Extrem Vision Dvr Instalation

PC-BASED DIGITAL VIDEO RECORDER

INSTALLATIONMANUAL

2

Copyright 2004-2010 by SecuInfo Co., Ltd.

3

Table of Contents

Chapter 1 Introduction1.1 System Specification Recommendation ----------------------------------------------------- 61.2 Important Notes ----------------------------------------------------- 6

Chapter 2 Hardware2.1 DVR Line-up ----------------------------------------------------- 82.2 Sentry 1104 ----------------------------------------------------- 92.3 Sentry 1516 ----------------------------------------------------- 102.4 Sentry 2004 ----------------------------------------------------- 112.5 Sentry 2016 ----------------------------------------------------- 122.6 Sentry 3016 ----------------------------------------------------- 132.7 Sentry 3032 ----------------------------------------------------- 142.8 Sentry 5016 ----------------------------------------------------- 152.9 Sentry 5216 ----------------------------------------------------- 162.10 Sentry 5416 ----------------------------------------------------- 172.11 Sentry 6432 ----------------------------------------------------- 182.12 Audio Board (1ch) ----------------------------------------------------- 192.13 Audio Board (2ch) ----------------------------------------------------- 202.14 Audio Board (4ch) ----------------------------------------------------- 212.15 Audio Board (8ch) ----------------------------------------------------- 222.16 I/O Card ----------------------------------------------------- 232.17 Pan/Tilt Connection to DVR ----------------------------------------------------- 242.18 4-Ch BNC Guide Connection to DVR Board

----------------------------------------------------- 25

2.19 AV-Connection With Multi Boards ----------------------------------------------------- 26Chapter 3 Software

3.1 Device Driver Installation ----------------------------------------------------- 283.2 DVR Software Installation ----------------------------------------------------- 293.3 Folders Created After DVR Program Install

----------------------------------------------------- 32

3.4 DVR Program Image Files ----------------------------------------------------- 323.5 Language Alternation ----------------------------------------------------- 33

5

CHAPTER 1. INTRODUCTION

6

1.1 System Specification Recommendation

The below is the recommended computer specification to work with DVR board.

Model Sentry 1004 – 2016 Sentry 3016 - 3032 Sentry 5016 - 6432

CPU Cel 1.8GHz grade or above P4 2.0GHz grade or above P4 2.8GHz grade or above

Motherboar

dIntel Chipset

OS Win 2000/XP/Vista/7

Memory 128 Mbyte or above 256 Mbyte or above 512 Mbyte or above

VGA Intel onboard VGA / ATIIntel onboard VGA / ATI

Radeon 4XXX Series

Power 110/220V 300W

DirectX Version 9.0

1.2 Important Notes

1) Hard Drive Partition

- Set C: drive for Operating System only with size appx. 10Gbyte

- Set another drives (D:,E:….) for recording data with size 200 – 300Gbyte

2) Display Setup

- Set resolution at 1024x768 and High Color 16bit.

- Set “System Standby”, “Turn off monitor” and “Turn off hard disk” at “Never” in Display Properties\Power

Management Properties\Power Schemes.

3) Rebooting Setup

We highly recommend you to set automatic daily rebooting in idle time for most stable system operation.

4) Operating System

Windows 2000 / XP / Vista / 7

7

CHAPTER 2. HARDWARE

8

2.1 DVR Line-up

Model Video Input Display / Recording Audio Input

Sentry 1104 4Ch NTSC : 30fps / 30fps , PAL : 25fps / 25fps 1Ch

Sentry 1516 16Ch NTSC : 60fps / 60fps , PAL : 50fps / 50fps 2 Ch

Sentry 2004 4ChNTSC : 120fps / 120fps , PAL : 100fps /

100fps4Ch (Option)


100fps4Ch (Option)


200fps8Ch (Option)


200fps8Ch (Option)


100fps16Ch


200fps16Ch


400fps16Ch


400fps16Ch

9

2.2 Sentry 1104

Parts Included : one 1104LP board + one 4-Ch BNC Cable

Video In 1-4(BNC)

TV-Out Ch1-16(RCA)

Audio Input(RCA)

10

* 80mm slot guide is supplied together for low-rise PC case.

