemicals, or silicones so it is worker and environmentally safe. It has been developed as an easily applied, non-VOC, non-silicone, non-transferable material with effortless release characteristics. It is compatible with the paintshop environment, and will not easily pre-release. Application is easy! We recommend starting with a properly polished mold surface,and rebuffing as necessary to maintain the Class “A” finish. Simply mist or wipe FibRelease® onto the mold surface and allow it to dry to its film state. 5 minutes is usually sufficient. One application will provide multiple releases, but the process is so quick we recommend using it every time for added insurance. The maximum service temperature is 550° F.

Simple and ReliablePaste Wax is a non-silicone green wax specially formulated to produce a tough, durable, high gloss surface. Excellent release characteristics are achieved when used with # 13 PVA. We recommend that new molds are coated with four layers before use. Apply two coats of wax, buff off the excess, and allow to stand for an hour before applying the last two coats. The wait is to give solvents extra time to evaporate so a tougher wax barrier develops.

Excellent System for Seasoned Molds Meguiar’s Mirror Glaze products comprise a complete production mold system based upon proper mold preparation and a paste wax. The advantages of this system are many; it yields parts with a very high gloss, involves no time consuming sprays and , with proper care, provides trouble-free releases. This system is compatible with PVA for added release insurance.

Quick & Sturdy Fastening System . As shown in “A Step by Step Guide to Molding Fiberglass”, this unique clipping system quickly joins multiple piece molds during final assembly. Using 1/8” holes, the clips hold the mold tightly to prevent slipping and misalignment. Use the Fastening Clip Plier to quickly attach and remove the special clamps.

PVA RELEASE FILM

RELEASE WEDGES

AIR INJECTED WEDGE

FIBRELEASE®

PARTING WAX

MEGUIAR’S MOLD POLISH CONDITIONER AND RELEASE WAX

MOLD RELEASE CLIP SYSTEM

Description Price Item #Quart $10.75 13-AGallon $24.75 13-BCase (4 Gallons) $75.55 13-C

Description Price Item #24 oz Tin $10.25 1016-A7 lb Tin $42.05 1016-B

Description Price Item #11 oz Tin $16.15 118-ACase (12 Tins) $161.95 118-B

Description Price Item #FibRelease® $26.95 1153-A

Description Price Item #Air Injected Wedge $26.95 958-A

Description Price2-1/4” x 6” Rigid $3.15Item #: 64-A

Description Price Item #Fastening Clip Plier $21.55 792-A

Description Price Item #Fastening Clips $2.45 785-A

Description Price3” x 10” Rigid $5.35 Item #: 66-A

Description Price1-1/4” x 4” Flexible $2.15 Item #: 778-A

Description Price1-1/4” x 4” Rigid $2.15 Item #: 796-A










CHROMAVEILTM

C H R O M A V E I L T M

31

Design a new and exciting pattern right into your composite part! ChromaveilTM forms into the tightest of radii and corners without relief cuts or bubbles. Your finished parts will have a true woodgrain look or an exotic pattern that has never been previously available. Unlike traditional cultured marble or other types of cosmetic fiberglass fabrications, ChromaveilTM will last for years before allowing any glass pattern print through. Behind our #180 Clear Gel Coat, ChromaveilTM parts will have a supreme high gloss and marine-quality long life. Additionally, fiberglass fabrications for tubs, doors, woodwork, pools and more, no longer have to feel flimsy or only be offered as cheap alternatives to “real” substrates. Add our #448 6 lb. Poly Foam Core and you can achieve a heavy feel that will truly rival wood, granite or tile for upscale markets and applications. Of course, you still obtail all of the benefits of composites - long life, formability and corrosion resistance.

CHROMAVEILTM

CHROMAVEILTM SAMPLE PACKThis convenient Sample Pack contains a 12” x 12” Swatch for each of the ChromaveilTM patterns.


5001 - AMERICAN BEECH CHROMAVEILTM

5004 - WALNUT CHROMAVEILTM

5008 - BETTER THAN TILETM CHROMAVEILTM

5011 - FISH FANTASYTM CHROMAVEILTM

5002 - AMERICAN CHERRY CHROMAVEILTM

5007 - DESERT STORM CAMO CHROMAVEILTM

5009 - BETTER THAN GRANITETM CHROMAVEILTM

5012 - WET WHEN DRYTM CHROMAVEILTM

48” Wide, Vertical Repeat: 39.76”Horizontal Repeat: 20.24”








Custom Cut - min. qty of 10 yds10+ yds $15.95 /yard25+ yds $14.95 /yard50+ yds $13.95 /yard150+ yds $12.95 /yard300+ yds $9.95 /yard

Pre-Cut Length Price/Roll1 yd roll $24.953 yd roll $64.955 yd roll $94.95Swatch (12”x 12”) $2.95

PS Composites Inc.Markleysburg, PA





F A B R I C R A C K S32

The workhorseDesigned specifically for composites, this rack will hold up to six rolls of fabric and is suitable for even the heaviest materials. This rack is extremely stable and does not require rolls to be counter-balanced. Rack is predrilled to attach casters (sold separately) for portability. Dimensions: Width: 74” - Height (without rolls): 73.5” - Depth: 48” Freight shipping required

Perfect for Vertical SpacesThis four roll fabric rack comes predrilled and ready for floor mounting hardware. The extremely stable design does not require top mounting and is suitable for heavy mats and fabrics. However, this rack is not suitable for casters and is designed for floor mounting only. Floor mounting hardware sold separately. Dimensions: Width: 74” - Height (without rolls): 75.5” - Depth: 28.75” Freight shipping required

Sturdy and convenientThis mid-size rack is capable of hanging up to three rolls, with each bar able to hold up to 250 lbs. It is predrilled to attach casters (sold separately) for easy movement. Dimensions: Width: 74” - Height (without rolls): 40.5” - Depth: 42”

Keep materials organized and accessible. This workcenter has everything you need to keep your fabric and supplies organized and accessible. The single fabric rolling bar is 66” wide, holds up to 200 lbs., and is capable of handling a roll up to 32” in diameter - ideal for heavy mats, fabrics, and woven roving. The extra large work table is 96” wide and 36” deep. With a tension guide and tension bar, your fabrics can be held in place and the large work area allows plenty of room to maneuver. Two 72” wide shelves are plenty for your tools and supplies, The top shelf is 13” deep and comes with 7 dividers with multiple installation points. The lower shelf is 8” deep and allows 10-1/4” of storage space beneath the top shelf. This workcenter is also equipped with an extra sturdy storage drawer for easy access to your cutting tools and supplies. (Assembly Required.) Ergonomically designed at 35” from the floor, there is no need for stooping. Dimensions: Width: 96” Height: 76” Depth: 36” Freight shipping required

