ETSI EN 302-208
-
Upload
petersam67 -
Category
Business
-
view
1.257 -
download
12
Transcript of ETSI EN 302-208
1
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Sigurd Bolt Sørensen, Bolt ConsultVice - Chairman ETSI-ERM-TG34
ETSI, Sophia Antipolis, 25 May 2004
RFID Standards & Regulations
2
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Frequencies for RFID
- LF: 120 kHz to 135 kHz for inductive systems
- HF: 13.56 MHz for smart cards and labels- UHF: 433 MHz for low power, active tags- UHF: 863 to 870 MHz, 902 to 928 MHz and
950 to 956 MHz depending on country- µWave: 2.45 GHz for Industrial applications
3
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Regulatory Standards
Current three Generic ETSI Standards:
- EN 300 330: 9 kHz - 30 MHz
- EN 300 220: 25 MHz to 1 GHz
- EN 300 440: 1 GHz – 40 GHz
4
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Current Limitations at UHF in Europe
- RFID at UHF currently restricted to band 869.40 - 869.65 MHz
- Must comply with EN 300 220- Transmitted power < 500 mW e.r.p.- Duty cycle < 10%
Impossible restrictions for RFID at UHF
5
RFID and Telecommunication Services25th May 2004
DATA BASE forum
ETSI RFID Standard at UHF
EN 300 220 does not meet needs of RFID at UHF
Formation of TG 34 within ETSI to address the specific requirements of RFID industry
Design of new ETSI standard EN 302 208 to satisfy market for RFID at UHF
6
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Principle requirements
Draft ETSI standard EN 302 208 proposes the following:
Shared operation in band 865.0 – 868.0 MHz at transmit powers up to 2 W e.r.p.
Mandatory “listen before talk” function Operation in sub-bands of 200 kHz Power levels of 100 mW, 500 mW and 2 W e.r.p.
7
RFID and Telecommunication Services25th May 2004
DATA BASE forum
RF Power Limits at UHF
865.0MHz
868.0MHz
865.6MHz
867.6MHz
100 mW
2 W
500 mW
8
RFID and Telecommunication Services25th May 2004
DATA BASE forum
RFID Transmission Times
Mandatory listen time of >5 msec before each transmission
Maximum period of continuous transmission of 4 sec
Pause of 100 msec between repeated transmissions on same sub-band, ormove immediately to another vacant sub-band
9
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Scope of EN 302 208
The technical requirements of ETSI Standard EN 302 208 are based on inputs provided by RFID manufacturers throughout the entire standardisation process.
The standard will permit operation in Europe of product built in compliance with ISO 18000-6
The standard may not permit operation of some new systems that are currently under development
10
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Regulatory Issues
RFID classified as SRD meaning: Type approval only Operate within a shared band No protection Regulated by new Annex 11 of
ECC/ CEPT ERC/Rec 70-03
11
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Status of ETSI Standard EN 302 208
Predicted Milestones:
Approval of Regulation by ECC in April 04 Public Enquiry (PE) period ended
PE Resolution meeting completed in May 04
Expect approval for National Vote by June 04
Expect publication in OJ in Autumn 2004
12
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Status of ECC/CEPT Regulation
Predicted Milestones:
Draft Regulation as Annex 11 to ERC/Rec 70-03, first March 2004
Approved for Consultation April 2004 Expect final approval and publication
September/October 2004
13
RFID and Telecommunication Services25th May 2004
DATA BASE forum
Contact Details
Sigurd Bolt SørensenBolt Consult
Lindetoften 23
2630 Taastrup
Denmark
Tel: +45 52 68 08
Mob: +45 20 42 30 92