EOBD2 User Manual - FG Technology · FG Technology 6/63 EOBD2 User Manual Se appare il seguente...
Transcript of EOBD2 User Manual - FG Technology · FG Technology 6/63 EOBD2 User Manual Se appare il seguente...
FG Technology 1/63 EOBD2 User Manual
EOBD2 User Manual
Index
Requisiti minimi – Minimum requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installazione software EOBD2 - Software Installation EOBD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Windows XP Installazione driver / Driver installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Windows 7-8-8.1-10 Installazione driver / Driver installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Windows 8 - Driver non certificato / Driver not signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Windows 8.1 - Driver non certificato / Driver not signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Windows 10 - Driver non certificato / Driver not signed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Compatibilità / Compatibility Windows XP in Windows Vista - 7 - 8 - 8.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Impostazione account / Account settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Impostazione Windows Firewall / Settings Windows Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FGTech_UPDATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Gestione licenze - Licence management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
LOG File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SLAVE istruzioni Crypt&Decrypt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
HARDWARE
Kit EOBD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Alimentazione / Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Adattatori/Adapter Standard - Volvo/Renault Truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Versione del manuale / Manual version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FG Technology 2/63 EOBD2 User Manual
REQUISITI MINIMI – MINIMUM REQUIREMENTS
Requisiti minimi consigliati:
- Processore Intel i5
- RAM 4GB
Per il corretto funzionamento del software è molto
importante fare attenzione alla percentuale di utilizzo
della CPU del computer che non deve essere superiore al
20% all’avvio del software EOBD2.exe.
Andare sul task manager cliccando il tasto destro
del mouse sulla barra della applicazioni e poi
Avvia Gestione Attività:
Recommended minimum requirements:
- Processor Intel i5
- RAM 4GB
For proper operation of the software it is very
important to pay attention to the percentage of the
CPU of the computer that it must not be greater
than 20% at startup EOBD2.exe the software.
Go to the Task Manager by right-clicking
mouse on the taskbar and then Task Manager:
Ora si può vedere lo stato della CPU:
Now you can view the status CPU :
Se la percentuale di utilizzo della CPU
è superiore al 20%, il corretto avviamento
e funzionamento del software non è garantito!.
If the percentage of CPU usage is more than
20%, the start and the operation of the
program is not guaranteed!
ATTENZIONE:
NON INSTALLARE il software se nel
computer sono installati programmi e
driver di cloni:
rischio danneggiamento interfaccia!
Formattare prima il PC!
ATTENTION:
DON’T INSTALL the software if in your
pc there is software or driver of clones
installed:
Risk of damaging the tool!
Format the PC before!
FG Technology 3/63 EOBD2 User Manual
Installazione software EOBD2 - Software Installation EOBD2
Guarda il video su Youtube per l’installazione:
https://www.youtube.com/watch?v=1YGD0zzR_sQ
Andare su www.fgtechnology.eu e nell’area
Download scaricare il file
Setup.exe (PRIMA INSTALLAZIONE)
Watch video on Youtube for installation:
https://www.youtube.com/watch?v=1YGD0zzR_sQ
In the web site www.fgtechnology.eu you can
download in the download area the file
Setup.exe (FIRST INSTALLATION)
Cliccare Next
Click Next
FG Technology 4/63 EOBD2 User Manual
Leggere attentamente le condizioni di contratto
e accettare i termini di licenza:
Read the conditions of contract attentively and
accept the terms of license:
Mantenere la cartella di installazione C:\FGTech
e cliccare Avanti
Maintain the folder of installation C:\FGTech
and click Next
FG Technology 5/63 EOBD2 User Manual
Cliccare Install Click Install
Attendere che l’installazione sia completata Wait that the installation has completed
FG Technology 6/63 EOBD2 User Manual
Se appare il seguente messaggio, cliccare su
CONTINUA:
If you see the following message click
CONTINUOS:
Il software è installato sul computer.
Cliccare Finish.
The software is install in your computer.
Click Finish.
ATTENZIONE:
Durante l’utilizzo del software EOBD2 chiudere tutti
i programmi che utilizzano trasmissione dati in
streaming e in Voip come SKYPE, MSN Messanger,
ecc; e chiudere inoltre tutti i browser con pagine
operanti su social network come Facebook, Twitter, ecc.
