EZ-212 User Manual

Easy Wire 230Volt Smoke

Alarm

1

CONTENTS

PageIntroduction 2

Sensor technology 2

Application 3

Positioning 6

Limitations 7

How to install your FireAngel1. Preparation 102. Install mounting plate 103. Connect wiring 114. Fit your FireAngel 145. Fully charge your FireAngel 156. Test your FireAngel 15

OperationLow battery condition 17Alarm test 18Alarm silence 20Routine maintenance 22Removal 23

What to do in case of fire in your home 24

Repair 25

Troubleshooting 25

Disposal 27

How to make your home safer 27

Warranty 29

Returns 30

2

IntroductionCongratulations! You've made a wise investment in an innovative product andyour personal safety. The FireAngel is one of a new generation of domesticlife safety products from FireAngel Limited, which combines the latesttechnology and innovative design to provide an aesthetically pleasing andeffective contribution to your fire safety.

The FireAngel range of products is constantly being improved and expanded.Please visit www.FireAngel.co.uk to find out about the latest additions to ourproduct range.

IMPORTANT: This user manual contains important informationregarding the operation of your FireAngel Smoke Alarm. If you areinstalling this smoke alarm for use by others, you must leave thismanual (or a copy of it) with the end user.

Sensor TechnologyYour FireAngel Smoke Alarm uses an ionisation type sensor to detect thepresence of smoke. Ionisation type smoke alarms are generally more effectiveat detecting fast, flaming fires which consume combustible materials rapidlyand spread fire quickly. To increase the level of protection you should alsoinstall optical (photoelectric) type smoke alarms that are more effective atdetecting slow burning fires, which can smoulder for hours before burstinginto flames.

For Maximum protection, use both types of smoke alarms on eachlevel of your home

3

FireAngel ApplicationWARNING: If your FireAngel smoke alarm is being installed into anew build property then the new building regulations apply. You canobtain further information from your local fire service/building controlat your local council offices. These sources generally provide advice onnew builds or projects that require planning permission.

WARNING: To comply with building regulations, and therecommendation of the UK fire services, there should be a minimumof one smoke alarm on each level of your property.

Your FireAngel Smoke Alarm will communicate with other alarms of the sametype if their ‘interconnect’ wires are connected together. This means that inthe event of smoke being detected by one unit, all other connected units willalso go into full alarm.

4

The FireAngel typically meets the minimum requirements for family living unitsin new and existing buildings, as long as at least one unit is installed on eachfloor/level of your property.

In order to achieve the earliest fire warning, we recommend that a FireAngelis fitted in all rooms where the temperature is normally between 40°F (4ºC)and 100°F (30ºC). The type of smoke alarm used in each location should beappropriate to the environment. Check the section on ‘Positioning’ to ensurethat the FireAngel is to be correctly positioned for the particular dwelling intowhich it is intended to be installed.

The alarm positions shown above are based on typical homes.Construction and layout of individual dwellings will vary, so thisshould be regarded only as a guide. Check with your local firestation for further guidance.

Lounge

Cellar

BedroomBedroom Hall

Dining Room

KitchenHall

Dining Room

Lounge

Bedroom

Lounge

Cellar

BedroomBedroom

Dining Room

Lounge Kitchen

Dining RoomBedroom

HallHall

Minimum recommendations

Recommended foradditional protection

Minimum requirements

Recommended foradditional protection

Interconnection betweensmoke alarms

Existing Homes

New Construction

NOTE: Please refer to BS5839 part 6 for further information.

5

Multi-Family or Mixed Occupant Residence (Tenancy Building, Studentaccommodation)

The FireAngel can also be used in individual flats and bedsits, providing thesame conditions are met as for a single-family residence. However, there mustalready exist a primary fire detection system that meets regulatoryrequirements for common areas such as lobbies and hallways.

Institutions and Hotels

This includes motels, hospitals, day care facilities, long-term health carefacilities, boarding houses and dormitories.

The FireAngel can be used in individual sleeping/resident rooms, providing thesame conditions are met as for a single-family residence. However, there mustalready exist a primary fire detection system that meets regulatoryrequirements for common areas such as lobbies and hallways. Use of theFireAngel in common areas may not provide sufficient fire warning toresidents or meet regulatory requirements.

The FireAngel is designed to operate as a standalone smoke alarm, or can beconnected to other compatible FireAngel alarms (up to a maximum of 12alarms where the total interconnected length is less than 200m).

The FireAngel product range is continuously evolving so it is recommendedthat you call the technical support line for more information and advice onrange compatibility. Tel: +44 (0) 24 7623 6663

WARNING: The FireAngel will not communicate with other types ofsmoke alarm or fire alarm systems. It is not intended as a substitutefor a complete alarm system.

Mobile Homes and Caravans

The FireAngel is not intended for use in Mobile homes and Caravans.

Commercial and Industrial Premises

The FireAngel is not intended for any non-residential, commercial or industrialapplication, nor for any other purpose than described above.

5

6

PositioningIt is recommended that your FireAngel is NOT to be fitted in the followinglocations.

• Bathrooms, shower-rooms, areas close by, and other very damp or humidareas, where the moisture can cause unwanted alarms.

• Kitchens and air streams near kitchens. Kitchens should be protected withself-contained Heat Alarms, as the combustion particles from cooking inkitchens will result in unwanted alarms and permanent contamination ifSmoke Alarms are used.

• Areas where combustion particles may be present such as garages andboiler rooms. These areas should be well ventilated.

• In areas where excessive dust or dirt could contaminate the sensingchamber, making it over sensitive or impairing smoke entry.

• In areas where the ambient temperature is not controlled and mayregularly drift below 4°C (40°F) or above 38°C (100°F) e.g. unheatedbuildings, open attic spaces.

• Very dirty, dusty or greasy areas.

• In very draughty areas, such as close to ceiling fans or fresh air vents.Draughts can blow smoke away from the alarm.

• In insect infested areas. Insects can clog openings to the sensing chamber,preventing smoke entry or causing unwanted alarms.

• Within 30cm (12") of a fluorescent light fitting, which emits electrical‘noise’ that can prevent correct alarm operation.

• In wall positions that are more than 30cm (12") away from the ceiling (see‘How to install your FireAngel’).

• In 'dead air' spaces (see following diagram).

• Within 30cm (12") of light fittings or other ceiling based obstructions.

7

What are the limitations of mySmoke Alarm?

Your FireAngel is designed to alert you by sounding an alarm when it sensessmoke, i.e. it can only sense smoke and alert you if smoke reaches it! If a firedevelops in an area remote from the location of the FireAngel such as anotherroom or another level, smoke may not reach the FireAngel in sufficient time orquantity to sense and alert you to the danger. (We recommend that as aminimum you install a FireAngel on every floor of your property whereregulatory requirements permit, and consider fitting additional units in otherareas where a smoke alarm is not generally considered essential.)

1 metre(3 feet)

100mm(4 inches)

100mm(4 inches)

Best location(in centre of ceiling)Dead

air spaces

8

Up to 12 FireAngels can be interconnected. The maximum length of theinterconnect wire must be less than 200m. If a larger number of alarms areinterconnected, the presence of smoke in one alarm may not becommunicated to the others.

The FireAngel cannot be used to provide primary fire detection in commonareas used by different residents such as blocks of flats and hotels.

The FireAngel may not alarm before a fire causes damage, injury or death, asthe smoke may not reach the FireAngel in time. Examples include smoking inbed and violent gas explosions. The FireAngel may not respond in areasonable time if it is not installed in the best position, or if furniture or otherobstacles are located between the FireAngel and the fire.

The FireAngel requires an ac electrical supply for its normal operation and torecharge its integral battery. If the electrical supply fails or is removed the unitwill continue to operate on its fully charged battery supply for 45 days. TheFireAngel will advise you of a low battery condition by emitting an audible'chirp' once per minute. When this occurs you must restore the electricitysupply to the unit within 7 days to maintain operation and recharge theinternal battery. The supply must be turned on for at least 4 hours to give aminimum of 7 days charge. To fully recharge your FireAngel to enable 45 daysoperation the supply must be turned on for a further 8 hours.

Smoke Alarms are designed to alert you with an audible alarm at a levelspecified by BS 5446 part 1 - 2000. Closed doors, walls and high ambientnoise levels will reduce this level. Temporary or permanently impaired hearingmay result in the alarm not being heard. Stereos, traffic and other loudsources may also prevent the alarm being heard. Heavy sleepers and residentsunder the influence of alcohol or drugs may also not hear or respond to thealarm. Test and check that you can hear the alarm in all circumstances. If indoubt install additional smoke alarms as required, which should beinterconnected if possible.

WARNING: The FireAngel is not suitable for alerting hearing impairedresidents. We recommend that specially designed warning systems beinstalled that will alert hearing impaired residents.

