F&F LAB MANUAL

download F&F LAB MANUAL

of 18

Transcript of F&F LAB MANUAL

  • 7/31/2019 F&F LAB MANUAL

    1/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    LIST OF EXPERIMENTS

    1. PRACTICE FOR PREPRATION MOULDING SAND MIXTURES

    (1 session)2. PRACTICE FOR MAKING SAND MOLDS USING DIFFERENT

    PATTERNS (2 sessions)

    3. PRACTICE FOR MELTING ALUMINUM AND ITS ALLOYS (2

    sessions)

    4. PRACTICE FOR MAKING SAND CASTINGS USING DIFFERENT

    PATTERNS (3 sessions)

    5. PRACTICE FOR MAKING CORES FOR SAND CASTING

    PROCESS (2 sessions)6. PRACTICE FOR MAKING PERMANENT MOLD CASTINGS(2

    sessions)

    7. PRACTICE FOR MAKING SAND SAMPLES USING SANDRAMMER

    (1 session)

    8. TESTING OF GREEN & DRY STRENGTHS OF DIFFERENT SAND

    MIXTURES (2 sessions)

    9. TESTING OF PERMEABILITY OF A GIVEN SAND SAMPLEUSIND PERMEABILITY TESTER (1 session)

    10. TESTING OF A.F.S. CLAY CONTENTS IN THE GIVEN SAND

    SAMPLE USING SAND WASHER (1 session)

    11. Theory and Practice for using coverall fluxes, exothermic

    compounds, degassers and mold coats. (1 session)

    12. Analysis of Casting Defects. (1 session)

    13. A study on molding equipments and machines. (1 session)

    14. A metallographic study of Rolled, Forged, Extruded and

    Cast Structures. (2 session)

  • 7/31/2019 F&F LAB MANUAL

    2/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 1

    PRACTICE FOR PREPARATION OF MOLDING SAND

    MIXTURES

    Overview:Silica sand (SiO2) is used more frequently for making castings than any other mouldingmaterials. It is relatively cheap, and has sufficiently refractoriness even for steel foundry

    use. A suitable bonding agent (clay or molasses) is mixed with the sand; mixture is

    moistened with water to develop strength and plasticity and to make the aggregatesuitable for molding. A definite mulling action is always required for thorough mixing, in

    which sand grains, bonding agent, and water are rubbed intimately together. Different

    types of sand mullers are used to serve this purpose.

    Equipment:A. Sand Muller

    B. Hot Tray

    C. Shovel

    Chemicals / Materials:Sand, Molasses and Water.

    Procedure:

    1. Take silica sand and stack it over hot tray with the help of a shovel.2. Put on the fire and heat the sand for sometime.3. When it is sufficiently hot, throw it into the pan of muller with a shovel.

    4. Then add some amount of molasses in the sand and switch on the muller. The wheels

    rotation inside the muller will thoroughly mix up sand and molasses.5. Continue adding and mixing molasses in the sand until sufficient strength and

    plasticity is developed in the sand-molasses mixture.

  • 7/31/2019 F&F LAB MANUAL

    3/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 2

    PRACTICE FOR MAKING SAND MOLDS USING DIFFERENT

    PATTERNS

    Overview:

    Silica sand (SiO2) is used more commonly for making castings than any other molding

    materials. It is relatively cheap, and has sufficiently refractoriness even for steel foundry

    use. A suitable bonding agent (clay or molasses) is mixed with the sand; mixture is

    moistened with water to develop strength and plasticity and to make the aggregate

    suitable for molding. The resulting sand mixture is easily prepared and molded around

    various shapes to give satisfactory casting of almost any metal.

    The fundamentals of mold making are simple, but expert hand molding requires much

    skill and practice. Production line work is done today by machine molding, in which

    nearly all operations are automatic. The skilled molder is replaced by a relatively

    untrained machine operator.

    Equipment:

    A. Flask or Molding BoxB. Rammer

    C. Riddle

    D. Wooden or Steel Board

    E. Different Patterns

    F. Draw spikes

    Chemicals / Materials:

    Molding Sand, Graphite Powder, Molasses

  • 7/31/2019 F&F LAB MANUAL

    4/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    Procedure:

    1. First of all place the wooden or steel board (bottom board) on the table or floor.2. Place the drag-half of the flask on the bottom board and position drag-half of the

    pattern in it.3. Sprinkle some amount of graphite powder in the flask and over the pattern to produce

    smooth surface finish. It also acts as a parting agent.