ATTENTION:
While using the software EOBD2, close all programs
that use data streaming and Voip as SKYPE, MSN
Messanger, etc; and close all browser with pages
that working on social network like Facebook,
Twitter, etc.
↑
FG Technology 7/63 EOBD2 User Manual
Windows XP: Installazione Driver - Driver installation
Di seguito mostriamo la procedura di installazione
dei driver da eseguire solo nel caso in cui il vostro
computer non riconosca l’interfaccia quando si
connette il tool alla porta usb.
Seguire le istruzioni:
We show of succession the procedure for installing
the driver to execute only if your computer doesn't
recognize the peripheral when you connect the tool
to the usb door.
Follow the istructions:
FG Technology 8/63 EOBD2 User Manual
FG Technology 9/63 EOBD2 User Manual
FG Technology 10/63 EOBD2 User Manual
FG Technology 11/63 EOBD2 User Manual
FG Technology 12/63 EOBD2 User Manual
Se il processore del computer è a 64bit
scegliere amd64:
If the processor of the computer is 64bit
choose amd64:
FG Technology 13/63 EOBD2 User Manual
FG Technology 14/63 EOBD2 User Manual
↑
FG Technology 15/63 EOBD2 User Manual
Windows 7-8-8.1-10: Installazione driver - Driver installation
È possibile che dopo aver installato il Setup.exe in
Windows 7/8, collegando lo strumento tramite il
cavo USB non venga riconosciuto poiché i driver non
sono stati installati.
Nella Gestione dispositivi della Gestione computer,
lo strumento verrà visualizzato con un triangolo
giallo come in figura successiva. Cliccare col tasto
destro del mouse sulla periferica e poi Proprietà.
After installing the Setup.exe, with Windows 7/8 is
possible that connecting it via USB cable may not be
recognized because the drivers were not installed.
In the Computer Management the tool appears with a
yellow triangle as in the figure below.
Click with the right mouse button on the device and
select Properties.
FG Technology 16/63 EOBD2 User Manual
Aprire la scheda Driver e fare Click su
“Aggiorna driver…”
Open the driver tab and Click on “Update driver..”
Selezionare
“Cerca il software del driver nel computer”
Select
“Search the software of the driver on the computer”
FG Technology 17/63 EOBD2 User Manual
Scegliere il percorso di ricerca del driver:
C:\ Fgtech\fgtech_new_driver
e spuntare “Includi sottocartelle”
Choose the path of the driver search:
C:\ Fgtech\fgtech_new_driver
and check “Include subfolders”
A questo punto il driver verrà installato: Now the driver will be installed:
Z
Se esce questo messaggio cliccare OK:
If appair this message click OK:
IL DRIVER SARA’ ORA INSTALLATO.
THE DRIVER WILL BE INSTALLED.
↑
FG Technology 18/63 EOBD2 User Manual
Attenzione:
Se apparirà il seguente messaggio:
Attention:
If appair this message:
In questo caso, occorre scegliere manualmente il
driver nel computer:
Quindi, ritornare sulla Gestione del computer >
Gestione dispositivi, tasto destro sulla periferica
FGTech e cliccare Proprietà.
Aprire la scheda “Driver”, cliccare “Aggiorna driver”
e fare Click su “Scegli manualmente da un elenco di
driver di dispositivo nel computer”:
In this case, you must manually select the drivers on
your computer:
Then, return to the Computer Management > Device
Manager, right click on the device FGTech and click
Properties.
Open the “Driver” tab, click “Update driver” and
then Click on “Let me pick from a list of device
drivers on my computer”:
Spuntare “Mostra hardware compatibile”, Check “Show compatible hardware”,
FG Technology 19/63 EOBD2 User Manual
selezionare “USB FGTech Driver” e cliccare avanti: select “USB FGTech Driver” and click next:
A questo punto il driver verrà installato: Now the driver will be installed:
Se esce questo messaggio cliccare OK:
If appair this message click OK:
IL DRIVER SARA’ ORA INSTALLATO.
THE DRIVER WILL BE INSTALLED.
Se il sistema non accetta i driver non certificati seguire le istruzioni alle pagine successive..
If the system don’t accept the drivers not signed follow the next instructions..
↑
FG Technology 20/63 EOBD2 User Manual
Windows 8: Abilitazione driver non certificato - Enable driver not signed
È possibile che dopo aver installato il Setup.exe in
Windows 8, collegando lo strumento tramite il cavo
USB non venga riconosciuto poiché i driver non sono
stati installati. Provando a forzare manualmente
l’installazione tramite la gestione delle periferiche
apparirà il seguente messaggio di errore.