IMPORTANT INFORMATION

8

9

WARNING: The FireAngel employs the latest technology and is LPCBcertified as being compliant with all the relevant British Standards.However, as with any electronic product it may fail and may notsense all types of fire within sufficient time to alert you of the dangerand provide adequate time for your escape. In order to maximise yourlevel of safety always test your FireAngel frequently to ensure it is infull working order.

Your FireAngel is only suitable for use in domestic/residential applications ascovered in this manual. It is not suitable for commercial or industrialapplications. It is designed to sense smoke and alert you. It will not sensecarbon monoxide, flames, heat or gas. It will not prevent or extinguish fires.

The FireAngel has a limited life and should not be considered as a substitutefor life or property insurance. Like all electronic equipment, it can wear out orfail. It should be tested weekly and replaced immediately in the event offailure, and replaced every ten years regardless.

IMPORTANT: This product should be installed in accordance with thecurrent edition of the IEE Wiring Regulations, if in doubt contact aqualified electrician.

10

How to install your FireAngelIMPORTANT: Make sure you have read and understood thismanual before installing your FireAngel.

IMPORTANT: Before starting the installation ensure that theelectricity supply has been isolated at the power distributionboard/consumer unit. Switching the light off at the light switchwill NOT isolate the power.

WARNING: Failure to turn off the power before installation mayresult in serious electrical shock, injury or death.

1. PreparationCarefully make access through the ceiling or wall toallow the passage of the wires and any terminals andconnector boxes that are to be fitted.

Use the mounting plate as a guide when marking thearea that is required for access. If mounting on a wallensure mounting holes are vertical.

2. Install Mounting PlateFit the FireAngel mounting plate to the ceiling or wall.

If the FireAngel is to be installed on a wall, ensure thatthe mounting plate is the correct way round (arrowpointing upwards).

IMPORTANT: The mounting plate must be securely mounted to asuitable load-bearing surface.

WARNING: Exposed and vulnerable wires present a risk of fireand electric shock. All wires and connections must beadequately insulated and protected.

11

3. Connect wiringThis product meets the requirements of the LPCB approval to BS5446-1:2000only when installed with a permanent live feed

Consumer InformationBS5446-1: 2000 makes provision for either permanently powered mains alarmsor battery powered alarms. The innovative ‘hybrid’ nature of this FireAngelmakes it possible to operate the smoke alarm from a switch live feed. Atpresent the British standard contains no requirements for this mode ofoperation and because of this the LPCB approval can only apply to thisFireAngel when wired to a permanent live feed.

The FireAngel can be wired in a number of different ways to suit your specialrequirements. You have the following choices:

a) Standard - Permanent connection to the permanent live and also theswitched live from the light switch. This is the recommended method, as theinternal battery will be kept fully charged. You can test or reset your FireAngelby flicking a light switch within the circuit you have installed the alarm or byusing the test/reset button on the alarm itself. See diagram on page 12.

b) Switched – Power taken from a switched light fitting. This method can beused if it is not convenient to access a permanent live supply wire. The sameTest and reset features are available, but the light fitting must be used for atleast 2 hours a week to ensure the internal battery is charged. See diagram onpage 13.

c) Limited – Permanent battery charging connection only. This has theadvantage of keeping the internal battery fully charged under normalconditions, but does not allow the FireAngel to be tested or reset using a lightswitch; the test/reset button on the alarm must be used for this purpose.Please follow the wiring diagram on page 12, however, the connection to theswitched live is not made in this configuration. This configuration is usedmostly where switched live of a nearby lighting circuit is unavailable henceany secure permanent live connection can be used.

NOTE: On all wiring configurations the white interconnect wire neednot be connected if the alarms are not required to communicate witheach other.

IMPORTANT: If the interconnect function is not used then alarmsWILL NOT communicate with each other (detection of smoke in onealarm will NOT force others into alarm).

12

To PreviousFireAngel

To NextFireAngel

Connector /Junction Box

Light Switch,Dimmer or

Dual switch control

FireAngel

To Power Distribution Board220/240 Volts AC 50 Hz.

Mains Supply protected by acircuit breaker or fuse and

fitted with an isolating switchin accordance with

wiring regulations (BS7671in England and Wales).

House wiring must be earthedin accordance with regulations

(BS7671 in England and Wales).There is no earth connectionnecessary for the FireAngel,however, a spare terminal isprovided for the earth wire.