Easily work with multiple fabricsThis composite cutting station is ideal for storing and cutting fabrics. It has two bars for holding fabrics, each up to 52” wide, with the lower bar holding up to 150 lbs. and the top bar holding up to 70 lbs. With a tension bar and tension guide, fabrics can be pulled onto the table and kept smooth and even. The table area is 30” deep by 64” wide allowing plenty of room for cutting while allowing enough room to work. 35” from the floor, the ergonomic height is ideal for most adults. (Assembly Required.) Dimensions: Width: 64” Height: 59” Depth: 30” Freight shipping required

Make any fabric rack portable. (Set of 4)These high-quality swivel casters are fitted with 5” polyurethane wheels and can be easily installed on any of our fabric racks to allow even a full 6 roll rack to be moved by one person. Smooth ride keeps racks stable when moving, then engage the brakes to keep rack in place for unrolling and cutting

Wedge Anchors for Floor Mounting Fabric Racks.(Set of 4)

SIX ROLL FABRIC RACK

FOUR ROLL FABRIC RACK

THREE ROLL FABRIC RACK

COMPLETE COMPOSITEWORKCENTER

CUTTING STATION

FABRIC RACK CASTERS

WEDGE ANCHORS

Description Price Item #Six Roll Fabric Rack $749.95 1720-A

Description Price Item #Composite Workcenter $1,595.95 1723-A

Description Price Item #Cutting Station $749.95 1722-A

Description Price Item #Wedge Anchors $9.95 1738-A

Description Price Item #Four Roll Fabric Rack $599.95 2214-A

Description Price Item #Three Roll Fabric Rack $499.95 1719-A

Quantity Discount - Item #: 1720-A5+ $679.95

Quantity Discount - Item #: 1723-A5+ $1,495.95





Price Item #$159.95 1721-A



S C I S S O R S & F A B R I C A I D S33

Cut quickly and safely Give your hands a break and take the strain out of cutting. These electric shears make quick work of fiberglass and carbon fiber fabrics at the push of

a button. Its unique blade configuration cuts fabric with ease but can’t cut your fingers. Rechargable battery provides hours of use between charges and eliminates the need for awkward or restrictive power cords. Ships complete with two sets of blades, rechargable battery, battery charger, AC adapter, and transformer.

EC CUTTER

Description Price Item #EC Cutter $119.95 1700-A

Description Price Item #Gingher® Serrated Scissor $34.95 1731-A

Description Price Item #Muscle Shears $9.95 1732-A

Description Price Item #Detail Trimmers $24.95 1733-A

Description Price Item #Soft Grip Bent Trimmer $19.95 1734-A

Description Price Item #Resharpenable Scissors $69.95 429-A

Description Price Item #Featherweight Scissors $29.95 536-A








Parts & AccessoriesDescription Price Item #AC Adapter $24.95 1701-ARechargable Battery $44.95 1702-ABlade Set $34.95 1703-ABlade Set with Shoe $34.95 1704-ABattery Charger $44.95 1705-ATransformer $39.95 1714-A

Perfect circles every time Cut perfect circular patterns every time with this convenient rotary circle cutter. Easily adjustable center spike measures out the exact radius, creating circles from 1 7/8” to 8 1/2” in diameter. Ratchet handle is designed for right and left-handed use and reduces wrist fatigue. Rotary blade locks quickly into safety position for storage.

Best Kevlar® Scissor Ever The serrated edge on these scissors allows you to cut Kevlar® without pulling fibers along with the scissor. The serrated blade holds the fabric in place while the smooth blade cuts. Can be used for other fabrics but the same pair should not be used for Kevlar®and any other fabric.

Muscle through tough jobs. These scissors will even cut through many single layer laminations! They also do a great job on carbon, fiberglass and hybrid fabrics. One blade has a stainless steel serrated edge and the other stainless steel blade is smooth. The big, comfortable ambidextrous handles allow for a firm grip.

Fine, sharp tips for trimming in tight places. Soft, flexible, oversized bows are easy to handle and the stainless steel pointed ends cut all the way to the tips. These scissors will cut carbon, fiberglass, and hybrid fabrics with both right- and left-handed use.

Convenient Offset handles for easy table top cutting. Lightweight and comfortable, these stainless steel shears are perfect for straight cutting on delicate, lightweight fabrics as well as carbons and hybrids. The bent trimmer style will help keep the scissor cutting straight. Also offers a large lower bow for gloves to fit with ease and ambidextrous handles.

Years of useful life. These professional scissors have been relied upon for years for general purpose fiberglass work. Each pair features 12-1/2” trimmers that yield up to a 6” cut and are resharpenable. These 26 oz. Thru-hardened sheers should yield years of useful life!

Lightweight, durable, and reliable GINGHER® Scissors are lightweight, extremely sharp and comfortable. These 2-1/2 oz. scissors are perfect for use during the lay-up for a variety of purposes and can be soaked in acetone for easy clean up. We recommend saving one pair for only cutting Kevlar® and keeping a second pair for general use.

Cuts reinforcements like warm butter. Forget the jagged cuts and snagged yarns caused by scissors. Rotary cutters peform a smooth, clean cut and slice through fiberglass and graphite reinforcements in a snap. Simply squeeze the handle to move the blade into cutting position, lock it into place, and slice away. When finished, the blade locks back out of harm’s way for safe storage.

OLFA® ROTARY CIRCLE CUTTER

GINGHER® SERRATED SCISSOR MUSCLE SHEARS DETAIL TRIMMERS

SOFT GRIP BENT TRIMMERRESHARPENABLE SCISSORS

FEATHERWEIGHT SCISSORS

OLFA® ROTARY CUTTER







S C I S S O R S & F A B R I C A I D S34

Keep fabric edges from fraying Finally, a way to keep fabrics from fraying! Simply squirt a line where you wish to cut, allow to dry, and snip away. This unique liquid hold fabric ends together, preventing the unraveling commonly associated with looser weave styles. Note: areas of fabric saturated with fray check will not saturate with resin, so only use on portions that will be cut away.