After installation of the Setup.exe in Windows 8,
when you connect by USB the interface is possible
that the pc don’t recognized since the drivers are not
installed. If you try to install manually the driver
through the peripheral management it will appair the
follow error message:
È possibile risolvere il problema seguendo la stessa
procedura di Windows 7. Clicca qui per vedere.
Se non dovesse accettare i driver nemmeno
manualmente, è necessario disabilitare il
controllo della firma dei driver.
Seguire le seguenti istruzioni:
It i s possible resolve the problem following the same
procedure of Windows 7. Click here to see.
Even if it does not accept the drivers manually,
you need to disable the control of the driver signing.
Follow the followin instructions:
FG Technology 21/63 EOBD2 User Manual
Riavviare il pc in modalità avanzata, quindi dal
desktop, aprire la Charm bar di destra e cliccare
Modifica Impostazioni PC:
Restart the pc in advanced mode, so, from the
desktop, open the Charm Bar to the right and click
on Change PC Settings:
A questo punto si apre la schermata delle
impostazioni del PC, cliccare sulla sinistra la
scheda Generale:
Now it open the screened of the PC settings, click on
General and then Restart now:
Cliccare sulla destra Riavvia ora Click on the right Restart now .
Il pc si riavvierà in modalità avanzata. The PC will restart in advanced mode.
Dopo aver effettuato questo riavvio avanzato, After the restart with Windows 10, it will appair the
con Windows 8, si aprirà la seguente schermata, following screened, click on Troubleshoot
cliccare Risoluzione dei problemi:
FG Technology 22/63 EOBD2 User Manual
Cliccare su Opzioni avanzate Click on Advanced options
Cliccare su Impostazioni di Avvio Click Startup Settings
FG Technology 23/63 EOBD2 User Manual
Cliccare su Riavvia Click Restart
Dopo il riavvio, alla seguente schermata
premere il tasto 7 corrispondente a:
Disattiva impostazioni firma driver.
After the restart, at the screened below, press the
button 7 that corresponds to:
Disable driver signature enforcement.
Il pc si riavvierà.
ORA SARA’ POSSIBILE
INSTALLARE I DRIVER:
CLICCA QUI.
The PC will restart.
NOW YOU CAN INSTALL
THE DRIVER:
CLICK HERE .
↑
FG Technology 24/63 EOBD2 User Manual
Windows 8.1: Abilitazione driver non certificato - Enable driver not signed
È possibile che dopo aver installato il Setup.exe in
Windows 8.1, collegando lo strumento tramite il
cavo USB non venga riconosciuto poiché i driver non
sono stati installati. Provando a forzare manualmente
l’installazione tramite la gestione delle periferiche
apparirà il seguente messaggio di errore.
After installation of the Setup.exe in Windows 8.1,
when you connect by USB the interface is possible
that the pc don’t recognized since the drivers are not
installed. If you try to install manually the driver
through the peripheral management it will appair the
follow error message:
È possibile risolvere il problema seguendo la stessa
procedura di Windows 7. Clicca qui per vedere.
Se non dovesse accettare i driver nemmeno
manualmente, è necessario disabilitare il
controllo della firma dei driver.
Seguire le seguenti istruzioni:
It i s possible resolve the problem following the same
procedure of Windows 7. Click here to see.
Even if it does not accept the drivers manually,
you need to disable the control of the driver signing.
Follow the followin instructions:
Aprire la Charm bar di destra e cliccare Open the Charm bar to the right and click
FG Technology 25/63 EOBD2 User Manual
MODIFICA IMPOSTAZIONI PC: CHANGE PC SETTINGS:
Cliccare Aggiorna e ripristina: Click Update and restore:
Cliccare Ripristino
e poi a destra Riavvia ora:
Click Restore
and then Restart now to the right:
FG Technology 26/63 EOBD2 User Manual
Il PC si riavvierà in modalità avanzata. The PC will restart in advanced mode.
