EV7110 S0 R0 - joulwatt.com€¦ · VIN1 1 EN1 1 EN2 C2 0805/0.1uF/16V10% C5 0805/0.1uF/16V10% VIN2...
Transcript of EV7110 S0 R0 - joulwatt.com€¦ · VIN1 1 EN1 1 EN2 C2 0805/0.1uF/16V10% C5 0805/0.1uF/16V10% VIN2...
EV7110_S0_R0
6A, 5.5V Low On-Resistance
Dual-Channel Load Switch Parameters Subject to ChangeParameters Subject to ChangeParameters Subject to ChangeParameters Subject to Change Without NoticeWithout NoticeWithout NoticeWithout Notice
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 1
Unauthorized Photocopy and Duplication Prohibited.
FEATURES
Operating Range : 0.8V ~ 5.5V
Low Quiescent Current
80uA (Both Channels)
60uA (Single Channels)
Low ON-Resistance
Integrated Dual-Channel
Up to 6A Maximum Load Current per channel
Low-voltage Enable Control
Externally Programmable Rise Time
Quick Output Discharge
Thermal Shutdown
Available in DFN14LB Package
APPLICATIONS
Portable computers
Tablet PCs
Consumer Electronics
Set-top Boxes and Residential Gateways
Telecom Systems
Solid-State Drives (SSD)
DESCRIPTION
JW7110 is a low on-resistance dual channel load
switch with programmable turn-on rise time. It
contains two n-channel MOSFETS that can
provide 6A maximum continuous current per
channel. Each channel can operate over an input
voltage range of 0.8V to 5.5V.
Each channel can be independently controlled by
a low-voltage control signal through EN1/EN2 pin.
In JW7110, a 200Ω load resistor is integrated for
quick output discharge when load switch is turned
off. The optional external capacitor connected to
SS1/SS2 is used for output slew rate control.
ELECTRICAL SPECIFICATIONS
Parameter Symbol Value Unit
VBIAS Voltage VBIAS 2.5-5.5 V
VEN Voltage EN1,EN2 2-5.5 V
Input Voltage VIN1,Vin2 0.8~5.5 V
Output Voltage VOUT1,VOUT2 VIN1,VIN2 V
Output Current IOUT 0~6 A
TYPICAL PERFORMANCE
EV7110_S0_R0 JoulWatt
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 2
Unauthorized Photocopy and Duplication Prohibited.
SCHEMATIC
BILL OF MATERIALS
Qty. Designator Value Description Package Manufacturer Manufacturer
P/N
3 C1,C6 1uF Ceramic capacitor
16V ,X7R
0805C
2 C3,C4 1nF Ceramic capacitor
16V ,X7R
0805C
2 C2, C5 0.1uF Ceramic capacitor
16V ,X7R
0805C
2 VIN 0.8V~5.5V TEST-Pole
2 VOUT Vin TEST-Pole
1 U1 JW7110 Load Switch SOT23-6 Joulwatt JW7110
1VOUT1
1
VIN1
C4 0805/1nF/16V10%
C3 0805/1nF/16V10%
VIN26
VBIAS4
EN13
VIN11
VIN12
VIN27
EN25
VOUT28
VOUT29
SS210
GND11
SS112
VOUT113
VOUT114
0
U1
JW7110
GND
1
VIN2
GND
GND GND
1VOUT2
GND
GND
SS1
SS2
VIN1
1
EN1
1
EN2
C2
0805/0.1uF/16V10%
C5
0805/0.1uF/16V10%
VIN2
EN1
EN2
VOUT2
VOUT1
C1
0805/1uF/16V10%
C6
0805//1uF/16V10%
GND
EV7110_S0_R0 JoulWatt
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 3
Unauthorized Photocopy and Duplication Prohibited.
PRINTED CIRCUIT BOARD LAYEROUT
Figure1————Top Layer
Figure2————Bottom Layer
Figure3————Silk Layer
QUICK START GUIDE
1. Connect the positive terminal and negative terminal of the load to VOUT1/VOUT2
and GND of EVB, respectively.
2. Connect a power supply between VBIAS and GND with the supply in “OFF” state.
Set the output voltage of the power supply to 2.5V-5.5V.
3. Connect a power supply between VIN1/VIN2 and GND with the supply in “OFF”
state. Set the output voltage of the power supply to 0.8V~VBIAS.
4. Connect a power supply between EN1/EN2 with the supply in “OFF” state. Set the
output voltage of the power supply to 1V-5.5V.
5. Turn on the power supply and the evaluation board starts operating in normal
condition.
6. For more information, please refer to the datasheet of JW7110.
EV7110_S0_R0 JoulWatt
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 4
Unauthorized Photocopy and Duplication Prohibited.
TYPICAL PERFORMANCE CHARACTERISTICS
At TA=25,CT=1000pF
Fig. 1 Turn-on Response Time
(VIN = 0.8 VBIAS = 2.5 V, CIN = 1 µF, L = 0.1 µF, RL = 10 ΩΩΩΩ) Fig.2. Turn-on Response Time
(VIN = 0.8 V, VBIAS = 5 V, CIN = 1 µF, CL = 0.1 µF, RL = 10 ΩΩΩΩ)
Fig. 3 Turn-on Response Time
(VIN = 2.5 VBIAS = 2.5 V, CIN = 1 µF, L = 0.1 µF, RL = 10 ΩΩΩΩ) Fig.4. Turn-on Response Time
(VIN = 5 V, VBIAS = 5 V, CIN = 1 µF, CL = 0.1 µF, RL = 10 ΩΩΩΩ)
Fig.5Turn-on Response Time
(VIN = 0.8V VBIAS = 2.5 CIN = 1 µF, CL = 0.1 µF, RL = 10 ΩΩΩΩ) Fig. 6Turn-off Response Time
(VIN = 0.8V, VBIAS = 5V, CIN = 1 µF CL = 0.1 µF, RL = 10 ΩΩΩΩ)
EV7110_S0_R0 JoulWatt
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 5
Unauthorized Photocopy and Duplication Prohibited.
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Fig.7 Turn-on Response Time
(VIN = 2.5 VBIAS = 2.5 CIN = 1 µF, CL = 0.1 µF, RL = 10 ΩΩΩΩ) Fig. 8 Turn-off Response Time
(VIN = 5V, VBIAS = 5V, CIN = 1 µF CL = 0.1 µF, RL = 10 ΩΩΩΩ) Parameter Measurement Information
Rise and fall times of the control signal is 100ns.
EV7110_S0_R0 JoulWatt
JW7110_S0_R0 Rev.0.1 JoulWatt Proprietary Information. Patent Protected. 6
Unauthorized Photocopy and Duplication Prohibited.
IMPORTANT NOTICE
Joulwatt Technology Inc. reserves the right to make modifications, enhancements, improvements,
corrections or other changes without further notice to this document and any product described herein. Any unauthorized redistribution or copy of this document for any purpose is strictly forbidden.
Joulwatt Technology Inc. does not warrant or accept any liability whatsoever in respect of any products
purchased through unauthorized sales channel.
CCooppyyrriigghhtt ©© 22001166JJWW77111100 IInnccoorrppoorraatteedd..
AAllll rriigghhttss aarree rreesseerrvveedd bbyy JJoouullwwaatttt TTeecchhnnoollooggyy IInncc..