Emulsion Breaker 210 Product Sheet

8/3/2019 Emulsion Breaker 210 Product Sheet

1/7

Manufactured by :

Information Technology Solutions

PRODUCT DESCRIPTION

Chemiphase are proud to launch our latest

development in biodiesel technology, ademulsifier specifically designed to be used with

biodiesel production to remove excess water

content in biodiesel. Emulsion Breaker 210 can

also be used in vegetable oils to remove water.

Emulsion Breaker 2010 has been developed for

the Biodiesel Water Washing Process. This

product will knock out stubborn emulsions

and "rag layers" rapidly. To achieve the best

results with this product we recommend heating

both the biodiesel and water above 55 deg C

before adding the product, please ensure the

EB 2010 is well mixed in the biodiesel.

Emulsion Breaker 210 is designed to aid removal

of wash water from bio diesel production.

Emulsion Breaker is to be used when water

washing takes place.

PACK SIZES

AVAILABLE

20 LITRES

200 LITRES

1000 LITRES

10,000 LITRES

20,000 LITRES

TECHNICAL

SUPPORT

Chemiphase wi l l

of fer on- s i te

technical support

dur ing al l s tages of

product ion.

Technical supportincludes on-s i te

test ing and resul ts .

PRODUCT SAFETY

All Chemiphase

products are

thoroughly

researched and

tested. All products

are also COSHH

registered and

come complete with

delivery.

For more information

on any of our

products or services

please visit us on the

Web at:

www.chemiphase.co.uk

Phone :(08456) 432900

Email :[email protected]

Biodiesel Additive to Remove Water&Break Emulsions from Biodiesel

Emulsion Breaker 210

Emulsion Breaker 210 will speed up th

splitting of the oil and water separatio

producing two distinct layers.

Typical dilution rate is 2-4 Litres per 1000 litr

of water added, but this dependant upo

the quality of the raw oil initially used. Onc

mixed well, turn off the mixing equipme

then leave to stand to ensure the f

separation occurs prior to running the wat

layer off the bottom of the tank.

For more information on this product plea

contact us directly on (08456) 432900 an

we would be more than happy to help.
http://www.chemiphase.co.uk/http://www.chemiphase.co.uk/http://www.chemiphase.co.uk/


2/7

PRODUCT RANGE :

BIODIESEL ADDITIVES

ALLKLEAR 400

Biodiesel antioxidant to control

oxidation levels in biodieselwhich can cause degradation

and damage to tank storage.

BIO-CONTROL 41

Biodiesel biocide to control

micro-biological growth in

biodiesel.

BIOBOOST 1000

Biodiesel cetane enhancing

product which increase

performance and efficiency.

PH CORRECT

pH correction agent to control

the pH of the biodiesel after

the reaction stage.

COLDFLOW 402Pour point additive designed

for heavy oils like PME. SME,

Tallow.

CITRACLEAN

Excellent cleaning detergent

for areas where oil staining

and greasy floors are a

problem.


Emulsion Breaker 210 - Application

Once the biodiesel reaction has been completed, remove the Glycerine layer prior to

washing stage. Proceed to wash the biodiesel, with Emulsion Breaker 210 added to the warm

water. We suggest the water is first heated to approximately 40 degrees C. The correct level

of Emulsion Breaker 210 is then added to the warm water. This should be then mixed well to

ensure all of the Emulsion Breaker 210 has dispersed correctly. This aqueous mixture should

then be added to the bio diesel to remove the contaminants contained in the oil. Emulsion

Breaker 210 will rapidly bring about the oil/water splitting process.


3/7

Potassium (ppm)

0 hr hr 1 hrs

Control 35 29.5 19.3

409 15.5 6.5

CC 16.5 6.5

CC/N9 14.6 5.4

417 16.7 9.6

650 14.6 9.3

evision date: March 2011

CHEMIPHASE LTD

SAFETY DATA SHEET

EMULSION BREAKER 210

Emulsion Breaker 210 Test Methods :Pour PointASTM

D5950 (Deg C)

CFPPASTM D6371

(Deg C)

PACK S IZES

AVAILABLE

20 LITRES

200 LITRES

1000 LITRES

10,000 Tanker

20,000 Tanker

TECHNI CAL SUPPORT

Ch emiph ase wi l l

o f fer on- s i te

technical suppor t

du r in g a l l s tages o f

product ion .

Technical suppor t

in c lu des on s i te

test ing.

DISCLAIMER :The information and all

further technical advice

are based on our presen

knowledge and

experience. However,

they imply no liability or

other legal responsibility

on our part, including wi

regards to existing third

party intellectual proper

rights, especially patent

rights. In particular, no

warranty, whether

express or implied of

guarantee of product

properties is intended or

implied. We reserve the

right to make any

changes according to

technological progress o

further developments. Thcustomer is not released

from the obligation toconduct careful

inspection and testing o

incoming goods.

Performance of theproduct described herei

should be verified by

testing, which should be

carried out by qualified

experts in the sole

responsibility of the

customer.

Conclusion

From the range of results you can see a clear drop in the potassium levels of the biodiesel

samples tested. This indicates that due to the potassium being insoluble in the oil it has

remained with the water and if the potassium levels have dropped off the water content has

greatly been reduced. A clear indicator of the Emulsion Breaker range break tight emulsions

found in this sample of biodiesel. The range of additives used are the major constituents of the

Emulsion Breaker210. The results show a very quick reduction in water content and a greatly

reduced water content in comparison with the control sample taken. The control sample

contains no additives at all.

Test Results from a Current Customer using



4/7

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND COMPANY UNDERTAKING

RODUCT NAME: EMULSION BREAKER 210

RODUCT Description: Concentrated Oil Based Demulsifier -NEW FORMULATION MARCH 2005

APPLICATION BIO DIESEL PRODUCTION

UPPLIER Chemiphase LtdPO Box 168OrmskirkL40 6ZXTel: 00 44 1744 886622Fax: 00 44 1744 886633

MERGENCY TELEPHONE (24 HR) 00 44 (0) 1744 886622

2. COMPOSIITON INFORMATION ON INGREDIENTS

AME EC No CAS No CONTENT CLASSIFICATION

-BUTOXYETHANOL 203-905-0 111-76-2 8-15% XnR20/21/22 Xi,R36/38YLENE 215-535-7 1330-20-7 15-22% R10 Xn, R10/R20/21 Xi,

R38 & S16

he Full Text for all R- Phrases are displayed in Section 16

3. HAZARDS IDENTIFICATION

armful by inhalation, in contact with skin and if swallowed. Irritating to eyes and skin.

LASSIFICATION Xn; R20/21/22. Xi;R36/38

4. FIRST AID MEASURES

ENERAL INFORMATION

Move the exposed person to fresh air at once. Get medical attention if any discomfort continues.NHALATION

Move the exposed person to fresh air at once. If respiratory problems, artificial respiration/oxygen. Keep the affected person warm and at rest. Get pmedical attention.NGESTIONEVER MAKE AN UNCONSCIOUS PERSON VOMIT OR DRINK FLUIDS! Remove victim immediately from source of exposure. Rinse mouth thoroughly. Proet affected person to drink large volumes of water to dilute the swallowed chemical. DO NOT induce vomiting. Get medical attention immediately.KIN CONTACTemove affected person from source of contamination. Promptly wash contaminated skin with soap or mild detergent and water. Promptly remove clothoaked through and wash as above. Get medical attention immediately.YE CONTACT

Make sure to remove any contact lenses from the eyes before rinsing. Promptly wash eyes with plenty of water while lifting the eyelids. Continue to rinse east 15 minutes and get medical attention.