Keep fabrics from rolling away The cost-effective way to keep fabrics neat and organized, these wire racks prevent fabrics from rolling off tables or shelves between cuts.

Economical throw-away Measuring Tape An easy way to measure out fabric in 1/8th of a yard increments. Roll this tape simultaneously with your fabric to calibrate your counter or to get a perfect yardage measurement. 100 yards per roll.

Make Exact Cutting Lines the first time We use it ourselves! Tape your fabric edge and then cut between the two printed lines. You get an even cut and prevent fraying on both edges. This cost effective solution to fraying of expensive fabrics comes off easily and leaves a negligible residue allowing the fabric to be laminated all the way to the edge. 55 yards per roll.

Industrial strength and made for thicker fabrics. With a 10-sided, self-sharpening blade, this scissor can make clean cuts through thick fiberglass and carbon fiber.

Years of use for perfect patterns Protect your table top with these heavy-duty cutting mats. Designed to withstand punctures from scissors, rotary cutters, or razor blades, these mats also create a smooth and consistent cutting surface. Mats are marked with measurements (to the 1/8”) and gridlines for accurate and easy calculations.

Write on any reinforcement These markers can write on Kevlar, fiberglass or carbon fiber without dragging the fibers! Now you can mark your own patterns without annoying tracers that may or may not fit your design. Pilot Marker utilizes a paint-like ink that can be applied with only minimal pressure. The Sharpie Marker applies clean, crisp lines for maximum visibility.

Make the right measurements This durable ruler features a frosted acrylic construction, making it easy to read on both light and dark surfaces. With gridlines and markings to 1/8” and angle measurements every 15 degrees, this handy ruler is much more than a simple straight edge.

DRITz® FRAY CHECK

WIRE RACK

EXACT YARDAGE TAPE

THE PERFECT LINE TAPE

INDUSTRIAL CORDLESS ELECTRIC SCISSOR OLFA® CUTTING MATS

FABRIC MARKERS

OLFA® RULER, 6” X 24”

Description Price Item #Dritz® Fray Check $4.95 1713-A

Description Price Item #Exact Yardage Tape $1.95 1730-A

Description Price Item #The Perfect Line Tape $14.95 1735-A

Description Price Item #Cordless Electric Scissor $499.95 2252-A

Description Price Item #Cutting Mat 12” x 18” $24.95 1709-A

Description Price Item #Pilot Silver Fabric Marker $6.95 925-A

Description Price Item #Olfa Ruler, 6” x 24” $29.95 1724-A

Description Price Item #Cutting Mat 24” x 36” $59.95 1708-A

Description Price Item #Sharpie Silver Fabric Marker $2.95 1925-A

Description Price Item #Cutting Mat 35” x 70” (3 pc) $209.95 1710-A











*parts & accessories available for #2252-A


SEE LAMINATE CUTTING TOOLS ON OUR WEBSITE WWW.FIBREGLAST.COM


RESIN APPLICATORS

R O L L E R S & A P P L I C A T O R S35

These brushes are so necessary to fiberglass work that we have spent considerable effort in finding the best source. Constructed of pure china bristle for the stiffness required to stipple resins into mats and fabrics. Epoxy potted bristles resistant to all solvents. Sanded wood handle for ease of grip and solvent resistance. We do not recommend these brushes for finish coats as they tend to leave bristles which are otherwise harmless in laminations. These brushes are all 1-3/4” trim length and 5/16” thick.

Plastic squeegees are a simple but essential tool for high performance laminating. They are the fastest way to evenly distribute resin in most full-scale applications. They are also useful for spreading fillers and general purpose fiberglass work. Rubber squeegees are excellent for forcing resin through high performance fabrics without the fear of snagging or distorting the costly fibers. The rubber conforms well to contours within the mold and provides better control than the plastic types. 6” wide.

Plastic Handles Durablue rollers for lightweight fabrics.

3/4” Diameter x 3” Wide This specialty roller is designed to form an impregnating spike for hard to reach air pockets. Easier clean up than bristle rollers!

2” Diameter x 1/4” Wide

1” Diameter x 3” Wide

Wooden Handles These long-lasting rollers are perfect for boat cloths and area that require a larger amount of pressure to release air bubbles.

Great for flat surfaces and gradual curves. The handle gives the ability to apply stronger pressure if need for heavier fabrics and stubborn air pockets.

CHINA BRISTLE BRUSHES

1” WidePrice Item #$0.95 34-A

1/2” Diameter x 3” WidePrice Item #$11.85 411-A

1/4” Diameter x 1.5” WidePrice Item #$11.85 764-A


1” Diameter x 3” WidePrice Item #$15.05 68-A








1.5” WidePrice Item #$1.05 31-A














Plastic

RubberSqUEEGEES

ALUMINUM ROLLERS

ALUMINUM SLOTTED PADDLE ROLLER

PLASTIC RADIUS ROLLER

BRISTLE ROLLER

ALUMINUM ROLLERS

PLASTIC ROLLERS

Description Price Item #Plastic Squeegees $0.85 62-APlastic Squeegees (24) $15.05 62-BRubber Squeegees $6.45 1108-ARubber Squeegees (6) $32.35 1108-B

Description Price Item #Aluminum Slotted Paddle Roller $16.15 940-A

Description Price Item #Plastic Radius Roller $12.95 415-A

Description Price Item #Bristle Roller $13.95 1105-A






RESIN APPLICATORS


R O L L E R S & A P P L I C A T O R S36

High Quality, Stands up to StyreneOur Quick Change Roller Cages fit our Saturation Sleeves or our Roller Covers. The Roller Cages are perfect for the fiberglass and composite industries. They have durable handles, allowing strong pressure to be applied, and the solid ends prevent resin and glass from entering (can easily be cleaned with acetone).

