EMPowered™ - Emtek Products, IncSet up a lock Connected by August: 1. Install DoorSense 2. Connect...
Transcript of EMPowered™ - Emtek Products, IncSet up a lock Connected by August: 1. Install DoorSense 2. Connect...
EMPowered™ Motorized Smart Lock Upgrade
- Connected by August
www.emtek.com
2
EMPowered™ Motorized Smart Lock Upgrade - Connected by August
Deadbolt
Sideplate
Tubular Sectional Entry Set
Tubular Monolithic/Full Length Entry Set
Hardware TroubleshootingDefinitionsProgramming TroubleshootingResetting Lock to Factory DefaultFactory SettingsCompliance
3
16
29
42
555556575758
3
DEA
DBO
LT
EMPowered™ Motorized Smart Lock Upgrade - Connected by August
Deadbolt
4
DEA
DBO
LT
What’s in the box
ITEM NO. DESCRIPTION QTY.1 EMPower Unit 1
1a August Module 11b Battery Cover 11c AA Batteries 41d M4-0.7 x 8mm Machine Screws 31e Interior Escutcheon 11f #10-32 x 2-1/8” Machine Screws 21g Mounting Plate 12 Deadbolt Latch 2-3/4” Backset 12 Deadbolt Latch 2-3/8” Backset 1
ITEM NO. DESCRIPTION QTY.3 Deadbolt Screw Guide 14 Deadbolt Trim 15 Deadbolt Extension Collar 16 Deadbolt Cylinder 17 #8 x 3/4” Wood Screws 48 Deadbolt Strike Plate 19 Deadbolt Security Plate 1
10 #10 x 3” Wood Screws 211 August Connect 112 August DoorSenseTM 1
1b
7 810 9
1d 1e
1a
1f
1g
1c
12
35 6
4
7 11 12
5
DEA
DBO
LT
Door Prep
Door Jamb Prep
214"
2-3/8"or
2-3/4"
.1" DiaEdge
Bore
1"
2-1/8" Dia.Bore
1/8” Deep
234"
1-1/8"
6
DEA
DBO
LT
Install Latch1
Note: Use only the supplied latch for proper
functionality.
!
7
DEA
DBO
LT
Install Lock Cylinder
Extension Collar required for thin doors
2
Must use screw guide
!
8
DEA
DBO
LT
Remove Battery Cover3
Loosen screw on bottom to remove cover.
9
DEA
DBO
LT
Install Interior Mounting Plate4
10
DEA
DBO
LT
Check Interior Mounting Plate Alignment5
Center tail piece in mounting plate holebefore tightening.
!
11
DEA
DBO
LT
Install Interior Escutcheon6
Bolt must be in retracted (unlocked) position
!
12
DEA
DBO
LT
Testing Operation7
13
DEA
DBO
LT
Bolt must be in retracted (unlocked) position before installing batteries.
Install Batteries8
!
14
DEA
DBO
LT
Handing the Lock9
To hand the lock, press the button until you hear one beep
15
DEA
DBO
LT
9
Set up a lock Connected by August:1. Install DoorSense™2. Connect your Smart Lock3. Set up an August Connect
Go to the August App to Complete Installation
Secure cover by tightening screw on bottom.
