FD910 Density Meter

download FD910 Density Meter

of 2

Transcript of FD910 Density Meter

  • 7/27/2019 FD910 Density Meter

    1/2ISSUE: FD910/MAY2001/UK

    continuous on-line density measurement

    accuracy to 0.0001g/cm3 reading

    straight through flow

    smart headmount electronics option

    local display option

    insensitive to plant / pipeline vibration

    316L stainless steel wetted parts

    intrinsically safe and flameproof design

    wide operating temperature span

    options to suit extensive applications

    compact and lightweight design

    no on-site calibration required

    secondary containment

    Sarasota

    Industrial Density Meter

    FD910

    Features

    The Sarasota FD910 density meter is designed for highaccuracy measurement of general process liquids andslurries.

    Dimensional drawing

    Applications process control quality control productinterface detection process monitoring

    206.5mm

    530mm

    198mm

    128mm

    271mm

    89mm

    Detailed specification and ordering information: see overleafThermo Measurement reserves the right to alter specifications without notice.

  • 7/27/2019 FD910 Density Meter

    2/2

    Specification

    Thermo Electron CorporationKings Worthy

    Winchester, HampshireSO23 7QA, United Kingdom

    Tel: +44 (0) 1962 625000Fax: +44 (0) 1962 885530email: [email protected]

    Thermo Electron Corporation9303 W. Sam Houston Parkway South

    HoustonTexas77099 5298 USA

    Tel: +1 (713) 272 0404Fax: +1 (713) 272 2273

    Ordering Information

    Transducer:

    Operating range: 0 to 2.1g/cm3

    Factory calibration range: 0.65 to 1.6g/cm3

    Accuracy: 0.0001g/cm3

    Repeatability: 0.00002g/cm3

    Temperature effect:

    (corrected) see Note 1 0.000005g/cm3/C

    Process temperature: -50 to +180C

    Pressure effect:

    (corrected) see Note 1 0.000003g/cm3/bar

    Operat ing pressure: Flange pressure/temperature rating

    Materials of construction: Sensor/wetted material 316L stainless steel

    Case 316L stainless steel

    Electronics housing copper free

    aluminium grey epoxy finish

    Secondary containment: Full pipeline specification at 40 bar

    NACE MR0175 conformity: NACE specification option

    Temperature measurement: High accuracy 13 DIN

    Integral 4 wire PT100

    General:

    Environmental protection: IP65

    Hazardous area certification: FD910F EEx ia IIC T6

    FD910H EEx ia IIC T4

    EEx d IIC T4/T3

    Weight: Nett 11kg max

    Shipping 20kg max

    Installation: Vertical as standard

    Optionally horizontal

    Flow range: 0-300 l/min

    5-300 l/min when installed horizontally

    Outputs:

    F option: Frequency related to density on 2 wire current

    modulated loop 6mA to 18mA

    4 wire PT100

    H option: Analogue 4-20mA related to density or

    density derived variable

    HART protocol

    System: Accuracy better than 0.2% reading plus

    0.05% of span at reference conditions

    HART

    Local display option

    Electrical:

    Power supply:

    F option: 13-28 VDC 10mA average (peak 18mA)

    H option: 2 x 13-28 VDC 25mA

    Connections: Screw terminals

    Cable entry: 2 x 34 NPT

    Operating temperature(ambient): -20 to +70C

    Example: FD910-H-2-G-B0-I-L

    FD910 industrial density meter with smartheadmount electronics, 0.00025g/cm3,standard temperature range of -20 to +120C,ANSI Class 150 RF flanges, intrinsically safeapproval with local display.

    Density meter model code format

    FD910 Sarasota Industrial Density Meter

    Signal output

    F Frequency output

    H Smart headmount electronics

    Transducer accuracy

    2 0.00025g/cm3

    1 0.0001g/cm3

    Temperature range

    G -20 to +120C

    H -50 to +180C

    Process connections

    B0 1 ANSI B16.5 Class 150 RF flanges

    B1 1 ANSI B16.5 Class 150 Duplex flanges

    F0 1 ANSI B16.5 Class 300 RF flanges

    F1 1 ANSI B16.5 Class 300 Duplex flanges

    A0 1 ANSI B16.5 Class 600 RF flanges

    A1 1 ANSI B16.5 Class 600 Duplex flanges

    D BS4504 PN40 DN25 RF flanges (Form D)

    X Other flange type (see note)

    Certification

    S Non hazardous / safe area application

    I Intrinsically safe EEx ia IIC T4/T6

    D Flameproof EEx d IIC T4/T3

    Options

    L Local display (with FD910H only)

    M Wetted parts material certificates (DIN 50049 BS EN 10204 3.1b)

    N NACE conformance

    T Traceable calibration certificate

    Note: Where an X option is chosenthe option must be described fully,in writing. Please contact salesoffice for pricing.

    Note 1 - Corrected temperature and pressure effects after

    applying correction coefficients

    HART is a registered trademark of the Hart Foundation