FAS Track UL Assemblies - BuildSite...The Innovators of Quality Framing and Lath Systems CEMCO Deep...

FAS Track UL Assemblies

Section 1

Standard Wall Assemblies 1� Total Movement

HW-D-0514 � Perpendicular Fluted Deck with Fireproofing

HW-D-0514 � Perpendicular Fluted Deck with Fireproofing and Z-clip

HW-D-0514 � Parallel to Fluted Deck with Fireproofing and Z-clip

HW-D-0515 � Concrete Slab

HW-D-0518 � Perpendicular to Fluted Deck

HW-D-0518 � Perpendicular to Fluted Deck, 3 Hour Rating

HW-D-0524 � Parallel to Flute (FAS Strap)

HW-D-0550 � Gypsum Wallboard Ceiling

HW-D-0551 � Stairwell By-Pass at I-Beam

HW-D-0551 � Centered Directly Under Beam

HW-D-0551 � Off-Center Under Beam

HW-D-0553 � Chase Wall at Pan Deck

HW-D-0554 � Chase Wall at Concrete Slab

HW-D-0556 � Parallel to I-Beam

HW-D-0573 � Perpendicular I-Beam Penetration

HW-D-0596 � Head of Wall System at Stairwell Slab

HW-D-0600 � Cantilever Under Beam � Regular Wall

HW-D-0620 � Parallel Under Pan Deck

Section 2

Standard Wall Assemblies 2� Total Movement

HW-D-0576 � Chase Wall at Concrete Slab

HW-D-0577 � Perpendicular to Fluted Deck

HW-D-0578 � Gypsum Wallboard Ceiling

HW-D-0579 � Centered Directly Under Beam

HW-D-0580 � Chase Wall at Pan Deck

HW-D-0581 � Concrete Slab

HW-D-0582 � Parallel with Fluted Deck


HW-D-0587 � Parallel with Fluted Deck (FAS Strap)

HW-D-0601 � Parallel to I-Beam � Regular Wall and Z-Bar

Section 3

Shaft Wall Assemblies 1� Total Movement

HW-D-0557 � Concrete with Shaft-Wall

HW-D-0524 � Shaft Wall Parallel to Flute (FAS Strap)

HW-D-0525 � Fluted Deck Shaft-Wall

HW-D-0525 � Parallel to Fireproofed Fluted Deck Shaft-Wall

HW-D-0525 � Perpendicular to Fireproofed Fluted Deck Shaft-Wall

HW-D-0563 � Shaft-Wall Parallel to Beam

HW-D-0598 � Parallel Cantilever Under Shaft


HW-D-0622 � Shaft Wall under I-Beam

HW-D-0621 � Shaft Wall Slab By-Pass

Section 4

Shaft Wall Assemblies 2� Total Movement

HW-D-0584 � Shaft-Wall Fluted Deck, 2� Movement

HW-D-0585 � Shaft-Wall at Concrete Slab 2� Movement

HW-D-0586 � Shaft-Wall Parallel to Beam, 2� Movement

HW-D-0599 � Parallel Cantilever Under Shaft-Wall

HW-D-0587 � Shaft-Wall Parallel to Fluted Deck (FAS Strap)


HW-D-0622 � Shaft Wall under I-Beam

Section 5

FAS Track 500 ½� Total Movement

HW-D-0624 � Standard Wall to Concrete Deck

HW-D-0625 � Shaft Wall to Concrete Deck

Section6

Vertical Wall Assembly

WW-S-0057 �Standard Wall Vertical Wall Tie-in to Concrete Column

WW-S-0061 Shaft Wall Vertical Wall Tie-in to Concrete Column

Section 7

Bottom of Wall

BW-S-0024 � Bottom Track static joint

Section 8

Specification Sheets

Contact Product Manager Don Pilz for any technical support at [email protected] or

(626) 506-3881.

mailto:[email protected]�

Section 1 STANDARD WALL ASSEMBLIES

1� TOTAL MOVEMENT

For all technical support, contact Don Pilz at [email protected] or 626-506-3881


Section 2 STANDARD WALL ASSEMBLIES

2� TOTAL MOVEMENT



Section 3 SHAFT-WALL ASSEMBLIES

1� TOTAL MOVEMENT



Section 4 SHAFT-WALL ASSEMBLIES

2� TOTAL MOVEMENT



Section 5 FAS-TRACK 500 ASSEMBLIES

1/2� TOTAL MOVEMENT



Section 6 VERTICAL WALL ASSEMBLIES



Section 7 BOTTOM OF WALL ASSEMBLY



Section 8 SPECIFICATION SHEETS



The Innovators of Quality Framing and Lath Systems

CEMCO FAS Track Specification Sheet

Patent No. US 7, 617, 643 B2

Track Member Width

Length

Gauge (mils)