These barrel rollers are excellent for smaller contour and curves.

qUICK CHANGE ROLLER CAGES

ALUMINUM ROLLER SLEEVES

1” Diameter x 1.5” WidePrice Item #$12.95 1151-A


Aluminum - 1” Diameter x 2” WidePrice Item #$18.35 416-A



4”, 1/4” Nap Smooth Polyester Roller CoverPrice Item #$2.15 2947-A



7”, 3/16” Nap Mohair Roller CoverPrice Item #$6.45 2986-A

9”, 3/16” Nap Mohair Roller CoverPrice Item #$7.55 2999-A


4” Quick Change Roller CagePrice Item #$2.15 2233-A

4” Roller SleevePrice$8.55










Quantity Discount10+ $8.0525+ $7.55100+ $6.95





BARREL ROLLERS

Description Price Item #Bristle Roller $13.95 1105-AQuantity Discount - Item #: 1105-A10+ $13.4525+ $12.95100+ $12.35

#2245-A #2236-A #2242-A #2239-A#2246-A #2237-A #2243-A #2240-A#2247-A #2238-A #2244-A #2241-A

Slotted Paddle Roller Sleeves

FinnedRoller Sleeves

Bubble Buster Roller Sleeves

Long Groove Roller Sleeves

Economical roller for smaller jobs or small area of larger jobs. Use for small, flat surfaces or gradual curves.

Use it and throw it away

Tough Enough to Handle ResinThe most important thing about selecting a proper paint roller for fiberglass work is making sure the core will stand up to resin! A dissolving roller is not the way to start a job. These rollers are backed with two layers of polypropylene for repeated use and cleaning with acetone. But they are inexpensive enough to throw away.

ECONOMY WIRE HANDLE ROLLERS

3” ROLLER WITHWIRE HANDLE

POLYESTER & MOHAIR ROLLER COVERS

*Addition price breaks available on www.fibreglast.com*Addition price breaks available at www.fibreglast.com

*More paint supplies available atwww.fibreglast.com

Blue Dolphin Marine Towing and SalvageNorwood, MA



M E A S U R I N G & D I S P E N S I N G37

Shop Favorite These unique bottles are made to accurately dispense MEKP. The 16 oz bottle is graduated to measure up to 35 cc’s at a time, while the 32 oz bottle can measure up to 100 cc’s at a time. Simply squeeze the bottle until the upper vial is full, then release pressure on the bottle, leaving a precisely measured amount of catalyst in the vial. The MEKP can then be poured out with no dripping.

Easy drum pouring For standard 1” bungs

Safe and Convenient Perfect for screwing onto our 1oz MEKP bottles! These caps eliminate messy pouring, allow measurement by drops and can be capped for clean storage.

Long a staple of composite shops, these graduated cups are ideal for quick, easy measuring.

For pouring, scooping and measuring, these handy cups are ideal for resins, foam, fillers or mixes.

Graduated in ml and oz. The translucent beakers are simple

graduated disposable cups with a small spout to control pouring. The Tri-Pour Beakers have a special 3 spout design that is surprisingly handy for drip free pours. The simple paper inserts provide a short term cover when working with polyester, vinyl ester, epoxy resins or small batches of foam

The only way to know wet gel coat mil thickness This simple tool can save hundreds of dollars in

damaged material and labor. This is the only accurate method to determine gel coat thickness, and to achieve repeatable high quality results. Place the edge into the wet film, the last tooth marked is the thickness.

Will stand up to resins or acetone! Funnels are always handy in a composite shop. Large funnels facilitate pouring from 5 gallon pails and small funnels control pours from high viscosity materials like epoxy resin when measuring.

Perfect for Fillers These Polypropylene Scoops have a smooth surface which is great for the release of small

particles like microballons and fillers.

Pumps Any Resin, Any Ratio Eliminate messy cans, drips and spills. Easy single stroke pumps fit right into cans with accurate dispensing every time! To use with 3 to 1 mix, simply depress the pump 3 times for resin and once for cure. Clean with acetone between uses.

Different cans have different sized lids. Be sure to purchase the correct pump for your can! Our 824-A Resin Pump will fit only quart and gallon containers. For 5-gallon pails, our 823-A Resin Pump contains a wider lid and extended shaft attachment.

#55 is for both teaspoon and tablespoon measurements in one tool. Will not stand up to acetone.

MEKP DISPENSERS SPIGOT

MEKP CAPS

PLASTIC CUPS

GRADUATED MEASURING CUPS

BEAKERS & POUR STYLE CUPS

GEL COAT THICKNESS GAUGE

PLASTIC FUNNELS

SCOOPS

RESIN PUMPS

TEASPOON / TABLESPOON MEASURING SET

Description Price Item #16 oz MEKP Dispenser $8.55 166-A

Description Price Item #MEKP Caps $0.55 877-A

Description Price Item #Gel coat Thickness Gauge $10.75 122-A

Description Price Item #Spigot $5.35 51-A

Description Price Item #32 oz MEKP Dispenser $13.95 2266-A






Description Price Item #Resin Pump for Quarts/Gallons $6.45 824-AResin Pump for 5-Gallon Pail $6.45 823-A


4 oz FunnelPrice Item #$2.65 815-A

8 oz Cup/ScoopPrice Item #$3.15 821-A

16 oz Cup/ScoopPrice Item #$5.35 2263-A

22 cc ScoopPrice Item #$3.15 2264-A



10” FunnelPrice Item #$18.35 819-A





Quantity DiscountItem #: 815-A5+ $2.4510+ $2.1525+ $1.85






Quantity DiscountItem #: 819-A5+ $17.2510+ $16,1525+ $15.05





Description Price Item #1 oz Graduated Cups, (100) $7.55 59-B1 oz Graduated Cups, (5000) $172.75 59-C4 oz Cup with Lid $0.85 1378-A4 oz Cup with Lid (100) $70.15 1378-B

Description Price Item #50 ml Polypropylene Beaker $0.85 2285-A50 ml Polypropylene Beaker (100) $53.95 2285-B100 ml Tri-Pour Beaker $0.85 2287-A100 ml Tri-Pour Beaker (100) $53.95 2287-B250 ml Polypropylene Beaker $1.05 2286-A250 ml Polypropylene Beaker (100) $75.55 2286-B400 ml Tri-Pour Beaker $1.05 2288-A400 ml Tri-Pour Beaker (100) $75.55 2288-B800 ml Tri-Pour Beaker $1.35 2289-A800 ml Tri-Pour Beaker (100) $107.95 2289-B*paper inserts available for Tri-Pour Beakers




M E A S U R I N G & D I S P E N S I N G38

Get the Perfect Mix Every TimeThis versatile scale is the most accurate way to measure resin, regardless of the mix ratio. Also, weigh your dry fabric and only mix enough resin to achieve the desired 40-50% hand lay-up ratio. This scale will measure up to 5lbs or 2000g with accuracy to 0.1 oz/2g. Measure the resin, re-zero (tare) the scale, and pour in the proper amount of hardener. Mixing couldn’t be easier.

Mix Any Ratio These containers are ideal for mixing epoxy resins and polyurethane foams. The graduations display volumetric ratios for all kinds of mixes. You can add epoxy and then the hardener right on top or use two containers to mix later. Keep several pitchers on hand when mixing large batches of foam. Pour it, have it ready and you can mix it as you need it. In addition to the various mix ratios, the 16 and 24 oz. cups are graduated in milliliters and ounces. The 2.5 and 4 qt. pitchers are graduated in quarts, ounces, liters and milliliters.

For Accurate Fluid MeasurementsThe single scale, raised numerals allow for easy reading and large spouts facilitate pouring. These durable Polypropylene Cylinders easily stand up to resin and acetone for repeated use. They are perfect for pre-measuring resins and foams for later mixing. Graduated in milliliters only.

Check for Symmetry Use this great tool for checking symmetry like in our “Advanced Moldmaking and Plug Construction” video. The flexible curve can conform to any curve and is only limited to curves with radiuses of one inch or below. Simply smooth down over your radius and flip over to check for symmetry. These tools have a raised lip for tracing curves and are graduated in both inches and centimeters. Available in 12” and 24” lengths.

Flexible and Durable These are very flexible high quality stainless steel rulers that can be used to layout your project on the foam before you start cutting. These rulers can also be used to measure curved surfaces and they have raised edges to eliminate ink blots or smearing. The rulers are graduated with 16ths, 32nd, and metric to permit close work and are available in 12”, 24”, 36”, 48” and 60” lengths. Effectively Measure Small Amounts of Liquid

Syringes are handy when small, precise measurement is necessary. The 30 ml Syringe without needles will accept 1/8” I.D. tubing or # 106 needles. The 60 ml syringe has a catheter tip to help control dispensing and comes with a cap.

DIGITAL SCALEEz MIX CONTAINERS

GRADUATED CYLINDERS

FLEXIBLE CURVE RULER

FLEXIBLE STAINLESS STEEL RULERS

SYRINGES

Description Price Item #3 cc Syringe with Small Needle $0.75 105-A3 cc Syringe with Small Needle (100) $46.35 105-B30 ml Syringe w/o Needle $3.15 107-A30 ml Syringe w/o Needle (30) $53.95 107-B30 ml Syringe Needles $0.35 106-A30 ml Syringe Needles (100) $25.85 106-B60 ml Syringe, Catheter Tip $4.25 2275-A60 ml Syringe, Catheter Tip (25) $64.75 2275-B

Description Price Item #Digital Scale $140.35 1149-A

Description Price Item #12” Flexible Curve Ruler $10.75 2116-A

16 oz EZ Mix CupPrice Item #$1.05 2276-A

12” RulerPrice Item #$10.75 2163-A

50 ml Polypropylene CylinderPrice Item #$7.55 2281-A

Lid for 16 or 24 oz EZ Mix CupPrice Item #$0.55 2278-A





24 oz EZ Mix CupPrice Item #$2.15 2277-A


2.5 Quart EZ Mix PitcherPrice Item #$10.75 2279-A


Description Price Item #AC Adapter $21.55 1150-A

Description Price Item #24” Flexible Curve Ruler $21.55 2117-A



















Complete Mix, No Mess JIFFY MIXERS are the standard of the industry for mixing pigments and fillers with resins. These units will not splash and yet insure a thorough mix by pulling dense materials off the bottom and light materials off the top. Protected impellers guaranteed not to puncture container. All stainless steel makes clean up easy. 450-750 RPM recommended but the smaller ones can be used with a standard electric drill.

Nothing More Convenient Our paper mixing containers are ideal for mixes of all sorts. They will not break down under resins but will not stand up to acetone.

Our plastic mixing containers will stand up to resins, thinners and solvents.

Our Plastic Measuring Tub will stand up to resins, thinners and solvents, however, our paper mixing containers are ideal for mixes of all sorts but will not stand up to acetone.

Easily Store Your Resin. When used with a twist-on jar lid, these Polypropylene Jars provide airtight storage for your resins, hardeners, pigments or gel coat. Ideal for

applications when pigment has been mixed for a color match but the resin is not ready to be catalyzed. Available in 8 oz, 16 oz and 32 oz

Mixing sticks, 6” long. Mixing Paddles, 9”, 12” and 21” long.

Attach this Drum Mixer to standard-size 55 gallon drums through the 3/4” NPT hole, and you will be able to mix medium viscosity materials while simultaneously pumping liquid out. (100 psi max)

JIFFY MIXERS

PAPER TUBS

PLASTIC BUCKETS

1 PINT PAPER & PLASTIC MIXING TUBS

POLYPROPYLENE JARS

MIXING STICKS & PADDLES

DRUM MIXER

Description Price Item #Pint $26.95 319-A

Description Price Item #Gallon $32.35 320-A

Description Price Item #Drum Mixer $539.95 2250-A

Description Price Item #5-Gallon $86.35 321-A





Description Price Item #6” Mixing Stick (100) $3.75 58-A6” Mixing Stick (500) $15.05 58-B6” Mixing Stick (5000) $129.95 58-C9” Mixing Paddle $0.25 511-B9” Mixing Paddle (100) $17.25 511-C12” Mixing Paddle $0.25 512-B12” Mixing Paddle (100) $21.55 512-C21” Line Holder/Mixing Paddle $0.95 1600-A

Description Price Item #10 Pint Paper Mixing Tubs $4.25 14-A10 Pint Paper Mixing Tubs (100) $410.35 14-B5 Pint Paper Mixing Tubs $3.15 12-A5 Pint Paper Mixing Tubs (100) $302.35 12-B

Description Price Item #Resin Bucket - 5 Gallon $9.95 1402-AGallon Plastic Mixing Tubs $4.25 505-AGallon Plastic Mixing Tubs (100) $356.35 505-B

Description Price Item #1 Pint Paper Mixing Tub (25) $13.95 885-A1 Pint Paper Mixing Tub (50) $23.75 885-C1 Pint Paper Mixing Tub (500) $211.65 885-B1 Pint Paper Mixing Tub (1000) $410.35 885-DDeli Style Pint Plastic Measuring Tubs (25) $8.05 510-ADeli Style Pint Plastic Measuring Tubs (500) $107.95 510-B

Description Price Item #8 oz Polypropylene Jar $1.35 2269-A8 oz Polypropylene Jar Lid $1.05 2272-A16 oz Polypropylene Jar $1.55 2270-A16 oz Polypropylene Jar Lid $1.55 2273-A32 oz Polypropylene Jar $3.15 2271-A32 oz Polypropylene Jar Lid $2.65 2274-A

M I X I N G S U P P L I E S39 Purchase online or get more data at www.fibreglast.com



Mix a Quart of Resin and Hardener. This mixing set contains everything required to mix a quart of resin and corresponding hardener. Includes: (5) 1-Pint Paper Tubs, (1) 9 oz Cup, (1) 4 oz Cups, (1) 1 oz Cup, (1) Teaspoon/Tablespoon, (5) Mixing Sticks and (5) Pairs of Gloves. Typical Quart Lamination

This starter kit has everything you need to do a typical lamination involving a quart of resin. This kit includes: (1) 1/2” x 3” Wire Handle Plastic Roller ,(2) 1” Brushes, (2) 1-1/2” Brushes, (2) squeegees and (4) Pairs of Gloves.

Typical Gallon Lamination This starter kit has everything you need to do a typical lamination involving one gallon of resin. This kit includes: (1) 7” Birdcage Roller, (6) 7” Roller Covers (1/4” Nap), (1) 1” x 3” Plastic Roller, (6) 3” Brushes, (6) 2” Brushes, (6) squeegees and (12) Pairs of Gloves.

Typical 5 Gallon Lamination This starter kit has everything you need to do a typical lamination involving 5 gallons of resin. This kit includes: (1) 7” Birdcage Roller, (12) 7” Mohair Roller Covers (1/4” Nap), (1) 1” x 3” Plastic Roller, (6) 3” Brushes, (6) 2” Brushes, (6) squeegees and (1) Box of 100 Gloves.

Mix a Gallon of Resin and Hardener This mixing set contains everything required to mix a gallon of resin and corresponding hardener. Includes: (5) 1-Quart Paper Tubs, (3) 1-Pint Paper Tubs, (2) 9 oz Cups, (2) 4 oz Cups, (2) 1 oz Cups, (5) 9” Mixing Sticks, (1) Teaspoon/Tablespoon, (5) Mixing Sticks, and (8) pairs of gloves.

Mix 5 Gallons of Resin and Hardener This mixing set contains everything required to mix 5 gallons of resin and corresponding hardener. Includes (6) 10 Pint Paper Tubs, (6) 1 Pint Paper Tubs, (6) 9 oz Cups, (6) 4 oz Cups, (6) 1 oz Cups, (1) Teaspoon/Tablespoon, (12) Mixing Sticks and (12) Mixing Paddles.

qUART MIXING SET

qUART STARTER SET

GALLON STARTER KIT

5 GALLON STARTER KIT

GALLON MIXING SET

5 GALLON MIXING SET

M I X I N G S E T S & S T A R T E R K I T S40

Price Item #$8.55 588-APrice Item #

$16.15 591-A





The University of AkronAkron, OH



S A F E T Y41

Our #350-A is a 3M™ Half Facepiece Respirator which is molded in comfortable silicone, and features a four point cradle

suspension which won’t slide down the back of the head. The low profile design keeps cartridges out of field of view and permits glasses or goggles to be worn. We supply the mask complete with headgear, one pair of organic vapor cartridges, and one pair of prefilters so it is ready to be used right out of the box.

Replacement Cartridges, Prefilters and Prefilter Retainers are available to fit the #350-A Organic Vapor Respirator.

These economical goggles offer complete protection, direct ventilation and a

coated polycarbonate lens for high impact resistance without fogging.

Two strap dust and mist respirator gives excellent balance between performance and cost. Protects against coal, cadmium, chromium, lead, cotton dust, and silica. NIOSH/MSHA approved for dusts and

mists with a PEL not less than 0.05 mg/m3. Meets OSHA standards for use up to 10x PEL.

Ergonomic and economic, these glasses provide protection, comfort, and style.

Compatible with half-mask respirators and most prescription eyewear.

These inexpensive boot covers keep your feet clean and your floors cleaner. Take these covers off before leaving the work area so no dirt is tracked out of the shop.

These heavy-duty vinyl gloves stand up to solvents at a cost only slightly higher than the latex

surgeon’s gloves, but do not allow the “feel” of the surgeon’s gloves.

Our inexpensive latex gloves will withstand several hours use without pulling apart at the seams. These

surgeon-style hand protectors provide excellent feel and are highly recommended when using most all of our products. These gloves will not stand up to solvents.

These lightweight and inexpensive pants provide full lower body protection. Keeps your clothes clean and your skin safe from harsh chemicals and dirt. Can be machine washed.

These ultra-heavy duty 12”, 18 mil gloves are ideal where hands stay in resin and solvents. Tight fitting, durable and embossed grip.

These disposable caps keep resin and sanding dust out of your hair.

These disposable coats provide full body protection, combining the advantages of both coat and pants into one convenient suit. Lightweight, comfortable, and inexpensive. Can be machine washed.

These inexpensive disposable lab coats provide full upper body coverage during laminating and grinding. Keep dust and chemicals off clothes and away from your skin. These snap front coats are lightweight, cool and comfortable, eliminating common excuses for not wearing protective clothing. Can be machine washed.

ORGANIC VAPORRESPIRATOR

ORGANIC VAPOR CARTRIDGES

SAFETY GOGGLES

TWO STRAP DUST & MIST MASK

SAFETY GLASSES

DISPOSABLE BOOT COVERS

VINYL GLOVES

LATEX GLOVES

DISPOSABLE PANTS

FLOCK LINED LATEX GLOVES

SAFETY CAP

DISPOSABLE BODY SUIT

DISPOSABLE LAB COAT


Description Price Item #Prefilter Retainers (2) $5.35 351-APrefilters (2) $5.35 352-ACartridges (2) $15.05 353-A

X-LargePrice Item #$10.75 554-A

Price$7.55

Price$6.45

XX-LargePrice Item #$10.75 555-A





*Available in Large, X-Large and XX-Large

Description Price Item #Safety Goggles $12.95 539-A

Description Price Item #Dust & Mist Mask (box of 20) $32.35 851-B

Description Price Item #Safety Glasses $5.35 559-A

Description Price Item #Disposable Boot Cover $3.15 556-A

Description Price Item #Safety Cap $1.05 2230-A





*Available in Large and X-Large

Description Price Item #Large Single Pair $2.15 616-ALarge Dozen $21.55 616-BLarge Case (12 dozen pairs) $161.95 616-CX-Large Single Pair $2.15 617-AX-Large Dozen $21.55 617-BX-Large Case (12 dozen pairs) $161.95 617-C