Dopo aver effettuato questo riavvio avanzato, After the restart with Windows 10, it will appair the
con Windows 8, si aprirà la seguente schermata, following screened, click on Troubleshoot
cliccare Risoluzione dei problemi:
FG Technology 27/63 EOBD2 User Manual
Cliccare su Opzioni avanzate Click on Advanced options
Cliccare su Impostazioni di Avvio Click Startup Settings
Cliccare su Riavvia Click Restart
FG Technology 28/63 EOBD2 User Manual
Dopo il riavvio, alla seguente schermata
premere il tasto 7 corrispondente a:
Disattiva impostazioni firma driver.
After the restart, at the screened below, press the
button 7 that corresponds to:
Disable driver signature enforcement.
Il pc si riavvierà.
ORA SARA’ POSSIBILE
INSTALLARE I DRIVER:
CLICCA QUI.
The PC will restart.
NOW YOU CAN INSTALL
THE DRIVER:
CLICK HERE .
↑
FG Technology 29/63 EOBD2 User Manual
Windows 10: Abilitazione driver non certificato - Enable driver not signed
È possibile che dopo aver installato il Setup.exe in
Windows 10, collegando lo strumento tramite il cavo
USB non venga riconosciuto poiché i driver non sono
stati installati. Provando a forzare manualmente
l’installazione tramite la gestione delle periferiche
apparirà il seguente messaggio di errore.
After installation of the Setup.exe in Windows 10,
when you connect by USB the interface is possible
that the pc don’t recognized since the drivers are not
installed. If you try to install manually the driver
through the peripheral management it will appair the
follow error message:
È possibile risolvere il problema seguendo la stessa
procedura di Windows 7. Clicca qui per vedere.
Se non dovesse accettare i driver nemmeno
manualmente, è necessario disabilitare il
controllo della firma dei driver.
Seguire le seguenti istruzioni:
It i s possible resolve the problem following the same
procedure of Windows 7. Click here to see.
Even if it does not accept the drivers manually,
you need to disable the control of the driver signing.
Follow the followin instructions:
FG Technology 30/63 EOBD2 User Manual
Riavviare il pc in modalità avanzata, quindi dal
desktop, quindi cliccare Start > Impostazioni
Restart the pc in advanced mode, so click
Start > Settings
Cliccare Aggiornamento e sicurezza: Click Update and security:
FG Technology 31/63 EOBD2 User Manual
Cliccare Ripristino
e poi a destra Riavvia ora:
Click Restore
and then Restart now to the right:
Il PC si riavvierà in modalità avanzata. The PC will restart in advanced mode.
Dopo aver effettuato questo riavvio avanzato,
Windows 10 si aprirà la seguente schermata, cliccare
Risoluzione dei problemi:
After the restart with Windows 10, it will appair the
following screened, click on Troubleshoot:
FG Technology 32/63 EOBD2 User Manual
Cliccare su Opzioni avanzate Click on Advanced options
Cliccare su Vedi altre opzioni di ripristino Click See other restore settings
Cliccare su Impostazioni di Avvio Click Startup Settings
FG Technology 33/63 EOBD2 User Manual
Cliccare su Riavvia Click Restart
Dopo il riavvio, alla seguente schermata
premere il tasto 7 corrispondente a:
Disattiva impostazioni firma driver.
After the restart, at the screened below, press the
button 7 that corresponds to:
Disable driver signature enforcement.
Il pc si riavvierà.
ORA SARA’ POSSIBILE
INSTALLARE I DRIVER:
CLICCA QUI.
ATTENZIONE:
ALL’AVVIO DEL SOFTWARE
EOBD2.EXE SE ESCE UN AVVISO
DI “APP NON SICURA”
CLICCARE “INFORMAZIONI
AGGIUNTIVE” E POI “CONSENTI”.
The PC will restart.
NOW YOU CAN INSTALL
THE DRIVER:
CLICK HERE .
ATTENTION:
WHEN YOU START EOBD2.EXE IF
APPAIR A MESSAGE “APP NOT SICURE”
CLICK “MORE INFORMATION” AND
THEN “ALLOW”.
↑
FG Technology 34/63 EOBD2 User Manual
Compatibilità Windows XP in Windows Vista / 7 / 8 / 8.1
Se si sta utilizzando il sistema operativo Windows
Vista o 7 o 8 è necessario impostare la compatibilità
Windows XP al software EOBD2 e, se presente,
anche al software WINMAP.
Aprire la cartella dove è installato il software
EOBD2:
If you use Windows Vista or 7 or 8 operating system
it need to set the Windows XP compatibility mode in
the property to the software EOBD2 and, if you
have, to WINMAP.