16
SIDEPLATE
EMPowered™ Motorized Smart Lock Upgrade - Connected by August
Keyed Sideplate
17
SIDEPLATE
What’s in the box
ITEM NO. DESCRIPTION QTY.1 EMPowered™ Unit 1
1a August Module 11b Battery Cover 11c AA Batteries 41d M4-0.7 x 8 mm Machine Screws 31e Interior Escutcheon 11f #10-32 x 2-1/8” Machine Screws 21g Mounting Plate 12 Interior Knob/Lever Assembly 13 #8-32 x 1-1/2” Machine Screws 24 Deadbolt Latch 2-3/4” Backset 14 Deadbolt Latch 2-3/8” Backset 15 Deadbolt Screw Guide 16 Sideplate Exterior Assembly 1
ITEM NO. DESCRIPTION QTY.7 #6 x 1” Oval Head Wood Screw 2 or 48 Deadbolt Extension Collar 19 Deadbolt Cylinder 1
10 Alignment Tool 111 Passage Latch 112 Rosette Mounting Plate 113 Latch Face Plate 114 #8 x 3/4” Wood Screws 815 Latch Strike Plate 116 Deadbolt Strike Plate 117 Deadbolt Security Plate 118 #10 x 3” Wood Screws 219 August Connect 120 August DoorSenseTM 1
1
2
3
1413
14
7
19 20
15
17
45
8 9
6
10
16
18
11
12
1b1d 1e
1a
1f
1g
1c
18
SIDEPLATE
234"
214"
1-1/8"
1-1/4"
214"
214"
5-1/2”
See Template
2-3/8"or
2-3/4"
1" Dia.Edge Bores
1"
2-1/8" Dia.Bores
23/4”
21/4”
21/4”
21/4”
51/2”
11/4”
11/8”
21/8” Dia.Bores
23/8” or
23/4”Door Prep
Door Jamb Prep
19
SIDEPLATE
Install Latches1
Note: Use only the supplied latch for proper
functionality.
!
20
SIDEPLATE
Install Interior Lever/Knob2
21
SIDEPLATE
Remove Battery Cover3
Loosen screw on bottom to remove cover.
22
SIDEPLATE
Install Lock Cylinder & Interior Mounting Plate4
Do not install the side plate mounting screws
until a later step.
Must use screw guide
!
!
Extension Collar required for thin doors
23
SIDEPLATE
Check Interior Mounting Plate Alignment5
Center tail piecein mounting platebefore tightening.
!
24
SIDEPLATE
Install Interior Escutcheon6
Bolt must be in retracted (unlocked) position
!
25
SIDEPLATE
Testing Operation7
Test thumb turn and lever function before installing the screws.
!
26
SIDEPLATE
Install Batteries8
Bolt must be in retracted (unlocked) position before installing batteries.
!
27
SIDEPLATE
Handing the Lock9
To hand the lock, press the button until you hear one beep
28
SIDEPLATE
10
Set up a lock Connected by August:1. Install DoorSense™2. Connect your Smart Lock3. Set up an August Connect
Go to the August App to Complete Installation
Secure cover by tightening screw on bottom.
29
TUBU
LAR EN
TRY SET - SECTIO
NA
L
EMPowered™ Motorized Smart Lock Upgrade - Connected by August
Sectional Entry Set
30
TUBU
LAR EN
TRY SET - SECTIO
NA
L
What’s in the box
ITEM NO. DESCRIPTION QTY.1 EMPower Unit 1
1a August Module 11b Battery Cover 11c AA Batteries 41d M4-0.7 x 8mm Machine Screws 31e Interior Escutcheon 11f #10-32 x 2-1/8” Machine Screws 21g Mounting Plate 12 Interior Knob/Lever Assembly 13 #8-32 x 1-1/2” Machine Screws 24 Deadbolt Latch 2-3/4” Backset 14 Deadbolt Latch 2-3/8” Backset 15 Deadbolt Screw Guide 16 Deadbolt Trim 1
ITEM NO. DESCRIPTION QTY.7 Deadbolt Extension Collar 18 Deadbolt Cylinder 19 Passage Latch 1
10 Latch Face Plate 111 Decorative Cap 112 #8-32 Flat head Machine Screw 113 Threaded Washer 114 #8 x 3/4” Wood Screws 815 Sectional Entry Set Assembly 116 Latch Strike Plate 117 Deadbolt Strike Plate 118 Deadbolt Security Plate 119 #10 x 3” Wood Screws 220 August Connect 121 August DoorSenseTM 1
14
20 2116
18
17
19
1b1d 1e
1a
1f
1g
1c
1
2
3
14
14
131211
4 5
7 86
910
15
31
TUBU
LAR EN
TRY SET - SECTIO
NA
L234"
214"
1-1/8"
1-1/4"
214"
214"
5-1/2”
See Template
2-3/8"or
2-3/4"
1" Dia.Edge Bores
1"
2-1/8" Dia.Bores
23/4”
21/4”
21/4”
21/4”
51/2”
11/4”
11/8”
21/8” Dia.Bores
23/8” or
23/4”Door Prep
Door Jamb Prep
32
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Install Latches1
Note: Use only the supplied latch for proper
functionality.
