Exceptional Service Since 1986 Issue 1.1 Paints & Coatings · It’s easy to apply with the best...

Offering Full Technical Support

01692 406822Station Road, Worstead, North Walsham, NR28 9RZ

[email protected]

www.marineindustrial.co.uk

Quality Products Exceptional Service Since 1986

Seajet PAGE 1-5

Marine Industrial PAGE 19-20

Jotun PAGE 6-15

Ronseal & Bilgex PAGE 21

Owatrol PAGE 22-23

Marine Finish PAGE 16-19

Brava PAGE 21-22

Call Today

01692406822

Issue 1.1

Paints & Coatings

Burgess PAGE 23

Rylards PAGE 24

Hints & Tips PAGE 23-54

1



[email protected]


SEAJET 037 Coastal

A good performing, hard antifouling suitable for fresh water and coastal/brackish areas. This antifoul is suitable for all types of pleasure craft. Seajet Coastal 037 can also be applied to vessels which lay in a dry berth as well as high speed crafts of up to 70 knots. It has a excellent coverage, 10.8 square metres per litre.

Product Codes:2.5L Black SJ-690CR0013-22.5L Mid Blue SJ-690CR6941-22.5L Navy Blue SJ-690CR6094-22.5L Red SJ-690CR2991-2

SEAJET 033 Shogun

An award winning product which is used extensively throughout the UK and Europe on any vessel up to 40 knots. 033 Shogun is a self polishing antifouling which can be applied directly onto most previous coatings.

*Please check compatibility before over-coating*.

Product Codes: 750ml Black SJ-691VR0013-1750ml Mid Blue SJ-691VR6943-1750ml Navy Blue SJ-691VR6094-1750ml Red SJ-691VR2110-1750ml Shark Grey SJ-691VR0295-12.5L Black SJ-691VR0013-22.5L Green SJ-691VR5125-22.5L Mid Blue SJ-691VR6943-22.5L Navy Blue SJ-691VR6094-22.5L Red SJ-691VR2110-22.5L Shark Grey SJ-691VR0295-2

SEAJET 031 Samurai A antifoul for moderate fouling areas, for use on all all types of pleasure craft. Samurai is suitable for all boats up to 40 knots. It has great coverage, 9-10 square metres per litre. Based on Seajet’s award winning technology. Samurai has a hydration mechanism for controlled self-polishing action. Product Codes:2.5L Black SJ-667VR0013-22.5L Red SJ-667VR2104-22.5L Royal Blue SJ-667VR6920-2 2.5L Shark Grey SJ-667VR2095-2

SEAJET 039 Platinum

A high performance antifouling. Platinum is based on a new resin technology, offering a controlled, true self polishing action like no other product on the market.

Pack Product Codes:2L Black SJ-671FR0013-22L Mid Blue SJ-671FR6943-22L Navy Blue SJ-671FR6094-22L Red SJ-671FR2930-2

Comp A Product Codes: 3.54L Black SJ-671FR0013-A-3.543.54L Mid Blue SJ-671FR6943-A-3.543.54L Navy Blue SJ-671FR6094-A-3.543.54L Red SJ-671FR2930-A-3.54

Comp B Product Codes:0.460L SJ-671FR-B-2.67

SEAJET

2



[email protected]


SEAJET 032 Professional

Self-polishing antifoul designed for the professional applicator. Suitable for both fresh and salt water environments. Professional has a non boosted formulation. Provides great coverage, 9-10 square metres per litre. Professional is suitable for boats up to 40 knots. It has a hydration release mechanism for controlled self-polishing action. It has great opacity, covering existing surfaces with one coat.

***PLEASE NOTE: THIS PRODUCT IS FOR TRADE CUSTOMERS

ONLY, IT IS NOT AVAILABLE FOR RESALE***

Product Codes:5L Black SJ-623VR0013-55L Blue SJ-623VR6920-55L Red SJ-623VR2104-5

SEAJET Triple-Pack

Seajet’s new antifoul product is designed specifically for the protection of propellers, out-drives, trim-tabs and stern gear. Seajet Triple Pack is suitable for aluminium, aluminium-alloy and bronze substrates and contains 2-part epoxy primer system made up of a base (60% by volume) and hardener (40% by volume) mixed together prior to application. Following application of the primer, a single coat of Seajet 034 Emperor is then applied as the final top coat. 034 Emperor is one of Seajet’s best performing, self-polishing anti-foul products designed to prevent all forms of sea growth, barnacles, slime and algae from attaching itself to the protected surface.

Product Codes:0.5L Black SJ-255FR00130.5L Volvo Penta Drak Grey SJ-225FR02570.5L White SJ-225FR0257

SEAJET Peller Clean

An advanced and e nv i r o n m e n t a l l y friendly foul release product which contains an epoxy primer base coat and silicone top coat. Peller Clean contains no metals making it suitable for all propellers and stern drives. One pack will cover 1m².

Product Code:282ml SJ-251FR0000

SEAJET

SEAJET 034 Emperor

A high performance antifouling offering exceptional anti-slime qualities on all vessels up to 40 knots. 034 Emperor contains no copper oxide, meaning the white colour actually stays white and does not go green! This product can also be applied on all metal surfaces, after using the relevant primer, without the worry of electrolytic corrosion.

Product Codes:250ml White SJ-634VR0020-250750ml Black SJ-634VR0013-1750ml Mid Blue SJ-634VR6943-1750ml Navy Blue SJ-634VR6094-1750ml Red SJ-634VR2110-1 750ml White SJ-634VR0020-12.5L Black SJ-634VR0013-22.5L Mid Blue SJ-634VR6943-22.5L Navy Blue SJ-634VR6094-22.5L Red SJ-634VR2110-22.5L White SJ-634VR0020-2

3



[email protected]


SEAJET 130 Two Pack PU Gloss Varnish

This tough new two pack gloss varnish gives long term protection against UV light degradation, as well as holding up to minor bumps and scratches. It’s easy to apply with the best results achieved by laying on with a foam roller and ‘tipping’ off with a foam or conventional brush. This product is ideal for achieving a “mirror finish” when applied by hand. The coverage rate when brushed is 10-12 square metres per litre.

Product Code: 1L Clear SJ-570PZ006

SEAJET 120 UV Varnish High Gloss

Provides a beautiful high gloss finish for all types of wood. Seajet UV Varnish high gloss traditional tung oil varnish, contains UV absorbers to provide longer life. Easy to apply. This product is ideal for achieving a “mirror finish” when applied by hand. The coverage rate when brushed is 12-13 square metres per litre.

Product Code: 750ml Clear SJ-566AZ0061-1

SEAJET

SEAJET 132 Two Pack PU Gloss

This tough new two pack gloss paint & varnish gives long term protection against UV light degradation, as well as holding up to minor bumps and scratches. It’s easy to apply with the best results achieved by laying on with a foam roller and ‘tipping’ off with a foam or conventional brush. This product can also be used as a non-slip deck paint if used in conjunction with a non-slip additive.

Product Codes:1L Black SJ-570PZ0013 1L Mid Blue SJ-570PZ61511L Navy Blue SJ-570PZ6152 1L Red SJ-570PZ20931L White SJ-570PZ0020-1

SEAJET 122 Brilliance

This single component, urethane alkyd paint has very high gloss retention whilst remaining easy to apply using either brush or roller. Brilliance, although a single component product, will stand up to minor bumps and scratches.

Product Codes:750ml Navy Blue SJ-569AM6152-1750ml B.R Green SJ-569AM5192-1750ml Cream SJ-569AM0546-1750ml Mid Blue SJ-569AM6151-1750ml Red SJ-569AM2093-1750ml Oyster White SJ-569AZ0062-1750ml White SJ-569AM0020-12.5L White SJ-569AM0020-2

4



[email protected]


SEAJET 011 Underwater Primer

This primer is for below water-line areas only and should be used as a barrier coat prior to antifouling if the previous coating is un-known. 011 Underwater Primer contains aluminium making it relatively impermeable against moisture.

Product Codes:750ml Silver SJ-251CR0043-12.5L Silver SJ-251CR0043-2

SEAJET 017 Epoxy Binding System

For bare aluminium, bronze and any alloy surfaces after abrading and degreasing. 017 Epoxy Binding System gives superior performance compared to an etch primer. Ideal as a first coat on lead keels.

Product Code:1L Pack White SJ-203EE0020-1

SEAJET 012 Universal Primer Undercoat

A general purpose, alkyd based, single component primer and undercoat for above water line areas. Quick drying with excellent adhesion to all surface and subsequent coats.

Product Codes:750ml SJ-210AM0020-12.5L SJ-210AM0020-2

SEAJET

SEAJET 117 Epoxy Primer

A High performance two component epoxy primer suitable for both above and below waterline areas. Ideal for use on GRP hulls where up to four coats can be applied for osmosis preventative system, as well as metal keels and other metalic surfaces. White can ONLY be applied below the waterline when used in conjunction with the recomended osmosis treatment.

Pack Product Codes:1L Grey SJ-249EE0273-11L White SJ-249EE0020-1

Comp A Product Codes:1.75L Grey SJ-249EE0073-A-1.751.75L White SJ-249EE0020-A-1.75

Comp B Product Codes:0.75L Grey SJ-249EE073-B-0.750.75L White SJ-249EE0020-B-0.75

SEAJET 118 High Build Expoxy Primer

High build, high solids epoxy primer system which is particularly surface tolerant making it ideal for iron/ steel surfaces. Can also be used as an omosis preventative system on GRP if three coats are applied.

Comp A Product Code:2.2L SJ-460JE0043-A-2.21

Comp B Product Code:0.29L SJ-460JE0043-B-0.29

5



[email protected]


SEAJET & JOTUN

SEAJET Thinners A

For cleaning and thinning down of Seajet Antifoulings, 011 Underwater Primer and Seajet Speed.

Product Codes:1L SJ-908TR0061-1 5L SJ-908TR0061-5

SEAJET Thinners E

For cleaning and thinning down of Seajet Epoxy Primers 017, 117, 118 and Umeguard SX.

Product Code:1L SJ-901TE0061-1

SEAJET Thinners U

For cleaning and thinning down of Seajet Brilliance, Seajet UV Varnish, Seajet Satin Varnish and Seajet Universal Primer

Product Code:1L SJ-907TM0061-1

SEAJET Thinners P

For cleaning and thinning down of Seajet 132 Polyurethane Gloss and Seajet Polyurethane Gloss Varnish

Product Code:1L SJ-901TU0707-1

6



[email protected]


JOTUN

JOTUN MegaCote

Jotun MegaCote is a two component, fast curing, abrasion resistant, high solids epoxy anticorrosive coating. MegaCote is a multi-purpose epoxy primer for use on all areas – internal, external, above and below the water line.

Comp A Product Codes:3L Alu/ Red JN-MCOTE-R-A-3 (3:1)

3L Off White JN-MCOTE-W-A-3 (3:1)

13.5L Alu/ Red JN-MCOTE-A-R-13.5 (3:1)

13.5L Off White JN-MCOTE-A-W-13.5 (3:1)

Comp B Product Codes:1L JN-MCOTE-B-1 (3:1)

4.5L Alu/ Red JN-MCOTE-B-R-4.5 (3:1)

4.5L Off White JN-MCOTE-B-W-4.5 (3:1)

*Professional Application

JOTUN MegaPrimer

Jotun MegaPrimer is a two component, sandable epoxy primer/sealer. It is used as a primer/barrier between epoxy fairing compounds/fillers and polyurethane topcoats. MegaPrimer can be used as a ‘high build’ primer or can be thinned using Jotun Thinner 17 to create an excellent finishing primer.

Comp A Product Codes:2.4L Grey JN-MPRIMER-A-2.4 (4:1)

2.4L White JN-PRIMER-A-2.4 (4:1)

16L Grey JN-MPRIMER-A-16 (4:1)

Comp B Product Codes:0.6L JN-PRIMER-B-0.6 (4:1)

4L JN-PRIMER-B-4 (4:1)


JOTUN MegaSpeed Undercoat

Megaspeed Undercoat is a two-pack semi-gloss polyurethane undercoat that gives an ideal surface for topcoating. Very quick drying and with excellent sanding properties. As an undercoat in high-gloss polyurethane systems where an extremely smooth and pinhole-free surface is required prior to topcoating.