5. FIRE FIGHTING MEASURES

XTINGUISHING MEDIAse: Powder, Carbon dioxide (CO2). Water spray. FoamPECIAL FIRE FIGHTING PROCEDURESvoid water in straight hose stream; will scatter and spread fire. Use water to keep fire exposed containers cool and disperse vapours. Keep run-off water ewers and water sources. Dike for water control.PECIFIC HAZARDSy heating and fire, irritating vapours/gases may be formed.ROTECTIVE MEASURES IN FIRE

Wear personal protective equipment. Wear self-contained breathing apparatus.

6. ACCIDENTAL RELEASE MEASURES

ERSONAL PRECAUTIONSWear protective clothing as described in Section 8 of this safety data sheet. Avoid contact with skin and eyes. Provide adequate ventilation.NVIRONMENTAL PRECAUTIONS

o not discharge into drains, watercourses or onto the ground.


5/7

PILL CLEAN UP METHODStop leak if possible without risk. Absorb in vermiculite, dry sand or earth and place into containers. Containers with collected spillage must be properly la

with correct contents and hazard symbol. Do not contaminate water sources or sewer.

7. HANDLING AND STORAGE

sage precautionsvoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours. Use approved respirator if air contamination is above accepted level.TORAGE PRECAUTIONStore in tightly closed original container in a cool dry well-ventilated place. Use container made of : Stainless steel. Suitable plastic material. Do NOontainer made of: Carbon steel.

8. EXPOSURE CONTROL/PERSONAL PROTECTION

Name Std LT - ppm LT mg/m3 ST - ppm ST mg/m3

YLENE OES 50 ppm (Sk) 220 mg/m3 (Sk) 100 ppm(Sk) 441 mg/m3(Sk)

-BUTOXYETHANOL OES 25 PPM(Sk) 50 ppm(Sk)

NGREDIENT COMMENTSOES = Occupational Exposure Standard. 2 Butoxyethanol (EGMBE) has a Biological Monitoring Guidance Value. See UK HSE EH40 Table 3

ROTECTIVE EQUIPMENToggles and Gloves

NGINEERING MEASURESrovide adequate general and local exhaust ventilation

ESPIRATORY EQUIPMENT

o specific recommendation made, but respiratory protection may still be required under exceptional circumstances when excessive air contamination eWear respiratory protection with combination filter (dust and gas filter).

AND PROTECTIONse protective gloves. Rubber, neoprene or PVC. The most suitable glove must be chosen in consultation with the gloves supplier, who can inform aboureakthrough time of the glove material. Be aware that the liquid may penetrate the gloves. Frequent change is advisable.

YE PROTECTIONWear approved safety goggles.

OTHER PROTECTIONWear appropriate clothing to prevent any possibility of liquid contact and repeated or prolonged vapour contact.

YGIENE MEASURESO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet. Wash promptly with soap and water ecomes contaminated. Promptly remove any clothing that becomes contaminated. When using do not eat, drink or smoke.

9. PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE Liquid

OLOUR Slightly hazy

ODOUR: Slight Aromatic Boiling Point/ range(OC) 137-143

MELTING POINT (Oc) Pour Point , -20 RELATIVE DENSITY OC

Ph, VALUE,

DILUTED SOLUTION 6.5-8.5, 5% in water VISCOSITY < 100 mPas @ 20oC

LASH POINT (OC) 25 AUTOFlammability (OC) 480

10. STABILITY AND REACTIVITY

TABILITYtable under normal temperature conditions.

ONDITIONS TO AVOIDvoid heat, flames and other sources of ignition

MATERIAL TO AVOIDtrong oxidising substances. Strong acids

AZARDOUS DECOMPOSITION PRODUCTS

uring fire, toxic gases (CO, CO2) are formed.