    4. Now, fill the drag-half of the flask with molding sand keeping the pattern in position.

    5. Ram the molding sand in the flask with the help of a rammer.6. Continue adding and ramming the sand until it is densely packed in the flask.

    7. When the flask is properly rammed, then use a metal strip to remove excess sand

    from the upper surface.8. Now, place a second flat board upside down on the mold and flask, clamp it and over

    turn the whole.

    9. Remove the first bottom board which is now on top and sprinkle some amount ofgraphite powder (parting powder) on the surface of mold to finish it.

    10. Now, position the cope-half of the flask over drag and also the cope-half of the

    pattern.

    11. Place two rods vertically on either sides of the pattern, at a suitable distance, toproduce pouring basin and risering system.

    12. Fill the cope-half with molding sand keeping the pattern and rods in position.

    13. Ram the molding sand in the flask with the help of a rammer.14. Continue adding and ramming the sand until it is densely packed in the cope.

    15. When the flask is properly rammed, then use a metal strip to remove excess sand.

    16. Now, remove the rods from the cope-half and as a result holes for spruce and riserwill be produced.

    17. Separate cope and drag portions of the flasks from each other, use draw spikes to

    remove the pattern from the mold.18. Cut the in-gates in the mold and again sprinkle some amount or graphite powder over

    the surface of mold to finally finish it.

    19. If necessary, position the cores in the cavity of the mold and close the mold again by

    placing cope again atop the drag.20. The mold is ready for pouring.

  • 7/31/2019 F&F LAB MANUAL

    5/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 3

    PRACTICE FOR MELTING ALUMINUM AND ITS ALLOYS

    Overview:Manufacture of castings is essentially a matter of heat transfer in one or another form.Heat is first added to the cold, solid metal (scrap or ingot) for melting and for

    superheating the molten metal until it is fluid enough to pour into a mold. Various typesof furnaces are used for this purpose e.g. crucible furnace, electrical furnaces, cupola

    furnace etc. Heat is then extracted from the metal by mold to re-form it into a solid, cold

    body of desirable size and shape.The furnace which is most commonly used for melting non-ferrous metals and alloys

    is crucible furnace.

    Equipment:

    A. Pit Furnace

    B. Crucible

    Chemicals / Materials:

    Aluminum scrap, Flux and degasser

    Procedure:

    1. Take required amount of aluminum scrap and put it into the pit furnace crucible.

    2. Switch on the blower and turn on the gas valve.3. Then, put on the fire so that metal in the crucible can be melted.

    4. Continue supplying heat to the metal until it is completely liquefied and fluid enoughto pour into a mold.

    Fluxing:

    Assignment

    Degassing:

    Assignment

  • 7/31/2019 F&F LAB MANUAL

    6/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 4

    PRACTICE FOR MAKING SAND CASTINGS USING

    DIFFERENT PATTERNS

    Overview:

    The casting process is the oldest, most versatile, and the most flexible process for

    forming metals. Basically, it consists of introducing molten metal into a cavity or mold of

    desired form and allowing the metal to solidify. There is practically no limit to the size,shape, and alloy of the casting that may be made. Castings regularly produced range from

    tiny dental inlay of rare metals to complicated steel castings exceeding 2000 ton in

    weight. Almost any article may be cast with proper technique.In sand casting, a mold is produced by shaping a suitable refractory material to form a

    cavity of desired shape, such that a liquid metal can be introduced into this cavity. The

    mold cavity has to retain its shape until the molten metal has solidified and the casting isseparated from the mold.

    There are also some other types of casting processes: e.g. permanent mold casting, die

    casting, plaster casting, investment casting, squeeze / semi solid casting, slush casting,

    shot casting etc.

    Equipment:

    A. Sand Molds with different shapes of cavitiesB. Crucible

    Chemicals / Materials:Molding Sand, Aluminum metal

    Procedure:

    1. First of all, prepare sand for sand molding according to the procedure described in

    Experiment # 1.