Comp A Product Codes:2L Off White JN-MSU-A-2 (4:1)

2L Grey JN-MSU-G-A-2 (4:1)

Comp B Product Codes:0.5L Off White JN-MSU-B-0.5 (4:1)

0.5L Grey JN-MSU-G-B-0.5 (4:1)


JOTUN MegaSealer

MegaSealer is a two component, high build epoxy-vinyl primer/tie coat and is recommended as a tie coat/sealer between an epoxy coating and antifouling. It bonds excellently to fresh, uncured epoxy coatings or abraded fully cured epoxy coatings. Can be applied over old antifoulings as a sealer coat prior to application of new antifouling. MegaSealer must not be thinned when used as a sealer coat on existing antifouling

Comp A Product Codes:3.75L Buff JN-MSEALER-A-3.75 (5:1)

15L Buff JN-MSEALER-A-15 (5:1)

Comp B Product Codes:0.75L JN-MSEALER-B-0.75 (5:1)

3L JN-MSEALER-B-3 (5:1)


7



[email protected]


JOTUN

JOTUN MegaFiller -Multi

A two-component, multi-purpose solvent free lightweight epoxy fairing compound/filler with increased resinity. Easy to mix with excellent application properties. The product’s increased resinity gives added durability, particularly where resistance to mechanical impact and water ingress are concerned. Megafiller Multi has excellent stability during large temperature fluctuations so that it retains an even profile. Despite its durability, the product has very good sanding properties and the Shore D hardness is around 65 (Shore D/1:65, as per ISO 868). Suitable for above and below-water applications, when part of an approved Jotun system. It does not require a full sealing layer of finishing filler (Megafiller Smooth) prior to overcoating. Solvent-based coatings, such as Megaprimer, may be applied directly onto Megafiller Multi.

Comp A Product Code:10L JN-MFM-A-10 (1:1)

Comp B Product Code:10L JN-MFM-B-10 (1:1)


JOTUN MegaFiller - Smooth

Megafiller Smooth is two pack solvent-free epoxy filler that leaves a very smooth surface. The product gives a hard film, but retains excellent sanding properties. Megafiller Smooth is suitable for above and below-water application. Normally used for re-finishing surfaces treated with Megafiller, or to repair existing epoxy or polyurethane systems. Suitable as part of an epoxy coating system on metal, GRP or wood substrates.

Comp A Product Code:2L JN-MFS-A-2

Comp B Product Code:2L JN-MFS-B-2


JOTUN MegaFiller Deck

A two-component, solvent-free ultra-lightweight epoxy fairing compound/filler that can be applied at very high thickness. It has minimal shrinkage (approximately 0.2%), strong adhesion and is more flexible than other epoxy fillers. Sandability is excellent and the Shore D hardness is around 40 (Shore D/1:41, as per ISO 868). Suitable for use on the decks of yachts made of steel, aluminium, composite or wood, when part of an approved Jotun system. Megafiller Deck is most often used beneath teak wood decking, which is glued onto the Megafiller Deck system.

Comp A Product Code:10L JN-MFD-A-10

Comp B Product Code:10L JN-MFD-B-10*Professional Application

8



[email protected]


JOTUN

JOTUN MegaYacht Royal

Megayacht Royal Antifouling is a self-polishing antifouling based on a copolymer binder. It is suitable for the special requirements of a large yacht. IMO Antifouling System Convention compliant AFS/CONF/26. Used as an antifoul on sailing and motor Megayachts operating in global service, with service periods up to 24 months.

Product Codes:5L Black JN-MROYAL-BLK-55L Blue JN-MROYAL-BL-55L Red JN-MROYAL-R-520L Black JN-MROYAL-BLK-2020L Blue JN-MROYAL-BL-520L Red JN-MROYAL-R-20

5L & 20L extened lead times. 5L tins are made to order.


JOTUN Megagloss HG

With outstanding abrasion resistance, excellent gloss and colour retention and very good flexibility, it is specially formulated for the yacht owner seeking the perfect finish. It meets the demands of both owners and applicators – an unrivalled mirror-like finish that will last and last in the most aggressive atmospheric conditions.

Product Codes:4.5L JN-MGLOSS-STANDARD-5(1:1)

4.5L JN-MGLOSS-SPECIAL-5(1:1)

4.5L JN-MGLOSS-CLEAR-5 (1:1)

This product can be colour mixed, a RAL or BS number and colour name will be required at time of ordering. For more information please contact the office on 01692 406822 or email [email protected].


JOTUN Megagloss AC

This is a high gloss, two component, high solids acrylic polyurethane topcoat with very good abrasion resistance and excellent gloss and colour retention. Specially formulated for easy application on top-class yachts and provides a finish that can be polished, if required. Recommended as a topcoat over an epoxy coating system where a durable high gloss finish is required in aggressive atmospheric exposure. Can be used on yachts and polished if polishing is unavoidable and required.

Product Codes:2.5L JN-MGLOSS-AC-STAND-2.5 (4:1)

2.5L JN-MGLOSS-AC-SPECIAL-2.5 (4:1)

2.5L JN-MGLOSS-AC-CLEAR-2.5 (4:1)



JOTUN MegaMatt

Jotun MegaMatt provides a superior solution where a matted finish is required. Apart from being an easy to mix product, its good application properties and outstanding silky-smooth finish. This product needs adding to the paint after the hardener is mixed with the paint

Product Code:2.5L JN-MEGAMATT


9



[email protected]


JOTUN

JOTUN MegaYacht Imperial

The ulitmate Jotun Yachting antifoul. A high performance tin-free self-polishing self-smoothening antifouling, specially designed for top-class Megayachts. The hydrolysing binder permits continuous exposure of fresh antifouling, so that hull is kept clean. As an antifouling on large sailing or motor yachts operating at medium or low speeds and/or with long stationary periods.

Product Codes:5L Black JN-IMPERIAL-BK55L Blue JN-IMPERIAL-BL55L Red JN-IMPERIAL-R55L White JN-IMPERIAL-W520L Black JN-IMPERIAL-BK2020L Blue JN-IMPERIAL-BL2020L Red JN-IMPERIAL-R2020L White JN-IMPERIAL-W20

5L & 20L extened lead times. 5L tins are made to order.*Professional Application

JOTUN Anti-Pest

A two-pack epoxy, suitable as a long exposure undercoat for epoxy and polyurethane systems and designed to prevent the osmosis in fibreglass boats. It can be used both as primer for all types of substrates, including steel, fibre glass, aluminium and marine timber, and as intermediate adhesion undercoat, for polyurethane or antifoulings on top of epoxy primers. It is particularly suitable for cycles against osmosis, and provides a good anti-corrosive effect.

Kit Product Code:750ml JN-AP-750 (4:1)

Comp A Product Code:2L JN-AP-A-2 (4:1)

Comp B Product Code:0.5L JN-AP-B-0.5 (4:1)

*All Yachting products are suitable for retail sales

JOTUN Vinyl Primer

A quick drying, one-component modified vinyl primer/sealer pigmented with aluminium flakes for added water resistance. It can be used both for underwater and topside areas. A universal sealer. It bonds well to fresh, uncured epoxy primers, whilst allowing antifoulings and other one-component coatings to bond onto it.

Products Codes:750ml JN-VP-7502.5L JN-VP-2.5


JOTUN Vinyl Primer Spray

A quick drying, one-component modified vinyl primer pigmented with aluminium flakes for added water resistance. It is designed to be used on stern drives, sailboats drives and other high metal components below the waterline. Gives excellent adhesion to the substrate as well as Aqualine Spray.

Product Code:400ml JN-VPS-0.4


10



[email protected]


JOTUN Lightweight Filler

Lightweight Filler is an ultra-lightweight two-component solvent-free epoxy fairing compound/filler that can be applied at very high thickness. It has minimal shrinkage (approximately 0.2%), above-average flexibility and very strong adhesion. Sandability is excellent with an approximate Shore D hardness of 50. Suitable as part of an epoxy coating system on metal, GRP or wood substrates.

Kit Product Code:1L JN-LWF-1 (1:1)

Comp A Product Code:2L JN-LWF-A-2 (1:1)

Comp B Product Code:2L JN-LWF-B-2 (1:1)


JOTUN

JOTUN Finishing Filler

A high density hand applied two component epoxy filler that leaves a smooth and strong surface. Good resistance to water and solvents, has very strong cohesion / adhesion properties and is more flexible than most epoxy fillers. Sandability is good with an approximate Shore D hardness of 75. It has a much lower viscosity than Lightweight Filler. Suitable for above and below water application, when part of an approved Jotun system. Normally used to finish surfaces treated with Lightweight Filler, in preparation for sealing with a solvented epoxy coating.

Comp A Product Code:0.5L JN-FF-A-0.5 (1:1)

Comp B Product Code:0.5L JN-FF-B-0.5 (1:1)


JOTUN TopGloss

A two part PU acrylic topcoat with good gloss and levelling characteristics. Suitable topcoat for epoxy or PU systems where a durable gloss finish is required. Suitable for unlined yacht interiors and engine room machinery where a dry temperature of 100 ºC is not exceeded. This product carries a low flame spread certification when used as a complete system.

Product Codes:1L JN-TGLOSS-STANDARD-1(3.5:1)

1L JN-TGLOSS-SPECIAL-1(3.5:1)

1L JN-TGLOSS-CLEAR-1(3.5:1)

4.5L JN-TGLOSS-STANDARD-4.5(3.5:1)

4.5L JN-TGLOSS-SPECIAL-4.5(3.5:1)

4.5L JN-TGLOSS-CLEAR-4.5(3.5:1)



JOTUN Ravilakk Varnish

Ravilakk is a glossy varnish, made from Chinese wood oil, synthetic amber and other high-grade raw materials. Ravilakk has good water and wear resistance, and dries quickly. This product gives the wood a slightly yellowish, golden tone. Ravilakk can be used on all wooden surfaces above the waterline both interier and exterior. New wood should be primed with Clipper I prior to treatment with Ravilakk.

Product Code:750ml JN-RL-750


11



[email protected]


JOTUN

JOTUN NonStop

A top class selfpolishing antifouling based on advanced hydrating binders. This characteristic assures a totally active surface continuously renewed. Ideal antifouling for all type of boats. Only white and grey colours recommended for aluminium hulls, no others colours to be used on aluminium, not recommended for boats sailing only on lakes.

Product Codes:750ml Black JN-NONSTOP-BLK-750750ml Blue JN-NONSTOP-BL-750750ml Dark Blue JN-NONSTOP-DB-750750ml Red JN-NONSTOP-R-750750ml White JN-NONSTOP-W-7502.5L Black JN-NONSTOP-BLK-2.52.5L Blue JN-NONSTOP-BL-2.52.5L Dark Blue JN-NONSTOP-DB-2.52.5L Red JN-NONSTOP-R-2.52.5L White JN-NONSTOP-W-2.520L Dark Blue JN-NONSTOP-DB-20*All Yachting products are suitable for retail sales

JOTUN Mare Nostrum SP

An efficient selfpolishing antifouling based on special binders assuring an active surface continuously renewed. The result is a clean hull for the whole season. It is suitable for all types of boats. Only white is recommended for aluminium hulls. The other colours are not to be used on aluminium.Not recommended for boats sailing only on lakes.

Product Codes:750ml Black JN-MARENOSTRUM-BL-750750ml Dark Blue JN-MARENOSTRUM-DB-750750ml Red JN-MARENOSTRUM-R-750750ml White JN-MARENOSTRUM-W-7502.5L Black JN-MARENOSTRUM-BL-2.52.5L Dark Blue JN-MARENOSTRUM-DB-2.52.5L Red JN-MARENOSTRUM-R-2.52.5L White JN-MARENOSTRUM-W-2.5


JOTUN Racing

An advanced hard antifouling that gives a hard, smooth and polishable surface. No chalking. Racing can be used on boats in all ranges of speed, but is especially suitable for speed boats in frequent use, providing an excellent result for a whole season. Only white and grey colours are recommended for aluminium hulls. The other colours are not to be used on aluminium.

Product Codes:750ml Blue JN-RACING-B-750750ml Dark Blue JN-RACING-DB-750750ml Red JN-RACING-R-750750ml White JN-RACING-W-7502.5L Blue JN-RACING-B-2.52.5L Dark Blue JN-RACING-DB-2.52.5L Red JN-RACING-R-2.52.5L White JN-RACING-W-2.5


JOTUN Aqualine Optima Spray

A grey or black high performance antifouling specially designed for easy application on drives, trim tabs, propellers and light metal parts below the waterline. A selfpolishing antifouling to be used on stern drives, sailboat drives, outboard motors, flaps and components made of aluminium or other light metals below the waterline. May not be suitable for high speed propellers.