Earth connectionsnot illustrated

LN

LN

L

SW

N

Standard wiring schematic

Ceiling rose /Junction box

See enlarged schematic below for wiring details

New FireAngel installationExisting wiring

LSW N

Fly-lead Connector

I/C

L Live SupplySW Switched LiveI/C InterconnectN Neutral

COLOUR KEY

Switched Live

13

To PreviousFireAngel

To NextFireAngel

Light Switch,Dimmer or

Dual switch control

FireAngel

To Power Distribution Board220/240 Volts AC 50 Hz.

Mains Supply protected by acircuit breaker or fuse and

fitted with an isolating switchin accordance with

wiring regulations (BS7671in England and Wales).

House wiring must be earthedin accordance with regulations

(BS7671 in England and Wales).There is no earth connectionnecessary for the FireAngel,however, a spare terminal isprovided for the earth wire.

Earth connectionsnot illustrated

LN

LN

L

SW

N

Switched wiring schematic

Ceiling rose /Junction box

See enlarged schematic below for wiring details

New FireAngel installationExisting wiring

LSW N

Fly-lead Connector

I/C

L Live SupplySW Switched LiveI/C InterconnectN Neutral

COLOUR KEY

Switched Live

Connector /Junction Box

NOTE - Connect L & SWin Connector Box

Connector /Junction Box

14

NOTE: All wire connections not used must be capped with anappropriate insulated terminal.

NOTE: Where the switched live is used to charge the battery(Switched option), only connect to light fittings that are usedregularly. Your FireAngel requires the light to be turned on forapproximately 2 hours (minimum) per week to remain in its fullycharged state. This can be achieved with a single period of 2 hours ormany periods of a few minutes totalling 2 hours.

WARNING: The FireAngel is intended for operation only on 220-250V AC, 50Hz.

IMPORTANT: Where FireAngels are interconnected, do not connectany more than 12 together in a single circuit.

4. Fit your FireAngel

b) Removeshipping disabletag.Note: the alarmmay soundbriefly.If other alarmsare already wiredin, they may gointo full alarmuntil the shippingdisable isremoved.

a) Attachconnector plug toconnector pins onthe back of theFireAngel. Notethat theconnector canonly be fitted oneway. Ensure thatthe plug is heldsecurely by theclip on theFireAngel.

c) Position theFireAngel over themounting platelining up arrowsand turnclockwise tosecure in place.Your FireAngel willbe locked inposition. For removal seepage 23.

PUSH THREETIMES

-

TO SILENCE

TOTEST

-PUSH

TWICE

MAINS

-

FUNCTION-

d) Ensure thatthe FireAngel issecurely locatedinto its mountingplate, around itsentirecircumference.

15

CAUTION: The horn is designed to be loud to wake you in anemergency. Avoid placing your ear close to the alarm when installing it.

The FireAngel should show that it has been activated by a flashing red lightnext to the test button, approximately once a minute.

5. Fully charge your FireAngelTo ensure both the correct operation and maximum life span of your FireAngelit is necessary to fully charge the integral battery on installation. At the powerdistribution board/consumer unit, restore power to the electrical circuit whereyou installed the FireAngel. In the ‘limited’ wiring option it is necessary toleave the light switched on initially for at least 12 hours.

With the light switched on (Switched wiring option)or the electrical power connected (Standard orLimited wiring options), a green constant lightshould come on next to the test button.

6. Test your FireAngel Test Button Operation (All wiring options)

a) Press the test buttonon your FireAngel,twice.

b) Your FireAngel willgive out an audible(85db at 3m) test signalfor approximately 10seconds.

c) The red light on yourFireAngel will flash onceper second at the sametime as the audiblesignal.

PU

SHTH

REE TIMES -

- PUSH TWICE

TOSI

LENCE

TO TEST

MAINS -

PU

SHTH

REE TIMES -

- PUSH TWICE

TOSI

LENCE

TO TEST

MAINS -

16

Light Switch Operation (Standard and Switched wiring options)

IMPORTANTIf your FireAngel EZ-212fails to give an audibletest signal, please referimmediately to thetroubleshooting guideon page 25, 26 of thismanual. If your

NOTE: If the FireAngel begins to chirp once per minute, then you haveflicked the light switch or test button too many times and it hasentered into its automatic reset cycle. In this case wait for 15 minutesand then test again. If your FireAngel still fails to give an audible testsignal refer to the troubleshooting guide on pages 25, 26.

Note: Suitable for use with dimmer switches.

e) Ensure the lightswitch connected toyour FireAngel is turnedoff.

f) Flick the light switchon, then off, twice(quickly).

g) Your FireAngel willgive out an audible testsignal (85db at 3m) forapproximately 10seconds.

h) The red light on yourFireAngel will flash onceper second at the sametime as the audible signal.