6/7

11. TOXICOLOGICAL INFORMATION

OXIC DOSE 1 LD50 >4000 mg/kg (oral rat)

NHALATIONarmful by inhalation. In high concentrations, vapours are anaesthetic and may cause headache, fatigue, dizziness and central nervous system effects. Upp

espiratory irritation. Vapours may cause headache, fatigue, dizziness and nausea.

NGESTIONarmful if swallowed. Gastrointestinal symptoms, including upset stomach. May cause nausea, headache, dizziness and intoxication.

KIN CONTACT

armful in contact with skin. Irritating to skin.

YE CONTACTrritating to eyes. Spray and vapour in the eyes may cause irritation and smarting.

Other Health Effectso sensitising effects known.

12. ECOLOGICAL INFORMATION

COTOXICITYhe product components are not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can havarmful or damaging effect on the environment.

MOBILITYhe product is insoluble in water

IOACCUMULATIONo data available

EGRADABILITYhe product is expected to be biodegradable

WATER HAZARD CLASSIFICATIONWGK 1

13. DISPOSAL CONSIDERATIONS

ENERAL INFORMATIONmpty containers should be taken for local recycling, recovery or waste disposal

ISPOSAL METHODSecover and reclaim or recycle, if practical. Do not allow runoff to sewer, waterway or ground. Dispose of waste and residues in accordance with local authoequirements.

WASTE CLASSor this product, in accordance with the European Waste Catalogue (EWC), a catalogue number cannot be given because the customer has to lay down theurpose first. The catalogue number has to be given according to the local waste removal processes.

14. TRANSPORT INFORMATION

GENERAL ADR/RID UN no: 1307 ADR Class: 3

Packing Group: III Classification code: F1

Shipping name n/a

Labelling: 3 Hazard ID no: 30IMDG/IMO UN no: 1307 Class: 3

Packing Group: III EMS:F-E, S-D

Marine Pollutant: NO Labelling: 3

IATA/ICAO UN no: 1307 Class: 3

Packing Group: III Packing Instructions; 309(p&CA):310(CAO)

Marine Pollutant: NO Labelling: 3


7/7

15. REGULATORY INFORMATION

ABELLING

Harmful

ONTAINS 2-BUTOXYETHANOL, Xylene

ISK PHRASES R20/21/22 Harmful by inhalation, in contact with skin and if swallowed

R10 FlammableR36/38 Irritating to eyes and skin

AFETY PHRASES S36/37 Wear suitable protective clothing and gloves

S16 Keep away from sources of ignitionNO SMOKINGS60 This material and its container must be disposed of as hazardous waste

S23 Do not breathe vapour/spray

S26 In case of contact with eyes, rinse immediately with plenty of water and see medical advice

S51 Use only in well-ventilated areas

S24/25 Avoid contact with skin and eyes

K REGULATORY REFERENCESpproved Supply List

TATUTORY INSTRUMENTShemicals (Hazard Information and Packaging) RegulationsPPROVED CODE OF PRACTICElassification and Labelling of Substances and Preparations Dangerous for Supply. Safety Data Sheets for Substances and Preparations.

UIDANCE NOTESOccupational Exposure Limits EH40. Approved guide to the classification and labelling of substances and preparations dangerous for supply.

16. OTHER INFORMATION

EVISION COMMENTSeneral revision

SSUED BYES

EVISION DATE MARCH 2008

EVISED SDS GENERATED MARCH 2005

ISK PHRASES IN FULL

10 Flammable

20/21 Harmful by inhalation and in contact with skin20/21/22 Harmful by inhalation, in contact with skin and if swallowed36/38 Irritating to eyes and skin38 Irritating to skin

X

DISCLAIMERThe information provided in this SDS is correct to the best of our knowledge, information and belief at the date of its publication. Theinformation given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal, and release andis not be considered a warranty or quality specification. The information relates only to the specific material designated and may notbe valid for such material used in combination with any other materials or in any process unless specified in the text.

Emulsion Breaker 210 Product Sheet

Documents

Transcript of Emulsion Breaker 210 Product Sheet