Product Codes:400ml Black JN-AQOP-B-0.4400ml Grey JN-AQOP-G-0.4


12



[email protected]


JOTUN & JOTUN -MARINE

JOTUN Jotamastic 90

This is a two component, surface tolerant, abrasion resistant, high solids, polyamine cured epoxy mastic coating which may be applied in a wide range of film thicknesses. This product is part of a complete system which is certified not to spread flames. Recommended for use on steel where blast cleaning may not be possible and on hydrojetted surfaces still being moist. Can be used alone or in combination with various systems of primers and topcoats. Gives excellent corrosion protection both in salt and fresh water.

Comp A Product Codes:3.5L Aluminium JN-J90-A-ALU-3.5 (3.5:1)

3.5L Aluminium Red JN-J90-A-AR-3.5 (3.5:1)

3.5L Black JN-J90-A-BK-3.5 (3.5:1)

3.5L White JN-J90-A-W-3.5 (3.5:1)

15.6L Aluminium JN-J90-A-ALU-15.6 (3.5:1)

15.6L Aluminium Red JN-J90-A-AR-15.6 (3.5:1)

15.6L Black JN-J90-A-BK-15.6 (3.5:1)

15.6L White JN-J90-A-W-15.6 (3.5:1)

Comp B Product Code:1L JN-J90-B-1 (3.5:1)

4.4L JN-J90-B4.4 (3.5:1)

Wintergrade Range

Comp A Product Codes:3.5L Aluminium JN-J90W-A-ALU-3.5 (3.5:1)

3.5L Aluminium Red JN-J90W-A-AR-3.5 (3.5:1)

3.5L Black JN-J90W-A-BK-3.5 (3.5:1)

3.5L White JN-J90W-A-W-3.5 (3.5:1)

15.6L Aluminium JN-J90W-A-ALU-15.6 (3.5:1)

15.6L Aluminium Red JN-J90W-A-AR-15.6 (3.5:1)

15.6L Black JN-J90W-A-BK-15.6 (3.5:1)

15.6L White JN-J90W-A-W-15.6 (3.5:1)

Comp B Product Code:1L JN-J90W-B-1 (3.5:1)

4.4L JN-J90W-B4.4 (3.5:1)


JOTUN Jotamastic 87

Tailor-made corrosion protection for maintenance, the Jotamastic products are suitable for steel, aluminium and other substrates in tough environments such as energy, offshore, HPI and general infrastructure, ballast tanks, under water hulls, top sides, superstructures and cargo holds (suitable for grain carriage). Jotamastic 87 is a two-pack surface tolerant, abrasion resistant, high solids polyamine cured epoxy mastic coating which may be applied in high film thickness. Available with different hardeners for varying substrate temperatures, Standard (Std) and Wintergrade (WG). This product is a part of a complete system which is certified not to spread surface flames.

Comp A Product Codes:4.29L Black JN-J87-A-BK-4.29 (6:1)

4.29L Grey JN-J87-A-GY-4.29 (6:1)

4.29L Off White JN-J87-A-OW-4.29 (6:1)

16L Black JN-J87-A-BK-16 (6:1)

16L Grey JN-J87-A-GY-16 (6:1)

16L Off White JN-J87-A-OW-16 (6:1)

Comp B Product Code:0.71L JN-J87-B-0.71 (6:1)

2.71L JN-J87-B-0.71 (6:1)

Wintergrade Range

Comp A Product Code:4L Grey JN-J87W-A-GY-4 (4:1)

16L Grey JN-J87W-A-GY-16 (4:1)

Comp B Product Code:1L Grey JN-J87W-B-GY-1 (4:1)

4L Grey JN-J87W-B-GY-1 (4:1)

All JOTUN Marine products are for professional application only, not for resale or retail use. These products are not suitable for yachts or pleasure vessels!

13



[email protected]


JOTUN MARINE

JOTUN Vinyguard Silvergrey 88

A quick drying, modified vinyl primer. Used as a tie coat or as a sealer for an antifouling system to be compliant with IMO Anti-fouling System Convention (AFS/CONF/26). Can also be used as a primer/touch-up primer under alkyd and acrylic coatings for steel structures.

Product Codes:5L JN-VG88-GY-5

JOTUN Pilot QD Primer

A fast drying, alkyd based primer with zinc phosphate as active corrosion preventing pigments. As primer for steel and aluminium structures in moderate, non aggressive environments. It is fast drying and resistant against dry heat up to 120°C.

Product Codes:5L Grey JN-PQDP-G-55L Red JN-PQDP-R-55L White JN-PQDP-W-5

JOTUN Penguard FC

A high build, two component polyamide cured epoxy coating. It is an epoxy finish coat to be used when cosmetic appearance of an epoxy finish is acceptable. It can also be used as an anti corrosive primer.

Comp A Product Code:4L Black JN-PG-A-BLK-4 (4:1)

Comp B Product Code:1L BlacK JN-PG-B-BLK-1 (4:1)

JOTUN Tankguard DW

Tankguard DW is a solvent-free, two-pack epoxy tank coating.Tankguard DW is designed for use in Potable Water (drinking water) tanks.

Comp A Product Codes:10L Grey JN-TGDW-G-A-10 (2:1)

10L White JN-TGDW-W-A-10 (2:1)

Comp B Product Code:5L JN-TGDW-B-5 (2:1)

JOTUN Hardtop AS

Hardtop AS is a two-pack polyurethane topcoat with excellent gloss and colour retention. Hardtop AS bases are intermediates and need to be processed before use.As topcoat over an epoxy/epoxy mastic system where a durable, high gloss finish is required in aggressive atmospheric exposure. Cures at low temperatures.

Comp A Product Codes:5L JN-HTAS-STANDARD-5 (4:1)

5L JN-HTAS-SPECIAL-5 (4:1)

5L JN-HTAS-CLEAR-5 (4:1)

Comp B Product Code:1L JN-HTAS-B-1(4:1)


14



[email protected]


JOTUN - MARINE

JOTUN Pioneer Topcoat

An acrylic resin based topcoat. Pioner Topcoat bases are intermediates and need to be processed before use. Finishing coat for protection of steel and concrete in a variety of climatic conditions, exterior and interior. Water resistant and unsaponifiable. Quick drying and may be used at low temperatures. This product can be used as topcoat on top of Jotun’s Steelmaster range of intumescent coatings.

Product Codes:Comp A Product Codes:5L JN-PNR1-STANDARD-5 (4:1)

5L JN-PNR1-SPECIAL-5 (4:1)

5L JN-PNR1-CLEAR-5 (4:1)


JOTUN Pilot II

Easy-to-use topcoat. Pilot II is a conventional one component alkyd topcoat with excellent gloss properties and a wide colour selection. Good wetting properties makes Pilot II tolerant to most surfaces.

Product Codes:Comp A Product Codes:5L JN-PII-STANDARD-5 5L JN-PII-SPECIAL-5 5L JN-PII-CLEAR-5


JOTUN Hardtop XP

A two-pack high solid, aliphatic PU topcoat with excellent gloss and colour retention. For use as a glossy topcoat over most epoxy systems where a durable, weather-resistant finish is required in a wide range of aggressive atmospheres.

Comp A Product Codes:4.55L JN-HTXP-STANDARD-4.55 (10:1)

4.55L JN-HTXP-SPECIAL-4.55 (10:1)

4.55L JN-HTXP-CLEAR-4.55 (4:1)

Comp B Product Code:0.45L JN-HTXP-B-0.5 (10:1)


JOTUN Hardtop Flexi

A two component, high solid, flexible polyurethane coating with good gloss and colour retention. It has built in good corrosion protection and is also suitable as a single product system for maintenance when both corrosion protection and topcoat performance are desired.

Comp A Product Codes:4L JN-HTF-STANDARD-4 (4:1)

4L JN-HTF-SPECIAL-4 (4:1)

4L JN-HTF-CLEAR-4 (4:1)

Comp B Product Code:0.45L JN-HTXP-B-0.5 (4:1)


15



[email protected]


JOTUN

JOTUN Thinners No.2

Thinners No.2 is a general use thinner for most conventional alkyd or oil based paints.Thinners No. 2 is the solvent base for Pilot II.

Product Code:1L JN-TH-2-1

JOTUN Thinners No. 7

Solvent thinner. General purpose thinner for acrylic and chlorinated rubber paints and antifouling compositions.

Product Code:1L JN-TH-7-15L JN-TH-7-5


Solvent thinner. Thinner for polyurethane or similar paint products.

Product Code:1L N-TN-10-1

JOTUN Thinners No.18

A high quality solvent with a medium rate of evaporation. For improving flow and levelling properties when spraying Megaspeed Undercoat and when spraying Megagloss in average/moderate temperature conditions.

Product Codes:1L JN-TH18-15L JN-TH18-5


A high quality solvent with a slow rate of evaporation. Generally, for improving the flow and levelling properties of Megagloss products by slowing solvent evaporation/drying. Particularly suitable for brushing/rolling Megagloss. May be blended with Thinners No. 18 and used when spraying Megagloss in hot conditions.

Product Codes:1L JN-TH12-1

JOTUN Thinners No.17

Thinners No.17 is a solvent thinner. Recommended thinner for epoxies and similar paint products. Thinners No 17 is the solvent base for Jotamastic 87. This thinners can also be used with the MegaPrimer, MegaCoat and Anti-Pest Primers



A high quality solvent with a fast rate of evaporation. Use for improving flow and levelling properties when spraying Megagloss in cold temperatures. May be blended with Thinners No. 18 when spraying in more moderate conditions. Thinners No. 19 is not suitable for brush/roller applications.


16



[email protected]


MARINE FINISH

Marine Finish Two Pack PU Gloss Paint System

Developed by the trade, for the trade! Marine & Industrial have worked closely with a number of local boat restorers to formulate an easy to brush, high gloss finish, two pack polyurethane paint system. Great value for money and can be applied by either brush/roller or spray.

Pack Sizes:0.66L Comp A + 0.33L Comp B = 1L Pack1.66L Comp A + 0.33L Comp B = 2.5L Pack3.33L Comp A + 1.66L Comp B = 5L Pack

1L Gloss Comp A Product Codes:0.66L Beige MF-PU1001001-0.66 (2:1)

0.66L Black MF-PU100BLK-0.66 (2:1)

0.66L Bold Yellow MF-PU100363-0.66 (2:1)

0.66L Bondi Blue MF-PU100162-0.66 (2:1)

0.66L Brunswick Green MF-PU100226-0.66 (2:1)

0.66L Camouflage Grey MF-PU100626-0.66 (2:1)

0.66L Cream MF-PU10010C31-0.66 (2:1)

0.66L Dark Admiralty Grey MF-PU100632-0.66 (2:1)

0.66L Deep Cream MF-PU100353-0.66 (2:1)

0.66L Deep Ming Blue MF-PU10020C40-0.66 (2:1)

0.66L French Blue MF-PU100166-0.66 (2:1)

0.66L Grey MF-PU10000A05-0.66 (2:1)

0.66L Light Admiralty Grey MF-PU100697-0.66 (2:1)

0.66L Light French Blue MF-PU100175-0.66 (2:1)

0.66L Mediterranean White MF-PU1009016-0.66 (2:1)

0.66L Ochre Brown MF-PU1008001-0.66 (2:1)

0.66L Off White MF-PU10010B15-0.66 (2:1)

0.66L Pacific Blue MF-PU1001009-0.66 (2:1)

0.66L Pale Blue MF-PU1005024-0.66 (2:1)

0.66L Pale Green MF-PU1006021-0.66 (2:1)

0.66L Roundel Blue MF-PU100110-0.66 (2:1)

0.66L Survival Orange MF-PU100459-0.66 (2:1)

0.66L White MF-PU100WHT-0.66 (2:1)

2.5L Gloss Comp A Product Codes: 1.66L Amarillo Yellow MF-PU100731-1.66 (2:1)

1.66L Bondi Blue MF-PU100162-1.66 (2:1)

1.66L Broads Green MF-PU100122-1.66 (2:1)

1.66L Cobolt Blue MF-PU1005013-1.66 (2:1)

1.66L Cream MF-PU10008C31-1.66 (2:1)

1.66L French Blue MF-PU100166-1.66 (2:1)

1.66L Golden Yellow MF-PU100356-1.66 (2:1)

2.5L Gloss Comp A Product Codes Cont: 1.66L Light Ivory MF-PU1001015-1.66 (2:1)

1.66L Lilac MF-PU1004005-1.66 (2:1)

1.66L Marlin Blue MF-PU100960-1.66 (2:1)

1.66L Mauritus Blue MF-PU100509-1.66 (2:1) 1.66L Mint Green MF-PU100455-1.66 (2:1)

1.66L Pelican Blue MF-PU100891-1.66 (2:1)

1.66L Schwarzblau MF-PU1005004-1.66 (2:1)

1.66L Souvenirs Blue MF-PU1005015-1.66 (2:1)

1.66L Survival Orange MF-PU100459-1.66 (2:1)

1.66L Texas Yellow MF-PU100123-1.66 (2:1)

1.66L White MF-PU100451-1.66 (2:1)

5L Gloss Comp A Product Codes:3.33L Schwarzblau MF-PU1005004-3.33 (2:1)

3.33L Tele Grey MF-PU1007047-3.33 (2:1)

1L Gloss Comp B Product Code:0.33L MF-PU100HARD-0.33 (2:1)

2.5L Gloss Comp B Product Code:0.83L MF-PU100HARD-0.83 (2:1)

5L Gloss Comp B Product Code:1.66L MF-PU100HARD-1.66 (2:1)

Varnish Comp A Product Code:0.66L Clear MF-PU100CLEAR-0.66 (2:1)

Varnish Comp B Product Code:0.33L MF-PUHARD-0.33 (2:1)


Marine Finishes

17



[email protected]


MARINE FINISH

Marine Finish Two Pack PU Undercoat Paint System

Developed by the trade, for the trade! Marine & Industrial have worked closely with a number of local boat restorers to formulate an easy to brush, high gloss finish, two pack polyurethane paint system. Great value for money and can be applied by either brush/roller or spray.

