Extron DTP HD DA4/DA8 4K 230/330 Setup Guide · 2015. 1. 8. · over tp over tp audio sig out link...
Transcript of Extron DTP HD DA4/DA8 4K 230/330 Setup Guide · 2015. 1. 8. · over tp over tp audio sig out link...
-
1
DTP HD DA4/DA8 4K 230/330 • Setup Guide
Overview
These Extron distribution amplifiers distribute one HDMI input signal to four (DTP HD DA4 4K models) or eight (DTP HD DA8 4K models) simultaneous outputs via shielded twisted pair (STP) cables. The amplifiers distribute the signal over a distance of up to 230 feet (70 meters) or 330 feet (100 meters) for resolutions up to 1080p @ 60 Hz, and 130 feet (40 meters) or 330 feet (100 meters) for resolutions up to 4K @ 30 Hz, depending on the model. This setup guide provides basic instructions for installation by an experienced installer. For complete instructions, see the DTP HD DA4/DA8 4K 230/330 user guide on the Extron web site (www.extron.com).
Typical DTP HD DA4/DA8 4K Application Examples
100-240V ~ 1.0A MAX
50/60 Hz
DTP HD DA4 330
LAN
3 41 2
OUTPUTSINPUT
HDMI LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
AUDIO
SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
HDMI HDMI3
HDMI4
21 CONFIGURABLE
100-240V ~ --A MAX
50-60 Hz AUDIO OUTPUT
TALLY OUT
CONTACT INL1 2
R
L R
Tx Rx G
321 4 +V
1 2 3 4 GRS-232
OUT
IN
HDMI
INPUT REMOTE
POWER12V 0.3A MAX
IPL PRO S3
GTx Rx RTS CTS GTx Rx RTS CTS GTx Rx RTS CTS
COM 1 COM 2 COM 3
LAN / PoE
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
iPad
LAPTOP
PC
DVD
DOC CAM
AUXILIARY
DISPLAY ON
DISPLAY OFF
MUTE
VOLUME
VOLUME
VideoMore
DVD Combined
RS-232
Displays with Speakers
HDMI
CATx Cable up to 330' (100 m)
CATx Cable up to 330' (100 m)
RS-232HDMI RS-232HDMI RS-232HDMI
Extron DTP HDMI 330 D RxReceiver
Extron DTP HDMI 330 D RxReceiver
VGA
Laptop Laptop Laptop Tablet
Audio HDMI HDMI HDMI
HDMI RS-232
Ethernet Ethernet
Ethernet
TCP/IPNetwork
ExtronTLP Pro 320C3.5" Cable Cubby TouchLink Pro Touchpanel
ExtronIN1604 HDFour Input Scaler
ExtronIPL Pro S3IP Link Pro Control Processor
ExtronDTP HD DA4 4K 330DTP Distribution Ampli�er
100-240V ~ 1.0A MAX DTP HD DA8 230
LANDTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
3 4 5 6 7 81 2
DTP
HDBT
OUTPUTSINPUT
HDMI LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
DTP
HDBT
DTP
HDBT
AUDIO
SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK SIG
OUT
LINK
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR
OVER DTP
HDMI HDMI3
HDMI4
21 CONFIGURABLE
100-240V ~ --A MAX
50-60 Hz AUDIO OUTPUT
TALLY OUT
CONTACT INL1 2
R
L R
Tx Rx G
321 4 +V
1 2 3 4 GRS-232
OUT
IN
HDMI
INPUT REMOTE
POWER12V 0.3A MAX
IPL PRO S3
GTx Rx RTS CTS GTx Rx RTS CTS GTx Rx RTS CTS
COM 1 COM 2 COM 3
LAN / PoE
50/60 Hz
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
MODEL 80
FLAT PANEL
iPad
LAPTOP
PC
DVD
DOC CAM
AUXILIARY
DISPLAY ON
DISPLAY OFF
MUTE
VOLUME
VOLUME
VideoMore
DVD Combined
RS-232
Displays with Speakers
HDMI
CATx Cable up to 330' (100 m)
CATx Cable up to 330' (100 m)
Extron DTP HDMI 330 D RxReceiver
RS-232HDMI
Extron DTP HDMI 330 D RxReceiver
VGA
Laptop Laptop Laptop Tablet
Audio HDMI HDMI HDMI
HDMI RS-232
Ethernet Ethernet
Ethernet
TCP/IPNetwork
ExtronTLP Pro 320C3.5" Cable Cubby TouchLink Pro Touchpanel
ExtronIN1604 HDFour Input Scaler
ExtronIPL Pro S3IP Link Pro Control Processor
ExtronDTP HD DA8 4K 330DTP Distribution Ampli�er
Front Panel
CONFIG
DTP HD DA4
INPUT OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOPTHRU
3 41 2
CONFIG
DTP HD DA8
INPUT OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOPTHRU
3 4 5 6 7 81 2
A B F
E
D
C
A B F
E
D
C
A Power status LED — Lights green when power is applied to the unit.
B USB Config port — Used for firmware updates, SIS configuration, and software control.
C Input Signal LED — Lights green indicating a signal is detected on the HDMI input.
D Input HDCP LED — Lights green indicating HDCP presence is detected on the HDMI input.
E Output Signal LEDs — Light green indicating a signal is detected on the HDMI outputs.