2.3 Sentry 1516

Parts Included : one 1516 board + one 16-Ch BNC Cable

TV Out Impedence Jumper Arrangment

NC : no impedence matching from capture card.

Impedence : match the impedence value of video signal to the analog TV monitor property. (Default)

Picture with low-rise guide

11

2.4 Sentry 2004

Parts Included : one 2016 board + one 4-Ch BNC Guide

16-Ch BNC Cable

Camera Input TerminalFor Back Panel Connetion DI/DO Terminal

TV Out

< 1516 Board >

Audio InputTerminal

To Motherboard Reset Terminal

To PC Reset Switch

Watchdog Cable Connection

12

2.5 Sentry 2016


DI/DO Terminal

Audio CardConnect Terminal

< 2016 Board>


To PC Reset Switch


To PC Reset Switch





TV Out

Ch2

Ch4

Ch3

Ch1 Pin No.1 GroundPin No.1 Signal

Pin No.2 GroundPin No.2 Signal



4-Ch BNC Guide #1

Box Open Side

13

2.6 Sentry 3016


TV Out

Camera Input TerminalFor Back Panel Connetion DI/DO Terminal


< 2016 Board >

16-Ch BNC Cable





14

2.7 Sentry 3032

Parts Included : two 2016 board + two 16-Ch BNC Cable

TV Out

DI/DO Terminal


< 3016 Board>

16-Ch BNC Cable


To PC Reset Switch





Camera Input TerminalFor Back Panel Connetion

15

2.8 Sentry 5016

Parts Included : one 5016 board + one BNC Cable for Video + one RCA Cable for Audio

TV Out

DI/DO Terminal


< 2016 Board #1>(Nearest to CPU)

16-Ch BNC Cable


To PC Reset Switch


DI/DO Terminal


< 2016 Board #2>

Ch 1-4,9-12,17-20,25-28

Ch 5-8,13-16,21-24,29-3216-Ch BNC Cable

TV Out Jump CablingAV InAV Out

To AV In of2016 #2




16

2.9 Sentry 5216

Audio In 1-16(RCA)

Video In 1-16(BNC)

TV-Out(RCA)


DI/DOInterminal

< 5016 Board >


To PC Reset Switch


17


Audio In 1-16(RCA)

Video In 1-16(BNC)

TV-Out(RCA)


DI/DOInterminal

< 5216 Board >



18

2.10 Sentry 5416


Audio In 1-16(RCA)

Video In 1-16(BNC)

TV-Out(RCA)


DI/DOInterminal

< 5416 Board >


To PC Reset Switch


19

2.11 Sentry 6432

Parts Included : one 6432 board + two BNC Cable for Video + one RCA Cable for Audio + one video

connection sub-board + two flat cable

* TV-Out Option ;

1 TV Monitor : Video Ch1~32 through TV-Out Port#1

2 TV Monitor : Video Ch1~16 through TV-Out Port#1 , Video Ch17~32 through TV-Out Port#2

Single channel or four channel in quad mode selectable.

Audio In 1-16(RCA)

Video In 1-16(BNC)

TV-Out #1(RCA)

Ch1~32(or Ch1~16)

Video In 17-32(BNC)

TV-Out #2(RCA)

Ch17~32

20

2.12 Audio Board (1-Ch)

< 1104 Board >PCI Slot

MIC In

< Audio Extension Board >

Audio In 1

Not Used

21

2.13 Audio Board (2ch)

PCI Slot

< Audio Extension Board >

Audio In 1-2

Not Used

< 1516 Board >

22


60 Pin Connection

Audio In 1-4

PCI Slot

< 4ch Audio Board >

< 120fps Board >

23


< Assembly Diagram >

3016 Board

8-Ch Audio Board

60 Pin Connection

PCI Slot

< 8ch Audio Board >

< Sentry 3016 Board >

Audio In 1-8(RCA)

24

2.16 I/O Card

< Assembly Diagram >

[ Sensor Input ]

1. Connection

Connect one signal line to COM port and connect

another signal line to the desired sensor number.

