erzrze
-
Upload
charaf-eddine-elinani -
Category
Documents
-
view
213 -
download
0
description
Transcript of erzrze
AM-5280APPROVAL No. - NE D’APPROBATION
Page 1 of/de 6 Project/Projet:AP-AM-97-0039
Measurement Canada Mesures CanadaAn agency of Industry Canada Un Organisme d’Industrie Canada
NOTICE OF APPROVAL AVIS D’APPROBATION
Issued by statutory authority of the Minister ofIndustry for:
Émis en vertu du pouvoir statutaire du ministre del’Industrie pour:
TYPE OF DEVICE
Electronic Bench Scales
TYPE D’APPAREIL
Balance de table électronique
APPLICANT REQUÉRANT
Mettler-Toledo Inc.1150 Dearborn Drive
Worthington, Ohio, 43085USA
MANUFACTURER FABRICANT
Mettler-Toledo GmbhIm Langacher,
CH-8606 GreifenseeSwitzerland / Suisse
MODEL(S)/MODÈLE(S) RATING/ CLASSEMENT
PG*CG*GG*
Max: 210 g to/à 12100 g e: 0.01 g to/à 1 gMax: 510 g / 2550 ct e: 0.1 g / 0.1 ctMax: 4100 g e: 0.1 g
See table for specific models and capacities / Voir le tableau pourmodèles et capacités spécifiques.
Accuracy Class / Classe de précision: II
AM-5280APPROVAL No. - NE D’APPROBATION
Page 2 of/de 6 Project/Projet:AP-AM-97-0039
NOTE: This approval applies only to devices, thedesign, composition, construction and performance ofwhich are, in every material respect, identical to thatdescribed in the material submitted, and that aretypified by samples submitted by the applicant forevaluation for approval in accordance with sections 14and 15 of the Weights and Measures Regulations. Thefollowing is a summary of the principal features only.
REMARQUE: Cette approbation ne vise que lesappareils don’t la conception, la composition, laconstruction et le rendement sont identiques, en toutpoint, à ceux qui sont décrits dans la documentationreçue et pour lesquels des échantillons représentatifsont été fournis par le recurrent aux fins d’évaluation,conformément aux articles 14 et 15 du Règlement surles poids et mesures. Ce qui suit est une brèvedescription de leurs principales caractéristiques.
SUMMARY DESCRIPTION: DESCRIPTION SOMMAIRE:
CATEGORY
The device is an electronic portable bench scale(balance).
CATÉGORIE
Il s’agit d’une balance de table électronique portable.
DESCRIPTION
The approved device is a self-contained electronicbalance, that is fitted with a single centrally locatedweight sensor, working on the electromagnetic forcecompensation principle. The weight sensor supportsa stainless steel load receiving element. The devicecomponents are encased within an aluminum housingwhich is supported by three (3) feet, one fixed (orstationary) in the front center of the device and two(2) adjustable in each rear corner. The device can befitted with a draft shield and is powered by a 12 VDCfrom a 100 VAC external transformer.
DESCRIPTION
Il s’agit d’une balance électronique autonome, munied’un capteur pondéral unique central, qui fonctionnesur le principe de compensation de la forceélectromagnétique. Sur le capteur pondéral repose unélément récepteur de charge en acier inoxydable. Lescomposants de l’appareil sont compris dans un boîtieren aluminium qui est soutenu par trois (3) pieds dontl’un, situé à l’avant au centre, est fixe (immobile) etles deux (2) autres, à chacun des coins à l’arrière, sontréglables. L’appareil est alimenté par 12 V c.c.provenant d’un transformateur externe de 100 V c.a.et peut être équipé d’un écran contre les courantsd’air.
DISPLAY
The device features a vacuum flourescent indicatorfor weight display, alphabetic messages, delta rangegraphic, weighing ranges, delta range for finerreadability and annunciators for among others,motion, cal, load, done, and abort.
