LOCATION OF THE CAR ALARM CONTROL UNIT

Compact control units and sirens: place under the bonnet on the driver’s side in front of the battery. Modular control units and accessories: place under the dashboard on the driver’s side.

--------------------------------------------------------------------------------------------------------------------------------------------- CAR ALARM SUPPLY

Positive: Connect to the Red/White wire (pos. n° 15) in the 16-pin connector XS6 in the Black central unit located under the dashboard driver’s side.

Negative: Connect to the Brown wire (pos. n°10) in the lights commutator on the dashboard driver’s side or to a predisposition it originates them.

---------------------------------------------------------------------------------------------------------------------------------------------

IMMOBILIZER Starter motor: Cut the Red/Black wire directly at the ignition key unit.

--------------------------------------------------------------------------------------------------------------------------------------------- POSITIVE IGNITION KEY (+15)

Connect to the Black wire (pos. n°12) on the Light Brown 18-pin XS4 connector in the Black central unit located under the dashboard driver’s side.

--------------------------------------------------------------------------------------------------------------------------------------------- CENTRAL DOOR LOCKING (Connection with RF remote controlled alarm)

Negative Control. Connect to the Blue/Yellow wire (pos. n°6) in the connector located in exiting from driver’s side door: connect the the

exiting wire (with connector a 180 ohm resistor in series) e closing of alarm directly to the wire indicated without carring cut.

-------------------------------------------------------------------------------------------------------------------------------------------- ARMING OF PASSIVE TYPE ALARM (Connection with alarm armed by vehicle’s original remote control)

Follow the method of connections in INSTALLATION FILE 36.13.2 --------------------------------------------------------------------------------------------------------------------------------------------

DIRECTION INDICATORS

Connect to the Black/White (pos. n°16), Black/Green wire (pos. n°14) located on the Black 16-pin XS6 connector in the Black central unit located on the dashboard driver’s side.

ONLY TOP CAN ALARM Control of Blinker (negative control) : connect to the White/Green wire (Pos. n° 6) on the Black 12-pin XS1

connector in the Black central unit located on the dashboard driver’s side. Feedback : Connect to the Black/Green wire (pos. n°14) located on the Black 16-pin XS6 connector in the Black

central unit located under the dashboard driver’s side. ---------------------------------------------------------------------------------------------------------------------------------------------

DOOR PROTECTION Connect to the Purple/Red (pos. n°6 ant. Sx), Yellow/Green (pos. n°4 ant. Dx), Black/Green (pos. n°13 post. Dx),

White/Green (pos. n°3 post. Sx)wires on the light Brown 18-pin connector marked XS4 in the Black central unit located under the dashboard driver’s side.

Follow the methods of connections in INSTALLATION FILE 36.13.1 If you fit the dedicated alarm, the door and boot switches are normally detected by the CAN line.

--------------------------------------------------------------------------------------------------------------------------------------------- BONNET/BOOT PROTECTION

Bonnet: Fit the switch provided. Boot: connect to the Green/Orange wire (pos. n°3) in the Red 6-pin connector marked XS5 in the Black central unit

located under the dashboard driver’s side.

Follow the method of connections in INSTALLATION FILE 36.13.1 If you fit the dedicated alarm, the door and boot switches are normally detected by the CAN line.

--------------------------------------------------------------------------------------------------------------------------------------------------- CLAXON

Connect to the Black/Yellow wire(pos. n°2)in the 18-pin connector marked XS4 in the Black central unit located under the dashboard driver’s side.

18/06/2007 rev. The information brought back on this card are from considering themselves indicative and to take place itself before executing every connection in how much the constructor puo, ' anytime, introducing modifications. In any case the MetaSystem declines every responsibility for eventual damages brings you to the car from a wrong assembly.

CarAlarm TIPO DI AUTOVETTURA E ANNO DI PRODUZIONE

SKODA FABIA 2007

SCHEDA NUMERO

36.13

Fit diodes on the vehicle’s original wires as shown above. For positions, refer to installation file. 18/06/2007 rev. The information brought back on this card are from considering themselves indicative and to take place itself before executing every connection in how much the constructor puo, ‘ anytime, introducing modifications. In any case the MetaSystem declines every responsibility for eventual damages brings you to the car from a wrong assembly.

CarAlarm TIOP DI AUTOVETTURA E ANNO DI PRODUZIONE

SKODA FABIA 2007

SCHEDA NUMERO

36.13.1

WIRING DIAGRAM FOR DOOR/BOOT PROTECTION (for radio frequency remote controlled alarms only)

MAIN CONTROL UNIT

Connect to

wire from alarm for

protection of doors

Front left

Rear left

Rear right

BOOT

Connect to wire from

alarm for protection of boot

ATTENTION: Make sure the ignition key has been taken out of the ignition before connecting up the alarm control unit’s connector.

This setting is made by turning the vehicle’s ignition key to the “KEY ON” position and keeping it there for 20 seconds.

After 20 seconds, turn the ignition key back to the “KEY OFF” position and complete the final check.

IF THE AUTOMATIC RECOGNITION PROCEDURE IS NOT SUCCESSFUL, DO THE SETTING MANUALLY WITH

SELECTION “A READ THE FITTING INSTRUCTIONS SUPPLIED WITH THE PRODUCT IN THE SECTION ON VEHICLE CAN RECOGNITION OR USE THE CAR ALARM PROGRAMMER

Function Colour Alarm Cable Colour Car Cable Positioning car

Linea CAN H Black/Red Orange/Green Pos 12

Linea CAN L Black/Purple Orange/Brown Pos 9

BLACK 18-pin connector

marked XS2 at the Black central unit located under

the dashboard driver’s side.

Black Local plant placed under the dushboard in the side of drive

18/06/2007 rev. The information brought back on this card are from considering themselves indicative and to take place itself before executing every connection in how much the constructor puo, ' anytime, introducing modifications. In any case the MetaSystem declines every responsibility for eventual damages brings you to the car from a wrong assembly.

CarAlarm TIPO DI AUTOVETTURA E ANNO DI PRODUZIONE

SKODA FABIA 2007

SCHEDA NUMERO

36.13.2

METHOD OF INSTALLATION FOR VW CAN ALARM