F Output HDCP LEDs — Light green indicating HDCP presence is detected on the HDMI outputs.
http://www.extron.com
-
2
DTP HD DA4/8 4K 230/330 • Setup Guide (Continued)
Rear Panel
50/60Hz
100-240V 1.0A DTP HD DA4 330
LAN
3 41 2
DTP
HDBT
OUTPUTSINPUT
HDMI LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
50/60Hz
100-240V 1.0A DTP HD DA8 330
LANDTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
3 4 5 6 7 81 2
DTP
HDBT
OUT
SIG LINK
DTP
HDBT
OUTPUTSINPUT
HDMI LOOP THRU
REMOTE
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
B
A C I
B D E F G H J K
A C I
B D E F G H J K
A Power input — Connect the provided IEC connector to a 100-240 VAC (50 or 60 Hz) power source.B Analog audio input — Connect an unbalanced stereo audio source to these 3.5 mm mini stereo jacks.
NOTE: The units do NOT embed analog audio onto the HDMI signal. This analog audio signal is transmitted simultaneously with audio embedded within the HDMI signal.
C Analog audio Loop Thru — Connect an audio system to this 3.5 mm mini stereo jack for local loop-through monitoring of the source audio.
D HDMI input — Connect a source device to this female HDMI type A connector.E HDMI Loop Thru — Connect a display to this female HDMI type A connector for local loop-through monitoring of the
source signal.
F DTP/HDBaseT configuration switch — Set this 2-position, recessed switch to configure the output between HDBaseT and DTP modes. When configured for HDBaseT, use an HDBaseT-compatible receiver. When configured for DTP, use a DTP-compatible receiver.
G DTP/HDBaseT outputs — Use shielded twisted pair (STP) cables to connect these 4 (DA4 models) or 8 (DA8 models) outputs to the inputs of a compatible receiver.
ATTENTION: • Do not connect these outputs to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
H Over TP RS-232/IR connectors — Use these 4 (DA4 series) or 8 (DA8 series) 3.5 mm, 5-pole captive screw connectors to pass bidirectional RS-232 and IR control between compatible devices.
I Reset button and LED — Press and hold the reset button for approximately 6 seconds to restore the unit to factory default settings. The reset LED will flash green, indicating that the default settings have been restored.
J LAN connector — Use an RJ-45 cable to connect this jack to a LAN for Ethernet control of the device.K Remote RS-232 connector — Connect an RS-232 device to this 3-pole, 3.5 mm captive screw connector to control the
DTP HD unit. Configure it as follows: 9600 baud rate, 8 data bits, 1 stop bit, no parity. See Installation on the next page for wiring instructions.
-
Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe+800.3987.6673 (Inside Europe Only)
+31.33.453.4040 +31.33.453.4050 FAX
Extron Asia+65.6383.4400+65.6383.4664 FAX
Extron Japan+81.3.3511.7655+81.3.3511.7656 FAX
Extron China+86.21.3760.1568 +86.21.3760.1566 FAX
Extron Middle East+971.4.299.1800+971.4.299.1880 FAX
Extron Korea+82.2.3444.1571+82.2.3444.1575 FAX
Extron India1800.3070.3777 (Inside India Only)
+91.80.3055.3777 +91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. www.extron.com
368-2545-50 Rev. A
01 15
DTP HD DA4/DA8 4K 230/330 • Setup Guide (Continued)
Installation1. Mount the HDMI DA unit in a suitable location (see the Mounting section of the DTP HD DA4/DA8 4K 230/330 user guide for
mounting options). Follow the instructions provided with the mounting kit.
2. Connect the USB or RS-232 connector (see the figure below) to a PC for configuration and maintenance. Use SIS commands or the Extron PCS program to configure EDID Minder, mute the video signal, mute the audio signal, adjust the video color bit depth, or monitor the signal and HDCP status, as required (see the DTP HD DA4/DA8 4K 230/330 user guide for more information).
RS-232
Tx Rx G
REMOTE
TransmitReceiveReceiveTransmitGroundGround
DB9 Pin LocationsFemale
5 1
9 6
Pin 2 = RxPin 3 = TxPin 5 = G
Computer DTP HD DA4/DA8
3. Connect the rear panel transmitter outputs (G) to the rear panel receiver inputs using shielded twisted pair (STP) cable.
NOTE: The DTP HD DA4/DA8 4K 230 and 330 products can transmit video, control, and audio (if applicable) signals up to 230 feet (70 meters) and 330 feet (100 meters), respectively.
For optimal performance, Extron highly recommends the following:
z RJ-45 termination with STP cable must comply with TIA/EIA-T568B wiring standard for all connections. For more information on cable wiring and termination, see the full product user guide at www.extron.com.
z Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400 MHz.
ATTENTION: • Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
• N’utilisez pas le câble AV Skew-Free UTP version améliorée UTP23SF d’Extron ou le câble STP201.
z Use shielded RJ-45 plugs to terminate the cable.
z Limit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches used. If possible, limit the number of patches to only 1 or 2 total.
z If RJ-45 patches must be used in the system, Extron recommends shielded CAT 6 (or better) patches.
4. Connect display devices to the transmitter and receivers.
NOTE: Use the LockIt HDMI cable lacing brackets provided to secure the HDMI connectors (see the LockIt HDMI Cable Lacing Bracket installation guide).
a. Connect and power on the display devices to the outputs on the compatible receivers.
b. (Optional) Connect and power on a local display device to the Loop-Thru connector (E).
5. Connect to a 110-240 VAC (50 or 60 Hz) power supply using the provided IEC power cord.
6. Connect and power on the source device.
http://www.extron.comhttp://www.extron.com