Ensentic - Texas Electronics Home Page...ESB-100 020-001 Barometric pressure sensor O Y O Y ESR-300...

Ensentic EWC-100 Controller

User’s Manual Rev: 180728

ENSENTIC MCKINNEY, TX WWW.ENSENTIC.COM

Ensentic E N VI R ON M EN TA L S EN SO R D AT A A NY T I M E , AN Y WH E R E

a) Notices © Copyright 2018 Ensentic

All Rights Reserved

This publication is protected by copyright and all rights are reserved. Any reproduction of this

manual is prohibited without express written permission from Ensentic. Ensentic assumes no responsibility

for any inaccuracies that may be contained in this manual and any information is subject to be changed.

CE

Our sensors meet CE standards and complying with EN 61326-1 Industrial Immunity and EN55011 Class A

Emissions.

RoHS

All electronic and mechanical components conform to RoHS, Directive 2002/95/EC.

b) Device Info

• Basic Info

• Supported Sensors

• Sensor Connectors

• Device Image For the Connection References

1) Basic Info - This is a device with which anyone can take/check weather conditions from anywhere and then

report to anywhere.

- By using this device user can monitor the weather aspects like Temperature, Humidity, Wind-

speed, Wind-direction, Barometric Pressure, Rain-Fall, Solar energy, Soil-Moisture level etc with

very high accuracy

- This is a battery operated (plus direct adapter option is available) device and with recommended

solar panel this device can long last up to 8 days even there is no sun or bad weather.

- The Ensentic EWC-100 controller or data logger works as the “brains” of system. It is based on

the STM32 ARM Cortex M3 microcontroller. The microcontroller is responsible for all

communications, data collecting and storage, communications, user interface, measurement

conversions. The tight integration of all these functions allows for high optimization of the

whole system while maintaining a high level of measurement accuracy and operational

simplicity.



2) Supported Sensors - ESW-200 Wind Speed and Direction

ESW-200 provides both the wind speed and direction signals. Constructed of anodized machined

aluminium it utilizes stainless bearings.

- EST-200 Temperature and humidity sensor

ESW-200 provides both the wind speed and direction signals. Constructed

- ESP-100 Solar sensor

ESW-200 provides solar radiation intensity. Constructed of anodized machined aluminium

- ESR-300 Rain gauge

ESW-200 provides both the rain intensity and amount on signals. Constructed of anodized

machined aluminium

- ESB-100 Barometric pressure sensor

ESW-200 provides barometric pressure signals. Mounted directly on the PCB inside cabinet.

- ESS-200 Soil moisture sensor

ESW-200 provides both the soil moisture and temperature signals.

- ESL-300 Lightning detection sensor

ESW-200 provides remote lightning signals.

- ESP-110 U.V. Solar sensor

ESW-200 provides U.V. intensity signals. Constructed of anodized machined aluminium

- ESP-120 PAR Solar sensor

ESW-200 provides intensity of PAR solar signals. Constructed of anodized machined aluminium

Sensor and Peripheral Descriptions

Integrated Cell Phone

The integrated cell phone module. The module transmits data to your Data center for system that cannot access

Wi-Fi signals. A cell phone service account is required.



3) Options

Model SKU Description CWS-100

CWS-150

CWS-200

CWS-250

EWS-100 250-100 weather station kit 12VDC

EWS-150 250-150 weather station loaded kit 12VDC

EWS-200 250-200 weather station kit solar pwr

EWS-250 250-250 weather station loaded kit solar pwr

EWC-100 120-001 EWC-100 CONTROLLER Y Y Y Y

EST-200 040-001 temperature/humidity sensor Y Y Y Y

ESW-200 030-001 Wind speed&direction sensor Y Y Y Y

ESP-100 060-001 Solar sensor O Y O Y

ESB-100 020-001 Barometric pressure sensor O Y O Y

ESR-300 080-001 Rain gauge O Y O Y

ESS-200 050-001 Soil moisture sensor O O O O

ESL-300 070-001 Lightning sensor O O O O

ESP-110 060-001 U.V. Solar sensor O O O O

ESP-120 060-002 PAR Solar sensor O O O O

ESA-001 010-001 Sim Card O O O O

ESA-050 105-002 20W SOLAR PANEL KIT O O Y Y

ESH-100 110-001 10 ft mast O Y O Y

ESH-110 110-003 CROSS-ARM KIT O Y O Y

ESH-115 105-001 SOLAR SENSOR CROSS-ARM MOUNT O Y O Y

ESH-300 110-002 Lightweight aluminum tripod O O O O



CONNECTING TO THE NETWORK: A. If you have a WIFI connected device follow sets 1 -4

B. if you have a cellular connected device and you are in range of a cell tower then you are already

connected to the internet, so you can skip

NOTE: This will be performed only one time unless you want to connect to a different router or

change the name or password of the router.