Pack Sizes:0.75L Comp A + 0.25L Comp B = 1L Pack1.87L Comp A + 0.63L Comp B = 2.5L Pack

1L High Vis Comp A Products Code:0.75 White MF-PU200WHT-0.75 (3:1)

2.5L High Vis Comp A Products Code:1.87L White MF-PU200WHT-1.87 (3:1)

1L High Vis Comp B Product Code:0.25L MF-PU200HARD-0.25 (3:1)

2.5L High Vis Comp B Products Code:0.63L MF-PU200HARD-0.63 (3:1)

1L Original Comp A Product Codes:0.75L Ivory MF-PU30010C31-0.75 (3:1)

0.75L Pale Grey MF-PU30000A05-0.75 (3:1)

0.75L White MF-PU300WHT-0.75 (3:1)

2.5L Original Comp A Product Code:1.87L White MF-PU300WHT-1.87 (3:1)

1L Original Comp B Product Code:0.25L MF-PU300HARD-0.25 (3:1)

2.5L Original Comp B Product Code:0.63L MF-PU300HARD-0.63 (3:1)

Marine Finish Single Pack Gloss Paint

A high gloss single component enamel topcoat suitable for all types of vessels. Developed for trade applicators who require an easy to brush product with a good level of obliteration. Available in a wide range of BS and RAL colours, please contact the sales office for a full range.

Product Codes:1L Dark Admiralty Grey MF-EN100632-11L Platinum Grey MF-EN1007036-11L Porcelain Blue MF-EN10020C33-11L White MF-EN100WE-12.5L Black MF-EN100BL-2.52.5L Cream MF-EN1009001-2.52.5L Porcelain Blue MF-EN10020C33-2.52.5L Post Office Red MF-EN100POR-2.52.5L Oxford Blue MF-EN100105-2.52.5L Signal Green MF-EN1006032-2.52.5L Souvenirs Blue MF-EN1005015-2.52.5L True Blue MF-EN1005000-2.5L2.5L White MF-EN100WE-2.55L Oxford Blue MF-EN100105-5


Marine Finishes

18



[email protected]


Marine FInish Single Pack Undercoat Paint

A single pack enamel undercoat with a high level of filler and pigment content to ‘hide’ previous coatings and fill small pinholes. Developed for trade applicators who require an easy to apply undercoat to a wide range of substrates.

Product Codes:1L Pale Grey MF-EN20000A05-11L Red MF-EN20004E53-11L White MF-EN200WE-12.5L Pale Grey MF-EN20000A05-2.52.5L White MF-EN200WE-2.55L Pale Grey MF-EN20000A05-5


MARINE FINISH

Marine Finish Deck Paint

Single component alkyd paint system containing silica e-spheres to produce a non-slip, matt finish. Suitable for use on the majority of substrates.

Product Codes:1L Artic Blue MF-DP300AB1L Black MF-DP300BL1L Burgundy MF-DP300BY1L Cream MF-DP300CR1L French Blue MF-DP300FB1L Grey MF-DP300GY1L Light Admiralty Grey MF-DP300LAG1L Oxford Blue MF-DP300OB1L Pale Grey MF-DP300GY1L Pale Green MF-DP300PGR1L Pastel Blue MF-DP300PG 1L White MF-DP300WE 2.5L Grey MF-DP300GY-2.52.5L Oxford Blue MF-DP300OB-2.55L Pale Grey MF-DP300GY-5


Marine Finish Bilge Paint

A high quality, single component alkyd based bilge and locker paint. This product can be applied directly over GRP/Fibreglass and wood to leave a matt finish.

Product Codes:1L Grey MF-BP400GY1L Red MF-BP400RD1L White MF-BP400WE2.5L Anthracite Grey MF-BP400AGY-2.52.5L Grey MF-BP400GY-2.5

Marine Finish Black Tar Varnish

A low cost black tar paint which is intended for use as a protective finish against moisture and other corrosive agents on steel surfaces. Formulated to be applied using either brush or roller.

Product Code:5L Black MF-BTV-5

19



[email protected]


Marine Finish Deck Paint Additive

Silica e-spheres which can be added to a variety of matt and gloss paints to create a non-slip finish. For best results add no more than 40g of e-spheres to every 1L of paint.

Product Code:200g MF-DP300-SAND

MARINE FINISH & MARINE INDUSTRIAL

Marine Finish Bitumous Paint

A low cost, single part protective coating which is suitable for direct application on all metals and woods. Suitable for Narrow Boats etc

Product Code:5L Black MI-BP-5

White Spirit

Top quality White Spirit for cleaning of tools or thinning down petroleum based paints and varnishes.

Product Code:2L MI-WHS-2

Coppershield 2000

A water soluble epoxy based antifouling system which, when applied correctly, offers up to eight seasons without the requirement of re-applying. Contains 500gm of Resin Hardener (1:1 mix ratio) and 2kg of blown Copper Powder. Three coats must be applied on to a primer coat of West System epoxy to achieve the best results.

Product Code: 3.0KG MI-COPBOT-3

Genuine Turpentine

Genuine Turpentine is a natural product distilled from pine trees. It blends beautifully with oil based paints when thinning is required and will clean and protect expensive paint brushes much better than white sprit.

Product Code: 2.5L MI-TURPS-2.5

Marine Finish 2 Pack PU Solvent

High quality solvent for thinning down the Marine Finish 2 Pack Polyurethane Paints and washing of tools.

Product Codes:1L MF-SOL1005L MF-SOL100-5

20



[email protected]


Terebine Driers

A blended metallic drier which can be added to oil based paints to improve curing time in cold and damp environments. It can be added to oil based varnishes, undercoats, gloss paints etc at a maximum of 5%. Once mixed, leave product for 20 minutes before application.

Product Code: 25ml MI-TEREPIN-250

Raw Linseed Oil

Raw linseed oil penetrates and feeds wood leaving little or no surface coating. It’s especially recommended for application to oak, where its slower drying times gives the oil more chance of soaking into the dense fibre structure. Add a small amount of White Spirit to the first coat when applying to bare timber.

Product Code: 500ml MI-BLO-500

M&I Wood Perservative

A mixture of active ingredients and solvents to ensure a deeply penetrating and lasting finish. Protecting against dry rot, wet rot and wood boring insects.

Product Codes: 25L MI-CWP

MARINE INDUSTRIAL

Methylated Spirit

High quality methylated spirit for cleaning and degreasing surfaces.

Product Codes: 500ml MI-M-500 5L MI-M-5L

SCRUBBIS

An innovative tool to clean the boat hull in a timely and effective manner. The cleaning head has a buoyancy force attached to the telepscopic handle, the head is equipped with flexible scrapers that effectively clean the hull. The fouling is soft and has not hardened against the hull while the boat is still in the water. The buoyancy acting on the thin strip scrapers makes the scratch force very high and effective. It will also remove barnacles in the early stages.

Product Code:Large SCRUB-L

21



[email protected]


RONSEAL, BILGEX & BRAVA

Bilgex bilge Cleaner

A bilge cleaner which removes grease, scum and oil, leaving a fresh fragrance.

Product Codes:1L ICI-BILGEX-15L ICI-BILGEX-5

RONSEAL Trade Polyurethane Varnish

For exterior doors, windows and joinery, quick dry - 6 hour re-coat. Resists knocks, spills and heat. Tough high build finish

Product Codes:2.5L Matt RON-TR-348322.5L PU Gloss RON-TR-348302.5L PU Satin RON-TR-34831

Brava VG61 Defender Primer

Tung and linseed oil wood primer for exterior wood. It forms a long lasting waterproof barrier.

Product Code:1L Clear BR-VG61-1000

Brava VG64 Yacht & Boat Varnish

Classic high gloss, flexible, single component varnish, linseed oil based, ideal for varnishing high quality woods used in the marine environment.

Product Code:1L BR-VG64-1000

Brava VG66 Premium Gloss Varnish

High gloss tung & linseed oil marine varnish, U.V filters, extremely elastic, durable and protective. It is ideal for varnishing high quality woods used in the marine environment.

Product Code:750ml BR-VG66-750

Brava Impregnante Primer

A wood primer specifically formulated to give protection to all exterior or interior woods. Penetrating deep into the wood, it forms lasting barrier, providing the ideal base for all Brava Varnishes.

Product Code:750ml Clear BR-IMPREG-CL750

22



[email protected]


BRAVA & OWATROL

Brava VG62 Gloss Varnish

Yacht clear varnish, oil and polyurethane based, for the painter who desires a faster drying and a harder film than the VG 63 Varnish.

Product Code:1L Clear Gloss BR-VG62-10001L Clear Satin BR-VG62S-1000

Brava Royal PU Varnish

A two pack polyurethane varnish, with high gloss retention and good resistance to the marine environment.

Product Code:1L Clear BR-ROYALTRANS-1000

Brava VG63 Traditional Varnish

A Tung oil based clear varnish, it’s very elastic and penetrating and doesn’t crack. It contains UV Filters

Product Code:1L Clear Gloss BR-VG63-10001L Clear Satin BR-VG63S-1000

Net-Trol Wood Cleaner

A one-time marine wood cleaner and brightener which removes unsightly weathering and stains. Will not bleach woods but returns the original colour. Net-Trol is equally suitable for cleaning yellowing from GRP.

Product Codes:1L GN-NET-12.5L GN-NET-2.5

Deks Olje D1

D1 is a unique wood oil that is high in solids & penetrates deeply into the grain where it dries, stays & sets. Used on its own it needs occasional topping up of the surface as UV light and water wear it out. Deks Olje D2, can be directly applied onto D1 to create a long lasting deep gloss finish. Product Codes:1L GN-D1-12.5L GN-D1-2.510L GN-D1-1020L GN-D1-20L

Deks Olje D2

D2 is a high gloss varnish-like flexible finish which gives all types of woods a deep rich shine. D2 is applied to woods which are already fully saturated with D1, the two combine to give a long lasting finish.

Product Codes:1L GN-D2-12.5L GN-D2-2.510L GN-D2-1020L GN-D2-20

23



[email protected]


OWATROL & BURGESS

Owatrol Oil

A highly versatile penetrating oil which can be added to oil or alkyd based paints and varnishes to increase wet edge time and improve flow. Owatrol Oil can also be used neat on steel, to leave a durable finish and stop rust, as well as dry wood to stop paint peeling.

Product Codes:500ml GN-OWAT-500ML1L GN-OWAT-1L5L GN-OWAT-5L20L GN-OWATROL-20

Dilunett Paint Remover

Dilunett Solvent Free Paint Remover can remove up to 10 coats in just one application, removing everything from antifoulings to varnishes and most gloss paint systems. Easy to apply, Dilunett is a gel which can be applied to vertical surfaces without sagging. Caution this product is caustic.

Product Codes:1L GN-DIL-12.5L GN-DIL-2.5

Burgess Woodsealer

Burgess Woodsealer is a long lasting wood treatment which contains UV blocking pigments that help to prevent degradation by the sun’s rays. It will not crack or craze like traditional varnishes. It can be used on its own to leave a matt finish or over-coated using Top Gloss or Clearseal to create a gloss finish.

Product Codes:1L BS-WS-12.5L BS-WS-2.55L BS-WS-5

Burgess Clearsealer

A tough and long lasting wood finish treatment for areas not subjected to direct sunlight. Ideal for interior use where minimum colouration is required. It is UV resistant but, unlike Burgess Woodsealer, it does not contain UV blocking agents. Apply Clearseal on top of Woodsealer.

Product Codes:1L BS-CS-12.5L BS-CS-2.55L BS-CS-5

Burgess Top Gloss

When applied over Burgess Woodsealer, Top Gloss leaves a crystal clear gloss finish. Top Gloss is UV stable but does not contain UV blockers so should always be applied over the top of Burgess Woodsealer.

Product Codes:1L BS-TG-12.5L BS-TG-2.55L BS-TG-5

MOQ’s may apply, please ask for details

Burgess Creepy Crackseal

Burgess crackseal is a highly penetrating resin which will work its way into the smallest cracks and penetrate wherever water is able to. These properties make it ideal for leaky hatches, deck lights and other troublesome areas.

Product Code: 100ml BS-CS-100

24



[email protected]


Rylards Gloss

A single component, alkyd based gloss enamel with fantastic coverage and high build capabilities. Leaves a fantastic finish at a great value.

Product Codes:750ml Anchusa Blue RY-G-00019-750750ml Battleship Grey RY-G-BSGR-1750ml Cream RY-G-00003-750750ml Crimson RY-G-00010-750750ml Dolphin Green RY-G-00029-750750ml Eau de Nil RY-G-00027-750750ml Jasmine RY-G-00005-750750ml Light BS Grey RY-G-00014-750750ml Light Teak RY-G-00012750ml Navy Blue RY-G-00022-750750ml Magnolia RY-G-00002-750750ml Mead Green RY-G-00104-750750ml Pirate Red RY-G-00008-750750ml Smalt RY-G-00020-750750ml Signal Red RY-G-00009-750750ml Silver Fox RY-G-00013-750750ml White RY-G-00100-750750ml Yellow RY-G-00006-7502.5L Anchusa Blue RY-G-00019-2.52.5L Cream RY-G-00003-2.52.5L Crimson RY-G-00010-2.5 2.5L Light BS Grey RY-G-00014-2.52.5L Navy Blue RY-G-00022-2.52.5L Post Service Red RY-G-00106-2.52.5L Smalt RY-G-00020-2.52.5L Signal Red RY-G-00009-2.52.5L White RY-G-00100-2.52.5L Yellow RY-G-00006-2.5

Rylards Undercoat

A single component, alkyd based undercoat with fantastic coverage and high build capabilities. Leaves a fantastic finish at a great value.

Product Codes:750ml British Racing Green RY-U-BRGREEN-1750ml Cream RY-U-00035-750750ml Dark Battleship Grey RY-U-00047750ml Signal Red RY-U-00041-750750ml White RY-U-07963-7502.5L Blue RY-U-00053-2.52.5L Grey RY-U-GRY-52.5L White RY-U-07963-2.5

Rylards Yacht and Boat Varnish

A classic high-gloss conventional yacht varnish, formulated for its excellent brush application qualities and good drying properties - even when used in typical boatyard conditions. Yacht and Boat Varnish dries to an exceptionally hard, durable finish which maintains its deep gloss for many years.

Product Codes:750ml Clear RY-VG612-7502.5L Clear RY-VG612-2.5

RYLARDS

25



[email protected]


Seajet PrimersType

Product SelectorSeajet 011

Underwater PrimerSeajet 012 Universal

Primer Undercoat

Seajet 117 Multipurpose Epoxy

Primer

Seajet 118 Ultra-Build Epoxy Primer

Seajet 017 Epoxy Bonding Primer for

Alloys

Where can I use the primer?

Underwater only Above water only All areas All areas All areas

Recommended as:

Binder coat for old antifouling. Primer for

antifouling

Primer and undercoat for one component

topcoat

Multipurpose high performance primer

for antifouling and two component topcoats

Protecting against gel-coat blistering. Metal

surfaces where preparation is not

ideal

First primer coat for aluminium, alloys and

bronze

Main benefits

Quick drying. Excellent adhesion to existing

antifoul and subsequent coats.

Good sea water resistance

Quick drying. Excellent adhesion to all surfaces and

subsequent coats

Long term durability for fibreglass, steel

and aluminium. Suitable for all areas of

the boat

High build, fewer applications are

required. Suitable for all areas of the boat. Tough, durable finish

Superior performance compared to etching

primer. Suitable for all areas of the boat

Most suitable for fibreglass

PP PP PP PP P

Most suitable for wood

PP PP P P X

Most suitable for aluminium

P P P P PP

Most suitable for steel

P P PP PP X

Most suitable for osmosis prevention

X X PP PPP X

Most suitable for propellers, stern gear etc

P X P P PP

Most suitable for cast iron steel or lead kneels

P X P PP PP

Colours Silver Off White Silver Grey, White Silver Bronze WhiteCoverage rate when rolling 8.4m²/L 9-10m²/L 8.5m²/L 17.8m²/L 8.4m²/L

Pack size 750ml, 2.5L 750ml, 2.5L 1L, 2.5L 2.5L 1L, 2.5L

Note - Key P Suitable PP Very Suitable PPP Ideal X Unsuitable

One component for easy application Two component for high performance results

HINTS & TIPS - SEAJET

Seajet Primers

26



[email protected]


AntifoulingType HardProduct Selector 039 Platinum 034 Emperor 033 Shogun 031 Samurai 037 Coastal

Overall Performance out of 10

10 9 8 7 7

Recommended for

Highest fouling areas for all types

of boats except aluminium. New advanced resin

technology

Very high fouling areas for all types

of boats. New advance biocide

package.

High fouling areas for all types of

boats

Moderate fouling areas for all types

of boats

Great value for money. Suitable for all types of pleasure craft.

Good performance in inland

waterways

Main benefits

Ultimate performance. Best

antifouling performance. Ideal for serious racers and blue water

cruisers

Great performance against fouling. Ideal for club racers. Bright

colours. Highly effective against

slime

Excellent all round performance(test winning heritage) Two coats will last

two seasons.

Great value for money. Good all-

round performance

Great value for money. Suitable from fast for all kinds of boats.

Suitable for inland waterways

Number of coats per season

1 (2) 1 (2) 1 (3) 1 (2) 1 (3)

Can be applied to last up to

Two seasons (3 roller coats)



One Coat, one season

One Coat, one season

Suitable for motor boats and yachts?

Yes, up to 40 knots

Yes, up to 40 knots

Yes, up to 40 knots

Yes, up to 40 knots

Yes, up to 70 knots

Suitable for aluminium

X PPP X X X

Suitable for fibreglass wood and steel

PPP PPP PPP PPP PPP

Suitable for fresh water

X PP PP PP PP

Suitable for drying mud berths

X P P PP PPP

ColoursMid Blue, Navy Blue, Red, Black

White, Mid Blue, Navy Blue, Red,

Black

Shark Grey, Mid Blue, Navy Blue,

Red, BlackShark Grey, Blue

Red, BlackMid Blue, Navy Blue, Red, Black

Coverage rate 9.6m²/L 11.2m²/L 8.8m²/L 9.2m²/L 10.8m²/L

Pack size 2L, 4L 750ml, 2.5L 750ml, 2.5L 2.5L 2.5L


(1) Comparative performance testing shows relative performance, where 10 is perfection in all fouling conditions and 0 is no antifouling. (2) Apply 1 extra coat on the waterline and leading edges for a season

Self Polishing


Seajet Antifouling

27



[email protected]


Seajet Propeller CoatingType Foul Releases Self PolishingProduct Selector Seajet Pellerclean Seajet Triple PackOverall Performance out of 10 1 8 8

Recommended forPropellers, stern gear and trim tabs. Friendly to the

environment

Propellers, stern gear and trim tabs

Main benefitsBiocide-free. Releases

fouling when moving, long term protection. 1

All products in 1 kit! Antifouling in bright colours

Number of coats per season 2 2

Can be applied to last up to Three Seasons Three Seasons

Suitable for motor boats and yachts?

Yes up to 30 knots Yes up to 40 knots

Suitable for aluminium P P

Suitable for fibreglass, wood and steel

P P

Suitable for fresh water P P

Suitable for drying mud berths

P P

Colours ClearWhite, Black, Volvo Penta

Dark GreyCoverage Rate 0.7m²/box 2.5m²/L

Pack size Box Set Triple Pack at 500ml


(1) Slime may need to be removed by gentle sponge cleaning or low pressure washing

Seajet ThinnersTypeProduct Selector Thinner A Thinner U Thinner E Thinner P

Recommended forSeajet antifouling, Seajet

Speed, Seajet 011 Underwater Primer

Seajet Brilliance, Seajet Universal Primer, Seajet

UV Varnish

Suitable for all Seajet epoxy primers

Seajet 132 PU Gloss

Main benefits

Cleaning Brushes and spray equipment. Thinning for easier

application


application


application


application

Suitable for use on Gelcoat

P

To degrease and cleanP



To degrease and clean

Pack size 1L 1L 1L 1L


Thinners for 1 component paint Thinners for 2 component paint


Seajet Propeller Coating

Seajet Thinners

28



[email protected]



Antifouling Compatibility Table

Existing Product

Seajet 031 SamuraiSeajet 032 ProfessionalSeajet 033 ShogunSeajet 034 Emperor

Seajet 039 Platinum Seajet 037 Coastal

Attiva Professional AFP 0 2 0

Attiva Drake 0 2 0

Attiva Giraglia 0 2 0

Attiva Superwhite 0 2 0

Awlgrip Awlstar Gold Label 0 2 0

Boero Altura 619 (without Regaflon/PTFE)

1 2 1

Boero Corsa 642 (without Regaflon/PTFE)

1 2 1

Boero Corsa Regatta 619 (without Regaflon/PTFE)

1 2 1

Boero Mistral 633 (without Regaflon/PTFE)

1 2 1

Boero Scirocco 622 1 2 1Compass Antifouling (All Types)

1 2 1

Gold Label 1 2 1

Hard Antifouling 1 2 1

Hempel Bravo 1 2 1

Hempel Broads 1 2 0

Hempel Combic 1 2 1Hempel Cruising Performer/ Tiger Cruising

0 2 0

Hempel Dynamic 0 2 0

Hempel Glide Cruise 0 2 0

Hempel Globic 1 2 1

Hempel Hard Racing 1 2 1

Hempel Hard Racing Ultra 3 3 1

Hempel Mille 0 2 0

Hempel Ocean Performer 0 2 0

Hempel Ocean 1 2 1

Hempel Olympic 1 2 1

Seajet Antifouling Compatibility Chart

29



[email protected]




Existing Product



Hempel Tiger Extra/ Titan Ultra

0 2 0

Hempel Waterline 2 2 2

International Micron 55/66 0 2 0

International Micron 77 0 0 0International Micron Extra/ CSC

0 2 0

International Optima 0 2 0

International Uni-Pro 1 2 1

International VC17M 3 3 3

International Boatguard 1 2 0

International Bottomcoat 0 2 0

International Cruiser Premium/ Uno

0 2 0

International Interspeed Ultra 1 2 0

International Micron Extra/ CSC

0 2 0

International Optima 0 2 0International Superyacht 800/900

0 2 0

International Trilux 1 2 0

International VC Offshore 1 2 1

International Waterways 1 2 0

Jotun Mare Nostrum 1 2 0

Jotun MagaYacht Imperial 1 1 1

Joton Non Stop 0 2 0

Jotun Racing 0 2 0

Jotun Super Tropic 1 2 0

Nautix A2 0 2 0

Nautix A3 1 2 0

Nautix A3 T.Speed 3 3 3

Seajet Antifouling Compatibility Table

30



[email protected]




Existing Product



Nautix A4 1 2 1

Nautix A4 T.Speed 3 3 3

Nautix Le Marin 1 2 1

Naytix Performer 0 2 0

Niemeyer/van. Hoveling 1 2 1

Plasticoque Allegro 0 2 0

Plasticoque Aviso 0 2 0

Plastimo Classic 0 2 0

Plastimo Performance 0 2 0

Plastimo Racing 0 2 0Seajet 031 Samurai/ 033 Shogun/ 034 Emperor 0 2 0

Seajet 039 Platinum 0 0 0Seajet 037 Coastal/ 030 Warrior 0 2 0

Seajet Speed Finish 3 3 3

Sikken Chloorrubber 2000 1 2 1

Soft Antifouling 2 2 2

Soromap AF1 1 2 1

Soromap AF2 1 2 1

Soromap AFC+ 1 2 1

Stoppani Stopmar 0 2 0

Stoppani Fisher 1 2 1

Stoppani Noa Noa Rame 1 2 1Stoppani Noa Noa Rame Autopolissant 1 2 1

Stoppani Sibelius 1 2 1

Stoppani Sibelius H.M 1 2 1

Seajet Antifouling Compatibility Chart

31



[email protected]