DISPOSITIF D’AFFICHAGE
L’appareil comprend un indicateur fluorescent sousvide pour l’affichage du poids, des messagesalphabétiques, du graphique de la plage delta, desétendues de pesage, de la plage delta pour unelisibilité accrue ainsi que des voyants indiquant, entreautres, le mouvement, l’étalonnage, la charge et la finet l’abandon de l’opération.
AM-5280APPROVAL No. - NE D’APPROBATION
Page 3 of/de 6 Project/Projet:AP-AM-97-0039
FUNCTION KEYS
The device is fitted with the following keys:
“ON/OFF”, “TARE”, “e”, “v0w cal”, “F” and“Menu”.
TOUCHES FONCTION
L’appareil est muni des touches suivantes:
«ON/OFF», «TARE», «e», «v0w cal», «F» et«Menu».
Note that the zero and tare key functions (O/T) aresynonymous with these devices.
Il convient de remarquer que les fonctions du zéro etde la tare (O/T) sont synonymes sur ces appareils.
CALIBRATION
The device can be calibrated automatically with abuilt-in calibrated weight. In this mode, the balancewill perform an automatic calibration sequence whenneeded. During this automatic calibration sequencethe display will show the words “CAL”. When thissequence is complete, the device will return to normaloperation.
ÉTALONNAGE
L'appareil peut être étalonné automatiquement à l'aided'un poids d'étalonnage intégré. Dans ce mode, labalance effectue une séquence d’étalonnageautomatique si nécessaire. Pendant la séquenced’étalonnage automatique, l’afficheur indique le mot«CAL». Lorsque la séquence est terminée, l’appareilretourne en mode de fonctionnement normal.
SEALING
The scale can be sealed with a wire security sealthreaded through a hole in the top and bottom halvesof the rear of the enclosure preventing the housingfrom being separated. It is also necessary to place aself-destructive seal over one of the screws under thesub-platter to prevent access to calibration andconfiguration parameters.
SCELLEMENT
La balance peut être scellée à l’aide d’un filmétallique passé à travers un trou dans les moitiéssupérieure et inférieure de l’arrière du boîtierempêchant celui-ci d’être séparé. Il est égalementnécessaire de placer un scellé autodestructeur au-dessus d’une des vis sous le sous-plateau pourempêcher l’accès à l’étalonnage et à la configurationdes paramètres.
SERIAL CONNECTIONS
Standard design RS232C
CONNEXIONS SÉRIE
RS232C de conception standard
TEMPERATURE RANGE
The device is approved for use within a temperaturerange of 5°C to 40°C.
PLAGE DES TEMPÉRATURES
L’appareil est approuvé pour une utilisation àl’intérieur d’une plage de températures allant de 5°Cà 40°C.
AM-5280APPROVAL No. - NE D’APPROBATION
Page 4 of/de 6 Project/Projet:AP-AM-97-0039
Models, Capacities, Verification Scales Intervals and Platter SizesModèles, capacités, grandeurs de l’échelons de vérification et dimension des plateaux
Models/Modèles Max e d Platter/Plateau
PG203-S 210 g 10 mg 1 mg 128 mm x/sur 128 mmPG503-S 510 g 10 mg 1 mg 128 mm x/sur 128 mmPG503-SDR 100 g and/et 510 g 10 mg 1 mg to/à 10 mg 128 mm x/sur 128 mmPG802-S 810 g 0.1 g 0.01 g 165 mm x/sur 165 mmPG2002-S 2100 g 0.1 g 0.01 g 165 mm x/sur
165 mmPG3001-S 3100 g 0.1 g 0.1 g 165 mm x/sur
165 mmPG5002-S 5100 g 0.1 g 0.01 g 165 mm x/sur
165 mmPG5002-SDR 1000 g and/et 5100 g 0.1 g 0.01 g to/à 0.1 g 165 mm x/sur 165 mmPG5001-S 5100 g 1 g 0.1 g 240 mm x/sur
240 mmPG8000-S 8100 g 1 g 1 g 240 mm x/sur
240 mmPG8001-S 8100 g 1 g 0.1 g 240 mm x/sur
240 mmPG12001-S 12100 g 1 g 0.1 g 240 mm x/sur 240 mmPG12001-SDR 2400 g and/et 12100 g 1 g 0.1 g to/à 1 g 240 mm x/sur 240 mmPG12000-S 12100 g 1 g 1 g 240 mm x/sur 240 mmCG2502-S 2550 ct 0.1 ct 0.01 ct 165 mm x/sur 165 mm
510 g 0.1 g 0.01 g 165 mm x/sur 165 mmGG4002-S 4100 g 0.1 g 0.01 g 165 mm x/sur
165 mmGG4002-SDR 800 g and/et 4100 g 0.1 g 0.01 g to/à 0.1 g 165 mm x/sur 165 mm
Suffix “DR”: Delta-Range: The displayed division“d” changes at the lower capacity listed for themodel. The verification division “e” remainsconstant.
