English Warranty, Regulatory Information, and...

Warranty, RegulatoryInformation, andSpecifications

English

| OKICOLOR 82

DisclaimerEvery effort has been made to ensure that the information inthis document is complete, accurate, and up-to-date. OkiData assumes no responsibility for the results of errors oromissions beyond its control. Oki Data also cannotguarantee that changes in software and equipment made byother manufacturers and referred to in this document will notaffect the applicability of the information in it. Mention ofsoftware products manufactured by other companies does notnecessarily constitute endorsement by Oki Data.

Copyright InformationCopyright 1999 by Oki Data. All Rights ReservedFirst Edition: September, 1999

Written and produced by the Oki Data Training andPublications Department.

Contact InformationPlease address any comments on this publication to:

Mailing Address

Oki Data Americas, Inc.Training and Publications Department2000 Bishops Gate BoulevardMount Laurel, NJ 08054-4620United States of America

e-Mail Address

[email protected]

Web Site

Please visit Oki Data’s multilingual web site at:

http://www.okidata.com

Trademark InformationOKI is a registered trademark of Oki Electric IndustryCompany, Ltd.

OKICOLOR is a trademark of Oki Electric Industry Co., Ltd.

Energy Star is a registered trademark of the United StateEnvironmental Protection Agency.

Touch-Tone is a registered trademark of American Telephoneand Telegraph.

Windows is either a registered trademark or a trademark ofMicrosoft Corporation in the United States and/or othercountries

ZIP Code is a registered trademark of the United States PostalService

Emergency First Aid InformationRefer to the Material Safety Data Sheet at the end of thisdocument.

Overview

|Warranty, Regulatory Information, and Specifications: English 3

ContentsYear 2000 Compliance............................................ 4Energy Star .............................................................. 4Limited Warranty .................................................... 5

Limited Warranty—United States and Canada .............. 5Limited Warranty—Latin America ................................. 8

Oki Data Depot Service Centers ........................... 9Authorized Service Providers ......................................... 9

Important Safety Information ............................. 11Regulatory Information ....................................... 13Specifications.......................................................... 16Material Safety Data Sheets ................................ 18

| OKICOLOR 84

Year 2000Compliance

All products currently sold by Oki Data are Year 2000Compliant. Each product contains information technologythat accurately processes date and time data between theyears 1999 and 2000, and carries no issue for the September9, 1999 (9999) programming concern. These products, whenused in combination with products purchased from othermanufacturers, whose products properly exchange data andtime information, will accurately process the date and time.All future products are committed to meeting the same Year2000 compliance.

Energy Star

As an Energy Star® Partner, Oki Data has determined that thisproduct meets the Energy Star guidelines for energyefficiency.

Overview


Limited WarrantyLimited Warranty—United States andCanada

Oki Data Americas, Inc. (Oki Data) warrants this printer to befree from defect in material and workmanship and willremedy any such defect according to the terms of this LimitedWarranty. This Limited Warranty extends to the originalpurchaser only. This Limited Warranty does not extend tonetwork setup, application conflicts, or consumable itemsincluding, but not limited to, image drum cartridges, tonercartridges, fuses, etc.

Oki Data will repair (or at its option, replace) at no charge,any defective component(s) of the Printer for one (1) yearfrom the date of purchase except for the printheads (LEDimaging arrays), which are warranted for a period of five (5)years from date of purchase. This Limited Warranty extendsto the original purchaser only. This Limited Warranty doesnot extend to consumable items.

Consumables are covered separately under individualconsumable warranties. Please refer to the appropriateconsumable item’s warranty for further information.

On-Site Repair

! On-Site Repair is available in the United States andCanada only. On-Site Repair does not include thereplacement or repair of product consumables orsupplies.

Oki Data will, for a period of one (1) year from the date ofpurchase, repair (or replace at its option) on-site at theoriginal purchaser’s facility (in Canada, original purchaser’sfacility must be located within a 100 kilometers radius of anAuthorized Service Center) and without charge, anydefective component(s) of the printer, provided that this

| OKICOLOR 86

warranty service is performed by an authorized Oki Dataservice center or authorized third-party service organization.The printheads (LED imaging arrays) have a five (5) yearparts warranty from date of purchase. On-site replacement ofthe printheads is limited to one year from date of purchase.For the remaining printhead warranty period, replacementwill be at an authorized service center or authorized thirdparty service organization.