Description Price Item #Small (Box of 100) $28.05 21-ASmall (Case of 4 Boxes) $99.35 21-BLarge (Bag of 100) $28.05 26-ALarge (Case of 4 Boxes) $99.35 26-BX-Large (Box of 100) $28.05 755-AX-Large (Case of 4 Boxes) $99.35 755-B

Description Price Item #Small (Box of 100) $18.35 3-ASmall (Case of 20 Boxes) $319.65 3-CLarge (Bag of 12) $3.75 10-ALarge (Box of 100) $18.35 10-BLarge (Case of 20 Boxes) $319.65 10-D




C L E A N U P42

The Industry Standard in Cleaning #9 is the standard of the industry for cleaning tools and brushes while working in polyester, vinyl ester, and epoxy resins. It is also the recommended solvent for removing greases and waxes from surfaces which are to be bonded, repaired or primed. It is not recommended for thinning resins or gel coats as this can lead to added pinholes and premature yellowing. Handle with the same care reserved for gasoline.

Use to Safely Dispense Acetone This dispenser keeps clean acetone on hand without the dangers of pouring from a can, and it reduces evaporation. Use to quickly wet a wiping rag when preparing the surface for priming or bonding. This 16 oz Polyethylene bottle with convenient squeeze spout and eye catching letters is a safe solution for positive identification of wash bottle contents.

Industrial Strength, Easily Disposable Wypall® X80 Paper Wipes are stronger than ordinary shop paper towels and much more absorbent. They are disposable but you won’t wipe once and throw away. You’ll get a lot of use out of one of these.

No Bleed with Acetone This standard of the industry is just a little better. You can use these towels with acetone without fear of turning your parts or fingers red! They are also excellent for grease and oil. 14” x 14”, machine washable.

Soft and AbsorbentThese knit/terry rags are sold by the pound and sizes and materials vary. Softer than paper and easily disposed of. Gentle enough for surface polishing.

Safer Cleaning of Small Parts This galvanized steel cans have a hinged lid and a spring loaded dasher screen which act as a fire baffle and allow sediment to sink to the bottom of the can.

Acetone At Your Fingertips The Wet Task® Refillable Wiping System includes one bucket and one dry roll of wipes. Add your own acetone to the bucket and over the wipes and you will have industrial strength wet wipes whenever you need them. The properly closed resealable cap will keep acetone from evaporating for weeks. It takes approximately 1 gallon of acetone to fill the bucket and saturatethe wipes.

Stands Up to Styrene and AcetoneThese handy scrub brushes are just right for cleaning messy tools, hands and surfaces. Unlike many other brushes that we tested, the bristles in these brushes hold up for many uses and do not break down in resin or acetone.

ACETONE

ACETONE DISPENSER

PAPER WIPES

GENERAL PURPOSE SHOP TOWELS

DISPOSABLE KNIT/TERRY RAGS

1 qUART SAFETY DAUB ACETONE CAN

WET TASK REFILLABLE WIPING SYSTEM

SCOURING BRUSH

Description Price Item #Acetone Dispenser $9.65 160-A

Description Price Item #Paper Wipes $19.95 2205-A

Description Price Item #General Purpose Shop Towels $14.95 2200-A

Description Price Item #Disposable Knit/Terry Rags $9.95 2203-A

Description Price Item #Scouring Brush $4.95 2207-A







Description Price Item #Refillable Wiping System $39.95 2204-ARefill Roll for Wet Task System $19.95 2206-ARefill Roll for Wet Task System (4) $69.95 2206-B



BOOKS & VIDEOS

B O O K S & V I D E O S43

By Fibre Glast Developments, 190 Total Minutes All five of our How-To

videos on a convenient 2 DVD set. A total of 190 minutes of the most complete guide for using composite materials available anywhere! The Complete Fiberglass and Composite Library contains The Basics of Fiberglass, A Step-By-Step Guide to Molding Fiberglass, Advanced Moldmaking and Plug Construction, Vacuum Bagging and Sandwich Core Construction and The Art of Moldless Composites.

THE COMPLETE FIBERGLASS & COMPOSITE LIBRARY ON DVD














By John Wanberg, 2009, 144 PagesThe “Handbook of Composite Fabrication” covers all of the major composite manufacturing processes in a single, concise

volume. Perfect for all levels from beginners to experienced. While most books on composites approach the subject from a very technical standpoint, this book presents practical, hands-on information about these versatile materials.

By Castcraft, 1992, 200 combined pages. In addition to fiberglass construction, these guides discuss plaster, latex molding, rubber gelatin and flexible molding wax. Designed

for those interested in craft applications, these guides are an excellent source of information to anyone interested in casting and molding.

By Tex Smith, 2003, 225 Pages The art of chopping tops to make custom cars or street rods is one that is often shrouded in mystery.

In this book, customizer Tex Smith takes you inside this process and presents it as something even the amateur car enthusiast can do. In addition to the step-by-step guide, this book also includes over 50 examples of cars and trucks that have been chopped to produce a stunning new look.

By Leroi Tex Smith, 1994, 199 PagesThis book is a great guide for anyone considering a full scale project. It includes plenty of pictures

and descriptions of mock-ups, plugs, male and female molds, and the parts produced in them. Written with a voice of personal experience, the author also includes a fitting discussion of ready-made car components.

By Jim Richardson, 1994, 166 Pages This book is designed to help the do-it-yourself restorer avoid common problems such as costly mistakes and wasted materials.

Featuring step-by-step techniques, this guide offers advice on all facets of restoring a classic including how to: rebuild an engine, apply paint, replace upholstery, repair fuel tanks, overhaul brakes, rebuild carburetors, and much more. All information is general enough to be used for any project, regardless of car make or model year.

By Precision Fiberglass, 100 Minutes Learn how to mix you own matching color gelcoat, fill scratches and voids on the gelcoat surface, spray gelcoat as well as

sand and polish the gelcoat to a new boat finish.