2. Operation

- Normal : 1-4 Terminal & COM Port Open

- Sensor Detection : 1-4 Terminal & COM Port

Close

3. At normal close mode, it works reversely.

[ Alarm Output ]

1. Connection

Connect both power lines to DO terminal

2. Operation

- Normal : DO Terminal Open

- Control Output : DO Terminal Close

3 D/O Voltage

.DC 30V, 1A or below

.DC 110V, 0.3A or below

.AC 125V, 500mA or below

To Serial Port on PC

PTZ Signal Cable

RX+RX-

TX- (Red)TX+ (Orange)

RS232RS485

Sensor Input

Alarm Output

To I/O Terminal

25

Notes ;

- N/O : Normal Open

- N/C : Normal Close

- DI Operation Mode (N/O or N/C) can be selected from Setup Mode of DVR Program

- D/O Delay Time can be adjusted from Setup Mode of DVR Program

2.17 Pan/Tilt Connection to DVR

In order to control PTZ function from DVR, connect the convertor which can convert RS232C to RS422/485

singal to COM port of DVR. Then connect signal line from receiver to convertor. Select the correct protocol

type from Sentry DVR program and match the address number of each PTZ camera to each one in PTZ

setup in Sentry DVR Program.

COM Port (RS232C)

RS422/485 Converter

26

2.18 4-Ch BNC Guide Connection to DVR Board

4-Ch BNC Guide

A

27

1 2 3 4 5 6 7 8 91

0

1

1

1

2

1

3

1

4

1

5

1

6

1

7

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Line Color Matching to Each Pin on Terminal

Pin

No.

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8

Signal Black Red Yellow Blue Black Red Yellow Blue

GND Brown Orange Green Violet Brown Orange Green Violet

Pin

No.

Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16

Signal Black Red Yellow Blue Black Red Yellow Blue

GND Brown Orange Green Violet Brown Orange Green Violet

In case of using over two pcs of 4-Ch BNC Guides, you can connect to Pin 5 ~ Pin 16.

Signal

Ground

Detail of A

Black

Brown

Red

Orange

Yellow

Green

Blue

Violet

Camera Input Terminal on DVR Board

Pin No.

28

2.19 AV-Connection with Multi Boards

When you connect TV line to 2 to 4pcs of 1004/1104 boards, 2pcs of 1516 board or 2 pcs of 2016 board,

the jump cable connection between boards are as below.

Sentry 1104 board

Sentry 1516 Board

Sentry 2016 Board

29

CHAPTER 3. SOFTWARE

30

3.1 Device Driver Installation

1. Run DVRDriverSetup.exe from Driver-2010-XX-XX folder in the software CD provided.

2. Select “Install DVR Device Driver” and press OK.

3. After driver installation completes, reboot the system.

4. When device driver is installed successfully, device driver is diaplayed in Device Manager as below.

- 1104 : 1 DVR Video Device + 1 DVR Audio Device Under DVR System

- 1516 : 2 DVR Video Device + 2 DVR Audio Device Under DVR System

- 2004/2016 : 4 DVR Video Device + 2 DVR Audio Device Under DVR System

- 3016/3032 : 8 DVR Video Device + 8 DVR Audio Device Under DVR System

- 5016/5216/5416/64432 : 1 DVR Video Device Under DVR System

31

3.2 DVR Software Installation

1. Run Setup.exe from HDServer-2010-XX-XX folder in the software CD provided.

2. Destination folder selection will be displayed. Press Next.

3. Choose the setup option. Then press Next.

32

4. Then program installation will be performed.

5. After installation completes, press Finish. Then the system will reboot.

6. After the system reboots, HD DVR software will start automatically (if HDDVSS4 is added in Startup

Menu successfully).