Open the folder where is installed the software
EOBD2:
FG Technology 35/63 EOBD2 User Manual
Tasto destro sul file EOBD2.exe: Right click on the file EOBD2.exe
Cliccare Proprietà: Click Property:
FG Technology 36/63 EOBD2 User Manual
Si aprirà la seguente finestra: It will open the following window:
Cliccare Compatibilità: Click Compatibility:
FG Technology 37/63 EOBD2 User Manual
Selezionare:
Esegui il programma in modalità compatibilità
per: Windows XP (Service Pack 3)
Select:
Execute the program in compatibility mode for
Windows XP (Service Pack 3)
Cliccare: Applica Click Apply:
ATTENZIONE:
Se presente, applicare le stesse proprietà al
software WINMAP.exe
ATTENTION:
If tou have, apply the same property to software
WINMAP.exe
FG Technology 38/63 EOBD2 User Manual
Impostazioni account – Account settings
Di seguito mostriamo come settare l’impostazione
dell’account in Windows per migliorare il
funzionamento il sistema operativo per il migliore
utilizzo del programma EOBD2:
Nel Pannello di controllo cliccare
“Account utente e protezione famiglia”:
Below show how to set up the account setup in
Windows to improve the funcioning of the operating
system for the best use of the EOBD2 software:
In the Control Panel click
“User accounts and family safety”:
FG Technology 39/63 EOBD2 User Manual
Account utente: User account:
Cliccare su:
Modifica le impostazioni di Controllo
dell’account utente
Click on:
Modifies the formulations of Control of the consumer
account
FG Technology 40/63 EOBD2 User Manual
Selezionare :
Non notificare mai
Select:
Do not notify never
FG Technology 41/63 EOBD2 User Manual
Impostazione Windows Firewall - Windows Firewall settings
Di seguito mostriamo come settare il Firewall di
Windows per migliorare la comunicazione tra
EOBD2/Updater e il Server FG Technology.
Nel Pannello di controllo cliccare
Sistema e Sicurezza
Below we show how to set the Windows Firewall to
improve communication between EOBD2 / Updater
and Server FG Technology .
In Control Panel, click
System and Security
Cliccare Windows Firewall
Click Windows Firewall
FG Technology 42/63 EOBD2 User Manual
Cliccare: Consenti programma o funzionalità con
Windows Firewall
Click: Allow a program or feature through Windows
Firewall
Cliccare: Consenti un altro programma… Click: Allow another program...
FG Technology 43/63 EOBD2 User Manual
Cliccare: Sfoglia… Click: Browse…
Selezionare EOBD2.exe Select EOBD2.exe
FG Technology 44/63 EOBD2 User Manual
Cliccare: Aggiungi Click: Add
Cliccare: OK Click: OK
ATTENZIONE:
Ripetere l’operazione con FGTech_UPDATER.exe
ATTENTION:
Repeat the procedure with FGTech_UPDATER.exe
FG Technology 45/63 EOBD2 User Manual
FGTech_UPDATER
Per eseguire gli aggiornamenti software, i rinnovi
di licenza e visualizzare la data di scadenza
abbonamento, utilizzare FGTech_UPDATER.exe
che si trova in:
C:\ FGTech\DOWNLOAD_UPDATE
Oppure è possibile scaricarlo dal sito
www.fgtechnology.eu nell’area Download.
Attenzione: In questo caso, occorre salvarlo
sempre nella cartella:
C:\ FGTech\DOWNLOAD_UPDATE
For software update, licence renewal and see the
date of expiration subscription you can use
FGTech_UPDATER.exe
that you can find in:
C:\ FGTech\DOWNLOAD_UPDATE
Or it is possible to download it from the web site
www.fgtechnology.eu in the Download area.
Attention: In this case, you have to save
always in the folder:
C:\ FGTech\DOWNLOAD_UPDATE
Di seguito sono elencate le funzionalità
dell’FGTech_UPDATER:
Of succession have listed the functions of the
FGTech_UPDATER:
FG Technology 46/63 EOBD2 User Manual
Download . . . . . . . . . Permette di scaricare dal server il
software di Download Update sempre
aggiornato.
Allows you to download from the server the
software of Download Update.
Tool number . . . . . . Indica il numero dell’interfaccia.
It show the number of the tool.
