Ez Strip TR Muncher
-
Upload
domczepiga -
Category
Documents
-
view
165 -
download
5
Transcript of Ez Strip TR Muncher
EZstrip™
TR Muncher®
Pull out cutter stack cartridge allows removal without disturbing pipeline or electrical connection.
Grinder ChallengeTraditional grinder maintenance requires full removal from the pipe work to replace the grinder's cutters, spacers, and shafts. This job is strained by reduced maintenance budgets and diminishing in-house expertise.
EZ SolutionThe EZstrip™ series of grinders offer a competitive solution to solids grinding and sludge conditioning. The EZstrip™ TR Munchers® include the quick access port allowing the cutter stack assembly to be maintained-in-place reducing maintenance time from an entire day to just a few hours.
• Reduces the time and effort required for maintenance
• Eases removal of rotating parts without disconnecting the electrical connection to the unit
• Eliminates the need for removing housing from the pipe work
• No special tools required
Maintain-in-Place Capabilities
Angled cutter stack "upflow" design rejects hard materials reducing the risk of damage to the cutter teeth.
Built-in trash trap is situated below and away from the cutter stack to catch any rejected
material. Rejected items can be removed or flushed out through the clean out port.
Service ExchangePre-assembled cartridge is
available with a 2-year warranty to allow faster reassembly time
Energy Efficient MotorsEfficient motors along with low
installation power to further reduce operating costs
Low Running SpeedsReduced wear for longer working
life and extended periods between routine maintenance
Eliminate Dismantling Space During Maintenance
Suction and discharge ports remain connected to pipe work
Cartridge AssemblyShort lead times for cutter stack
cartridge replacement units
Cantilever design eliminates the need for lower mechanical seals or bearings reducing breakdowns and repair costs.
ETOS (Equal Thrust Offset) cutters capture and reduce large solids for effective maceration.
Side-mounted CT201 applicable for smaller flow
rates.
Assumptions: Labor cost per hour is $60, grinder type is CT203 (6"), flow rate is 400 gpm, pump life is 15 years, maintenance inspection is 30 minutes once a year, maintenance intervention is 2.5 hours every two years, and inflation rate of 3%
Time and Cost Savings
EZstrip™ TR Muncher® provides a quick and easy answer to maintain your grinder in place, reducing maintenance time by more than 70% for significant cost savings.
You'll save more than $4,700* over the life of one EZstrip™ TR Muncher® compared to a standard grinder.
To see the EZstrip™ TR Muncher® in action, visit www.EZstrip.com.
$0
$1,000
$2,000
$3,000
$4,000
$5,000
$6,000
$7,000
$8,000
$9,000
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
EZstripTM TR Muncher® Standard Grinder
Number of Years
Mai
nten
ance
Co
st O
ver
Pum
p L
ife ($
)
EZstripTM TR Muncher®
reduces grinder maintenance time from ten and half hours
to three hours.
Maintenance Time
121110
9
87 6 5
4
3
21
CT203 & CT205 Dimensions
CT203 & CT205 Performance Data
All dimensions are in inches and for guidance only. For full certified drawings or assistance in selecting a pump, visit www.monoflo.com.
MODEL HP A B C D E F G H I J K L M N O LBS.