33

7. Then Recording Drive Setup menu will run.

8. Select the drive and Recording Type (Record : for recording data or Backup : for recorded data back-up)

other than C: drive. Press Apply. You can repeat the procedure to set multiple recording drives. Then

press OK.

9. Then DVR s/w will run as shown below.

35

3.3 Folders Created After DVR Program Installation

The below folders are created after DVR Program installation.

Folder Name Description

Language Language files exist

LogFile System Log files exist

PanTilt PTZ Driver files exist

Skin GUI skin file exists

Sound Sound files (*.wav) used in DVR program exist

Tools Utilities exist (Backup, Backup Player & CaptureClear)

Update Temp folder for download when real-time update

WebPages Web files for web service exists

3.4 DVR Program Image Files

There are a few image files used in DVR Program. The files can be replaced with the ones that

the users desire to have.

File Name Description SizeForma

tPath

Logo.bmpShown on blank channel where no

camera input exists from main GUI320 X 240 BMP

C:/DVSS4/

Image

MiniLogo.bmpShown on main GUI to display

supplier’s logo98 X 50 BMP

C:/DVSS4/

Image

Splash.bmp Shown when loading DVR Program 500 X 200 BMPC:/DVSS4/

Image

DVSS4WallPaper.b

mpWallpaper when used on DVR mode 1024 X 768 BMP

C:/DVSS4/

Image

Playbacklogo.bmpShown on blank channel where no

camera input exists from playback GUI320 X 240 BMP

C:/DVSS4/

Image

Disconnect.bmp Shown when no video signal 320 X 240 BMPC:/DVSS4/

Image

Note

- You can make image files and copy them to image folder.

- In order to apply customized images from install stage, you can make image

folder in installation folder (ex ; Server-2003XXXX) and copy the image files to

the folder.

36

3.5 Language Alternation

You can customize the language used in Sentry DVR Program Setup by editing language file in C”DVSS4\

Language folder. Normally the initial language is English after the installation.

Procedure

1. Go to “C”DVSS4\Language”.

2. Open “Lang.ENU.ini”.

3. Its content is ;

[SYSTEM]

MainColor = 166 184 206 (Basic Color)

TextColor = 0 0 0 (Font Color)

EditColor = 0 0 0

EditTextColor = 0 255 0

FontName = Verdana (Font Name)

FontSize=14 (Font Size)

FontStyle = 700 (Font Type Bold:700, Normal:400)

[MESSAGE] Language change starts below this line. Input the term with your language on the right to

“= “mark

cancel = cancel

yes = yes Ex ) yes = si (when changing from English to Italian)

…

[MENU]

[RECORD]

…

4. Close the language file after change’s done. Rename it to the one suitable (Lang_XXX.ini) for

your system language.

Language Script Code

Afrikaans Latin 1 AFK

37

Albanian Latin 1 SQI

Arabic Arabic ARA (Saudi Arabia)

ARB (Lebanon)

ARI (Iraq)

ARE (Egypt)

ARG (Algeria)

ARJ (Jordan)

ARK (U.A.E.)

ARL (Libya)

ARM (Monaco)

ARO (Oman)

ARQ (Qatar)

ARS (Syria)

ART (Tunisia)

ARU (Bahrain)

ARY (Yemen)

Armenian Armenian HYE

Azeri (Cyrillic) Cyrillic AZE

Azeri (Latin) Ext. Latin (code page 1254) AZE

Basque Latin 1 EUQ

Belarusian Cyrillic BEL

Bulgarian Cyrillic BGR

Catalan Latin 1 CAT

Chinese (PRC) Han (ideographic) CHS

Chinese (Taiwan) Han (ideographic) CHT

Chinese (Hong Kong

SAR, PRC)

Han (ideographic) ZHH

Chinese (Singapore) Han (ideographic) ZHI

Chinese (Macao SAR) Han (ideographic) ZHM

Croatian Latin 2 HRV

38

Czech Latin 2 CSY

Danish Latin 1 DAN

Dutch Latin 1 NLB (Belgium)

NLD (Netherlands)

English Latin 1 ENA (Australia)

ENB (Belize)

ENC (Canada)

ENG (U.K.)