To make request or claim for service under this LimitedWarranty, contact your Oki Data Authorized Dealer,authorized third-party service provider, or Oki Data.

Oki Data will attempt to fix the problem over the telephoneprior to scheduling an on-site visit. It will be theresponsibility of the owner to install any warrantyreplacement consumable (drum or toner) or other end userreplaceable item as supplied by Oki Data.

A written receipt for the product, showing the date ofpurchase, place of purchase, and both the model and serialnumbers of this printer must accompany any request or claimfor work to be performed under this Limited Warranty. In theevent a service request is verified by Oki Data over thephone, a mailed or faxed copy of the written purchase receiptis required to verify in-warranty coverage prior to schedulingan on-site repair.

This Limited Warranty shall not apply if the product has beendamaged due to abuse, misuse, misapplication, accident, oras a result of service or modification by any other than anauthorized Oki Data service center.

THERE ARE NO EXPRESS WARRANTIES OTHER THANTHOSE ON THE FACE HEREOF AND DESCRIBED ABOVE.NO WARRANTIES, WHETHER EXPRESS OR IMPLIED,INCLUDING, BUT NOT LIMITED TO, ANY IMPLIEDWARRANTIES OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE, SHALL EXTEND BEYONDTHE RESPECTIVE WARRANTY PERIOD DESCRIBEDABOVE. Some states do not allow limitations on how longan implied warranty lasts, so the above limitation may notapply to you.

OKI DATA SHALL NOT BE RESPONSIBLE OR LIABLEFOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIALDAMAGES OR LOSS ARISING FROM THE USE OF THISPRODUCT. Some states do not allow the exclusion orlimitation of incidental or consequential damages, so theabove limitation may not apply to you.


Additional information on obtaining service under thisLimited Warranty is available by contacting the OKI DATAdealer from whom the product was purchased, by contactingOki Data directly at 1-800-654-3282 (1-800-OKI-DATA),United States and Canada, English and French only, or1-856-222-5276 (Spanish only), or by contacting one of thelisted service locations.

This Limited Warranty applies to this Oki Data printer.However, the procedure for obtaining service may varyoutside of the continental United States. Contact your OkiData dealer for such warranty service information.

This warranty gives you specific legal rights and you mayalso have other rights, which vary from state to state.

| OKICOLOR 88

Limited Warranty—Latin America

Oki Data Americas, Inc. (Oki Data) warrants this printer to befree from defect in material and workmanship and willremedy any such defect according to the terms of this LimitedWarranty. This Limited Warranty does not extend to networksetup, application conflicts, or consumable items including,but not limited to, image drum cartridges, toner cartridges,fuses, etc.

Consumables are covered separately under individualconsumable warranties. Please refer to the appropriateconsumable item’s warranty for further information.

Oki Data will repair (or at its option, replace) at no charge,any defective component(s) of the Printer for one (1) yearfrom the date of purchase except for the printheads (LEDimaging arrays), which are warranted for a period of five (5)years from date of purchase. This Limited Warranty extendsto the original purchaser only.

To make a request or claim for service under this LimitedWarranty, the original purchaser must return the Oki DataProduct to Oki Data or an authorized Oki Data service centerwithin the country purchased. The purchaser returning theproduct for repair must pay for all transportation charges tothe repair center. A written receipt for the Product, showingthe date of purchase, dealer’s name, and both the model andserial numbers of the Oki Data Product must accompany anyrequest or claim for work to be performed under this LimitedWarranty.

This Limited Warranty shall not apply if the product has beendamaged due to abuse, misuse, misapplication, accident, oras a result of service or modification by any other than anauthorized Oki Data service center.

THERE ARE NO EXPRESS WARRANTIES OTHER THANTHOSE ON THE FACE HEREOF AND DESCRIBED ABOVE.NO WARRANTIES EXPRESS OR APPLIED, INCLUDING,BUT NOT LIMITED TO, ANY PARTICULAR PURPOSE,SHALL EXTEND BEYOND THE RESPECTIVEWARRANTY PERIOD ABOVE OF ONE (1) YEAR.

Overview


Oki Data DepotService Centers

Authorized Service Providers

Oki Data has over 2,000 local Authorized Service Providersin North and South America.

For the most comprehensive, up-to-date listing of Oki Dataauthorized Service Centers:

• Consult our web site at www.okidata.com• In the U.S. and Canada, call 1-800-654-3282

(1-800-OKI-DATA) English and French only.• In Latin America, contact the Latin America Service

Coordinator at Oki Data’s Corporate Headquarters at856-222-5276 (Spanish only).