PU

SHTH

REE TIMES -

- PUSH TWICE

TOSI

LENCE

TO TEST

MAINS -

i) All other interconnected FireAngels will giveout an audible test signal at the same time asthe unit being tested. The red lights on theseother units will not flash at the same rate, butonly once per minute.

d) All other interconnected FireAngels will giveout an audible test signal at the same time asthe unit being tested. The red lights on theseother units will not flash at the same rate, butonly once per minute.

17

Operation

Low Battery Condition

IMPORTANT: Your FireAngel requires an ac electrical supply torecharge its integral battery. Where the Standard and Limited wiringoptions are used, the battery will be maintained in a fully chargedstate as long as the electrical supply and connections are reliable. For Switched wiring option, only connect to light fittings that areused regularly; your FireAngel requires the light to be turned on inthis case for a total of approximately 2 hours per week (minimum) to remain in its fully charged state.

If the light is not used or the ac electrical supply is removed your FireAngelwill continue to operate in ‘standby’ (waiting for smoke) on its fully chargedbattery supply for 45 days.

Should your FireAngel enter a low battery condition, the unit will emit anaudible 'chirp' once per minute. When this occurs you must restore theelectricity supply to the unit to maintain operation. The green light next to thetest button should be on continuously when the electricity supply isconnected.

Following restoration of the mains supply the FireAngel batteries will rechargeto full capacity from a low battery alarm condition within 12 hours.

IMPORTANT: The Failsafe design of your FireAngel means that failureto restore the electrical supply may result in the FireAngel eventuallyentering a full alarm condition. Should this situation occur yourFireAngel would require a full 12 hour recharge before correct futureoperation is restored.

18

Alarm Test

WARNING: Test your FireAngel at least once per week.

Your FireAngel can be tested in one of two ways, depending on how it isinstalled. Either can be used to check the correct operation of the alarm.

Light Switch Operation (Standard and Switched wiring options)

Note: Suitable for use with dimmer switches.

PU

SHTH

REE TIMES -

- PUSH TWICE

TOSI

LENCE

TO TEST

MAINS -

e) All other interconnected FireAngels will giveout an audible test signal at the same time as theunit being tested. The red lights on these otherunits will not flash at the same rate, but onlyonce per minute.

a) Ensure the lightswitch is off.

b) Switch the light on,then off, twice in rapidsuccession (2 flicks).

c) Your FireAngel willemit an audible testsignal (85db at 3m) forapproximately 10seconds.

d) The red light on yourFireAngel will flash onceper second at the sametime as the audiblesignal.

19

Test Button Operation (All wiring options)

CAUTION: The horn is designed to be loud to wake you in anemergency. If you are very close to the alarm when it is sounding, itmay harm your hearing. Stand back from the alarm when testing.

WARNING: NEVER use an open flame to test your FireAngel. Thebuilt in test feature accurately tests your FireAngel's operation asrequired by the relevant British Standard (BS5446 Part 1 - 2000).

WARNING: Do not use aerosol smoke to test your FireAngel. Aerosolcontaminants can clog your FireAngel and prevent smoke fromreaching the sensor in a fire emergency.

a) Press the test buttonon the alarm twice inrapid succession.

b) Your FireAngel willemit an audible testsignal (85db at 3m) forapproximately 10seconds.

c) The red light on yourFireAngel will flash onceper second at the sametime as the audiblesignal.

PU

SHTH

REE TIMES -

- PUSH TWICE

TOSI

LENCE

TO TEST

MAINS -

d) All other interconnected FireAngels will giveout an audible test signal at the same time asthe unit being tested. The red lights on theseother units will not flash at the same rate, butonly once per minute.

20

Alarm Silence

DANGER: If your FireAngel alarms and you are not testing the unit,your FireAngel is warning you of a potentially dangerous situation thatrequires your immediate attention. Only use the alarm silence functionafter making sure that there is no ongoing fire emergency situation.Do not block the vents on the alarm or disable the FireAngel in anyway, as this will remove your protection.

In the event of a false alarm your FireAngel can be silenced in one of twoways, depending on how it is installed. Either can be used to silence the alarm.

Light Switch Operation (Standard and Switched wiring options)

Note: Suitable for use with dimmer switches.

a) Ensure the light switch is off.

b) Switch the light on, then off, threetimes in rapid succession.

d) During the reduced sensitivityreset cycle, your FireAngel will emitan audible 'chirp' once per minute.

c) Your FireAngel will silence andenter into a 15-minute (maximum)reduced sensitivity reset cycle.

e) Your FireAngel will automaticallyreturn to full sensitivity oncompletion of the reset cycle.

x3

a. b. c. d. e.