Fiberglass Gel Coat Damage By Pelican, 54 Minutes. Learn how to make fiberglass repairs as you look over the shoulder of a professional fiberglass repairman with 20 years

experience. Using easy to follow, step-by-step procedures he repairs a crack in the bottom of a bass boat.

By Andrew Marshall, 2001, approx. 150 pages. Anything but basic! This book begins with a simple discussion of fabrics and resins but continues through sandwich core

structures and engineering with the materials. Stress testing and load analysis are also covered.

By Allan H. Vaitses, 1988, 171 PagesAs the definitive guide for fiberglass boat repair and beautification, this book covers not only cosmetic dings

and scratches, but also major repairs of structural damage to hull and decks. This book will show you how to: repair or replace gelcoat flaws and damage, stregthen a weakened hull or deck, repair a cored laminate, repair water-saturated deck cores, and more.

By Jack Wiley, 1988, 260 Pages This book offers a thorough general introduction to fiberglass fabrication and repair and addresses the reluctance

many newcomers have to doing fiberglass work. He covers reasons for doing your own repairs as well as materials, equipment and health and safety. About 50 pages are dedicated to various types of repair but molding and construction projects are covered as well.

By John Wanberg, 2010, 144 Pages. Composites Fabrication Handbook #2 is written for those who want to enhance the quality and performance of their composite

projects. Learn what it takes to truly optimize a composite lamination for high-performance use. Basic mold making is covered in this book to help fabricators produce effective mold systems from a variety of molding materials. Several advanced molding techniques are demonstrated in-depth, including vacuum bagging, trapped-rubber insert molding, inflatable bladder molding, or resin transfer molding techniques. In the spirit of Composites Fabrication Handbook #1, this book presents each subject in a hands-on, practical way.

By Forbes Aird, 1996, 153 Pages Although the examples are mostly automotive and marine, this book is ideal for a comprehensive, non-engineering discussion of the

complete spectrum of composite materials, techniques and applications. An excellent introduction for anyone entering the field of fiberglass and composites intending to work in a home or small shop. Plenty of safety and shop design tips as well.

COMPOSITE MATERIALS FABRICATION HANDBOOK #1

CASTCRAFT GUIDES

HOW TO CHOP TOPS: RODS, CUSTOMS, TRUCKS, RACE CARS & MORE

HOW TO BUILD FIBERGLASS HOT RODS, CUSTOMS & KIT CARS

CLASSIC CAR RESTORER’S HANDBOOK: TIPS & TECHNIqUES

COSMETIC GEL COAT & FIBER-GLASS REPAIR, VOLUME 1 (DVD)

FIBERGLASS REPAIRS MADE EASY VOLUME 1 (DVD)

COMPOSITE BASICSSEVENTH EDITION

THE FIBERGLASS BOAT REPAIR MANUAL: COSMETIC & STRUCTURAL

THE FIBERGLASS REPAIR & CONSTRUCTION HANDBOOK

COMPOSITE MATERIALS FABRICATION HANDBOOK #2

FIBERGLASS & OTHER COMPOSITE MATERIALS


CONTACT USCUSTOMER PICTURES

ON THE COVER1.800.330.6365

937.833.6555

[email protected]

Fibre Glast Developments Corporation385 Carr DriveBrookville, Ohio 45309

Customer Service

Email

Fax

8:00 am - 8:00 pm EASTERN TIME, MON - FRI*OPEN UNTIL 5:00 pm PACIFIC TIME!

SIGN UP FOR FIBRE GLAST EMAILS!VISIT WWW.FIBREGLAST.COM TO JOIN OUR EMAIL LIST.YOU WILL RECEIVE IMPORTANT EMAIL UPDATES THAT CAN SAVE YOU MONEY! OFFERS INCLUDE: PRODUCT SPECIALS, ONLINE ONLY SPECIALS, PERCENTAGE DISCOUNTS, NEW PRODUCT ANNOUNCEMENTS, AND EXCLUSIVE UPDATES!

ON THE COVER AND THROUGHOUT THIS CATALOG, FIBRE GLAST FEATURES SEVERAL CUSTOMER PICTURES. WE ARE HONORED TO DISPLAY THEM HERE AND ON OUR WEBSITE. IF YOU WOULD LIKE TO BE INFORMED OF FUTURE ‘SEND US YOUR PICTURE’ CAMPAINS, JOIN OUR EMAIL LIST. WANT TO SEE MORE CUSTOMER PICTURES? VISIT WWW.FIBREGLAST.COM TO VIEW THE PHOTO GALLERIES!

ORDER BEFORE 2:30 ET FOR SAME DAY SHIPPING!

SAME DAY SHIPPING!VISIT OUR WEBSITEWWW.FIBREGLAST.COM

EASY & SECURE ONLINE ORDERING

READ HOW-TO WHITEPAPERS & WATCH HOW-TO VIDEOS IN THE LEARNING CENTER.

GET AN ESTIMATE OF THE AMOUNT OF MATERIALS YOU WILL NEED WITH THE MATERIALS CALCULATOR.

CHECK ORDERS & TRACK SHIPMENTS.

ODP Motorsport EngineeringCoeur d’Alene, ID

Elite CustomzCincinnati, OH

1.800.330.6365WE’RE OPEN

LATER!8:00 am - 8:00 pm ET

MON-FRIWWW.FIBREGLAST.COM

CREATE A PIECE OF ART WITH THESTRENGTH OF CARBON FIBER.

6 CARBON FIBER PATTERNS AVAILABLE.

385 Carr DriveBrookville, OH 45309

EASY TO ORDER!WWW.FIBREGLAST.COM

1.800.330.6365

Browse a huge selection of products. Purchase online through an easy, secure process.

Speak with a knowledgeable sales representative. Place or inquire about an order, obtain a quote, or get technical information about our products.


ROOK

LABYRINTH ROSWELL

GRANDMASTER WASP

ATOMIC


CARBON FIBER - 3K, 12x12, 5.7 Oz/YD2, 50” WIDE, .014” THICK CARBON FIBER - 3K, 12x12, 5.7 Oz/YD2, 50” WIDE, .014” THICK

CARBON FIBER - 12K, 10x10, 19.2 Oz/YD2, 50” WIDE, .03” THICK CARBON FIBER - 3K, 12x18, 7.3 Oz/YD2, 50” WIDE, .016” THICK


PAGE

1

Fib Erg Last Catalog

Documents

Transcript of Fib Erg Last Catalog