EM3531B-WWVB Manual -TX05 A 说明书 front size:296*420mm … · station. If there are...
Transcript of EM3531B-WWVB Manual -TX05 A 说明书 front size:296*420mm … · station. If there are...
PT3531B-WWVB Manual
Features: WWVB Radio control time function
Perpetual Calendar Up to Year 2099
Time in optional 12/24 hour format.
Two daily alarms
Automatic snooze function
Temperature:
— Indoor temperature measurement ranges: 14°F (-9.9°C) ~ 122°F (50°C)
—Outdoor temperature measurement ranges: -40°F (-40°C) ~ 158°F (70°C)
— Temperature alternatively in °F or °C.
Minimum/maximum display for temperature
Wireless Remote Sensor:
— Wall Mount or Table Stand
— One Wireless Thermo Sensor Included
— 433.92MHz RF transmitting frequency
— 200 feet transmission range in an open area
The weather forecasting function
Colorful backlight function
USB charger function
Power Supply:
Weather Station:
Battery: 2 x LR03 AAA (not included)
DC-POWER: DC5V 1.2A
Wireless Remote Sensor:
Battery:2 x LR03 AAA (not included)
F.Y.I.:Alkaline zinc manganese battery can work at -20°C to +60°C,Polymer lithium ion rechargeable battery can
work at -40°C to +70°C, Please use different battery specifications according to the ambient temperature limit
PT3531B-WWVB Manual
Weather Station Appearance
Part A-Positive LCDA1: Weather Forecasting
A2: Time
A3: Week
A4: Indoor Temperature
A5: Outdoor Temperature
A6: Calendar
A7: Projection display: time and indoor or outdoor temperature
Part B – