Evaluation Board Manual - fujitsu.com · 15 C6 Ceramic capacitor 630v 470pF, X7R, 1206...
Transcript of Evaluation Board Manual - fujitsu.com · 15 C6 Ceramic capacitor 630v 470pF, X7R, 1206...
MB39C601MB39C601--EVBEVB--CN01CN01
Evaluation Board ManualEvaluation Board Manual
3W Candle Lighting AC 220V 3W Candle Lighting AC 220V
MB39C601MB39C601--EVBEVB--CN01CN01
Rev 1.0
Mar. 2013
2. EVB Electrical Performance Specifications2. EVB Electrical Performance Specifications
1. Summarize1. Summarize
The driver MB39C601-EVB-CN01 has the driving capability of 3 watts. It can be
placed in LED candle light or other similar model
Ta = +25 , fac = 50Hz
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
Input Characteristics
Input Voltage Range 198 220 242 VAC
Maximum Input Current Vin=220Vac,50Hz,Pout=3W 20 mA
Output Characteristics load:6s1p
Output Voltage Output Current=170mA 18 V
Output Current 170 mA
Output Current Ripple Co=330uF 70 mAPP
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED
Pin Name Description
L AC line input
N AC line input
LED+ LED output (+)
LED- LED output (-)
3.Terminal Description3.Terminal Description3.Terminal Description3.Terminal Description3.Terminal Description3.Terminal Description3.Terminal Description3.Terminal Description
1
Output Current Ripple Co=330uF 70 mAPP
Systems Characteristics
Switching frequency 80 KHz
Efficiency Vin=220Vac,50H 75 %
Power Factor Vin=198Vac~242Vac,Pout=3W 0.93
PCB Size L*W*H 26*18.5*15 mm
Dimming Mode - Triac/No-triac -
Protection function OTP, OVP,
4. Test Setup4. Test Setup
(1) Recommended Test Setup
(Note)
This evaluation board is a high voltage. Should be handled carefully.
During operation, do not touch the evaluation board.
・Connect L and N to AC power.
・Please connect the measuring instrument and LED.(LED: 6LED series connected, VF = 3V, IF = 170mA)
AC Power SupplyVAC:220Vrms
DMMVOUT
+ -
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED
(2) How to check
• Make sure that the terminals are connected correctly, and then turn on the AC POWER.
• LED light ,and the same time VOUT = 23V, IOUT = 300mA .The EVB working properly.
DMMIOUT
+ -
2
5. PCB layout5. PCB layout
MB39C601MB39C601MB39C601MB39C601MB39C601MB39C601MB39C601MB39C601--------EVBEVBEVBEVBEVBEVBEVBEVB--------CN01CN01CN01CN01CN01CN01CN01CN01
Top view(top side) Top view (bottom side)
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED
Board Layout (top side)
3
Board Layout (bottom side))))
6. Schematic6. Schematic
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED4
7. BOM List7. BOM List
NOCOMPON
ENTDESCRIPTION PART No. MFR
1 U1 LED driver IC, SOP-8 MB39C601 Fujitsu
2 R6 Chip resistor, 5.1RΩ, ±5%,1/10W, 0603 RC0603JR-075R1L YAGEO
3 R11 Chip resistor, 33KΩ, ±1%,1/10W, 0603 RC0603FR-0733KL YAGEO
4 R13 Chip resistor, 43KΩ, ±1%,1/10W, 0603 RC0603FR-0743KL YAGEO
5 R3 Chip resistor, 110KΩ, ±1%,1/10W, 0603 RC0603FR-07110KL YAGEO
6 R4 Chip resistor, 200KΩ, ±5%,1/10W, 0603 RC0603JR-07200KL YAGEO
7 R12 Chip resistor, 360KΩ, ±1%,1/10W, 0603 RC0603FR-07360KL YAGEO
8 R7 Chip resistor, 3RΩ, ±5%,,1/8W, 0805 RC0805JR-073RL YAGEO
9 R5 Chip resistor, 75KΩ, ±5%,1/8W, 0805 RC0805JR-0775KL YAGEO
10 R1 Chip resistor, 1MΩ, ±5%,1/8W, 0805 RC0805JR-071ML YAGEO
11 R8 Chip resistor, 150KΩ, ±5%,1/4W, 1206 RC1206JR-07150KL YAGEO
Aluminum electrolytic capacitor,25V 330uF 105
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED5
12 C1Aluminum electrolytic capacitor,25V 330uF 105
8*12STD CHONG
13 C2Aluminum electrolytic capacitor,50V 10uF 105
4*12STD CHENGX
14 C9,C3,C8 Ceramic capacitor 50v 10nF, X7R, 0602 GRM188R71H103KA01D MuRata
15 C6 Ceramic capacitor 630v 470pF, X7R, 1206 GCM31A7U2J471JX01D MuRata
16 C4 Film polypropylone capacitor 4.7nF 630V CBB STD STD
17 D1 Diode Schottky 100V 1A,SMA SS110 MCC
18 D2 Ultra fast200mA 175V,SOT-23 MMBD1404 Fairchild
19 D3 Zener diode Glass 500mW, 18V, LL34 STD STD
20 D4 Ultra fast 800V 1A ,SMA STTH108A ST
21 BR1 Bridge rectifier,0.5A,600V,SO-4 MB6S Fairchild
22 Q1 N-mosfet,800V,3.8ohm,2.5A,IPAK STD3NK80 ST
23 T1Transformer Lp=1mH, Np: Ns:
Na=160T:27T:21TSTD BZD
8. Transformer Specification8. Transformer Specification
2, Primary windings inductance :Lp=1mH (100 KHz),Air gap in the column and
inductance value is1mH ±10%,Leakinginductance as small as possible.
winding instruction
NameWinding
start pin→end pin
Wire
Diameter ((((mm)))) Turns Wire
properties
Insulation
tape
Np-1(primary ) 1→20.12(Inner
diameter) 75
Ordinary
enameled
wire
3layers
Ns(secondary)10→9
0.28(Inner
diameter) 27
Ordinary
enameled
wire
3 layers
Na(auxiliary) 7→60.12 (Inner
diameter) 21
Ordinary
enameled
wire
3 layers
Np-2(primary) 2→3 0.12(Inner
75
Ordinary
enameled 3 layers
1, Magnetic core:EPC13 ,PC40,Bobbin 5pins+5 pins,horizontal type;
3, Sandwich winding, dipping, cut short 2pin, pull out or cut short 4pin、5pin、8pin
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED6/ 15
Np-2(primary) 2→3 diameter) 75 enameled
wire
3 layers
9. Property data9. Property data99--1 Efficiency1 Efficiency 99--2 Power Factor2 Power Factor
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
190 200 210 220 230 240
Co
nvers
ion
eff
icie
ncy
η
Input Voltage 50Hz Vac [V]
0.5
0.55
0.6
0.65
0.7
0.75
0.8
0.85
0.9
0.95
1
190 200 210 220 230 240
Po
wer
Facto
r P
F
Input Voltage 50Hz Vac [V]
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED6
99--3 Line regulation3 Line regulation
LLoadoad::6LEDs in series 6LEDs in series LLoadoad::6LEDs in series 6LEDs in series
LLoadoad::6LEDs in series 6LEDs in series
Input Voltage 50Hz Vac [V] Input Voltage 50Hz Vac [V]
0
20
40
60
80
100
120
140
160
180
200
190 200 210 220 230 240
Ou
tpu
t C
urr
en
t IL
ED
[m
A]
Input Voltage 50Hz Vac [V]
99--5 Output Ripple5 Output Ripple
VBULK
IOUT
99--6 Switching Waveform6 Switching Waveform
VAC=220V, 50Hz. LED =6 pcs in series
VSW(Q1 drain)
99--8 Turn8 Turn--Off WaveformOff Waveform99--7 Turn7 Turn--On WaveformOn Waveform
VBULKVBULK
IOUT
VOUT
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED
VDD VDD
99--9 LED Open Waveform9 LED Open Waveform
VSW(Q1 drain)
IOUTIOUT
IOUT
VOUTVOUT
VOUT
7VDD
Do not Open too long Do not short too long
10. Evaluation board picture10. Evaluation board picture
Top View Bottom View
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED9
Specifications are subject to change without notice. For further information please contact each office.
11. 11. Revision HistoryRevision History
Name Version Remark
MB39C601-EVB-CN01 Rev 1.0
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED
Specifications are subject to change without notice. For further information please contact each office.All Rights Reserved.All Rights Reserved.All Rights Reserved.All Rights Reserved.The contents of this document are subject to change without notice.Customers are advised to consult with sales representatives before ordering.The information, such as descriptions of function and application circuit examples, in this document are presented solely forthe purpose of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information.FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information.Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein.The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions.Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.The company names and brand names herein are the trademarks or registered trademarks of their respective owners.10
Copyright 2013 FUJITSU SEMICONDUCTOR LIMITED