EZ Ladder Part #: EZ - 25 A 2 A 2 B 1 Specify Ladder ... › Content › Images...EZ SERIES FIXED...
6
Patent Pending EZ SERIES FIXED ACCESS LADDERS ATTACH MOUNTING BRACKETS 1 PLACE RUNG IN BRACKET 2 SECURE WITH BOLT- ON CAPTURE PLATE 3 Installs in three easy steps Engineered from the ground up for OSHA 1910.23 COMPLIANCE
Transcript of EZ Ladder Part #: EZ - 25 A 2 A 2 B 1 Specify Ladder ... › Content › Images...EZ SERIES FIXED...
Patent Pending
EZ SERIES FIXED ACCESS LADDERS ORDERING INFORMATION
24400 Sperry Drive • Cleveland, OH 44145440-348-9460
Represented By:
EZ Ladder Part #: EZ - 25 A 2 A 2 B 1
TerminationA = Pass ThroughB = Side Step
Return Accessory1 = P Style2 = Guardrail Style
Parapet Crossover KitA = NoneB = Yes
Vertical Lifeline1 = None2 = Yes
Ladder GuardA = NoneB = Yes
Swing Gate1 = None2 = Swing Gate
Specify Ladder Length
05 = 5’
06 = 6’
07 - 7’08 = 8’
09 = 0’
10 = 10’
11 = 11’
12 = 12’
13 = 13’
14 = 14’
15 = 15’
16 = 16’
17 = 17’
18 = 18’
19 = 19’
20 = 20’
21 = 21’
22 = 22’
23 = 23’
24 = 24’
25 = 25’
26 = 26’
27 = 27’
28 = 28’
29 = 29’
30 = 30’
Additional Sizes available upon request
Swing Gate Ladder Guard Vertical Lifeline Parapet Crossover Kit
Part Number: EZ 25-A-2-A-2-B-1
Part Description: 25-foot ladder with pass-through termination, guardrail-style return, NO parapet crossover, vertical lifeline, ladder guard and NO swing gate.
ORDER EXAMPLE
EZ Ladder System Accessories:
Patent PendingEZ SERIES FIXED ACCESS LADDERS
ATTACH MOUNTING BRACKETS1 PLACE RUNG
IN BRACKET2 SECURE WITH BOLT-ON CAPTURE PLATE3
Installs in three easy steps
Engineered from the ground up for
OSHA 1910.23 COMPLIANCE
Faster, Safer Climbs
• The widest rail to rail and terminal pass-through dimensions in the industry provide safe access and easily accomodates vertical lifeline installation.
• Flat stock side rails for secure hand holds.
• Grooved rungs for enhanced traction.
Built for the Long Haul• Carbon steel with standard hot dipped galvanized finish outlasts powder coated ladders.
• The only fixed ladder with a limited lifetime warranty.
• Made in the USA
Patent Pending
THE FASTEST INSTALLING - EASIEST CLIMBING -LONGEST LASTING - FIXED ACCESS LADDER SYSTEM
Diversified Fall Protection24400 Sperry Drive • Cleveland, OH 44145
www.fallprotect.comRev. 12-2018
Patent Pending
EZ SERIES FIXED ACCESS LADDERS ORDERING INFORMATION
24400 Sperry Drive • Cleveland, OH 44145440-348-9460
Represented By:
EZ Ladder Part #: EZ - 25 A 2 A 2 B 1
TerminationA = Pass ThroughB = Side Step
Return Accessory1 = P Style2 = Guardrail Style
Parapet Crossover KitA = NoneB = Yes
Vertical Lifeline1 = None2 = Yes
Ladder GuardA = NoneB = Yes
Swing Gate1 = None2 = Swing Gate
Specify Ladder Length
05 = 5’
06 = 6’
07 - 7’08 = 8’
09 = 0’
10 = 10’
11 = 11’
12 = 12’
13 = 13’
14 = 14’
15 = 15’
16 = 16’
17 = 17’
18 = 18’
19 = 19’
20 = 20’
21 = 21’
22 = 22’
23 = 23’
24 = 24’
25 = 25’
26 = 26’
27 = 27’
28 = 28’
29 = 29’
30 = 30’
Additional Sizes available upon request
Swing Gate Ladder Guard Vertical Lifeline Parapet Crossover Kit
Part Number: EZ 25-A-2-A-2-B-1
Part Description: 25-foot ladder with pass-through termination, guardrail-style return, NO parapet crossover, vertical lifeline, ladder guard and NO swing gate.