Test Button Operation (All wiring options)

NOTE: During strong thunderstorms and interruptions to your mainssupply your FireAngel may enter the alarm reset cycle.

IMPORTANT: (Switched wiring option only): If your FireAngelcontinues to 'chirp' after completion of the reset cycle, it is notifyingyou of a low battery condition. In this case leave the light turned onfor approximately 12 hours to fully recharge the integral battery.

DANGER: Never ignore any alarm. Ignoring the alarm may result ininjury or death. If your FireAngel alarms and you are not absolutelycertain of the source of the smoke, get everyone out of the houseimmediately.

NOTE: If the Standard or Switched wiring options are used, theFireAngel will count the combined number of light switch and testbutton operations. For example, if the light switch is flicked on andoff once then the test button pressed twice, all in quick succession,the FireAngel will identify this as a ‘silence’ signal and go into lowsensitivity mode.

a) Press the test button on the alarmthree times in rapid succession.

b) Your FireAngel will silence andenter into a 15-minute (maximum)reduced sensitivity reset cycle.

c) During the reduced sensitivityreset cycle, your FireAngel will emitan audible 'chirp' once per minute.

d) Your FireAngel will automaticallyreturn to full sensitivity oncompletion of the reset cycle.

21

22

Routine Maintenance

Your FireAngel has been designed to be as maintenance-free as possible andalthough the unit requires NO battery maintenance for its entire life, there areseveral things you must do to keep it working properly.

CAUTION: Your FireAngel is a sealed ac electrical device and noattempt should be made to open the case. Attempting to open thecase will invalidate your Warranty.

Testing

Test your FireAngel once per week see section ‘Alarm Test’ (pages 18 -19).

Cleaning

As a minimum your FireAngel should be cleaned once every 3 months usingyour vacuum cleaner fitted with the soft brush attachment.

WARNING: Your FireAngel may false alarm when it is being cleanedusing a vacuum cleaner.

IMPORTANT: Do not use solvents or cleaners on your FireAngel, asthey may cause damage. The unit can be wiped with a slightly dampcloth, but the electrical power at the power distributionboard/consumer unit MUST be turned off when this is done.

CAUTION: Do not paint the FireAngel as this may clog the openingsand prevent smoke being sensed.

a) Using the soft brush attachment of yourvacuum cleaner gently remove all signs of dustfrom the cover and ventilation holes.

b) Test to ensure correct operationsee section ‘Alarm Test’ (pages 18 -19)

23

Removal

WARNING: Your FireAngel will not alert you to smoke when it hasbeen removed or disabled.

WARNING: 230V wires will be exposed when removing theFireAngel. Ensure that all electrical power has been disconnectedbefore removing the FireAngel.

IMPORTANT: Do not remove the connector by pulling on the wires.This can damage the wire and may cause a fire or electrical safetyhazard.

Do not re-use the connector/cable assembly in a different location. If theFireAngel is to be re-installed in a different location, use a new assembly (partreference Z-099).

a) Push in tab on theside of the FireAngelindicated by the arrowon the mounting plateand simultaneouslyrotate the FireAngelanti-clockwise.

b) Pull the connectorclip to one side torelease the connector.Then pull theconnector from theFireAngel using the tabprovided.

c) Unscrew themounting plate fromthe ceiling.

SEE INSTRUCTIO

N

MANUAL

1

2

PO

INT

ARR

OW

UPW

ARDS

WHEN

ALIG

NAR

ROW

STO

MOUNT & ROTATE ALARM CLOCKWISE

WAL

L MOUNTING

What to do in case of fire inyour home

If you have made a family escape plan and practiced it with your family, youhave increased their chances of escaping safely. Go over the following ruleswith your children each time you have fire drills. This will help everyoneremember them in case of a real emergency.

• Don't panic; stay calm. Your safe escape may depend on thinking clearlyand remembering what you have practiced.

• Notify every member in the residence of the fire.

• Get out of the house as quickly as possible. Follow a planned escaperoute. Do not stop to collect anything or to get dressed.

• Feel the doors to see if they are hot. If they are hot, do not open them -use an alternative escape route.

• Stay close to the floor. Smoke and hot gases rise.

• Cover your nose and mouth with a cloth (wet if possible). Take short,shallow breaths.

• Keep doors and windows closed. Open them only if you have to in orderto escape.