Existing Product



Stoppani Sintofouling Rame 1 2 1

Teflon Antifouling 3 3 3

Tin-Based SPC Antifouling 0 2 0

Unknown Antifouling 2 2 2

Waterline 2 2 2

XM C2000 Eroding 1 2 0

XM HS3000 Eroding 1 2 0

XM P4000 Hard 2 2 0

2 - As above but apply a barrier coat of Seajet 011 Underwater Primer before applying the new coating

3 - Remove the existing antifouling and apply the recommended primer system before applying antifouling

0 - Apply antifouling after removing slime or fouling with high pressure fresh water, remove loose antifouling and spot repair with the recommended primer

1 - As above but light wet sanding of the existing antifoul is required, then rewash before painting

Seajet Antifouling Compatibility Table

32



[email protected]



How Much Paint To UseAntifouling

Ft Mt Fin Keel Full KeelMotor Boat

Fin Keel Full KeelMotor Boat



20.00 6.10 1.05 1.35 1.60 0.86 1.10 1.30 0.86 1.10 1.30 0.98 1.26 1.50

25.00 8.00 1.60 1.85 2.10 1.30 1.51 1.71 1.30 1.51 1.71 1.50 1.73 1.97

30.00 9.15 2.35 2.35 2.61 1.92 1.92 2.12 1.92 1.92 2.12 2.20 2.20 2.44

35.00 10.67 2.61 3.15 3.95 2.12 2.57 3.22 2.12 2.57 3.22 2.44 2.95 3.70

38.00 11.59 3.15 4.20 4.71 2.57 3.43 3.84 2.57 3.43 3.84 2.95 3.94 4.41

40.00 12.20 3.28 4.46 5.26 2.67 3.63 4.28 2.67 3.63 4.28 3.07 4.17 4.92

44.00 13.42 3.70 5.63 6.56 3.01 4.59 5.34 3.01 4.59 5.34 3.46 5.27 6.14

51.00 15.56 4.46 6.98 8.24 3.63 5.69 6.71 3.63 5.69 6.71 4.17 6.53 7.71

Primers

Ft Mt Fin Keel Full KeelMotor Boat



20.00 6.10 1.00 1.00 1.00 2.30 2.40 2.30 2.30 2.40 1.60

25.00 8.00 1.50 1.75 1.50 2.60 3.50 2.60 2.60 3.50 3.00

30.00 9.15 2.25 2.50 2.50 3.30 4.90 3.30 3.30 4.90 4.90

35.00 10.67 2.50 3.75 3.75 3.90 5.90 3.90 3.90 5.90 7.40

38.00 11.59 3.00 4.25 4.25 4.60 6.90 4.60 4.60 6.90 8.70

40.00 12.20 3.10 4.50 4.50 4.90 7.40 4.90 4.90 7.40 9.30

44.00 13.42 3.50 4.75 4.75 5.40 8.10 5.40 5.40 8.10 10.20

51.00 15.56 4.25 5.75 5.75 6.60 9.90 6.60 6.60 9.90 10.60

How to calculate the area to be painted1 Underwater surface area of the Sali boat (Fin Keel)

LWL x (B + D) x 0.5 = underwater area

2 Underwater surface area of the Sali boat (Full Keel/ Bilge Keel)


3 Underwaer area of motor boat


4 For Freeboard

(Length over all + B) x (F x 2) Freeboard area

5 For the deck

(Length over all + B) x 0.75 deck area

Total litres required =

Key:LWL Length at water lineB Beam (maximum width)D Draft (to be base of the keel)F Freeboard height (waterline to gunwale)

Total surface area (m²)Coverage rate of relevant paint (m²/L)

Seajet 039 (per coat in litres)

Size of Boat Seajet 011 (per coat in litres)


Seajet 117(per coat in litres)

Size of Boat Seajet 033 (per coat in litres)


Seajet 037(per coat in litres)

How Much Paint To Use

33



[email protected]



Drying Times - Primers

TemperatureDrying Time(at DFT 60 µ)

Overcoating Intervals (at DFT 60 µ)

Pot Life Remarks

5°CTouch dry: 1 hourHard dry: 6 hours

Minimun: 12 hoursMaximum with itself : -

- * 7 Days

10°CTouch dry: 50 minsHard dry: 5 hours


- * 7 Days



- * 7 Days

30°CTouch dry: 25 minsHard dry: 2.5 hours


- * 7 Days

* Maximun with application of any antifouling

Note: Drying times and overcoating intervals will increase with increasing film thickness applied.

Before re-coating, always check that the existing paint film is 'through' dry



Pot Life Remarks

5°C - -

10°C - -

20°CTouch dry: 4 HoursHard dry: 24 hours

Minimun: 24 hoursMaximum with itself : none

- -

30°C - -

Note: Drying times and overcoating intervals will increase with increasing film thickness appliedBefore re-coating, always check that the existing paint film is 'through' dry

SEAJET 011

SEAJET 012


34



[email protected]






Pot Life Remarks


Minimun: 16 hoursMaximum with itself : 7 days

24 Hours -



20 hours -



18 Hours -



12 Hours -


Temperature Drying Time(at DFT 125 µ)


Pot Life Remarks


Minimun: 24 hoursMaximum with itself : None

24 Hours * 7 Days

10°CTouch dry: 2 hoursHard dry: 24 hours


18 Hours * 7 Days

20°CTouch dry: 1.2 hoursHard dry: 12 hours

Minimun: 10 hoursMaximum with itself : none

12 Hours * 5 Days

30°CTouch dry: 0.75 hours

Hard dry: 9 hoursMinimun: 8 hours

Maximum with itself : none8 Hours * 3 Days

* Mentioned maximum overcoat intervals is for Seajet 117 - Seajet 011. Maximum overcoat interval of Seajet 117 with itself is free


SEAJET 017

SEAJET 117


35



[email protected]



Drying Times - Antifouling



Pot Life Remarks

5°CSurface dry: 3 hoursHard dry: 12 hours


- 24 hours

10°CSurface dry: 2 hours


Maximum with itself : None - 16 hours



Maximum with itself : None- 12 hours

30°CSurface dry: 30 mins





Pot Life Remarks



- 24 hours












Pot Life Remarks



- 24 hours










SEAJET 031

SEAJET 033

SEAJET 034


36



[email protected]






Pot Life Remarks




10°CSurface dry: 30 minsHard dry: 4.5 hours


- 10 hours







TemperatureDrying Time

(at DFT 150 µ)Overcoating Intervals

(at DFT 150 µ)Pot Life Remarks



36 hours 24 hours



Maximum with itself : None 36 hours 18 hours



Maximum with itself : None36 hours 12 hours



Maximum with itself : None36 hours 10 hours

SEAJET 039

SEAJET 037


37



[email protected]



Drying Times - Topcoats



Pot Life Remarks

5°C - -

10°C - -


Minimun: 24 hours- *

30°C - -

* If overcoating intervals are exceeded, sand with wet or dry nr. 320 abrasive paper



Pot Life Remarks

5°C - -

10°C - -



6 hours *

30°C - -

* After 48 hours light sanding with abrasive paper nr. 360 is recommended

SEAJET 122

SEAJET 132

Drying Times - Topcoats

38



[email protected]



Drying Times - Varnish



Pot Life Remarks

5°C - -

10°C - -



- -

30°C - -



Pot Life Remarks

5°C - -

10°C - -



4 hours *

30°C - -

* After 48 hours light sanding with abrasive paper nr. 360 is recommended

SEAJET 120

SEAJET 130

Drying Times - Varnish

39



[email protected]



How much paint should I use?For the underwater system please check page number 52 ‘How much paint to use’. For the above water systems, please check the technical datasheets. The coverage rate is mentioned there.

When is a paint system in bad condition? In bad condition means when the paint system is showing blisters, cracks or is just peeling of.

When is a paint system in a good condition?In good condition means when the paint system is not showing blisters, cracks or is just peeling of.

During application of varnish, do I have to abrade between the layers?When the overcoating time is expended you have to abrade before applying the next coat (2-Component product). To get a glass-like finish we recommend abrading (P320-P400) between the layers.

How should I remove dust from the surface?For the underwater hull please wash the hull with fresh water and let it dry. For the topside, please use pressurized air and use a tack rack to remove all small dust particals.

What should I do when the overcoating interval has expired?Please abrade the surface with P180-P240 in all cases. After that you can follow the instructions onthe label.

How should I remove the existing paint system to the Epoxy coating or even the Gelcoat?To remove a complete paint system, please use abrasive paper or a chemical paint stripper. In some cases you can even blast the complete system off. Please use a professional blasting company. Please note that Antifouling should always be WET sanded.

How should I thin the Varnish to get a gloss finish?Seajet UV Varnish: 1st coat 50% Thinner U - 2nd coat 25% Thinner U - 3rd coat 10% Thinner U - 4th coat 0% Thinner U. In case where the existing coating is in a good condition, 2 coats are needed to make it look like new. Please use 0-10% thinner.

Is Seajet compatible with my existing Antifouling?The good news is that Seajet Antifouling and underwater coatings are compatible with practically all types of Antifouling. We recommend to use coat of SEAJET 011 on unknown systems or for the over coating on hard or insoluble Antifouling from the matrix type. Teflon based Antifouling can be over coated, except VC17M, this has to be removed completely.

Which preparation is required?Briefly – on the underwater hull, the existing paint and possible bare primer must be light wet sanded. Apply touch-ups with recommended primer. Check if the applied paint is compatible with the existing Antifouling, sometimes a sealer coat of Seajet 011 is required. Above the waterline, sand until the surface is matt and remove dust before you apply Seajet Varnish or Seajet Brilliance Topcoat. Read the detailedinstructions for more information.

FAQ’s

40



[email protected]



Seaj

et C

olou

r Car

d

41



[email protected]


The COPPERSHIELD 2000 Resin & Hardener should be stored in a warm, dry environment with an ambient Temperature of 15°C.

This copper rich, water miscible epoxy system provides excellent long-term resistance to marine growth when applied to the underwater section of G.R.P., wooden, ferro-cement, aluminium and steel boats. The standard pack consists of 0.5kg of both resin and hardener and 2.0kg of pure copper powder. With the three components thoroughly mixed together a total volume of 1.2 litres is produced and, when applied to a hull by brush or roller, the filled epoxy produces a hard, smooth, durable coating when fully cured. The COPPERSHIELD 2000 resin & hardener should be stored in a warm, dry environment with an ambient temperature of 15°C.

COPPERSHIELD 2000 is not an osmosis treatment in its own right, but can be done in conjunction with a West System osmosis treatment.

SURFACE PREPARATIONIt is important that thorough surface preparation is undertaken to enable any epoxy to develop its maximum properties. The basic requirement is that the hull surface is clean, dry and thoroughly abraded after removing previous surface coatings e.g. paint, anti-fouling, varnish and any other hull coatings. Any contamination such as oil, grease, wax or mould release must be removed before sanding by wiping the surface with an aggressive solvent such as WEST SYSTEM 850 or clean acetone and then wiping with clean, dry paper towels before the solvent dries. The recommended preparation for specific hull surfaces is detailed below.

a) GRP Hulls - The bare surface of the GRP must be scrupulously abraded (after all existing coatings have been removed) with 80 grit paper to achieve a mat surface. After abrading, remove the dust and debris with a vacuum cleaner or wipe the surface with a clean dry cloth or paper towel. Apply one primer coat of WEST SYSTEM 105 Resin/205 or 206 Hardener.

b) Wooden Hulls - If the boat has not been treated with an epoxy then abrade back to bare wood using 80/100 grit paper; remove the sanding dust and wipe clean the surface with a clean dry cloth or paper towel. Apply at least three coats of WEST SYSTEM epoxy (105 Resin/205 or 206 Hardener)to the hull. Refer to WEST SYSTEM technical literature for handling and application instructions. Allow the first coat of epoxy to fully cure and sand fair with 120 grit paper. Remove the sanding dust before applying the second coat. As soon as this coat of epoxy becomes “tacky” to the touch -dependent upon temperature, but normally between 2 and 4 hours, apply the third coat. If necessary, apply additional epoxy coats in a similar manner. If the boat has been previously coated with epoxy, abrade with 120 grit paper, remove the dust and debris and clean the surface with a clean dry cloth or paper towel. Apply one primer coat of WEST SYSTEM epoxy.

c) Steel Hulls - Ideally, steel hulls should be degreased and then blast cleaned to SA 21/2 but, if this is not possible, it must be thoroughly abraded with 60/80 grit paper. Immediately after cleaning, all dust and debris must be removed and WEST SYSTEM epoxy must be applied to the clean steel surface within 1 hour of blasting/ abrading to minimise oxidation of the surface and the onset of corrosion. Allow this coat to fully cure before sanding fair with 120 grit paper and applying a second coat. This serves as the primer coat prior to the application of COPPERSHIELD 2000.

Coppershield Process

HINTS & TIPS - COPPERSHIELD

42



[email protected]


d) Aluminium Hulls - The surface must be well abraded using 60/80 grit paper and degreased. If practical, a light blasting is an alternative preparation technique. Ensure the surfaces are immediately cleaned with WEST SYSTEM 850 solvent or clean acetone and then thoroughly dried to minimise oxidation. It is most important to apply the WEST SYSTEM 105/205 or 206 epoxy within 30 minutes after cleaning to minimise problems with oxidation and corrosion of the surface. When this coating has fully cured, sand fair with 120 grit paper and apply a second coat of WEST SYSTEM epoxy. This acts as the primer coat prior to the application of COPPERSHIELD 2000.

e) Ferrocement Hulls - Unsound concrete must be cut back to uncover sound material. All loose material must be removed by brushing or blowing lightly with compressed air and the surfaces thoroughly washed. If the surfaces are contaminated, scrub with detergent solution. Remove laitence and/or previous surface coatings with a wire-brush or by grit blasting. Ensure the surfaces are dry and sound before applying the priming coat of WEST SYSTEM 105/205 or 206 epoxy. When this application is fully cured, sand fair and apply a second coat. Full specification on epoxy treatment of ferrocement hulls is available on request.Applications may vary depending on the age/condition of the hull.

MIXING THE EPOXYa) Thoroughly mix WEST SYSTEM 105 Resin and either 205 or 206 Hardener after proportioning the two components in the ratio of 5 parts by weight of resin: 1 part by weight of hardener. The mixed epoxy can be applied to the hull with roller or brush. Because of the exothermic reaction of WEST SYSTEM epoxy, it is recommended that batch sizes of resin/hardener mixes do not exceed 300g. (250g resin: 50g hardener). When using the calibrated WEST SYSTEM Pumps, this equates approximately to a maximum of 8 full depressions of both resin and hardener pumps.

b) COPPERSHIELD 2000 epoxy. The resin & hardener is supplied in pre-weighed quantities (0.5kg of eachcomponent) and prior to application these two components should be warmed to approximately 20-25°C. This will aid dispersion of the copper powder and increase coverage. Blend the contents of the two containers and thoroughly mix the composition before slowly adding the copper powder and continue mixing until all the powder is incorporated into the epoxy. If using COPPERSHIELD 2000 epoxy for the first time, it may be beneficial to blend half the contents of the two containers (resin and hardener) with half the copper content. By reducing the batch size in this way provides a longer working/application time until some familiarity/expertise is built up.

The mixed system has a pot life of approximately 1-hour at 18 °C and must be used immediately after the mixing operation, because the copper powder will tend to settle in the mix, it is recommended that the epoxy be stirred occasionally during the application of each batch.

*NOTE: For mixing smaller quantities ensure that the correct resin/hardener/copper ratios are maintained as below:

• 1 part by weight of resin: 1 part by weight of hardener• 1 part by weight of resin/hardener mix: 2 parts by weight of copper powder


43



[email protected]


APPLICATIONAllow the final coat of WEST SYSTEM epoxy to become soft to the touch but no longer tacky, before applying the first coat of COPPERSHIELD 2000.This application can normally take place within 1-3 hours of the application of the WEST SYSTEM epoxy, dependent on temperature. We do not recommend the use of other epoxies as a primer as those products may not be compatible with Coppershield 2000. Contact Marine & Industrial for further information.

NOTE: If it is still possible to make an impression with your thumbnail, the WEST SYSTEM epoxy coating is not hard enough to sand and can still be coated without sanding. As a general time guide, if a period greater than 5 hours elapses between coating applications at room temperature (18 °C) or if the surface feels waxy, allow the epoxy to cure overnight and then wash with WEST SYSTEM 855 cleaning solution followed by a further wash with fresh water. Dry the surface thoroughly and then sand before over coating with COPPERSHIELD 2000.

When applying at temperatures below 18 °C, COPPERSHIELD 2000 will be more difficult to apply andmay cause “runs “in the coating. We recommend applying COPPERSHIELD 2000 in a warm dry environment and these conditions can be achieved by tenting the hull and providing dry heat, such as a fan heater, to ensure good circulation of warm air. To achieve the ideal conditions during application, the humidity must be below 60%. By warming the resin and hardener to 20°C/25 °C and applying the mix at temperatures above 18 °C, it is easier to achieve thin even coats of COPPERSHIELD 2000.

NOTE: To eliminate any settlement of the copper powder, regularly stir the mix thoroughly, say at 10 minute intervals. When applying by roller, dispense small quantities from the mixing pot to the roller tray. This will again ensure the copper does not settle in the roller tray.

primer coat exceeds 4 hour over coating time, leave for at least 24 hrs abrade and repeat primer coat aspreviously described. If Coppershield 2000 over coating time exceeded, leave for up to 72 hrs to allow full cure of the epoxy prior to sanding. Depending on the ambient temperature this may be less. Contact our technical department if any queries on this point. DO NOT SAND EPOXY THAT IS NOT FULLY CURED.

COPPERSHIELD 2000 can be applied by brush, roller or spray* and best results are achieved when the epoxy is warmed and the surface is at room temperature. If applied uniformly, a coverage rate of 8m2 per litre or 9- 10m2 per 3Kg (1.2 Litre) pack can be achieved. When applying the first coat, it is often possible to see the hull surface through the coating. Complete coverage can only be obtained by the application of further coats. Normally, three coats are applied to provide many years of resistance to marine growth. It is easier to apply the filled epoxy mix in thin, even coats rather than in heavy applications which are more difficult to ‘work’ and which will ‘run’ or ‘curtain’.

NOTE: In the vast majority of cases, the COPPERSHIELD 2000 is applied with a roller or brush and, to achieve a consistent coat thickness, it is recommended that each application of the epoxy is “tipped off’ using a small section of a roller cover. This technique is detailed in the WEST SYSTEM Technical Manual.

The first coating of COPPERSHIELD 2000 must be allowed to cure for at least 4 hours at room temperature (18°C) before the application of the second coat. The hull may be left for 12 hours at this temperature before applying additional coats but if left for a longer period the surface must be abraded.


44



[email protected]


When the final coat is fully cured and is hard enough to sand easily, a minimum of 72 hours after application, the surface should be lightly abraded to expose the copper. A 120 “wet & dry”grit is recommended for this purpose. The boat can be returned to the water after a period of 7 days from completion of application.

Note: dependent upon the type and extent of marine growth in the waters in which the boat is to be sailed, abrasion of the Coppershield coating to expose the copper particles may not be necessary. It may be worthwhile sailing the boat for a short season without abrading the final application – any fouling after one season will be light, can easily be washed and the Coppershield coating then abraded to provide future protection from marine growth.


Over Coating Time:Stage Product Min Max

Primer Coat West System 105/205 or 206 2 Hours 4 Hours1st Coat Coppershield 2000 4 Hours 12 Hours2nd Coat Coppershield 2000 4 Hours 12 Hours3rd Coat Coppershield 2000 4 Hours 12 HoursLaunch Time - 7 days -

IMPORTANT OVERCOATING INFORMATION (Data based at 20°C)

45



[email protected]


HINTS & TIPS - JOTUN

It is important to identify the ideal antifouling to fit with the existing paint system on the boat. There are three approaches to secure a correct choice:

1. If you know which anitifoul is currently applied on the boat, follow the compatibility table on page 18.

2. If the current antifouling is unknown, apply a sealing coat of Vinyl Primer prior to applying the antifouling

3. If the current paint system is damaged, remove coat by coat until a complete and undamaged coat is identified. (paint or original substrate). Sand the substrate and apply primer according to the recommended paint system for that particular substrate prior to applying the antifouling.

In order to choose the correct antifouling for your boat and usage, it is important to consider type of boat, usage frequency, geographic location, current antifouling, and whether the boat is frequently transported by trailer. Also keep in mind environmental aspects and local regulations.

Area of Use HardNon Stop MareNostrum

SPAqualine Opitma

Racing

Motot Boats PPP PP PP

Sailing Boats PPP PP PP

Regatta Sailing Boats PP P PPP*

Speed Boats (40 Knots+)

PP PP PPP

Aluminium & Light Metal Parts

PPP (White/Grey)

PP (White)

PPPPP

(White/Grey)

Propeller, Flaps, etc (not made from light metal)

High Fouling Areas PPP P PPP PP

Fresh Water Areas (Lakes)Key: PPP Excellent PP Good P Suitable* Jotun Yachting recommend wet sanding of the surface after application** Aqualine Opitma should not be applied on the hull

Self Polishing

Same antifouling as for the main hull or Aqualine Opitma**

Antifouling is normally not recommended for use in freshwater areas

Choose the Ideal Antifoul

46



[email protected]



Paint Systems

Fibreglass Aluminium Wood Steel Light Wight Metals

1. CleaningDegrease with Jotun thinner no.7 (Xylen)

2. Preparation Sanding with P120-P150 grade

Mechanical Sanding with P120-P180 grade

Mechanical Sanding with P120-P180 grade

3. Apply 5-15 x Clipper I

4. Apply 3 x Antipest 2 x Antipest 2 x Vinyl Primer2 x Epoxy Yacht

HB2 x Vinyl Primer

Spray5. Apply Anitpest

6. Apply 2 x Antifouling

2 x Antifouling NonStop White/

Grey, Racing White/ Grey,

Mare Nostrum SP White

2 x Antifouling 2 x Antifouling3 x Aqualine

Optima

High pressure fresh water and degrease if necessary

On old paint systems: wash thoroughly with fresh water before you start. If the current antifouling is unknown, you need to apply a sealer coat of Vinyl Primer to ensure adhesion. If the already applied antifouling is known, please consult the compatibility chart on page 18

Paint Systems

47



[email protected]



Antif

oulin

g

Prod

ucts

Area

of U

seCo

vera

ge

per c

oat

Clea

ning

Dryi

ng T

ime

23°C

15°C

10°

Colo

ur

Reco

atin

g in

terv

al:

8 ho

urs

10 h

ours

12 h

ours

Laun

chin

g tim

e m

in:

12 h

ours

16 h

ours

24 h

ours

Laun

chin

g tim

e m

ax*:

9 m

onth

s9

mon

ths

9 m

onth

s

Reco

atin

g in

terv

al:

8 ho

urs

10 h

ours

12 h

ours

Laun

chin

g tim

e m

in:

12 h

ours

16 h

ours

24 h

ours

Laun

chin

g tim

e m

ax*:

9 m

onth

s9

mon

ths

9 m

onth

s

Reco

atin

g in

terv

al:

8 ho

urs

10 h

ours

12 h

ours

Laun

chin

g tim

e m

in:

12 h

ours

16 h

ours

24 h

ours

Laun

chin

g tim

e m

ax*:

9 m

onth

s9

mon

ths

9 m

onth

s

Laun

chin

g tim

e m

in:

3 ho

urs

8 ho

urs

10 h

ours

Laun

chin

g tim

e m

ax*:

9 m

onth

s9

mon

ths

9 m

onth

s

10m

²/L

Jotu

n Th

inne

r N

o.7

(Xyl

ene)

Blac

k, D

ark

Blue

, Re

d, W

hite

Aqua

line

Opt

ima

- A n

ew

gene

ratio

n of

per

fect

ion

for

driv

es a

nd o

ther

ligh

t-m

etal

co

mpo

nent

s bel

ow th

e w

ater

line.

An

outs

tand

ing

effe

ct

agai

nst f

oulin

g th

roug

hout

the

entir

e se

ason

For d

rives

, pro

pelle

rs, f

laps

and

ot

her l

ight

-met

al c

ompo

nent

s be

low

the

wat

erlin

e. It

is

impo

rtan

t tha

t the

surf

ace

is cl

ean

and

degr

ease

d (u

sing

Jotu

n Th

inne

r No.

7) p

rior t

o ap

plic

atio

n of

Vin

yl P

rimer

and

Aq

ualin

e O

ptim

a.

10m

²/L

Jotu

n Th

inne

r N

o.7

(Xyl

ene)

Blac

k, G

rey

Appl

y 2-

3 co

ats w

ith 1

5-20

min

utes

inte

rval

Blac

k, G

rey,

W

hite

, Dar

k Bl

ue,

Blue

, Red

RACI

NG

- Ad

vanc

ed h

ard

antif

oul t

hat p

rovi

des a

har

d,

smoo

th a

nd p

olish

able

surf

ace.

