© 2016 Cascade Yarns® - All Rights Reserved.

Bentley Highlands Pullover

W638

Designed by

Shannon Thomas

© 2016 Cascade Yarns® - All Rights Reserved.

Bentley Highlands Pullover

Designed by Shannon Thomas

This top-down raglan sweater is the perfect answer to easy, grab-n-go situations for your little one.

Skill Level: Beginner Finished Chest Measurements: 19” (20”, 21”, 22”) Materials: Cascade Yarns® Bentley 75% Acrylic / 25% Superwash Wool 100 g (3.5 oz) / 207.8 yds (200 m) 2 skeins of color #03 (Cherry) US 7 circular knitting needles US 5 circular knitting needles Stitch holders Stitch Markers Yarn needle Gauge: 20 sts x 28 rows = 4” (10 cm)

Abbreviations: BO = Bind Off CO = Cast On K = Knit K2tog = Knit 2 stitches together KFB = Knit front and back of a stitch M1L = Make 1 stitch left M1R = Make 1 stitch right P = Purl PFB = Purl front and back of a stitch PM = Place Marker Rnd(s) = Round(s) RS = Right Side SM = Slip Marker SSK = Slip, Slip, Knit St(s) = Stitch(es) WS = Wrong Side

Yoke: Using stretchy CO (Designer used TillyBuddy’s Stretchy Cast On Method), CO 46 (48, 50, 52). Set-up Row (WS): PFB, PM, P6 (6, 6, 7), PM, P16 (17, 18, 18), PM, P6 (6, 6, 7), PM, P16 (17, 18, 18), PM, PFB. Row 1: KFB, *[K to 1 st before marker, KFB, SM, KFB]; repeat from * 3 times to last st, KFB. Row 2: Purl, slipping markers as you reach them. Repeat these two rows 2 (2, 2, 2) times. Knit row 1 once.

© 2016 Cascade Yarns® - All Rights Reserved.

Row 1: *[K to 1 st before marker, KFB, SM, KFB]; repeat from * 3 times to end. Row 2: Knit Continue increasing until your raglan line measures 3” (3, 3½, 3¾)” Remove your marker at center neckline. Knit to next marker (front of left sleeve). Remove marker. Slip sleeve sts to stitch holder. Using backward loop method, CO 4 (4, 6, 6) sts. Remove marker (left back sleeve) and knit across back to next marker. Remove marker (right sleeve back) and slip sleeve sts to stitch holder. Reposition Markers Rnd: Using backward loop method, CO 2 (2, 3, 3) sts. PM indicating beginning of rnd. Using backward loop method, CO 2 (2, 3, 3) sts. Remove next marker which had been indicating front of right sleeve. Knit in the rnd until piece measures 7½” (8, 8½, 8¾)” from back neck. Ribbing: Switch to smaller needles. *[K1, P1]; repeat from * to end of rnd. Work ribbing for 1” or desired length. BO loosely using larger needle. Cut yarn, leaving strand long enough to weave in later. Sleeves With larger needle, beginning at base of armhole, pick up 4 (4, 6, 6) sts at the underarm and work all sts from the stitch holder. Join, placing a marker evenly dividing the CO sts that you just picked up, indicating beginning of rnd. Rnd 1: SM, K1, K2tog, work to last 3 sts, SSK, K1. Rnd 2-10: Knit Repeat rnd 1. Work without further decreases until sleeve measures 10” (11, 11, 12)” from underarm to wrist. Sleeve Ribbing: Switch to smaller needles. *[K1, P1]; for 1½” or desired length. BO loosely with larger needle, leaving tail of yarn long enough to weave in later. Repeat process for second sleeve. Finishing: Block. Weave in ends.