    2. Then, prepare a sand mold according to the procedure described in Experiment # 2.3. After the preparation of sand mold, melt aluminum metal or any available aluminum

    alloy in a pit furnace.

    4. When the metal is liquid enough to pour into the mold, put off the fire and hold the

    crucible with the help of a holder.5. Place some weight on the mold and pour the molten metal into the mold through the

    spruce or pouring basin.6. Continue pouring until the molten metal comes out of risers of the mold.

    7. Allow the metal to solidify in the sand mold for some time.

    8. When the metal in the mold is solidified, break the sand mold with the help of

    breakers to remove the required metal casting.9. Finally, the casting is machined to get the finished shape.

  • 7/31/2019 F&F LAB MANUAL

    7/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 5

    PRACTICE FOR MAKING CORES OF SAND CASTING

    PROCESS

    Overview:

    Cores are used to obtain the internal configurations of different castings. Cores are

    usually made of synthetic sand, although clean, natural sand containing only 1 to 2 %clay can be used. Cores may also be made of green sand used in the dried condition. Most

    frequently, however, they are bonded with organic agent such as linseed oil, cereals,

    molasses etc may be added to make the raw mixture stronger. The basic advantage of

    organic core binders (as compared to clays) is that they break down under the heat ofmetal (have collapsibility) and so can be easily removed from the casting as shakeout.

    Equipment:

    A. Core Box

    B. Rammer

    C. Chemicals / Materials:

    Chemicals / Materials:

    Moulding Sand (mixture of sand & molasses).

    Procedure:

    1. Take a core box and fill it completely with molding sand (mixture of sand &

    molasses).

    2. Insert iron wires for reinforcement.3. Then ram the molding sand present in the core box with the help of a rammer.

    4. Continue adding and ramming the moulding sand until the sand is densely and fully

    packed in the core box.5. Then, open the core box and carefully remove the core from it.

    6. Bake this core in an oven at about 230oC to develop the strength in core and to

    remove gases.

    7. After baking, wash the core with refractory slurry to improve the casting surfacefinish.

  • 7/31/2019 F&F LAB MANUAL

    8/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 6

    PRACTICE FOR MAKING PERMANENT MOLD CASTINGS

    Overview:

    In permanent mold casting method, molten metal is poured into metal molds and around

    metal cores. The metal molds are coated with a mold surface coating and preheatedbefore being filled with molten metal. A pre-measured amount of molten metal is poured

    into the permanent mold under gravity.

    Permanent molds are made in two halves; they may be designed with vertical parting

    line or with horizontal line as in ordinary sand molding. The mold material is usually agood grade of cast iron, although die steel, graphite, copper, and aluminum are also being

    used. Cores for permanent molds can be sand, plaster, collapsible metal cores, or simply

    heavily tapered metal cores which are removed while the casting is still hot.Permanent mold castings have been made commercially of tin, zinc, lead, aluminum,

    magnesium, copper, and cast iron, and from their alloys. Higher production rates are

    obtained in permanent mold castings than sand casting.

    Equipment:

    A. Permanent Metal Mold

    B. Brushes

    Chemicals / Materials:

    Aluminum scrap, refractory wash

    Procedure:

    1. Clean the mold by brushing or blasting with warm air.2. Maintain it at proper casting temperature by a gas or oil flame.

    3. Paint or spray the mold surface with a thin refractory wash or blacken it by depositing

    carbon from a reducing oil or gas flame.

    4. Insert cores, if necessary and close the mold by hand or automatic action if available.5. Pour the molten aluminum metal from the crucible into permanent mold.

    6. Allow the sufficient time for the casting to solidify.

    7. Then, open the metal mold and eject the casting from it automatically or by hand.8. Finally, machine the casting to get the finished shape.

  • 7/31/2019 F&F LAB MANUAL

    9/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 7

    PRACTICE OF MAKING SAND SAMPLES USING SAND

    RAMMER

    Overview:

    The sand rammer is a machine for preparing specimens for testing of the permeability

    and strength of moulding sand and is comprised mainly of a base, ram, tamping bar and

    lever.

    The machine is so constructed that the ram is brought up by the crank and is then

    caused to drop to strike and drive down the tamping bar at the lower end of which is fixed

    a tamping plate which slides into a sand tube to press the sand tube into a certain size

    with certain energy.

