EVAGLIDE CORD DRAWN TRACK - Evans Textiles · 2019-03-22 · 780020 (MASTER CARRIER OVERLAP ARM)...

1

TRACK MAKING

EVAGLIDE CORD DRAWN TRACK

Version 1.0

For more guides and videos visit www.evans-textiles.com/resources

2

Here to help

At Evans, we understand the importance of getting things right for you and your clients.

That’s why we’ve put together this easy to follow step-by-step guide to help make things

easier for you.

In this guide we’ll cover product types, assembly information and chronologically set out

the instructions on how to put the product together. The guide is part of the ‘Evans

Difference’ giving our customers expert support which is designed to be easy to follow

and hassle free.


3

STEP 1, TRACK TYPE: -

Check track colour.

780019A

STEP 2, TRACK SIZE: -

Cut Track to specified size.

STEP 3, CORD LENGTH: -

Check overall cord length including drop and cut.

IMAGE 1 (780025A TRAVERSE CORD)

STEP 4, CORD SIDE: -

Corded right side, Corded left side, Corded both.

MID STACK RIGHT OP MID STACK LEFT OP


4

STEP 5, CARRIER TYPE: - Check carrier type and feed in to the track as below, if the carriers are Easy

wave, Easy flex or Easy fold they must be an even number.

780001 OFFSET 783073 WHEELED RUNNERS

STEP 6, OVERLAP & UNDERLAP: - See below,

780020 (MASTER CARRIER OVERLAP ARM) 780021 (MASTER CARRIER UNDERLAP ARM) STD CARRIERS

STEP 7, ENDCAP TYPE: - Long end pulley for pairs of curtain, long and short pulley for single stack

curtain which the long pulley on the corded side.

780024 BOTH SIDES FOR A PAIR 780024 AND 781150 FOR LEFT OP 781150 AND 780024 FOR RIGHT OP

REVERSIBLE PULLEYS RETURN PULLEY SHORT


5

TRACK ASSEMBLEY MID STACK CURTAIN, RIGHT OP IF LEFT HAND OP WORK FROM THE LEFT

SIDE OF THE TRACK: - Once all components have been picked feed the cord through the cord holes,

the cord pulley (see image 1), then feed the cord in to the track ensuring it is in the cord channels

correctly (see image 2) and pull all the way to the other side of the track, once the cord is completely in

the track apply the double cord connector to the string furthest away from you and do not fasten (see

image 3)

IMAGE 1 (780024 PULLEY) IMAGE 2 IMAGE 3 (780022 CORD CONNECTOR)

Then feed cord connector in to the underlap and feed in to the track ensure the cord connector enters

the cord channel (see image 4, 5 and 6)

IMAGE 4 (780021 underlap) IMAGE 5 IMAGE 6

Once the underlap is in the track then feed on the carriers, ensure the carrier curves towards the flat

edge of the underlap ( see image 7). Then push on the (see image 8)

IMAGE 7 IMAGE 8


6

Then go to the opposite side of the track and apply a cord connector to the bottom cord and screw this

down in to place (see image 9, 10)

IMAGE 9 IMAGE 10

Then feed the cord through the right hand pulley (see image 11), then add a short cord connector DO

NOT SCREW DOWN (see image 12)

IMAGE 11 (780024) IMAGE 12 (780023 HALF CORD CONNECTOR)

Feed the first cord connector (see image 10) in to the overlap (see image 13) and feed the first half in

to the track. Then feed the cord through the back gap of the overlap and hold the cord connector in

place (see image 14), then push the overlap and the half cord connector in to the track ensuring the

cord connector goes in to the cord channel.

IMAGE 13 (780020 OVERLAP) IMAGE 14 IMAGE 15


7

Then feed in the carriers and push on the endcap (see image 16)

IMAGE 16

To set the cord drop choose your cord length and set this on the tape measure i.e. 20cm cord and line

the 20cm section on the tape with the end of the track (see image 17), make sure all the carriers,

overlap and underlap are pulled back in to the fully open position then pull the cord up through the

overlap see image 18, keep pulling until the end of the cord is lined up with the end of the tape (see

image 17)

IMAGE 17 IMAGE 18

Then screw down the first cord connector on the opposite site to the cord operation (see image 19), then

screw down the end pulley (see image 20)

IMAGE 19 IMAGE 20


8

Then move back to the cord side and screw down the end pulley (see image 21), then screw down the

cord connector in the overlap (see image 22). Before cutting the cord, test the track works by pulling

the cord in the control side unit the overlap underlap meet, then pull in the opposite direction until they

are back in the open position.