United StatesOki Data Americas, Inc.2020 Bishops Gate Blvd.Mt. Laurel, NJ 08054Phone: 800-654-3282 (800-OKI-DATA)U.S. and Canada, English and French only+856-235-2600 (Latin America)Fax: 856-222-5247 (U.S. and Canada)856-222-5260 (Latin America)

CanadaOki Data Americas, Inc.2735 Matheson Blvd. East, Unit 1Mississauga, OntarioCanada L4W 4M8Phone: 800-654-3282 (800-OKI-DATA)English and French onlyFax: 905-238-4427

| OKICOLOR 810

BrazilOki Data do Brasil, Ltda.Av. Leonardo da Vinci, 1178/1182JabaquaraSao Paulo, BrazilPhone: 55-11-5011-1518Fax: 55-11-5012-0267

MexicoOki Data de Mexico, S.A. de C.V.Av. Insurgentes 1700 – 7 PisoCol. Florida 01030Phone: (525) 661-6860Fax: (525) 661-5861

Overview


Important SafetyInformation

Your Oki Data printer has been carefully designed to giveyou years of safe, reliable performance. As with all electricalequipment, there are a few basic precautions you should taketo avoid hurting yourself or damaging the printer.

• Carefully read the provided setup and operatinginstructions.

• Save all provided documentation for future reference.• Read and follow all warning and instruction labels on the

printer itself.• Turn off the printer before opening printer covers or

replacing consumables.• Unplug the printer before you clean it. Use only a damp

cloth; do not use liquid or aerosol cleaners.• Place your printer on a firm, solid surface. If you put it on

something unsteady, it may fall and be damaged. If youplace it on a soft surface, such as a rug, sofa, or cushion,the vents may be blocked, causing the printer to overheat.

• Protect your printer from overheating. Make sure noobstructions block the openings of the printer. Do not putthe printer on or near a heat source (such as a radiator orheat register). Keep the printer out of direct sunlight.Allow enough room around the printer for adequateventilation and easy access to the paper trays. If you putthe printer in any kind of enclosure, make sure theenclosure is properly ventilated.

• Do not use your printer near water. Do not spill liquid ofany kind into it.

• Be certain that your power source matches the rating listedon the back of the printer. If you are not sure, check withyour dealer or with your local power company.

• Your printer has a grounded, three-prong plug as a safetyfeature. This plug only fits into a grounded outlet. If theplug does not fit, the outlet may be an older, non-grounded type. Contact an electrician to have the outletreplaced. Do not use an adapter to defeat the grounding.

| OKICOLOR 812

• Install the printer near an easily accessed power outlet.• Avoid damaging the power cord. Do not put anything on

it or place it where it will be walked on. If the cordbecomes damaged or frayed, replace it immediately.

• If you are using an extension cord or power strip with theprinter, make sure that the total of the amperes required byall the equipment on the extension is less than theextension’s rating. The total ratings of all equipmentplugged into the outlet should not exceed 15 amperes.

• Do not poke anything into the ventilation slots of theprinter. You could get an electrical shock or causehazardous electrical arcing, which could cause a fire.

• Aside from the routine maintenance described in thedocumentation, do not try to service the printer yourself.Removing the cover may expose you to shocks or otherhazards.

• Do not make any adjustments other than those outlined inthe documentation. You may cause damage that willrequire extensive repair work. The provideddocumentation explains how to get your printer servicedby qualified Oki Data technicians.

If anything happens that indicates that your printer is notworking properly or has been damaged, unplug itimmediately and follow the procedures in the provideddocumentation for having your printer serviced.

Here are some of the things to look for.

• The power cord or plug is frayed or damaged.• Liquid has been spilled into the printer, or the printer has

been exposed to water.• The printer has been dropped, or the cabinet is damaged.• The printer does not function normally when you are

following the operating instructions.

Overview


RegulatoryInformation

Federal CommunicationsCommission Radio FrequencyInterference Statement for 120-VoltModels

WARNING: This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuantto Part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference ina residential installation. This equipment generates, uses,and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may causeharmful interference to radio communications. However,there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be

determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or moreof the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the

receiver.• Plug the unit into an outlet on a circuit different from that

to which the receiver is connected.• Consult the dealer or an experienced radio/television

technician for help.It is the responsibility of the user to obtain the requiredshielded cable in order to ensure compliance of thisequipment with FCC regulations.