ORDER EXAMPLE
EZ Ladder System Accessories:
Patent PendingEZ SERIES FIXED ACCESS LADDERS
ATTACH MOUNTING BRACKETS1 PLACE RUNG
IN BRACKET2 SECURE WITH BOLT-ON CAPTURE PLATE3
Installs in three easy steps
Engineered from the ground up for
OSHA 1910.23 COMPLIANCE
Faster, Safer Climbs
• The widest rail to rail and terminal pass-through dimensions in the industry provide safe access and easily accomodates vertical lifeline installation.
• Flat stock side rails for secure hand holds.
• Grooved rungs for enhanced traction.
Built for the Long Haul• Carbon steel with standard hot dipped galvanized finish outlasts powder coated ladders.
• The only fixed ladder with a limited lifetime warranty.
• Made in the USA
Patent Pending
THE FASTEST INSTALLING - EASIEST CLIMBING -LONGEST LASTING - FIXED ACCESS LADDER SYSTEM
Diversified Fall Protection24400 Sperry Drive • Cleveland, OH 44145
www.fallprotect.comRev. 12-2018
OSHA compliance requires fixed ladders to have a minimum of 7" of clear distance from the ladder rungs' center line to the building INCLUDING ANY PERMANENT OBSTRUCTIONS. (Measurement B, figure 1)
Common obstructions to consider when ordering and installing ladders include:
1. Roof or gutter overhang2. Pipe or conduit3. Parapet walls
How to Measure for Proper Ladder Length• Pass Through Applications: Measure from the point at which the climber steps off to within 14 inches of lower surface (Measurement A, figure 1).• Parapet Wall Applications: Measure both top of parapet wall to within 14 inches of lower level AND top of parapet wall to roof surface as two ladders are typically required. (Measurement A and C, figure 2) Specify the Universal Parapet Cross Over Kit when ordering.• Side Step Applications: Measure from the point where the climber steps off the ladder to within 14 inches of lower level PLUS 48 inches (Measurement A, figure 3).
1
2
Pass Through Fig. 1
3
Parapet Cross Over Fig. 2
4Side Step Fig. 3
MEASURING FOR LADDER LENGTH AND STAND-OFF DISTANCE
The (required) extension above the top access level must be at least 24 inches wide (to accomodate the width of climber's body). The extension can be no more than 30 inches wide, (36 inches if a ladder
lifeline is provided) allowing the climber to easily reach both hand rails.
Per OSHA 1920.23 (d) (5)
42”
To protect the worker exiting a ladder, OSHA requires a 42-inch high grab bar extension above the access level or landing platform at the
top of the ladder.
Per OSHA 1910.23 (d) (4)
24”
Climbing width: must be a minimum of 16 inches. Per OSHA 1910.23 (b) (4)
7”
A stand-off distance of 7 inches.7 inches minimum must be measured from the mid-point
of the ladder rung to the nearest permanent object in back of the ladder. Be sure to allow safe clearance
including any permanent obstructions in your calculation.
Per OSHA 1910.23 (d) (2)
16”
24 Feet The following measurements all related to fixed (permanently mounted) access ladders that reach 24 feet or more above a lower level.
5 IMPORTANT MEASUREMENTS FOR OSHA - COMPLIANT FIXED ACCESS LADDERS Patent Pending
BETTER LADDERS BY DESIGN
• Stand-off brackets adjust from 7-1/2” to 14” to work around obstructions and ensure OSHA compliance.
• Engineered side rails allow for precise placement of bolt-on stand-off brackets, eliminating the need for field modifications.
EZ Series Ladders reduce installation times by 50%
16”
24”
Permanently Welded
No
2“ x 2” Angle
Powder Coated
Over Length LTL SurchargesApply
Competing Brands
20”
30”
Bolt On, With Vertical/HorizontalAdjustability
Yes
3” Flat Stock
Hot Dipped Galvanized
10’ Max Modular Sections Reduce Freight Costs
EZ Series Ladders
Rung Width
Walk Through
Stand Off Brackets
Floor/Bottom Mount
Side Rail Construction
Standard Finish
Freight Costs
Features
OSHA compliance requires fixed ladders to have a minimum of 7" of clear distance from the ladder rungs' center line to the building INCLUDING ANY PERMANENT OBSTRUCTIONS. (Measurement B, figure 1)
Common obstructions to consider when ordering and installing ladders include:
1. Roof or gutter overhang2. Pipe or conduit3. Parapet walls
How to Measure for Proper Ladder Length• Pass Through Applications: Measure from the point at which the climber steps off to within 14 inches of lower surface (Measurement A, figure 1).• Parapet Wall Applications: Measure both top of parapet wall to within 14 inches of lower level AND top of parapet wall to roof surface as two ladders are typically required. (Measurement A and C, figure 2) Specify the Universal Parapet Cross Over Kit when ordering.• Side Step Applications: Measure from the point where the climber steps off the ladder to within 14 inches of lower level PLUS 48 inches (Measurement A, figure 3).
1
2
Pass Through Fig. 1
3
Parapet Cross Over Fig. 2
4Side Step Fig. 3
MEASURING FOR LADDER LENGTH AND STAND-OFF DISTANCE
The (required) extension above the top access level must be at least 24 inches wide (to accomodate the width of climber's body). The extension can be no more than 30 inches wide, (36 inches if a ladder
lifeline is provided) allowing the climber to easily reach both hand rails.
Per OSHA 1920.23 (d) (5)
42”
To protect the worker exiting a ladder, OSHA requires a 42-inch high grab bar extension above the access level or landing platform at the
top of the ladder.
Per OSHA 1910.23 (d) (4)
24”
Climbing width: must be a minimum of 16 inches. Per OSHA 1910.23 (b) (4)
7”
A stand-off distance of 7 inches.7 inches minimum must be measured from the mid-point
of the ladder rung to the nearest permanent object in back of the ladder. Be sure to allow safe clearance
including any permanent obstructions in your calculation.
Per OSHA 1910.23 (d) (2)
16”
24 Feet The following measurements all related to fixed (permanently mounted) access ladders that reach 24 feet or more above a lower level.
5 IMPORTANT MEASUREMENTS FOR OSHA - COMPLIANT FIXED ACCESS LADDERS Patent Pending
BETTER LADDERS BY DESIGN
• Stand-off brackets adjust from 7-1/2” to 14” to work around obstructions and ensure OSHA compliance.
• Engineered side rails allow for precise placement of bolt-on stand-off brackets, eliminating the need for field modifications.
EZ Series Ladders reduce installation times by 50%
16”
24”
Permanently Welded
No
2“ x 2” Angle
Powder Coated
Over Length LTL SurchargesApply
Competing Brands
20”
30”
Bolt On, With Vertical/HorizontalAdjustability
Yes
3” Flat Stock
Hot Dipped Galvanized
10’ Max Modular Sections Reduce Freight Costs
EZ Series Ladders
Rung Width
Walk Through
Stand Off Brackets
Floor/Bottom Mount
Side Rail Construction
Standard Finish
Freight Costs
Features
OSHA compliance requires fixed ladders to have a minimum of 7" of clear distance from the ladder rungs' center line to the building INCLUDING ANY PERMANENT OBSTRUCTIONS. (Measurement B, figure 1)
Common obstructions to consider when ordering and installing ladders include:
1. Roof or gutter overhang2. Pipe or conduit3. Parapet walls
How to Measure for Proper Ladder Length• Pass Through Applications: Measure from the point at which the climber steps off to within 14 inches of lower surface (Measurement A, figure 1).• Parapet Wall Applications: Measure both top of parapet wall to within 14 inches of lower level AND top of parapet wall to roof surface as two ladders are typically required. (Measurement A and C, figure 2) Specify the Universal Parapet Cross Over Kit when ordering.• Side Step Applications: Measure from the point where the climber steps off the ladder to within 14 inches of lower level PLUS 48 inches (Measurement A, figure 3).
1
2
Pass Through Fig. 1
3
Parapet Cross Over Fig. 2
4Side Step Fig. 3
MEASURING FOR LADDER LENGTH AND STAND-OFF DISTANCE
The (required) extension above the top access level must be at least 24 inches wide (to accomodate the width of climber's body). The extension can be no more than 30 inches wide, (36 inches if a ladder
lifeline is provided) allowing the climber to easily reach both hand rails.