CT203P
2.0
3.94 14.57 40.15 8.07 0.94 19.25 16.14 4.88 5.51 14.17 14.29 0.31 0.71 7.09 8.66 639
CT203Q 5.90 14.57 40.15 9.06 0.98 21.26 16.14 6.10 1.57 14.17 13.94 0.31 0.87 9.45 11.22 639
CT203R 7.87 14.57 40.15 10.08 1.14 23.27 16.14 8.07 0.63 14.17 13.82 0.47 0.87 11.61 13.50 639
CT205S 9.84 14.57 46.85 11.06 1.26 27.24 18.11 8.07 1.18 16.14 19.45 0.47 1.02 13.98 15.98 760
CT205T 11.81 14.57 46.85 13.07 1.26 31.26 18.11 10.35 -0.67 16.14 18.58 0.47 1.02 16.14 19.01 760
CT203P
3.0 - 5.0
3.94 15.55 44.49 8.07 0.94 19.25 16.14 4.88 6.65 14.75 14.29 0.31 0.71 7.09 8.66 749
CT203Q 5.90 15.55 46.06 9.06 0.98 21.26 16.14 6.10 3.82 14.17 13.94 0.31 0.87 9.45 11.22 749
CT203R 7.87 15.55 46.06 10.08 1.14 23.27 16.14 8.07 2.83 14.17 13.82 0.47 0.87 11.61 13.50 749
CT205S 9.84 15.55 51.57 11.06 1.26 27.24 18.11 8.07 3.43 16.14 19.45 0.47 1.02 13.98 15.98 860
CT205T 11.81 15.55 51.57 13.07 1.26 31.26 18.11 10.35 1.57 16.14 18.58 0.47 1.02 16.14 19.01 860
A
B
C
4-HOLES Ø18
'L' HOLES Ø'M'ON A 'N' PCD
10.63
12.60
21.34
0.98
0.79
J
G H
F
D
E
I
O
K
0.98
0 100 200 300 400 500 600 700 800 900 1,100 1,2001,000Capactiy (US GPM)
0.00
1.00
2.00
3.00
4.00
5.00
6.00
7.00
Pres
sure
Diff
(PSI
)
8% DS 6% DS 4% DS 2% DS 0% DS10% DSCT203R
(8”)
CT203Q(6”)
CT203P(4”)
2.0 HP
3.0 HP
5.0 HP
CT2032.0 HP
3.0 HP
5.0 HP
0 500 1,000 1,500 2,000 2,500Capactiy (US GPM)
0.00
1.00
2.00
3.00
4.00
5.00
6.00
7.00
Pres
sure
Diff
(PSI
)
8% DS 6% DS 4% DS 2% DS 0% DS10% DS
CT205T(12”)
CT205S(10”) CT205
Published information other than marked CERTIFIED does not extend any warranty or representation, expressed or implied, regarding these products. Any such warranties or other terms and conditions of sales and products shall be in accordance with NOV Monoflo’s standard terms and conditions of sale available for request.
NOV Monoflo® products are marketed outside North America under the trademark NOV Mono®.
Literature reference: EZP-R1 2011
NOV Monoflo® is a registered trademark of Mono Pumps Ltd. www.monoflo.com
United States of AmericaHouston, Texas +1 281 200 1200 [email protected]
ArgentinaBuenos Aires +54 11 4290 9940/50 [email protected]
CanadaLloydminster, Alberta +1 780 875 5504 [email protected]
FranceRebeuville, Lorraine +33 (0)3 29 94 26 88 [email protected]
New Zealand Auckland +64 (0)9 829 0333 [email protected]
United KingdomManchester, England +44 (0)161 339 9000 [email protected]
China Shanghai +86 (0)21 3990 4588 [email protected]
Australia Melbourne, Victoria 1 (800) 333 138 [email protected]
CT201 Performance Data
CT201 Dimensions
0.00
0.72
1.45
2.17
2.90
3.62
4.35
5.07
0 88 176 264 352 440 528 616
2.0 HP
3.0 HP
8% DS 6% DS 4% DS 2% DS 0% DS
Capactiy (US GPM)
Pres
sure
Diff
(PSI
)
8 HOLES TAPM16 x 20 DEEP
EQUI-SPACED ONA 240 PCD
(OPPOSITE FLANGEIDENTICAL)
4 HOLES DRILLØ 18 THRO'
B
A
C
D
1.02 1.02
10.24
11.81
13.07
0.79
8.46
8.27
0.7911.81
10.24
5.91
MODEL HP A B C D LBS.
CT201Q 2.0 27.55 7.32 15.78 27.55 308
CT201Q 3.0 28.15 7.99 16.93 28.74 385
All dimensions are in inches and for guidance only. For full certified
drawings or assistance in selecting a pump, visit www.monoflo.com.