2 ½”, 3 5/8”, 4”, 6”, and 8”

10’ 0” 20, 18, 16, and 14 GA (33, 43, 54, and 68 mil)

Drift slots on the web are optional. CEMCO FAS Track is a slotted deflection track that offers fire and air (smoke) protection. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 and 18 gauges (33 and 43 mils) with a minimum G40 coating complying with ASTM A924; and Grade 50 Type H for 50 ksi yield strength steel for 16 and 14 gauges (54 and 68 mils) with a minimum G60 coating complying with ASTM A924. The FAS Track is designed with Blazeseal intumescent fire rated tape on both site of the FAS Track. The FAS Track is listed under Underwriters Laboratories for one and two hour head of wall fire rated wall assemblies.

CALIFORNIA EXPANDED METAL LATH PRODUCTS CO.

Corporate Office: 263 N. Covina Lane, 1001-A Pittsburg Antioch Hwy, 490 Osage Street, City of Industry, CA 91744 Pittsburg, CA 94565 Denver, CO 80204 Phone (800) 775-2362 Phone (925) 473-9340 Phone (303) 572-3626 Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO Deep Leg FAS Track Specification

Patent No. US 7, 617, 643 B2 Track Member Width

Length

Gauge (mils)

2 ½”, 3 5/8”, 4”, 6”, and 8”

10’ 0” 20, 18, 16, and 14 GA (33, 43, 54, and 68 mil)

CEMCO Deep Leg FAS Track is a deflection track that offers fire and air(smoke) protection. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 and 18 gauges (33 and 43 mils) with a minimum G40 coating complying with ASTM A924; and Grade 50 Type H for 50 ksi yield strength steel for 16 and 14 gauges (54 and 68 mils) with a minimum G60 coating complying with ASTM A924. The Deep Leg FAS Track is designed with Blazeseal intumescent fire rated tape on both site of the Deep Leg FAS Track. The Deep Leg FAS Track is listed under Underwriters Laboratories for one and two hour head of wall fire rated wall assemblies.

CALIFORNIA EXPANDED METAL LATH PRODUCTS CO. Corporate Office: 263 N. Covina Lane, 1001-A Pittsburg Antioch Hwy, 490 Osage Street, City of Industry, CA 91744 Pittsburg, CA 94565 Denver, CO 80204 Phone (800) 775-2362 Phone (925) 473-9340 Phone (303) 572-3626 Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO FAS SHAFT TRACK Specification

Patent No. US 7, 617, 643 B2

Track Member Width (A)

Length

Gauge (mils)

2 ½”, 4” and 6”

10’ 0” 20 GA (33mil)

Drift slots on the web are optional. Vertical Slots on the Flange are optional for positive attachment. CEMCO FAS SHAFT TRACK is a slotted deflection track that offers fire and air (smoke) protection in shaft wall assemblies. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 gauge (33 mils) with a minimum G40 coating complying with ASTM A924. The FAS SHAFT TRACK is designed with factory applied intumescent fire rated tape on non shaft side of the FAS SHAFT TRACK. The FAS SHAFT TRACK is listed under Underwriters Laboratories for one and two hour head of wall fire rated wall assemblies.

CALIFORNIA EXPANDED METAL LATH PRODUCTS CO.

Corporate Office: 263 N. Covina Lane, 1001-A Pittsburg Antioch Hwy, 490 Osage Street, City of Industry, CA 91744 Pittsburg, CA 94565 Denver, CO 80204 Phone (800) 775-2362 Phone (925) 473-9340 Phone (303) 572-3626 Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO FAS Shaft Track DL2 Specification Sheet

Patent No. US 7, 617, 643 B2

Track Member Width

Length

Gauge (mils)

2 ½”, 4”, and 6” 10’ 0” 20 GA (33mil)

Drift slots on the web are optional.