Changes or modifications not expressly approved by OkiData may void your authority to operate this device.

| OKICOLOR 814

Federal CommunicationsCommission Radio FrequencyInterference Statement for 230/240-Volt Models

WARNING: This equipment has been tested and found tocomply with the limits for a Class A digital device, pursuantto Part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference ina commercial environment. This equipment generates, uses,and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may causeharmful interference to radio communications. Operation ofthis equipment in a residential area is likely to cause harmfulinterference in which case the user will be required to correctthe interference at his own expense.

It is the responsibility of the user to obtain the requiredshielded cable in order to ensure compliance of thisequipment with FCC regulations.

Changes or modifications not expressly approved by OkiData may void your authority to operate this device.

Industry Canada Radio InterferenceStatement for 120-Volt Models

This Oki Data apparatus complies with the Class B limits forradio interference as specified in the Industry Canada RadioInterference Regulations.

Industry Canada Radio InterferenceStatement for 230/240-Volt Models

This Oki Data apparatus complies with the Class A limits forradio interference as specified in the Industry Canada RadioInterference Regulations.


European Union Council of theEuropean Communities Statement ofElectromagnetic Conformance for230/240-Volt Models

This product complies with the requirements of the councilDirective 89/336/EEC on the approximation of the laws ofthe member states relating to electromagnetic compatibility.

European Union Council of theEuropean Communities Statement ofSafety Conformance for 230/240-Volt Models

This product is in conformity with Directive 73/23/EEC onthe harmonization of the laws of Member States relating toelectrical equipment designed for use within certain voltagelimits.

Federal CommunicationsCommission Declaration ofConformity for 120 Volt Models

1. Product Identification

OKICOLOR 8, model N31001A

2. Statement

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received,including interference that may cause undesiredoperation.

3. Responsible Party

Oki Data Americas, Inc.

2000 Bishops Gate Boulevard

Mt. Laurel, NJ 08054-4620

1-800-654-3282 (1-800-OKI-DATA)

United States and Canada, English and French Only

Overview

| OKICOLOR 816

SpecificationsFor additional specifications (including General, Physical,Interface, Print Media, Fonts, and Commands) refer to the on-line User’s Guide.

Electrical

Voltage120 V: 120 VAC +5.5%, -15%230 V: 230VAC +/- 10%

Frequency50/60 Hz +/- 2%

PowerIdle

Approximately 70 W

Operating

Approximately 230 W

Peak

Approximately 980 W

Power Save Mode

Approximately 32 W


Environmental

TemperatureOperating

Maximum Permissible

50 to 90° F10 to 32° C

Best Color Print Quality

63 to 81° F17 to 27° C

Power Off

32 to 109° F0 to 43° C

Storage (Packed)

14 to 109° F-10 to 43° C

HumidityOperating

Maximum Permissible

20 to 80% Relative Humidity

Best Color Print Quality


Power Off


Storage (Packed)


Overview

| OKICOLOR 818

Material Safety DataSheet

No. 58334601

Applies to Black Toner, Type C1,P/N 40370601 (1.8 K Yield) andP/N 41012301 (3 K Yield)

Revised September, 1999

For more information, contact Oki Data at:

2000 Bishops Gate Blvd.

Mount Laurel, NJ 08054-4620

United States of America

Emergency Information1-800-654-3282 (1-800-OKI-DATA)

United States and Canada, English and French only

Emergency First Aid Procedures

Toner gets on the skinWash with plenty of soap and cool water.

Toner swallowed (ingested)Seek medical attention immediately.

Toner inhaledRemove person to fresh air and seek medical attention. Ifperson is not breathing, give artificial respiration. If person’sbreathing is difficult, give oxygen.

Toner gets in the eyesFlush eyes with large quantities of cool water for 15 minutes,keeping the eyelids open with fingers. Seek medicalattention.

! Small amounts of toner on skin or clothing can easilybe removed with soap and cold water (hot water makestoner harder to remove).