!
33
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Install Grip and Interior Lever/Knob2
34
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Remove Battery Cover3
Loosen screw on bottom to remove cover.
35
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Must use screw guide
Extension Collar required for thin doors
!
Install Lock Cylinder &Interior Mounting Plate4
36
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Check Interior Mounting Plate Alignment5
Center tail piece in mounting plate holebefore tightening.
!
37
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Install Interior Escutcheon6
Bolt must be in retracted (unlocked) position
!
38
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Testing Operation7
39
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Install Batteries8
Bolt must be in retracted (unlocked) position before installing batteries.
!
40
TUBU
LAR EN
TRY SET - SECTIO
NA
L
Handing the Lock9
To hand the lock, press the button until you hear one beep
41
TUBU
LAR EN
TRY SET - SECTIO
NA
L
10
Set up a lock Connected by August:1. Install DoorSense™2. Connect your Smart Lock3. Set up an August Connect
Go to the August App to Complete Installation
Secure cover by tightening screw on bottom.
42
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
EMPowered™ Motorized Smart Lock Upgrade - Connected by August
Monolithic/Full Length Entry Set
43
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
What’s in the box
ITEM NO. DESCRIPTION QTY.1 EMPowered™ Unit 1
1a August Module 11b Battery Cover 11c AA Batteries 41d M4-0.7 x 8mm Machine Screws 31e Interior Escutcheon 11f #10-32 x 2-1/8” Machine Screws 21g Mounting Plate 12 Interior Knob/Lever Assembly 13 #8-32 x 1-1/2” Machine Screws 24 Deadbolt Latch 2-3/4” Backset 14 Deadbolt Latch 2-3/8” Backset 15 Deadbolt Screw Guide 16 Entry Set Exterior Assembly 1
ITEM NO. DESCRIPTION QTY.7 Deadbolt Extension Collar 18 Deadbolt Cylinder 19 Passage Latch 1
10 Latch Face Plate 111 Decorative Cap 112 #8-32 Flat Head Machine Screw 113 Threaded Washer 114 #8 x 3/4” Wood Screws 815 Latch Strike Plate 116 Deadbolt Strike Plate 117 Deadbolt Security Plate 118 #10 x 3” Wood Screws 219 August Connect 120 August DoorSenseTM 1
14
19 2015
17
16
18
1b1d 1e
1a
1f
1g
1c
1
2
3
14
14
131211
45
7 8
6
9 10
44
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
234"
214"
1-1/8"
1-1/4"
214"
214"
5-1/2”
See Template
2-3/8"or
2-3/4"
1" Dia.Edge Bores
1"
2-1/8" Dia.Bores
23/4”
21/4”
21/4”
21/4”
51/2”
11/4”
11/8”
21/8” Dia.Bores
23/8” or
23/4”Door Prep
Door Jamb Prep
45
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Install Latches1
Note: Use only the supplied latch for proper
functionality.
!
46
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Install Grip and Interior Lever/Knob2
Must use screw guide
!
47
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Remove Battery Cover3
Loosen screw on bottom to remove cover.
48
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Install Lock Cylinder &Interior Mounting Plate4
Extension Collar required for thin doors
49
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Check Interior Mounting Plate Alignment5
Center tail piece in mounting plate holebefore tightening.
!
50
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Install Interior Escutcheon6
Bolt must be in retracted (unlocked) position
!
51
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Testing Operation7
52
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Install Batteries8
Bolt must be in retracted (unlocked) position before installing batteries.
!
