FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain...

48
FASTENERS Screws, Nails, Bolts…

Transcript of FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain...

Page 1: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

FASTENERSScrews, Nails, Bolts…

Page 2: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS AND NAILS• Must resist corrosion

• Rusting fasteners retain moisture• Rot• Bleed

Page 3: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS AND NAILS• Galvanized coating

• Specify “hot-dipped”• Avoid electro-galvanized (bright)

• Stainless steel

• Polymer-coated

Page 4: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 5: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 6: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 7: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 8: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILS• Hardened piece of wire

• Nail length is given in “Penny Weight” (d)• 10d nail is about 3” long

Page 9: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

PENNYWEIGHT?The term penny originated in England

many years ago. Ten penny, four penny, etc., nails got their names from the fact that one hundred nails of that size cost ten pence, four pence, etc. Today penny represents the definite length of a nail measured from the head to the tip of the point. The term penny is still shown by using the English Pence sign d.

Page 10: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILSAvoid splitting wood

• Using pilot holes

• Flat side with the grain

Page 11: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILSAvoid splitting wood

• Stagger nails

Page 12: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILSAvoid splitting wood

• Blunt tips

Page 13: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILS TYPES• Smooth shank

• Ring shank

• Spiral shank

• Truss nail

• Duplex nail (temporary)

Page 14: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 15: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 16: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

NAILS TYPES

Page 17: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS• Greater resistance to withdrawal than nails

• Specify size by diameter and length• ¼” x 3”• ½” x 6”

Page 18: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

PILOT HOLE for SCREWS• Pilot hole should be smaller than screw

• Thread bites into wood

• Size of shank

Page 19: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS TYPESWood Screws

• Standard

• Phillips

• Square drive

• Star (torx) drive

Page 20: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

Screws• Phillips/Square/Slotted combo head

Page 21: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS TYPESSheet metal screws

• Tip acts like a drill bit

Page 22: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

SCREWS TYPESLag Screws

• Heavy duty screw used when bolts cannot

• 2 to 8” long

Page 23: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

Lag Screws Installation• Drill about half the length of lag screw

• Hammer to bottom of pilot hole

• Thread the rest of way

Page 25: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

BOLTS• Better shear strength than nails and screws• Used in major structural joints• Size: diameter and length• Sizing length: 1” greater than the adjoining

boards

Page 26: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

PILOT HOLE for BOLTS• Pilot hole same size as bolt

• Thread bite not required

• Washers and nut required to fasten

Page 27: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

BOLT TYPES

Standard Bolt• Hex or square head

Page 28: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

BOLT TYPES

Carriage bolt• Round head with square base for better look and

feel• Tighten until square base crunches in

Page 29: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 30: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• ThruLOK bolts• http://www.youtube.com/watch?v=ApIDd39L

UGc

Page 31: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

BOLT TYPES

Expanding or wedge bolt• Attaching to concrete or brick• Flange fits into pre-drilled hole

Page 32: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

Wedge Bolt Installation• Drill depth of bolt with concrete bit

• Hammer bolt to bottom of pilot hole• Avoid flattening threads

• Tighten nut and washer

Page 33: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

IPE Clips

Page 34: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

IPE Clips• https://www.youtube.com/watch?v=vJsfpp

0gt8M

Page 35: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

JOINING MATERIALS

Direct nailing: 1” from end and side

Page 36: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

JOINING MATERIALS

• Toenailing: 45-degree through end of board

Page 37: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

JOINING MATERIALS

• Butt joint: two boards simply butted together

Page 38: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• Miter cut: angle cut across width• Miter joint: 90-degree corner

JOINING MATERIALS

Page 39: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• Bevel cut: angle cut along thickness

JOINING MATERIALS

Page 40: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• Cross cut: cutting across the grain

at 90-degree

JOINING MATERIALS

Page 41: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• Rip cut: cutting with the grain

JOINING MATERIALS

Page 42: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

• Table saw for rip cuts• Table saw sensor• https://www.youtube.com/watch?v=No_h6iVI

FgA

Page 43: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

JOINING MATERIALS

• Splicing: overlap or gusset over beam

Page 44: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

CONNECTORS

Joist hanger: connecting joist to ledger

Page 45: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.
Page 46: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

CONNECTORS

• Post saddle: fastening beam to top of post

Page 47: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

CONNECTORS

• Angle bracket: support under wood (steps)

Page 48: FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

CONNECTORS

Rafter ties: connect joist to beam