ENGINE INSTALLATION AND BREAK-IN
-
Upload
veda-delgado -
Category
Documents
-
view
35 -
download
0
description
Transcript of ENGINE INSTALLATION AND BREAK-IN
![Page 1: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/1.jpg)
© 2011 Pearson Education, Inc.All Rights Reserved
Automotive Technology, Fifth EditionJames Halderman
ENGINE INSTALLATION AND BREAK-IN
38
![Page 2: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/2.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-1 A partially melted electrical connector indicates that excessive current flow was present. The cause of the excessive current should be located and corrected before the engine is started.
![Page 3: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/3.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-2 Bell housing alignment dowel pins are used to ensure proper alignment between the engine block and the transmission.
![Page 4: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/4.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
TECH TIP: The Headless Bolt Trick Sometimes parts do not seem to line up correctly. Try this tip the next time. Cut the head off of extra-long bolts that are of the same diameter and thread as those being used to retain the part, such as a transmission. - SEE FIGURE 38–3 . Use a hacksaw to cut a slot in this end of the guide bolts for a screwdriver slot. Install the guide bolts; then install the transmission. Use a straight-blade screwdriver to remove the guide bolts after securing the transmission with the retaining bolts.
![Page 5: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/5.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-3 Headless long bolts can be used to help install a transmission to the engine.
![Page 6: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/6.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-4 The internal splines inside the torque converter must be properly aligned with all of the splines of the automatic transmission.
![Page 7: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/7.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-5 It is often easier to install all of the accessory drive belts before the engine is installed in the vehicle.
![Page 8: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/8.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-6 A fixture installed that is used as a place to attach the hosting chains.
![Page 9: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/9.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
FREQUENTLY ASKED QUESTION: What Is Break-In Engine Oil? Many years ago, vehicle manufacturers used straight weight such as SAE 30 nondetergent engine oil as break-in oil. Today, the engine oil recommended for break-in (running in) is the same type of oil that is recommended for use in the engine. No special break-in oil is recommended or used by the factory in new vehicles. Always use the specified viscosity oil as recommended by the vehicle manufacturer.
![Page 10: ENGINE INSTALLATION AND BREAK-IN](https://reader035.fdocuments.in/reader035/viewer/2022062221/56813024550346895d95a9bf/html5/thumbnails/10.jpg)
38 ENGINE INSTALLATION AND BREAK-IN
Automotive Technology, Fifth EditionJames Halderman
© 2011 Pearson Education, Inc.All Rights Reserved
Figure 38-7 Even though the dash gauge may show normal operating temperature, a scan tool or an infrared pyrometer can also be used to verify proper coolant temperature.