CEMCO FAS Shaft Track DL2 is a deep leg deflection track that offers fire and air (smoke) protection for shaft wall assemblies. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Structural Grade 50 Type H for 50 ksi yield strength steel and Grade 33 Type H 33 ksi yield strength steel with a minimum G40 coating. The FAS Shaft Track DL2 is manufactured with Blazeseal intumescent fire rated tape on the top portion of the leg wrapping the corner onto the back web of the track on one side only. The FAS Shaft Track DL2 is listed under Underwriters Laboratories for one and two hour rated head of wall assemblies.

CALIFORNIA EXPANDED METAL LATH PRODUCTS CO. Corporate Office: 263 N. Covina Lane, 1001-A Pittsburg Antioch Hwy, 490 Osage Street, City of Industry, CA 91744 Pittsburg, CA 94565 Denver, CO 80204 Phone (800) 775-2362 Phone (925) 473-9340 Phone (303) 572-3626 Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO FAS Track 500 Specification Sheet

Track Member Width

(A)

Length

Gauge

(mils)

(G) 2 ½”, 3 5/8”, 4”, 6”, and 8”

10’ 0” 20, 18, 16, and 14 GA

(33, 43, 54, and 68 mil) Drift slots on the web are optional.

CEMCO FAS Track 500 is a deflection track that offers fire and air (smoke) protection. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 and 18 gauges (33 and 43 mils) with a minimum G40 coating complying with ASTM A924; and Grade 50 Type H for 50 ksi yield strength steel for 16 and 14 gauges (54 and 68 mils) with a minimum G60 coating complying with ASTM A924. The CEMCO FAS Track 500 is designed with a ½” Blazeseal intumescent fire rated tape on both side of the FAS Track 500.

CALIFORNIA EXPANDED METAL LATH PRODUCTS CO. Corporate Office:

263 N. Covina Lane, 1001-A Pittsburg Antioch Hwy, 490 Osage Street,

City of Industry, CA 91744 Pittsburg, CA 94565 Denver, CO 80204

Phone (800) 775-2362 Phone (925) 473-9340 Phone (303) 572-3626

Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO FAS Shaft Track 500 Specification Sheet

Patent No. US 7, 617, 643 B2

Track Member Width

(A)

Length

Gauge

(mils)

2 ½”, 4”, and 6” 10’ 0” 20 GA

(33mil)


CEMCO FAS Shaft Track 500 is a deflection track that offers fire and air (smoke) protection for shaft wall assemblies. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Structural Grade 50 Type H for 50 ksi yield strength steel and Grade 33 Type H 33 ksi yield strength steel with a minimum G40 coating. The FAS Shaft Track 500 is manufactured with a ½” Blazeseal intumescent fire rated tape on applied on non shaft side of the FAS Shaft Track 500.





Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com


CEMCO FAS Track DL 500 Specification Sheet

Track Member Width

(A)

Length

Gauge

(mils)

(G) 2 ½”, 3 5/8”, 4”, 6”, and 8”

10’ 0” 20, 18, 16, and 14 GA

(33, 43, 54, and 68 mil)


CEMCO FAS Track DL 500 is a deep leg deflection track that offers fire and air (smoke) protection. The section is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 and 18 gauges (33 and 43 mils) with a minimum G40 coating complying with ASTM A924; and Grade 50 Type H for 50 ksi yield strength steel for 16 and 14 gauges (54 and 68 mils) with a minimum G60 coating complying with ASTM A924. The FAS Track DL 500 is manufactured with a ½” Blazeseal intumescent fire rated tape on the top portion of the leg wrapping the corner onto the back web of the track.





Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627 www.cemcosteel.com


CEMCO FAS STRAP Specification

PATENT PENDING

Member Width

Length

Gauge

(mils) 10 ½ ”

10’ 0” 20, 18,16 and 14

(33, 43, 54, and 68)

CEMCO FAS STRAP is a flat strap with 2 strips of ½” intumescent. This strap is fabricated from hot-dipped galvanized steel complying with ASTM A653, and ASTM A1003 Grade 33 Type H for 33 ksi yield strength steel for 20 and 18 gauges (33 and 43 mils) with a minimum G40 coating complying with ASTM A924; and Grade 50 Type H for 50 ksi yield strength steel for 16 and 14 gauges (54 and 68 mils) with a minimum G60 coating complying with ASTM A924. The FAS STRAP is listed under Underwriters Laboratories for one and two hour head of wall fire rated wall assemblies.