Suffixe “DR”: Delta-Range: L’échelon affiché “d”change lorsqu’il est à la capacité la plus bassementionnée pour le modèle. L’échelon de vérification“e” demeure constant.
EVALUATED BY
Milton G. SmithComplex Approvals ExaminerTel: (613) 952-0656Fax: (613) 952-1754
Tested by NTEP.
AM-5280APPROVAL No. - NE D’APPROBATION
Page 5 of/de 6 Project/Projet:AP-AM-97-0039
ÉVALUÉ PAR
Milton G. SmithExaminateur d’approbations complexesTéléphone: (613) 952-0656Télécopieur: (613) 952-1754
Testé par NTEP.
AM-5280APPROVAL No. - NE D’APPROBATION
Page 6 of/de 6 Project/Projet:AP-AM-97-0039
128 mm x/sur 128 mm Platter / plateau
165 mm x/sur 165 mm Platter / plateau
240 mm x/sur 240 mm Platter / plateau
AM-5280APPROVAL No. - NE D’APPROBATION
Page 7 of/de 6 Project/Projet:AP-AM-97-0039
APPROVAL:
The design, composition, construction andperformance of the device type(s) identified hereinhave been evaluated in accordance with regulationsand specifications established under the Weights andMeasures Act. Approval is hereby grantedaccordingly pursuant to subsection 3(1) of the saidAct.
APPROBATION:
La conception, la composition, la construction et lerenewment du(des) type(s) d’appareils identifié(s) ci-dessus, ayant fait l’objet d’une évaluationconformément au Règlement et aux prescriptionsétablis aux termes de la Loi sur les poids et mesures,la présente approbation est accordée en application duparagraphe 3(1) de la dite Loi.
The marking, installation and manner of use of tradedevices are subject to inspection in accordance withregulations and specifications established under theWeights and Measures Act. Requirements relating tomarking are set forth in sections 49 to 54 of theSpecifications Relating to Non-Automatic WeighingDevices. Installation and use requirements are setforth in sections 55 to 67 of the SpecificationsRelating to Non-Automatic Weighing Devices. Averification of conformity is required in addition tothis approval. Inquiries regarding inspection andverification should be addressed to the localinspection office of Industry Canada.
Le marquage, l'installation, et l'utilisationcommerciales des appareils sont soumis à l'inspectionconformément au Règlement et aux prescriptionsétablis aux termes de la Loi sur les poids et mesures.Les exigences de marquages sont définies dans lesarticles 49 à 54 des normes applicables aux appareilsde pesage à fonctionnement non automatique. Lesexigences d'installation et d'utilisation sont définiesdans les articles 55 à 67 des normes applicables auxappareils de pesage à fonctionnement nonautomatique. Une vérification de conformité estrequise. Toute question sur l'inspection et lavérification de conformité doit être adressée aubureau local d'Industrie Canada.
Original copy signed by:
René Magnan, P. EngDirectorApproval Services Laboratory
Copie authentique signée par:
René Magnan, ing.DirecteurLaboratoire des services d’approbation
Date: MAR 31 1999
Web Site Address / Adresse du site internet:http://mc.ic.gc.ca