1. Open the controller door and Connect the battery connector so the controller has

power, OR if not supplied with battery then supply 12V DC power to the power supply

PCB behind main PCB.

Battery

connector

12VDC

supply



2. Press and hold the left button until you see a blinking dark blue light

3. Then go to nearby PC with wireless access and at lower right-hand corner of a screen

you will see internet access and click the connect button next to the “Photon” that will

appear, this may take a few seconds to appear. If using a smartphone to do this, go to

the phone’s Wi-Fi settings and do the same.

Photon



4. On the PC or smartphone, go to a browser and type in this address 192.168.0.1 (take a

minute or two for it to access this. Be patient)

and it should bring up this page

5. Click this Scan button to see available networks



Congratulations! You should now be connected to the network and the internet, check to see if

connected, it may show trying to connect but may be connect already. You may now need to

change you PC or smartphone Wi-Fi setting back, most will reset automatically.

Select the network you

want to connect to Type in the correct

password

Then click the

Connect button



1. Go to a browser and type www.ensentic.com then click DATA CENTER

2. Type in your email, first name, last name, password to sign up

Under first tab is Devices. Here you need to enter the

A. 9-digit station key that was included with your equipment.

B. station name (any name you like)

C. the elevation of the equipment (in ft.)

D. time interval is how often you want it to upload sensor reading to the Data Center

E. your timezone

F. check the box if you want to use day light savings time

G. click the Submit button

http://www.ensentic.com/



Then you will see a screen that looks something like this

If you need to change something, click this blue edit button

Once the controller reaches the end of the time interval it reads these settings, the Accept light

will turn green and it will then begin to use these settings

The next tab is the Dashboard and it will look something like this.

You will have three tabs within this window. Current Weather, History, Data



The next tab is the Alerts and it will look something like this.

To receive alert: click the email button then your weather station then parameter then

condition and save.

The last tab is the Units. This saves your desired units for your sensors

Your connection to the Wi-fi router should be strong to received data consistently. Make sure

you are within 100 feet and you will see you should have at least 40% signal strength shown

under your Data Tab.



c) Hardware User Guide

• Power Supply

• Sensor Wiring

1) Power Supply :- - This device can operate using the 12v DC power supply. (Minimum is 10v DC while Maximum is

18v DC)

- It has two options to provide the power supply

• 12V Solar Panel/Battery

• 12v Direct Adaptor

2) Sensor Wirings :

f) Guide to start the weather station for the beginners.

1) Wire all the sensor. (refer section b)

2) Mount the photon/electron

3) Plug the power supply.

4) Connect the photon to WIFI.

5) If you want to change default configuration and other parameters then you can do that using section E .



WARRANTY AND RETURN POLICY

Ensentic will accept returns within 30 days of purchase if the product is in new condition (to be determined by Ensentic). Returns are

subject to a 10 % restocking fee.

What is Covered

All products manufactured by Ensentic are warranted to be free from defects in materials and craftsmanship for a period of two (2)

years from the date of shipment from our factory. To be considered for warranty coverage an item must be evaluated either at our

factory or by an authorized distributor.

What is Not Covered

The customer is responsible for all costs associated with the removal, reinstallation, and shipping of all warranty items to our factory.

The warranty does not cover equipment that has been damaged due to the following conditions:

1. Improper installation or abuse.

2. Operation of the instrument outside of its specified operating range.

3. Natural occurrences such as lightning, fire, etc.

4. Unauthorized modification.

5. Improper or unauthorized repair.

6. Removal of the original serial number label or reprogramming of the electronic serial number voids any warranty on the device. Please note that accuracy drift is expected over time. Routine recalibration of sensors/meters is considered part of proper

maintenance and will not be covered under warranty.

This warranty covers the original purchaser of the product or other party who may own it during the warranty period.

What we will do

1. Either repair or replace (at our discretion) the item under warranty.

2. Ship the item back to the customer by the carrier of our choice. Different or expedited shipping methods will be at the customer’s

expense.

Ensentic - Texas Electronics Home Page...ESB-100 020-001 Barometric pressure sensor O Y O Y ESR-300...

Documents

Transcript of Ensentic - Texas Electronics Home Page...ESB-100 020-001 Barometric pressure sensor O Y O Y ESR-300...