IMAGE 21 IMAGE 22

Once the track has been tested and works, cut the excess cord and leave it around 3-4 inches long (see

image 23), then use a lighter to burn the end of the cord and push it together with your fingers (see

image 24) be very carful not to burn your fingers.

IMAGE 23 IMAGE 24 IMAGE 25


9

TRACK ASSEMBLEY SINGLE STACK OR DUAL: - Once all components have been picked feed the cord

through the cord holes is the cord pulley (see image 1), then feed the cord in to the track ensuring it is in

the cord channels correctly (see image 2) and pull all the way to the other side of the track, once the

cord is completely in the track add the end cap (see image 3), then turn the track over and screw the

endcap in place (see image 4)

IMAGE 1 (781150 SMALL PULLEY) IMAGE 2 IMAGE 3

IMAGE 4

Then go to the opposite side of the track and apply a cord connector to the bottom corded and crew

this down in to place (see image 5, 6)

IMAGE 5 IMAGE 6


10

Feed the first cord connector (see image 5) in to the overlap (see image 7) and feed the first half in to

the track. Then feed the cord through the back gap of the overlap and hold the cord connector in place

(see image 8), then push the overlap and the half cord connector in to the track ensuring the cord

connector goes in to the cord channel.

IMAGE 7 (780020 OVERLAP) IMAGE 8 IMAGE 9

Then feed in the carriers and push on the endcap (see image 10)

IMAGE 10

To set the cord drop choose your cord length and set this on the tape measure i.e. 20cm cord and line

the 20cm section on the tape with the end of the track (see image 11), make sure all the carriers,

overlap and underlap are pulled back in to the fully open position then pull the cord up through the

overlap (see image 12), keep pulling until the end of the cord is lined up with the end of the tape (see

image 11)

IMAGE 11 IMAGE 12


11

Screw down the end pulley (see image 13), then screw down the cord connector in the overlap (see

image 14). Before cutting the cord test the track works by pulling the cord in the control side unit the

overlap underlap meet, then pull in the opposite direction until they are back in the open position.

IMAGE 13 IMAGE 14

Once the track has been tested and works cut the excess cord and leave it around 3-4 inches long (see

image 15), then use a lighter to burn the end of the cord and push it together with your fingers (see

image 16) be very carful not to burn your fingers.

IMAGE 15 IMAGE 16 IMAGE 17

BRACKET TYPE: - Check to see if this is top fixed brackets or wall fixed. If wall fix check the bracket

length.

780007 (STANDARD CEILING BRACKET) 783339 (CONCEALED CEILING BRACKET) 783012 (TOP FIX BRACKET WITH CAP)


12

780010 (3.5CM WALL BRACKET) 780011 (6CM BRACKET) 780012 (7.5CM BRACKET)

780013 (10CM BRACKET) 780014 (15CM DOUBLE BRACKET) 780015 (25CM TRIPLE BRACKET)

781022 (7-11CM ADJUSTABLE WALL BRACKET) 783997 (COVER CAP)


13

EASYFLEX, EASYWAVE, and EASYFOLD TAPE:

EASYFLEX AND EASYWAVE TAPE EASYFOLD TAPE 15.75CM

EASYFOLD TAPE (ORDINARY) 10.75CM EASYFOLD TAPE (XL) 15.75CM

***PLEASE NOTE ALL NOTES ALL CODES ABOVE ARE FOR WHITE TRACKS

IF COLOUR VARIES PLEASE SEE TEAM LEADER FOR GUIDANCE***


14

***BEFORE PAKCAGING TICK OFF EACH ITEM TO MAKE SURE NO STEPS

HAVE BEEN MISSED AND NO ITEMS ARE MISSING***

…and that’s it! You’re finished!

STEPS COMPLETE? Please tick

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6


15

Evan Textiles (Sales) Ltd, Helmet Street, Manchester, M1 2NT

Registered in England No. 6186585 Part of the Evans Group of Companies

EVAGLIDE CORD DRAWN TRACK - Evans Textiles · 2019-03-22 · 780020 (MASTER CARRIER OVERLAP ARM)...

Documents

Transcript of EVAGLIDE CORD DRAWN TRACK - Evans Textiles · 2019-03-22 · 780020 (MASTER CARRIER OVERLAP ARM)...