    Equipment:

    A. Sand Rammer

    B. Sand tube

    C. Sand stripping bar

    Chemicals / Materials:Testing sand

    Figure: Sand Rammer

  • 7/31/2019 F&F LAB MANUAL

    10/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    Operating Procedure:

    Preparation of Strength Test Specimen:

    1. Set the sand tube in the tube rest for about 15 mm, and holding it by hand, introduce

    about 140 g to 175 g of the test sand gently so that the sand surface is level.

    2. Next, pull the handle toward you to force the tamping bar up, then load the sand tube

    having the sand charged together with the rest on the base, and introduce the ramming

    head quietly into the sand tube until it is held by the sand surface.

    3. Then, turning the lever forward, perform ramming three times.

    4. With the sand thus rammed, if the pointer provided on the tamping bar stops within

    the tolerable range on the scale, the compacted sand is usable as a test specimen of a

    standard size (height 50 mm).

    5. The tolerances 1 mm graduated above and below the base line, and if the pointer

    does not remain within the tolerable range, such specimen is not usable as a testspecimen, so that it should be discarded.

    6. Then, adjusting the quantity of sand to be introduced in the sand tube properly, repeat

    the foregoing procedure.

    7. When a specimen of standard size is obtained, raise the ramming plate, remove the

    sand tube and set it over the sand stripping bar to withdraw the standard sand

    specimen from the sand tube.

    Preparation of Permeability Test Specimen:

    1. Set the sand tube on the rest, and prepare the test specimen, as in the case of the

    strength test specimen, with about 140 g to 175 g of the test sand fed.

    2. The specimen height shall comply with the standard 50 mm (tolerance 1 mm).3. In the case of testing the permeability of green sand, the test specimen should not be

    withdrawn from the sand tube but be applied to the permeability tester immediately

    together with the sand tube.

    Caution:

    The machine is subjected to considerable impact in use so that it should be installed in the

    rigid concrete base preferably in a height of 500-600 mm.

  • 7/31/2019 F&F LAB MANUAL

    11/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 8

    DETERMINATION OF GREEN & DRY STRENGTH OFDIFFERENT SAND MIXTURES

    Overview:

    Strength or bond strength is the property of sand whereby it offers resistance to

    deformation and enables the sand to hold together under pressure. Green strength is

    referred to the strength of moist or tempered sand whereas dry strength is strength of sand

    dried at 110oC. The green strength of sand is usually lower than its dry strength. Bond in

    moulding sand is due to the presence of binders such as clay, core gum, molasses, linseed

    oil etc.

    Universal Sand Strength Testing Machine:

    The Universal Sand Strength Testing Machine consists of three major parts; frame,

    pendulum weight and pusher arm. The pusher arm is motivated by means of a small

    handwheel, which, through a gearbox, rotates a pinion engaged in a rack on the quadrant.

    The pendulum weight swings on a ball bearing and can be moved by the pusher arm, via

    test specimen, from a vertical position, with a consequent increase of a load on the test

    specimen. A magnetic bar is moved up the calibrated scale by the pendulum weight and

    indicates the point at which the specimen collapses. The machine can be calibrated in g /

    cm3.

    Figure: Universal sand testing machine

  • 7/31/2019 F&F LAB MANUAL

    12/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    A. Green Compression Strength:

    Test Procedure:

    1. Place the compression heads in the lower position as shown in the figure.

    2. Raise the weight arm slightly and insert an A.F.S. standard 50 mm X 50 mm test

    specimen between the compression heads so that the face that was uppermost in the

    ramming operation is facing the right-hand compression head. Care should be taken

    not to damage the specimen.

    3. Ensure that the magnetic rider is resting against the pusher plate and that there is at

    least 6mm clearance between the rubber bumper and the lug on the weight arm. If this

    clearance is insufficient, it means that the specimen is smaller than the permitted

    tolerance and should be discarded.

    4. Apply a load to the test specimen by turning the hand wheel at uniform rate

    (approximately 30 g / cm3 / sec) until the specimen collapses.

    5. Record the reading shown on the lower edge of the magnetic rider, reading the scaledesignated Green Compression Strength.