Request licence . . . .. Alla scadenza dell’anno di abbonamento;
utilizzare questo pulsante per richiedere
una nuova licenza per un altro anno di
utilizzo. Cliccando questo pulsante,
viene creato nella stessa directory un file
con estensione .bin. Questo file dovrà
essere inviato via e-mail al nostro
supporto tecnico per richiedere il rinnovo
di licenza.
Vedi paragrafo “Gestione licenze”.
At the expiration of the year of subscription;
use this button for require a new licence. If
you click this button, it created in the same
directory a file with extension .bin.
You have to send this file by e-mail to our
technical support for require a renovation
of licence.
See paragraph “Licence management”.
Load Licence. . . . . . Utilizzare questo tasto per caricare il file
con estensione .bin della nuova licenza
che avrete ricevuto in risposta via e-mail
dal nostro supporto tecnico.
Al caricamento effettuato, il software
verrà sbloccato e attivato per un altro
anno di utilizzo.
Vedi paragrafo “Gestione licenze”.
Use this button for loading a file with
extension .bin of the new licence that you
will recived from our technical support.
When the loading is done, the software will
be abilitate and activated for another year.
See paragraph “Licence management”.
Help. . . . . . . . . . . . . . Apre il manuale utente
Open the user manual
Exit. . . . . . . . . . . . . . . Chiude la finestra
Close the window
FG Technology 47/63 EOBD2 User Manual
Dopo aver cliccato DOWNLOAD
Verificare che la data del computer sia corretta e
cliccare OK:
When you click DOWNLOAD
take care about correct computer date and
click OK:
Assicurarsi che la connessione a internet sia attiva e
cliccare OK:
Check that your connection to internet is active and
click OK:
L’Updater si connetterà al server e scaricherà
l’ultima versione di Download Update presente:
The Updater will connect to the server and it will
download the last version of Download Updete:
FG Technology 48/63 EOBD2 User Manual
Cliccare START alla seguente finestra per avviare
l’aggiornamento:
In the following window click START for starting the
update:
Si potrà vedere la data di scadenza dell’abbonamento
e la barra di avanzamento con la percentuale di
scaricamento:
You will seen the date of subscription expiry and the
bar of advancement with the percentage of
download:
Al termine, apparirà il seguente messaggio
di download completato. Click su OK
At the end, the following message of completed
download will appear. Click OK
↑
FG Technology 49/63 EOBD2 User Manual
Gestione licenze - Licence management
Richiesta Licenza
(Guard il video su Youtube per creare la licenza:
https://www.youtube.com/watch?v=BkmNyNhmtio)
---
Alla scadenza dell’anno di abbonamento, utilizzare
questo pulsante per richiedere una nuova licenza per
un altro anno di utilizzo.
Request licence
(Watch video on Youtube for create a licence:
https://www.youtube.com/watch?v=BkmNyNhmtio)
---
At the expiration of the year of subscription, use this
button for require a new licence.
Cliccando questo pulsante, viene creato nella
stessa directory un file con estensione .bin.
Cliccare OK
If you click this button, it created in the same
directory a file with extension .bin.
Click OK
Segue a pagina successiva Follow on next page
FG Technology 50/63 EOBD2 User Manual
Questo file chiamato
Request_Licence_xxxxxxxx.bin
dovrà essere inviato all’indirizzo e-mail
[email protected] del nostro supporto
tecnico per richiedere la nuova licenza.
This file called
Request_Licence_xxxxxxxx.bin
It will be send to the e-mail address
[email protected] of our technical support for
request the new licence.
A pagina successiva come caricare la licenza..
On next page how load the licence..
FG Technology 51/63 EOBD2 User Manual
Caricamento Licenza
(Guard il video su Youtube per caricare la licenza:
https://www.youtube.com/watch?v=xecDbbZzqq4)
---
Dopo aver ricevuto dal nostro supporto tecnico il
file per l’attivazione della nuova licenza, è
necessario caricarlo a sistema cliccando il tasto
LOAD LICENCE.
Attenzione:
La connessione ad internet deve essere attiva.
Load Licence
(Watch video on Youtube for load the licence:
https://www.youtube.com/watch?v=xecDbbZzqq4)
---
After received the file for the activation of the new
licence from our technical support, you need to
upload to the system click the button
LOAD LICENCE:
Attention:
The internet connection must be active.