53
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
Handing the Lock9
To hand the lock, press the button until you hear one beep
54
TUBU
LAR EN
TRY SET - MO
NO
LITHIC/FU
LL LENG
TH
10
Set up a lock Connected by August:1. Install DoorSense™2. Connect your Smart Lock3. Set up an August Connect
Go to the August App to Complete Installation
Secure cover by tightening screw on bottom.
55
Hardware Troubleshooting
SymptomDoor is binding
Bolt will not deadlock
Bolt does not extend or
retract smoothly
• Check that door and frame are properly aligned and door is free swinging.
• Check hinges: They should not be loose or have excessive wear on knuckles.
• Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by increasing the depth of the pocket for the bolt. • Check for misalignment of bolt and/or strike which may be preventing bolt from properly entering the strike. With the door open, extend and retract the bolt; if it is smooth, check the strike alignment.
• Bolt and strike are misaligned, see above. • Check the backset of door relative to adjustments already made to bolt.
• Verify proper door preparation and re-bore holes that are too small or misaligned.
• Verify bolt is installed with correct side up (Step 1)
Suggested Action
Cycle lock in both the locked and unlocked positions. If problems are found:
DefinitionsAutomatic Re-lock Time: After a successful code entry and the unit unlocks, it will automatically re-lock after thirty (30) seconds.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and can be enabled or disabled in the August Home App.
Low Battery: Battery state is shown on smartphone app.
Privacy Mode: Privacy mode is disabled by default. Privacy mode is enabled/disabled in the August Home App.
Shutdown Time: If the wrong code is entered five (5) times, the keypad will flash for 60 seconds. The lock will not allow operation for 60 seconds.
Volume Setting Mode: The volume setting is set to Low by default; otherwise it can be set to High or Silent in the August Home App.
56
Programming Troubleshooting
SymptomLock does not respond
- door is open and accessible.
Lock does not respond - door is locked and
inaccessible.
Unit is on for a while then shows no reaction.
Unit Chimes when unlocking with smartphone app, but the door will not
open.
Unit operates to allow access, but will not
automatically re-lock
• Check batteries are installed and oriented correctly (polarity) in the battery case.
• Check batteries are in good condition; replace batteries* if discharged.
NOTE TO INSTALLER AND CONSUMER
While EMTEK has included several features to prevent lockout (low battery warnings), it is still possible for a lockout situation to occur. Because this product has a mechanical override
(a key), EMTEK recommends you carry your keys with you to prevent lockout.
• Batteries may be completely discharged.
• Use your physical key to unlock the door.
• Batteries do not have enough power. Replace batteries*.
• Check door gaps for any foreign objects between door and frame.
• Check to see if Auto Re-lock Mode is enabled.
• Disable Auto Re-lock Mode to lock the door (automatically).• If low battery indicator is indicated in the August Home App (see below), change batteries*.
Suggested Action
* When batteries are replaced. Network Module locks have a real time clock that will be set through the User Interface (UI); it is recommended to verify correct date and time particularly those locks operation under Daylight Saving Time (DST).
57
Resetting Lock to Factory Default
When lock is reset to factory defaults, all programming features are reset to original default settings (see below).
1. Remove battery cover and batteries.2. Remove the interior escutcheon to access the reset button.3. The reset button (see image) is located beside the PCB cable connector.4. While pressing the reset button (Minimum of 3 seconds) reinstall batteries. Release reset button.5. Replace battery cover.
Factory Settings
SettingsAutomatic Re-lock
Inside Indicator Light
Volume Setting
Lockout Mode
Automatic Re-lock Time
Factory SettingsDisabled
Disabled (Off)
Enabled (Low)
Disabled
30 Seconds
58
FCC INTERFERENCE STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful Interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
INDUSTRY CANADA COMPLIANT This device complies with RSS·210 of the Industry Canada Rules Operation Is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement: This equipment compiles with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
INDUSTRIE CANADA CONFORME Ce dispositif est conforme à la norme CNR-210 d’industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu. y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôle. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Compliance
REV 19A 11-08-19
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Copyright © 2019, EMTEK Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of EMTEK Products, Inc. is prohibited.
!