    6. Return the weight to zero by gently reversing the rotation of the hand wheel. Remove

    the sand from the compression heads.

    B.Green Shear Strength:

    Test Procedure:

    1. Place the shear test heads in the lower position in the machine, with the head having

    the half round holder attached to it in the pusher arm.

    2. Raise the weight arm slightly and insert an A.F.S. standard 50 mm X 50 mm test

    specimens between the heads.

    3. Ensure that the magnetic rider is resting against the pusher arm and that there is 6mm

    clearance between the rubber bumper and lug on the weight arm.

    4. Apply the load uniformly until the specimen shears.

    5. Read the lower edge of the magnetic rider on the scale designated Green Shear

    Strength.

    6. Return the weight to zero by reversing the rotation of the hand wheel. Remove the

    sand from the shear heads.

  • 7/31/2019 F&F LAB MANUAL

    13/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    C.Dry Compression Strength:

    Test Procedure:

    1. Place the compression heads in the top position of the machine. This position

    increases the load applied by factor of 5.2. Prepare A.F.S. standard 50 mm X 50 mm test specimen in the usual way and dry in

    an oven at 110oC for few hours.

    3. When cool, place in position between test heads and adjust clearance between rubber

    bumper and the lug on weight arm to approximately 13 mm using the adjustingscrews in the pusher arm.

    4. Apply the load as for Dry Compression until the specimen collapses.

    5. Red the scale designated Dry Compression Strength according to the test heads

    being used.6. Return the weight to zero by reversing the rotation of the hand wheel. Remove the

    sand from the compression heads.

    D.Dry Shear Strength:

    Test Procedure:

    1. Place the shear heads in the top position of the machine. This position increases the

    load applied by factor of 5.2. Prepare A.F.S. standard 50 mm X 50 mm. test specimen in the usual way and dry in

    an oven at 110oC for few hours.

    3. When cool, place in position between test heads and adjust clearance between rubber

    bumper and the lug on weight arm to approximately 13 mm using the adjustingscrews in the pusher arm.

    4. Apply the load as for Dry Shear until the specimen shears.

    5. Red the scale designated Dry Shear Strength according to the test heads being used.

    6. Return the weight to zero by reversing the rotation of the hand wheel. Remove the

    sand from the shear heads.

  • 7/31/2019 F&F LAB MANUAL

    14/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 9

    DETERMINATION OF PERMEABILITY OF GIVEN SAND

    SAMPLE USING PERMEABILITY TESTER

    Overview:

    Permeability is that property which allows gas and moisture to pass through the moulding

    sand. It is determined by measuring the rate of flow of air through A.F.S. standardrammed specimen under a standard pressure. The volume of air in cm3 / min. passing

    through a specimen of length 1 cm. and cross sectional area of 1 cm 2 under a pressure

    difference of 1 cm. water gauge is called Permeability Number.

    Permeability Number:

    The volume of air passing through a sand specimen 1 sq. cm area and 1 cm. in height at apressure of 1 gram per square centimeter in 1 min. is called the Permeability Number and

    is computed by the formula:

    P = (v x h) / (p x a x t)

    Where,

    P = Permeability Number

    v = Volume of air passing through the specimen (cubic centimeter or in mil)h = Height of specimen (centimeters)

    p = Pressure difference between upper and lower surfaces of test specimen (in centimeterof water column)

    a = Cross-sectional area of specimen (square centimeter)

    t = time (minutes)

    Permeability Meter:

    The body of the Permeability Meter is an aluminum casting of a water tank and base.Inside water tank floats a balanced air drum carefully weighed and designed to maintain

    constant pressure of 10 cm during its fall.

    The outlet from the air drum is connected to a centre post in the base via three way air

    valve. The centre post incorporates a pipe for measuring pressure, which is connected tothe water manometer and an expandable O ring for sealing the specimen tube. It also

    accommodates the orifices.

  • 7/31/2019 F&F LAB MANUAL

    15/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    Equipment:

    A. Sand Permeability Tester

    B. Testing sand specimens

    Figure: Sand Permeability Tester

    A.Standard Permeability Test:

    Test Procedure:

    (A.F.S Standard Time and Pressure Method)

    1. Check that the open orifice is in the position in the centre

    2. Prepare an A.F.S. standard specimen of sand. Before stripping from tube place inposition on the centre post and seal by rotating the knurled ring anti-clockwise.