• Meet at your planned meeting place after leaving the house. Carry out aheadcount.

• Call the Fire brigade on 999 as soon as possible from outside your house- it’s free! If possible use a neighbours phone or call box rather than amobile phone (as the location can be traced from the number if the line islost).

• Give the address and your name.

• Never go back inside the building until a member of the fire service hastold you it is safe to do so.

Contact your local Fire Brigade. They will give you more ideas about how tomake your home safer from fires and how to plan your family's escape.

24

25

RepairDO NOT attempt to repair your FireAngel, doing so will invalidate yourwarranty.

If your FireAngel is not operating properly, see 'TroubleShooting'.

If you cannot solve the problem, please call the Technical Support Linedetailed on page 30 for advice.

If your FireAngel is no longer under warranty, replace immediately with acomparable FireAngel brand Smoke Alarm.

CAUTION: Your FireAngel is a sealed ac electrical device and noattempt should be made to open the case. Attempting to open thecase will invalidate your Warranty.

TroubleShootingPROBLEM

FireAngel alarms whenno smoke is visible

SOLUTION

DANGER: If your FireAngels are interconnected,they may be warning you of a real fire hazard bydetecting smoke in a different area of your residence.If you are not absolutely certain of the source of thesmoke, get everyone out of the house immediately.

If your FireAngels are interconnected, identify which unit iscausing the alarm. This is indicated by the red light flashing onceper second. If none of the FireAngels are causing the alarm,switch off electrical power and check the interconnect wiring.Switch off electrical power to the FireAngel. Remove build-up ofstatic electricity by wiping your FireAngel with a slightly dampcloth.Clean your FireAngel (see Routine maintenance page 22).Check the location of your FireAngel (see Positioning page 6).Fully charge Your FireAngel. Ensure the green light is ‘on’continuously when charging. Test your FireAngel (see Operation,page 17).

WARNING: Before wiping with a damp cloth ensure that the power is switched off ordisconnected from the electrical circuit at the power distribution board/consumer unit tothe FireAngel

If you have any questions about the operation of your alarm, please contact the FireAngel TechnicalSupport Team between 10am - 4pm Monday - Friday

Telephone: +44 (0) 24 7623 6663 e-mail: technicalsupport@fireangel.co.uk

PROBLEM

You experience frequentunwanted alarms

FireAngel 'chirps'intermittently

FireAngel does notsound during testing

SOLUTION

If your FireAngels are interconnected, identify which unit iscausing the alarm. This is indicated by the red light flashing onceper second. If none of the FireAngels are causing the alarm,switch off electrical power and check the interconnect wiring.Switch off electrical power to the FireAngel. Remove buildup ofstatic electricity by wiping your FireAngel with a slightly dampcloth.Clean Your FireAngel (see Routine maintenance page 22).Check the location of your FireAngel (see Positioning page 6).Fully Charge Your FireAngel (see Operation page 17). Ensure thegreen light is ‘on’ continuously when charging.Test your FireAngel (see Operation page 17).

Fully Charge Your FireAngel (see Operation page 17). Ensure thegreen light is ‘on’ continuously when charging.Test your FireAngel (see Operation page 17).Check to make sure that your FireAngel is installed properly (seeinstallation page 10).Clean Your FireAngel (see Routine maintenance page 22).Check the location of your FireAngel (see Application &Positioning pages 3 - 6).

The light switch or test button may have been operated threetimes or more in a short time. Wait 15 minutes before re-testing.Fully Charge Your FireAngel (see Operation page 17). Ensure thegreen light is ‘on’ continuously when charging.Clean Your FireAngel (see Routine maintenance page 22).Check to make sure that your FireAngel is installed properly (seeinstallation page 10).Test your FireAngel using the test button (see Operation page17). If this works correctly but the light switch test feature doesnot, check the wiring.

26

27

DisposalYour FireAngel should be disposed in line with current disposal regulations, ifunsure please call the FireAngel technical support team for advice.

You can also return your smoke alarm for disposal. For return address seepage 30. Please include a note confirming the product is being returned fordisposal.

WARNING: - DO NOT ATTEMPT TO OPEN - DO NOT BURN

How to make your Home SaferInstalling smoke alarms is only one step in protecting your family from fires.You must also take steps to reduce the chances of fires starting in your home.If a fire does start, you must increase your chances of escaping. To have agood fire safety program you must:

1. Install Smoke Alarms properly. Carefully follow ALL the Instructions In thismanual. Keep your Smoke Alarms clean, and test them every week. SMOKE ALARMS THAT DO NOT WORK WILL NOT ALERT YOU.