Per OSHA 1920.23 (d) (5)
42”
To protect the worker exiting a ladder, OSHA requires a 42-inch high grab bar extension above the access level or landing platform at the
top of the ladder.
Per OSHA 1910.23 (d) (4)
24”
Climbing width: must be a minimum of 16 inches. Per OSHA 1910.23 (b) (4)
7”
A stand-off distance of 7 inches.7 inches minimum must be measured from the mid-point
of the ladder rung to the nearest permanent object in back of the ladder. Be sure to allow safe clearance
including any permanent obstructions in your calculation.
Per OSHA 1910.23 (d) (2)
16”
24 Feet The following measurements all related to fixed (permanently mounted) access ladders that reach 24 feet or more above a lower level.
5 IMPORTANT MEASUREMENTS FOR OSHA - COMPLIANT FIXED ACCESS LADDERS Patent Pending
BETTER LADDERS BY DESIGN
• Stand-off brackets adjust from 7-1/2” to 14” to work around obstructions and ensure OSHA compliance.
• Engineered side rails allow for precise placement of bolt-on stand-off brackets, eliminating the need for field modifications.
EZ Series Ladders reduce installation times by 50%
16”
24”
Permanently Welded
No
2“ x 2” Angle
Powder Coated
Over Length LTL SurchargesApply
Competing Brands
20”
30”
Bolt On, With Vertical/HorizontalAdjustability
Yes
3” Flat Stock
Hot Dipped Galvanized
10’ Max Modular Sections Reduce Freight Costs
EZ Series Ladders
Rung Width
Walk Through
Stand Off Brackets
Floor/Bottom Mount
Side Rail Construction
Standard Finish
Freight Costs
Features
Patent Pending
EZ SERIES FIXED ACCESS LADDERS ORDERING INFORMATION
24400 Sperry Drive • Cleveland, OH 44145440-348-9460
Represented By:
EZ Ladder Part #: EZ - 25 A 2 A 2 B 1
TerminationA = Pass ThroughB = Side Step
Return Accessory1 = P Style2 = Guardrail Style
Parapet Crossover KitA = NoneB = Yes
Vertical Lifeline1 = None2 = Yes
Ladder GuardA = NoneB = Yes
Swing Gate1 = None2 = Swing Gate
Specify Ladder Length
05 = 5’
06 = 6’
07 - 7’08 = 8’
09 = 0’
10 = 10’
11 = 11’
12 = 12’
13 = 13’
14 = 14’
15 = 15’
16 = 16’
17 = 17’
18 = 18’
19 = 19’
20 = 20’
21 = 21’
22 = 22’
23 = 23’
24 = 24’
25 = 25’
26 = 26’
27 = 27’
28 = 28’
29 = 29’
30 = 30’
Additional Sizes available upon request
Swing Gate Ladder Guard Vertical Lifeline Parapet Crossover Kit
Part Number: EZ 25-A-2-A-2-B-1
Part Description: 25-foot ladder with pass-through termination, guardrail-style return, NO parapet crossover, vertical lifeline, ladder guard and NO swing gate.
ORDER EXAMPLE
EZ Ladder System Accessories:
Patent PendingEZ SERIES FIXED ACCESS LADDERS
ATTACH MOUNTING BRACKETS1 PLACE RUNG
IN BRACKET2 SECURE WITH BOLT-ON CAPTURE PLATE3
Installs in three easy steps
Engineered from the ground up for
OSHA 1910.23 COMPLIANCE
Faster, Safer Climbs
• The widest rail to rail and terminal pass-through dimensions in the industry provide safe access and easily accomodates vertical lifeline installation.
• Flat stock side rails for secure hand holds.
• Grooved rungs for enhanced traction.
Built for the Long Haul• Carbon steel with standard hot dipped galvanized finish outlasts powder coated ladders.
• The only fixed ladder with a limited lifetime warranty.
• Made in the USA
Patent Pending
THE FASTEST INSTALLING - EASIEST CLIMBING -LONGEST LASTING - FIXED ACCESS LADDER SYSTEM
Diversified Fall Protection24400 Sperry Drive • Cleveland, OH 44145
www.fallprotect.comRev. 12-2018