Fax (626) 330-7598 Fax (925) 473-9341 Fax (303) 572-3627

www.cemcosteel.com

FAS TRACK’S ENVIRONMENTAL BENEFITS AND LEED CONTRIBUTIONS

FAS Track™ represents an environmental advancement for interior partition construction. Its resilient intumescent layer of Blaze Seal makes it a one-piece solution to acoustical and ire resistive head assemblies. FAS Track’s partition head assembly eliminates most bridging, elastomeric sealants, mineral wool, and the need to cut drywall to it the lutes of decking. FAS Track reduces scraps and waste and often does not require any sealant to be applied to the head of wall joint. Resources are saved, and indoor air quality is improved.

FAS Track contributes to a number of LEED credits in the 2009 New Construction, Core and Shell, Commercial Interiors, and Schools rating systems.

RESOURCE CONSERVATION: Because even very short pieces of FAS Track are used in construction, very little is wasted. Scraps as small as 16 inches are often retained. The metal portion of smaller scraps can be recycled, once the BlazeSeal is peeled off by hand. For projects with high targets for MR 2 Construction Waste Management, this method of recycling FAS Track scraps will contribute to this credit.

MR CREDIT 4 RECYCLED CONTENT: Like all of CEMCO’s framing products, FAS Track contributes 32.7% recycled content to this credit.

IEQ 3.2 INDOOR AIR QUALITY MANAGEMENT PLAN – BEFORE OCCUPANCY: If the Air Testing option is selected by the project team, FAS Track is a valuable player in achieving this credit. FAS Track eliminates the need for spray-applied smoke seal and elastomeric ire sealant. It also can take the place of acoustical sealant in some assemblies. With no solvents and very low VOC content, FAS Track signiicantly reduces indoor air pollution. The Air Testing option is dificult to achieve, and every bit of indoor pollution that FAS Track eliminates from the project increases the chances of success. IEQ 4.1 LOW-EMITTING MATERIALS – ADHESIVES AND SEALANTS:FAS Track’s intumescent ire-resistive seal is a solid, factory-applied layer, so it is not required to comply with the Adhesives and Sealants VOC limits. Moreover, because BlazeSeal provides all the ire protection required for many partitions, no spray-applied smoke seals or elastomeric ire-resistive sealants are required, so their VOC contributions are eliminated.

IEQ 4.6 LOW-EMITTING MATERIALS – CEILING AND WALL SYSTEMS (LEED FOR SCHOOLS): This credit does not apply to FAS Track. Only the gypsum board and the wall coverings are required to be tested.

IEQ 9 ENHANCED ACOUSTICAL PERFORMANCE (LEED FOR SCHOOLS): FAS Track improves the Sound Transmission Class (STC) of partitions, and can even eliminate the need for acoustical sealant at the head of partitions. Its resilient BlazeSeal layer helps damp sound transmission of partitions around core learning spaces and can help achieve this credit.

For other LEED credit contributions, see HYPERLINK “http://www.cemcosteel.com” www.cemcosteel.com and click “LEED Certiication”.

If you have any questions, concerns, or clariications, please contact our Technical Services Department at (800) 416-2278 or HYPERLINK “http://www.cemcosteel.com” www.cemcosteel.com.

Corporate Headquarters &

Main Manufacturing Facility

263 North Covina Lane

City of Industry, CA 91744

800.775.2362 Phone

626.330.7598 Fax

Northern California

Manufacturing Facility

1001-A Pittsburg Antioch Hwy

Pittsburg, CA 94565

925.473.9340 Phone

925.473.9341 Fax

Denver Colorado

Manufacturing Facility

490 Osage Street

Denver, CO 80204

303.572.3626 Phone

303.572.3627 Fax

Printed on 50% recycled

25% post–consumer waste

8 0 0 . 7 7 5 . 2 3 6 2

WWW.CEMCOSTEEL.COM

CEMCO925-473-9340Customer Servicewww.cemcosteel.com

Marino\Ware219-378-7100Mike Fenbertwww.marinoware.com

Marino\Ware800-504-8199Bill Maynewww.marinoware.com

Marino\Ware800-627-8199Gerry Comptonwww.marinoware.com





FAS Track UL Assemblies - BuildSite...The Innovators of Quality Framing and Lath Systems CEMCO Deep...

Documents

Transcript of FAS Track UL Assemblies - BuildSite...The Innovators of Quality Framing and Lath Systems CEMCO Deep...