2. Replace your Smoke Alarms immediately if they are not working properly.

3. Follow fire safety rules, and prevent hazardous situations:

• Use smoking materials properly. Never smoke in bed.

• Keep matches and cigarette lighters away from children.

• Store flammable materials in proper containers. Never use them near anopen flame or sparks.

• Keep electrical appliances and wiring in good condition. Do not overloadelectrical circuits.

• Keep cookers, fireplaces, chimneys, and barbecue grills grease free. Makesure they are properly installed, away from any combustible materials.

• Keep portable heaters and open flames such as candles away fromcombustible materials.

• Do not allow rubbish to accumulate inside your home as this providessources for combustion.

• Keep a supply of extra batteries on hand for your battery powered SmokeAlarms. (Note that the FireAngel does not need replacement batteries).

4. Develop a family escape plan and practice it with everyone in thehousehold, including small children if you have them.

• Draw a floor plan of your home, and find two ways to exit from eachroom. There should be one way to get out of each bedroom withoutopening the door, and alternate means of escape from an upper floor inthe event of the stairs being blocked (such as a fire escape).

• Make sure everyone recognises the smoke alarm signal and knows how toreact to it.

• If there are small children to consider it is important to explain to themwhat the smoke alarm signal means. Teach them that they must beprepared to leave the home by themselves if necessary. Show them how tocheck to see if doors are hot before opening them. Show them how tostay close to the floor and crawl if necessary. Show them how to use analternative exit if the door is hot and should not be opened.

• Decide on a meeting place a safe distance from your house. Again, if youhave them, make sure that all your children understand that they shouldgo and wait for you there if there is a fire.

• Hold fire drills at least every 6 months to make sure that everyone,including small children, know what to do to escape safely.

• Know where to go to call the Fire Brigade from outside your home.

Contact your local Fire Brigade. They will give you more ideas about how tomake your home safer from fires and how to plan your family's escape.

28

29

10-Year Limited WarrantyFireAngel Ltd warrants to the original purchaser that its enclosed smoke alarmbe free from defects in materials and workmanship under normal residentialuse and service for a period of ten years from the date of purchase.

Provided it is returned with postage prepaid and proof of purchase date,FireAngel Ltd hereby warrants that during the initial one year periodcommencing from the date of purchase FireAngel Ltd agrees to replace theunit free of charge. During the latter nine years of the warranty period,replacement shall be made at a charge to the customer not to exceedFireAngel Ltd’s cost. This warranty applies to the original retail purchaser fromthe date of original retail purchase and is not transferable. Proof of purchaseis required.

This warranty does not cover damage resulting from accident, misuse,disassembly, abuse or lack of reasonable care of the product, or applicationsnot in accordance with the user manual. It does not cover events andconditions outside of FireAngel Ltd’s control, such as Acts of God (fire, severeweather etc). It does not apply to retail stores, service centres or anydistributors or agents. FireAngel Ltd will not recognise any changes to thiswarranty by third parties.

FireAngel Ltd. shall not be liable for any incidental or consequential damagescaused by the breach of any express or implied warranty. Except to the extentprohibited by applicable law, any implied warranty of merchantability orfitness for a particular purpose is limited in duration for 10 years.

This warranty does not affect your statutory rights.

ReturnsWe recommend that you contact the FireAngel Technical Support Line in thefirst instance on +44 (0) 24 7623 6663 e-mail: technicalsupport@fireangel.co.ukas we may be able to remedy the problem quickly over the phone (this is toprevent unnecessary returns that take a longer time to process). If there is afault that we are unable to resolve then our technical support engineer willissue you with a return number so that this can be returned for testing.

To return your FireAngel under warranty, send it suitably packed and disabled(this will be explained by the FireAngel technical support engineer) withpostage prepaid; a note indicating the return number and describing thenature of the difficulty, with proof of date of purchase to:

FireAngel LimitedThe TechnoCentrePuma WayCoventry CV1 2TTUK

30

FireAngel Ltd. The Technocentre, Puma Way, Coventry CV1 2TT England

Technical Support Line 024 7623 6663 (1-800 523171 in Eire)

E-mail:technicalsupport@fireangel.co.uk

Web:www.fireangel.co.uk

Ref: SA0107 R2

Certified to BS 5446-1:2000

This product meets the requirements of the LPCB approval to BS 5446-1:2000 only when installed with a permanent live feed.

Certificate No.651a/01 to BS 5446-1:2000