Si aprirà una finestra di caricamento file;
selezionare il file ricevuto chiamato
Licence_FGTecxxxxx.bin:
It will open a window for loading the file,
select the received file called
Licence_FGTecxxxxx.bin:
La nuova licenza è ora attivata: The new licence is now actived:
↑
FG Technology 52/63 EOBD2 User Manual
LOG File
All’interno della cartella FGTech in cui è
installato il programma, è presente una cartella
che contiene i file di LOG chiamata
EOBD2_LOG:
In questa cartella il programma salva tutti i file di
errore relativi a problemi avvenuti in fase di
comunicazione con le centraline.
Quindi, in caso di un errore di questo tipo,
inviare i file di LOG (con estensione .gal) che
trovate all’interno di questa cartella all’indirizzo
e-mail [email protected] relativi al
problema della centralina con cui state
comunicando.
Il supporto tecnico risponderà appena possibile
per risolvere il problema.
To the inside of the FGTech briefcase in which is
installed the program, there is a folder that contain
the LOG files called EOBD2_LOG:
In this folder the program save all the error file
about problems happenes in case of comunication
with the ECUs.
So, In case of error, send the LOG files (with
extension .gal) that you can find in this folder at the
e-mail addres [email protected] relative to
the Ecu with which you are communicating.
The technical support will answer as soon as
possible for resolve the problem.
FG Technology 53/63 EOBD2 User Manual
L’altra cartella dei file di log è chiamata:
FTP_LOG e viene creata nella stessa directory
in cui è presente il programma
FGTech_DOWNLOAD_UPDATE.exe
In questa cartella il programma salva tutti i file di
errore relativi a problemi di connessione al
nostro server del programma di aggiornamento
FGTech_download_update.
Quindi, in caso di un errore di questo tipo,
inviare il file di LOG (con estensione .gal) che
trovate all’interno di questa cartella all’indirizzo
e-mail [email protected].
Il supporto tecnico vi risponderà appena
possibile per risolvere il problema.
The other folder of log file is called
FTP_LOG and it is created in the same directory in
which there is the program
FGTech_DOWNLOAD_UPDATE.exe
In this folder the program save all the error file
about problems of connection to our server of the
program FGTech_download_update.
So, In case of error, send a LOG file
(with extension .gal) that you can find in this folder
at the e-mail addres [email protected].
The technical support will answer as soon as
possible for resolve the problem.
↑
FG Technology 54/63 EOBD2 User Manual
Crypt-decrypt SLAVE
Cliccando il tasto “Master” sulla finestra
principale dell’EOBD2 puoi aprire la sezione di
criptaggio e decriptaggio file dello Slave:
Clicking the “Master” button on your main EOBD2
window you can open the section of crypt and
decrypt of the Slave files:
FG Technology 55/63 EOBD2 User Manual
Caricare il file criptato mandato dallo Slave nella
prima riga, poi scrivere il nome del file
decriptato nella seconda riga a cliccare il
pulsante “Decrypt & Save”.
Ora il file decriptato è salvato con nome come in
seconda riga.
You have to load the crypted file of your slave in the
first row, then write the name of the uncrypted file in
the second row and click on “Decrypt & Save”
button.
Now you have saved the uncrypted file whit name
like second row.
FG Technology 56/63 EOBD2 User Manual
Modificare il file e ricriptarlo prima di spedirlo
allo Slave.
Per ricriptarlo caricare il file ricevuto nella prima
riga della sezione Crypt, poi caricare il file
modificato (non criptato) nella seconda riga e
scrivere nella 3° riga il nome del file finale da
spedire.
Ora cliccare il tasto “Crypt & Save” e si crea il
file modificato e criptato per lo slave, Exit.
You can tuning the file and you have to crypt it again
before sending to your Slave.
For crypting you must load the crypted file recived in
the first row of Crypt section, then load the
(uncrypted) tuned file in the second row and write
name in the 3° row of the final crypted file to send.
Now you can click on button “Crypt & Save” end
Exit.
ATTENZIONE:
Se dovete inviare file allo Slave di centraline che
non si possono leggere e quindi non avete il file
proveniente dallo slave ma da un vostro archivio
master, è possibile caricare su “Costumer File
Crypted” un qualsiasi altro file dello stesso slave
e procedere normalmente per gli altri campi
“Source File mod.” e “Destination File Crypted
Mod.”