Hazardous IngredientsCarbon Black (4% by weight)CAS# 1333-86-4OSHA TWA 3.5 mg/m3

ACGIH TLV 3.5 mg/m3

Physical DataMelting Point: Not available

Softening Point: 122 to 129°C (252 to 264°F)

Boiling Point: Not applicable

Vapor Pressure: Not applicable

Vapor Density (Air=1): Not available

Evaporation Rate (Butyl Acetate=1): Not applicable

Specific Gravity (H2O=1): 1.16

Solubility in water: Insoluble

Appearance and odor: Black fine powder, no odor

Fire and Explosion Hazard DataFlash Point (Method Used): Not applicable

Flammable Limits

Lower Explosive Limit: Not known

Upper Explosive Limit: Not known

Extinguishing Media: CO2, Dry Chemical, or Foam

General Fire Hazards: Minimal fire hazard. Material isself-extinguishing.

Special Fire Fighting Procedures: Not provided

Unusual Fire and Explosion Hazards: Not applicable

| OKICOLOR 820

Health Hazard DataRoutes of Entry: Inhalation, Ingestion, Eyes, Skin.

1 Carbon Black

Group 2B “Possible Carcinogen”; IARC

Evidence of development of lung tumors in rats receivingchronic inhalation exposure to free carbon black at levelsthat induce particle overload of the lung. Studiesperformed in animal models other than rats have notdemonstrated an association between carbon black andlung tumors. A two-year cancer bioassay using a typicaltoner preparation containing carbon black demonstratedno association between toner exposure and tumordevelopment in rats.

In a study in rats by chronic inhalation exposure to atypical toner, a mild to moderate degree of lung fibrosiswas observed in 92% of the rats in the high concentration(16 mg/m3) exposure group, a mild degree of fibrosis wasnoted in 22% of the animals in the middle(4 mg/m3) exposure group, and no pulmonary change wasreported in the lower (1 mg/m3) exposure group, the mostrelevant level to potential human exposures.

Carbon black is designated hazardous according to OSHA29 CFR 1910.1200.

Reactivity DataStability: Stable

Polymerization: Will not occur.

Hazardous Decomposition Products: Combustion ordecomposition will generate phenol derivatives, carbonmonoxide and carbon dioxide at temperatures over 300°C(572°F).

Temperature: Not available

Incompatibility: Avoid exposure to strong oxidizers.


Spill Cleanup and Disposal

Spill CleanupSmall Spills

1 Sweep up spill.

Large Spills

1 Mix spilled material with a moist absorbent and place insuitable waste container. Nonhazardous under RCRA.

2 Wear protective gear: NIOSH/ MSHA approved dust/mistrespirator, rubber gloves, goggles (see below).

Waste DisposalFollow appropriate federal, state and local regulations.Prevent release of material into natural environment.

Safe Handling and UseRespiratory Protection: Not normally required. For large

spills, use NIOSH/MSHA approved full face-piecerespirator with HEPA cartridge during cleanup.

Protective Gloves and/or Eye Protection: Not normallyrequired. For large spills, use rubber gloves and chemicalworker’s goggles during cleanup.

Ventilation: Outside of normal ventilation, not normallyrequired.

Other Protective Equipment and/or Hygienic Practices:None

| OKICOLOR 822

Special PrecautionsPrecautions for Handling or Storage: Protect from high

heat. Store in a well-ventilated area at temperature below35°C (95°F) to prevent caking.

Other Precautions: None

The information contained in this MSDS is based on dataconsidered accurate; however, no warranty is expressed orimplied regarding the accuracy of these data or the results tobe obtained from the use thereof. Vendor assumes noresponsibility for injury to vendee or third person partyproximately caused by the product if reasonable safetyprocedures are not adhered to as stipulated in the MSDS.Furthermore, vendor assumes no responsibility for injury tovendee or third person party proximately caused by abnormaluse of the product even if reasonable safety procedures arefollowed. Additionally, vendee assumes the risk of his use ofthe product.

Overview


Material Safety Data Sheet

No. 58334701

Applies to Cyan Toner, Type C1,P/N 40370604 (1.8 K Yield) andP/N 41012304 (3 K Yield)














| OKICOLOR 824

Hazardous IngredientsNone, according to OSHA 29 CFR 1910.1200 and DOT 49CFR 172.101.