ENI (Ireland)

ENJ (Jamaica)

ENL (Belize)

ENP (Philippines)

ENS (South Africa)

ENT (Trinidad)

ENU (U.S.)

ENW (Zimbabwe)

ENZ (New Zealand)

Estonian Ext. Latin (code page 1257) ETI

Faeroese Latin 1 FOS

Farsi Extended Arabic FAR

Finnish Latin 1 FIN

French Latin 1 FRA (France)

FRB (Belgium)

FRC (Canada)

FRL (Luxembourg)

FRM (Monaco)

FRS (Switzerland)

Galician Latin 1 GLC

Georgian Georgian KAT

German Latin 1 DEA (Austria)

DEU (Germany)

39

Greek Greek ELL

Gujarati Gujarati GUJ

Hebrew Hebrew HEB

Hindi Devanagari HIN

Hungarian Latin 2 HUN

Icelandic Latin 1 ISL

Indonesian Latin 1 IND

Italian Latin 1 ITA (Italy)

ITS (Switzerland)

Japanese Hirigana, Katakana, Kanji (ideographic) JPN

Kannada Kannada KAN

Kazakh Cyrillic KKZ

Konkani Devanagari KNK

Korean Hangul and Hanja KOR

Kyrgyz Cyrillic KYR

Latvian Ext. Latin (code page 1257) LVI

Lithuanian Ext. Latin (code page 1257) LTH

FYRO Macedonian Cyrillic MKI

Malay Latin 1 MSB (Brunei Darussalam)

MSL (Malaysia)

Marathi Devanagari MAR

Mongolian Cyrillic MON

Norwegian Latin 1 NON (Nynorsk)

NOR (Bokmal)

Polish Latin 2 PLK

Portuguese Latin 1 PTB (Brazil)

PTG (Portugal)

40

Punjabi Gurmukhi PAN

Romanian Latin 2 ROM

Russian Cyrillic RUS

Sanskrit Devanagari SAN

Serbian (Cyrillic) Cyrillic SRB

Serbian (Latin) Latin 2 SRL

Slovak Latin 2 SKY

Slovenian Latin 2 SLV

Spanish Latin 1 ESA (Panama)

ESB (Bolivia)

ESC (Costa Rica)

ESD (Dom. Rep.)

ESE (El Salvador)

ESF (Ecuador)

ESG (Guatemala)

ESH (Honduras)

ESI (Nicaragua)

ESL (Chile)

ESM (Mexico)

ESN (Spain, intl. sort)

ESO (Colombia)

ESP (Spain, trad. sort)

ESR (Peru)

ESS (Argentina)

ESU (Puerto Rico)

ESV (Venezuela)

ESY (Uruguay)

ESZ (Paraguay)

Swahili Latin 1 SWK

Swedish Latin 1 SVE (Sweden)

SVF (Finland)

Syriac Syriac SYR

41

Tamil Tamil TAM

Tatar Cyrillic TTT

Telugu Telugu TEL

Thai Thai THA

Turkish Ext. Latin (code page 1254) TRK

Ukrainian Cyrillic UKR

Urdu Extended Arabic URD

Uzbek (Cyrillic) Cyrillic UZB

Uzbek (Latin) Ext. Latin (code page 1254) UZB

Vietnamese Ext. Latin (code page 1258) VIT

Note ; In order to apply customized language from install stage, you can make language folder in

installation folder (ex ; Server-2003XXXX) and copy the corresponding language file to the folder.

< 2016 Board

>

Extrem Vision Dvr Instalation

Documents

Transcript of Extrem Vision Dvr Instalation