ATTENTION:
If you have to send a file to the slave of Ecu that they
could not be read and so you therefore don't have the
deriving file from the Slave but from a your Master
file, is possible load in the “Costumer File Crypted”
an any other file of the same Slave and proceed
normally for the other fields “Source File mod.”
and “Destination File Crypted Mod”.
↑
FG Technology 57/63 EOBD2 User Manual
KIT EOBD2
EOBD2 TOOL
OBD CABLE
TRICORE CABLE
Segue a pagina successiva… / Follow to next page…
FG Technology 58/63 EOBD2 User Manual
RENESAS CABLE
STANDARD ADAPTER
VOLVO/RENAULT TRUCK ADAPTER
BDM ADAPTER BOSCH
BDM ADAPTER DELPHI
BDM ADAPTER SIEMENS/MARELLI Ver.1
BDM ADAPTER SIEMENS/MARELLI Ver.2
PRESS ADAPTER
Segue a pagina successiva… / Follow to next page…
FG Technology 59/63 EOBD2 User Manual
POWER CABLE FOR BDM BOSCH
FLAT CABLE
COLORED FLAT CABLE
SHORT COLORED FLAT CABLE
.
PIN STRIP FOR BDM
FG Technology 60/63 EOBD2 User Manual
Alimentazione - Power supply
Per alimentare l’interfaccia utilizzare un
alimentatore +12/24V da inserire nella presa
jack del tool. Il led rosso si illuminerà.
To give power to the tool use a power supply
+12/24V and insert it to the jack plug of the
tool. The red led will light.
In alternativa è possibile alimentare lo strumento
utilizzando una batteria 12/24V da collegare alla
spina bianca del cavo Tricore/Renesas.
Alternatively, it is possible to give power to the tool
using a battery 12/24V, connect it to the white plug
of Tricore/Renesas cable.
↑
FG Technology 61/63 EOBD2 User Manual
FOR HARDWARE SINCE 2012:
Adattatori / Adapter Standard - Adattatori / Adapter Volvo / Renault Truck
In dotazione sono presenti due adattatori:
- Adattatore Standard
- Adattatore Volvo/Renault Truck
Prima di iniziare a comunicare con una vettura
tramite presa OBD, collegare l’adattatore Standard
alla presa DB15 dell’interfaccia com in figura:
In endowment there are two adapter:
- Standard Adapter
- Volvo/Renault Truck Adapter
Before to communicate with an ECU of a
vehicle through the OBD, connect the Standard
Adapter to the DB15 of the tool like in figure:
ATTENZIONE:
Se si sta lavorando con JTAG o con processori
Renesas non bisogna utilizzare l’adattatore
STANDARD.
ATTENTION: If you are working with JTAG or with
Renesas processors don’t use STANDARD
adapter.
Nel caso di comunicazione con centraline Volvo
Truck o centraline Renault Truck, togliere
l’adattatore standard dal lato DB15 del tool, ed
inserire l’Adattatore Volvo/Renault Truck tra la
spina del cavo OBD e la presa OBD del camion:
If you have to communicate with ECUs of
Volvo Truck or ECUs of Renault Truck, use
the Volvo/Renault Truck Adapter from the
OBD taking of OBD of the truck side of OBD
cable:
FG Technology 62/63 EOBD2 User Manual
SE NON VENGONO UTILIZZATI QUESTI
ADATTATORI QUANDO NECESSARIO SI
RISCHIA DI DANNEGGIARE
IRREPARABILMENTE L’INTERFACCIA
EOBD2 E IL PROPRIO COMPUTER.
LA RESPONSABILITA’ DI EVENTUALI
DANNI IN CASO DI COLLEGAMENTO
SENZA ADATTATORI APPARTIENE
SOLO ALL’UTILIZZATORE DEL TOOL.
IF YOU DON’T USE THESE
ADAPTORS WHEN NECESSARY YOU
RISK TO DAMAGE IRREPARABLY
THE EOBD2 TOOL AND YOUR
COMPUTER.
THE RESPONSIBILITY OF POSSIBILE
DAMAGE IN CASE OF CONNECTIONS
WITHOUT ADAPTERS BELONG ONLY
AT THE USER OF THE TOOL.
↑
FG Technology 63/63 EOBD2 User Manual
EOBD2 USER MANUAL
EOBD 2 USER MANUAL
Versione Gennaio 2017
Version January 2017
↑