    3. Check water level in the tank. Turn air valve to NENT and slowly raise drum until

    it is out of water.

    4. Allow the air drum to descend by turning the air valve to a position midway betweenCLOSED and VENT.

    5. Time the descend of the air drum between zero and 2000 ml mark with a stop watch

    and record the pressure indicated on the manometer during the descend of the drum.6. Calculate the permeability by applying the given formula.

  • 7/31/2019 F&F LAB MANUAL

    16/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    B.Dry Permeability Test:

    The permeability of a moulded mass of sand dried at 105oC to 110oC is called DryPermeabilty. It is used for dried, baked or cured sand specimens.

    Test Procedure:

    1. Place split specimen tube on pedestal, and insert steel ring in bottom of tube.

    2. Tighten clamp on split specimen tube.3. Weigh out sufficient sand to produce a test specimen of standard dimensions, and ram

    according to standard procedure.

    4. Release clamp on specimen container, remove the tube, and place specimen on drier.

    The clamp is then release and the core is stripped.5. Place core in an oven and dry at 105oC to 110oC for one hour or until dry.

    6. Remove the specimen from oven, and place it in a desiccator to cool.

    7. When cool, place specimen in a core permeability tube. Clamp the specimen firmly inposition.

    8. Place permeability tube in position in permeability meter, and determine permeability

    in usual way, as described above.

  • 7/31/2019 F&F LAB MANUAL

    17/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    PRACTICAL # 10

    DETERMINATION OF A.F.S. CLAY CONTENTS IN THE GIVEN

    SAND SAMPLE USING SAND WASHER

    Overview:

    Sand testing washer is used for measuring the clay contents and sand contents of general

    moulding sand in percentage, and comprises 1 /20HP single phase motor (steplesslyadjustable between 600 and 3,000 rpm), vane shaft, beaker, siphon and timer.

    Equipment:

    A. Sand Testing washer

    B. Timer

    Chemicals / Materials:Testing sand, Caustic soda solution

    Operating Procedure:

    1. Dry the sand for one hour at 105 5oC.

    2. Then allow it to stand in a desiccator for cooling, and weigh 50 g of sampleaccurately , put into the beaker, add 475cc of 20 to 25oC distilled water and 25cc of

    caustic soda solution (with 30 g of caustic soda dissolved into 970 cc of water).

    3. Place the motor slowly on the beaker, and stir sufficiently for about 10 minutes.

    4. Take out the beaker, and pour water in it, to wash the sand adhering to the wall intothe beaker, up to about 15 cm depth in total.

    5. Stir it sufficiently, and allow it to stand for about 10 minutes and allow supernatant

    water to flow through siphon bringing the level down to 2.5 cm.6. Add 20 to 25oC distilled water again up to 15 cm depth, and stir sufficiently, and

    allow it to stand for about 10 minutes.

    7. Again allow the supernatant water to flow out by the siphon until the height from thebottom becomes 2.5 cm. Then, add water again up to 15 cm depth, stir it sufficiently

    and allow it to stand for 5-10 minutes.

    8. Repeat the same operation until the discharged water becomes clear.

    9. Filter the sand particles remaining in the beaker, using about 9 cm filter paper in aBuchner funnel, and move the sand along with filter paper to a large wash glass.

    10. Dry it perfectly at 105 5oC and cool in a desiccator.

    11. Double the difference between the weight of washed sand particles and the weight oforiginal sample is the percent of clay content.

  • 7/31/2019 F&F LAB MANUAL

    18/18

    WWW.07MET.TKCasting & Working of Metals Lab Manuals

    Remarks:

    1. If the distilled water is not available, ordinary water can be used.

    2. It is desirable that test should be conducted twice or more for the same sample, andthat the mathematical mean value of test results within deviation 5 % should be

    taken as the result of the test.3. The motor speed can be adjusted steplessly between 600 and 3,000 rpm, and therefore

    when it is desired to shorten the time or to change stirring eddy current, the speed can

    be adjusted arbitrarily (standard speed is 1,500 rpm for 50 Hz, and 1,800 rpm for 60

    Hz).