N

o Ch

alki

ng

Can

be u

sed

on m

ost t

ypes

of

boat

s, b

ut sp

ecia

lly d

evel

oped

fo

r spe

ed b

oats

(40

knot

s +).

Onl

y w

hite

and

gre

y co

lour

s are

re

com

men

ded

for a

lum

iniu

m

hulls

10m

²/L

Jotu

n Th

inne

r N

o.7

(Xyl

ene)

Blac

k, G

rey,

W

hite

, Dar

k Bl

ue,

Blue

, Red

NO

NST

OP

- Ver

y ef

ficie

nt, t

op-

clas

s sel

f pol

ishin

g an

tifou

ling

prod

uct,

base

d on

adv

ance

d hy

drat

ing

bind

ers,

ass

urin

g an

ac

tive

surf

ace

whi

ch is

co

ntin

uous

ly re

new

ed

For a

ll ty

pes o

f boa

ts, p

rovi

ding

an

d ex

celle

nt re

sult

thro

ugho

ut

the

entir

e se

ason

. Onl

y w

hite

an

d gr

ey c

olou

rs a

re

reco

mm

ende

d fo

r alu

min

ium

hu

lls

10m

²/L

Jotu

n Th

inne

r N

o.7

(Xyl

ene)

Mar

e N

ostr

um S

P - E

ffici

ent s

elf

polis

hing

ant

ifoul

ing

base

d on

sp

ecia

l bin

ders

, ass

urin

g an

ac

tive

surf

ace

For a

ll ty

pes o

f boa

ts, p

rovi

ding

a

good

resu

lt. O

nly

whi

te c

olou

r is

reco

mm

ende

d fo

r alu

min

ium

hu

lls

Ant

ifoul

48



[email protected]



Compatibility Chart

Hard Antifoulings

NonStop Mare Nostrum SP Racing

NonStop, Mare Nostrum SP, other

Selfpolishing Antifoulings*

Apply Directly Apply Directly Apply Directly

Racing, other hard antifoulings*

Wet sand + new coat Wet sand + new coat Wet sand + new coat

Unknown Wet sand + Vinyl Primer Wet sand + Vinyl Primer Wet sand + Vinyl Primer

Apply Directly Apply directly once the surface is dry and clean

Wet sand + new coat

Wet sand + Vinyl Primer

Wet sand with a medium grade sand paper and rinse well with fresh water. Apply new coat once the surface is dry and cleanWet sand with a medium grade sand paper and rinse well with fresh water. Apply one sealer coat of Vinyl Primer.

New Antifouling

Selfpolishing AntifoulingsOld Antifouling in Good Condition

* Except Seajet 034, Hempel Glide Cruise, Hempel Glide Speed, International VC17 or antifouling or antifouling product containing teflon. A sealer coat of Vinyl Primer must be applied when overcoating these

Compatibility Chart

49



[email protected]



How much antifouling do I need?

Length (m) 4 6 7.5 9 11 13 15

Length (ft) 13 20 25 30 36 43 49

Area (m²) 8 12 20 24 34 60 73

Litres required 2 3 5 6 8.5 14 17

Cans 0.75L 3 4 7 8 12 19 23

Length (m) 4 6 7.5 9 11 13 15

Length (ft) 15 20 25 30 36 43 49

Area (m²) 6 9 14 22 34 40 50

Litres required 1.5 2.5 3.5 5.5 8.5 10 12.5

Cans 0.75L 2 4 5 8 12 14 17

Length (m) 6 7.5 9 11 13 15

Length (ft) 20 25 30 36 43 49

Area (m²) 13.5 21 28 38 60 75

Litres required 3.5 5.5 7 9.5 14 18

Cans 0.75L 5 8 10 13 19 24

Sailing Boat

Large Keel Boat

Preventing fouling is not just a question of the antifouling itself, but also the application and tickness of each coat. It is important to have enough paint for the surface to be paint, in order to achieve the correct protection.

The figures show paint consumption for two coats. This is only a guide, the accuracy will decrease as the size of the boat increases.

Motor Boat

How Much Antifoul Do I Need?

50



[email protected]



Jotun yachting and Megayacht Product coverage rates guide

This guide uses freely available data sheet information concerning average film thickness achievable and the volume solids of each product. This guide is provided in good faith for the use by professionals who understand the variables that can be experienced at each application of Jotun product and is not intended to be 100 % accurate for every application due to these variations, it is provided to act as a guide to assist

with potential costing and estimates.

All coverage rates are per square metre and per single coat at recommended film thickness, the total amount of coats that may suit each project or vessels specific requirements may vary.

Coverage rates for spray application are based on conventional spray equipment and have an allowance of 30% wastage for primers and antifoulings and 40 % wastage for topcoats built in.

The coverage rates for Brush and Roller application have a 10 % wastage built in. All coverage rates will vary depending on the equipment used, atmospheric conditions, addition of

solvents and working practices. To use this guide simply take the known surface area (m2) and divide by the shown coverage rate to give

required amount of liters.

Product Coverage (S) Coverage (B/R) WFT per coat (S) WFT per coat (B/R)

Megaprimer 3 m2/lt 4.3 m2/lt 230 microns (125 dft) 63 microns(34 dft)

Antipest 3.7 m2 lt 5.3 m2 lt 80 microns (35 dft) 40 microns(18 dft)

Megacoat 3.3 m2/lt 4.7 m2/lt 200 microns (145 dft) 100 microns (72 dft)

Megasealer 2.8 m2/lt 4.2 m2/lt 240 microns (150 dft) 120 microns (74 dft)

Megagloss HG 16 m2/lt 25 m2/lt 50 microns (26 dft) 25 microns (13 dft)

Megagloss AC 16 m2/lt 25 m2/lt 50 microns (30 dft) 25 microns (15 dft)

Vinyl Primer 3.3 m2/lt 4.7 m2/lt 200 microns (76 dft) 100 microns (38 dft)

Antifoulings 7 m2/lt 10 m2/lt 100 microns (52 dft) 50 microns (26 dft)

Trowel applied filler materials require 1 lt for every 1 m2 of area to be filled at 1mm deep Note : (s) = Spray application (B/R) = Brush and roller application

This guide uses freely available data sheet information concerning average film thickness achievable and the volume solids of each product. This guide is provided in good faith for the use by professionals who understand the variables that can be experienced at each application of Jotun product and is not intended to be 100 % accurate for every application due to these variations, it is provided to act as a guide to assist with potential costing and estimates.

All coverage rates are per square metre and per single coat at recommended film thickness, the total amount of coats that may suit each project or vessels specific requirements may vary.

Coverage rates for spray application are based on conventional spray equipment and have an allowance of 30% wastage for primers and antifoulings and 40 % wastage for topcoats built in. The coverage rates for Brush and Roller application have a 10 % wastage built in. All coverage rates will vary depending on the equipment used, atmospheric conditions, addition of solvents and working practices.

To use this guide simply take the known surface area (m2) and divide by the shown coverage rate to give required amount of liters.

Jotun Yachting and Megayacht Product Coverage Rates Guide

51



[email protected]



Spra

y Ti

p Re

com

men

dati

ons

for J

otun

Pri

mer

s w

ith

Gra

co S

pray

Equ

ipm

ent

Joto

mas

tic B

lack

87

Bel

ow W

LGr

aco

Muk

er A

ir As

sist

Grac

o M

uker

ES

Air A

ssist

Grac

o Pr

o Gr

avity

Grac

o Pr

o Su

ctio

nM

ixin

g Ra

tio6:

16:

16:

16:

1Vi

scoc

ity -

seco

nds/

din

455

5522

22Pa

int P

ress

ure

2700

2700

NA

NA

Air P

ress

ure

(psi)

1515

4545

Mic

rons

WFT

per

coa

t22

022

015

015

0Ti

p/N

ozzl

e si

ze41

241

21.

8mm

1.8m

m

Joto

mas

tic G

rey

87 A

bove

WL

Grac

o M

uker

Air

Assis

tGr

aco

Muk

er E

S Ai

r Ass

istGr

aco

Pro

Grav

ityGr

aco

Pro

Suct

ion

Mix

ing

Ratio

6:1

6:1

6:1

6:1

Visc

ocity

- se

cond

s/di

n 4

2424

2020

Pain

t Pre

ssur

e21

0021

00N

AN

AAi

r Pre

ssur

e (p

si)10

1040

40M

icro

ns W

FT p

er c

oat

150

150

125

125

Tip/

Noz

zle

size

412

412

1.8m

m1.

8mm

Jotu

n M

egaP

rimer

- G

rey

Grac

o M

uker

Air

Assis

tGr

aco

Muk

er E

S Ai

r Ass

istGr

aco

Pro

Grav

ityGr

aco

Pro

Suct

ion

Mix

ing

Ratio

4:1

4:1

4:1

4:1

Visc

ocity

- se

cond

s/di

n 4

3737

2020

Pain

t Pre

ssur

e21

0021

00N

AN

AAi

r Pre

ssur

e (p

si)10

1040

40M

icro

ns W

FT p

er c

oat

200

200

125

125

Tip/

Noz

zle

size

412

412

1.8m

m1.

8mm

Jotu

n An

ti-Pe

st P

rimer

Grac

o M

uker

Air

Assis

tGr

aco

Muk

er E

S Ai

r Ass

istGr

aco

Pro

Grav

ityGr

aco

Pro

Suct

ion

Mix

ing

Ratio

4:1

4:1

4:1

4:1

Visc

ocity

- se

cond

s/di

n 4

2828

1818

Pain

t Pre

ssur

e30

0030

00N

AN

AAi

r Pre

ssur

e (p

si)15

1545

45M

icro

ns W

FT p

er c

oat

100

100

8080

Tip/

Noz

zle

size

308

308

1.8m

m1.

8mm

52



[email protected]



Auriga White 9917 Lynx White 5097

Norma Cream 1399

Carina White 9901Ara White 0001Tucana White 6049 Aquila White 5096

Volans Cream 8273 Centaurus Cream 0789 Canis Yellow 1406 Sculptor Grey 1407Perseus Ochre 1400

Coma Cream 1386 Pictor Ochre 1879 Draco Red 2256 Cealum Red 3213Apus Red 3126Indus Red 2232

Cygus Blue 4188Hercules Blue 4187 Casiopeia Blue 4196Sagitta Blue 4032Leo Blue 4186

Aries Blue 5092

Antlia Blue 4471

Colours are for guidance only

Corona Green 7127Aquarius Blue 4630Lyra Blue 4427 Delphinus Grey 0967Orion Green 5251

Phoenix GreyPegasus Grey 5098Columba Grey 6045 Pyxis Black 0099Libra Grey 5099

Lupus Black 9957 *

* This Colour is not available in MCI. Please enquire for availibity and MOQ

JOTUN Colour Card

53



[email protected]


HINTS & TIPS - MARINE FINISH

Beige

Black

Bold Yellow Brunswick Green

Cream

Camouflage Grey

Dark Admirality Grey

Deep Cream

Deep Ming Blue

French Blue

Light Admirality Grey

Grey

Light French Blue

Mediterranean White Off White

Pale Blue Roundel Blue

Pale GreenGolden Yellow

Light Ivory

Lilac

Orchre Brown

Souvenirs Blue

Schwarzblau TelegreyColbolt Blue

Gloss

White

Undercoat

Ivory Pale GreyWhite


Marine Finish Colour Card

54



[email protected]


HINTS & TIPS - RYLARD

Rylard Finish Colour Card

Undercoat

Cream Grey Mid Blue Green Dark RedRed

Black White Magnolia Cream Golden YellowJasmine

Gloss

Pirate Red Signal Red Post Service Red Crimson MaroonMercedes Red

Silver Fox LBS Grey Monetego Anchusa Blue Nile BlueSmalt

Oxford Blue Navy Blue Royal Blue Eau De Nil DolphinMeadow Green

Yacht Green Union Canal Green B.R Green

Black White


Marine & IndustrialStation Road, Worstead, North Walsham, NR28 9RZ

Tel: 01692 406822 Fax: 01692 406866Email: [email protected] Web: marineindustrial.co.uk

Registration No. OC307087 VAT No. 451 3632 69

Available Catalogues......

Exceptional Service Since 1986 Issue 1.1 Paints & Coatings · It’s easy to apply with the best...

Documents

Transcript of Exceptional Service Since 1986 Issue 1.1 Paints & Coatings · It’s easy to apply with the best...