Physical DataMelting Point: Not availableSoftening Point: 101 to 107°C (214 to 225°F)Boiling Point: Not applicableVapor Pressure: Not applicableVapor Density (Air=1): Not availableEvaporation Rate (Butyl Acetate=1): Not availableSpecific Gravity (H

2O=1): 1.16

Solubility in water: InsolubleAppearance and odor: Cyan fine powder, no odor


Flammable Limits




General Fire Hazards: Minimal fire hazard. Material isself-extinguishing



Health Hazard DataRoutes of Entry: Inhalation, Ingestion, Eyes, Skin









1 Sweep up spill.

Large Spills


2 Wear protective gear: NIOSH/ MSHA approved dust/mistrespirator, rubber gloves, goggles.


| OKICOLOR 826










Overview



No. 58334801

Applies to Magenta Toner, Type C1,P/N 40370603 (1.8 K Yield) andP/N 41012303 (3 K Yield)














| OKICOLOR 828







Evaporation Rate (Butyl Acetate=1): Not available



Appearance and odor: Magenta fine powder, no odor


Flammable Limits
















1 Sweep up spill.

Large Spills




| OKICOLOR 830










Overview



No. 58334901

Applies to Yellow Toner, Type C1,P/N 40370602 (1.8 K Yield) andP/N 41012302 (3 K Yield)














| OKICOLOR 832







Evaporation Rate (Butyl Acetate=1): Not available



Appearance and odor: Yellow fine powder, no odor


Flammable Limits
















1 Sweep up spill.

Large Spills




| OKICOLOR 834










Overview


Material Safety DataSheet

No. 58335201

Applies to Oil Roller, P/N 40645301









Oil gets on the skinWipe off with dry cloth or towel, then wash with detergent.

Oil swallowed (ingested)Wash mouth thoroughly with water. NEVER give anything bymouth to a person who is unconscious. Seek medicalattention immediately.

Oil gets in the eyesFlush eyes with large quantities of cool water for 15 minutes,keeping the eyelids open with fingers.

| OKICOLOR 836

Hazardous IngredientsNone (silicone fluid).

Physical DataMelting Point: Not applicableSoftening Point: Not applicableBoiling Point: Not applicableVapor Pressure: Not applicableVapor Density (Air=1): Not applicableEvaporation Rate (Butyl Acetate=1): Negligible @ 25°C(77°F)Specific Gravity (H

2O=1): 0.965 @ 25°C (77°F)

Solubility in water: Insoluble (<1 ppm)Appearance and odor: Colorless, transparent liquid. Noodor.

Fire and Explosion Hazard DataFlash Point (Method Used): 300°C (572°F) minimum (open

cup)

Flammable Limits




General Fire Hazards: Not considered flammable norcombustible, but will burn if involved in a fire.

Special Fire Fighting Procedures: Not required

Unusual Fire and Explosion Hazards: None

Health Hazard DataRoutes of Entry: Ingestion, Eyes, Skin

Eye Irritation: May cause transitional slight eye irritation.

Carcinogenicity: NTF/IARC/OSHA, not listed. No evidenceof carcinogenicity in laboratory animals.

Mutagenicity: No evidence

Chronic Toxicity: No significant effects observed.




Hazardous Decomposition Products: None.

Temperature: Not available.

Incompatibility: None.


Spill CleanupScrape up with cardboard or rag and place in waste container.

Waste DisposalFollow appropriate federal, state and local regulations.

Can be burned in a chemical incinerator equipped with anafter burner and scrubber.

Safe Handling and UseRespiratory Protection: Not normally required. This product

can generate formaldehyde at approximately 150°C(300°F) and above in the presence of air: If product isexposed to such high temperatures, respiratory protectionis required.

Protective Gloves and/or Eye Protection: Not normallyrequired. For spills, use plastic film or rubber gloves andchemical worker’s goggles during cleanup.

Ventilation: Outside of normal ventilation, not normallyrequired. This product can generate formaldehyde atapproximately 150°C (300°F) and above in the presenceof air: If product is exposed to such high temperatures,adequate ventilation must be provided.

Other Protective Equipment and/or Hygienic Practices:Wash hands after handling.

| OKICOLOR 838

Special PrecautionsPrecautions for Handling or Storage: Store in a cool place.

Protect from high heat. This product can generateformaldehyde at approximately 150°C (300°F) and abovein the presence of air. Formaldehyde is a skin andrespiratory sensitizer, eye and throat irritant, acutetoxicant and potential cancer hazard.Do not lay the container on its side.Avoid contact with eyes and prolonged or repeatedcontact with skin.Do not puncture or cut the container.

Other Precautions: Keep out of the reach of children.


English Warranty, Regulatory Information, and...

Documents

Transcript of English Warranty, Regulatory Information, and...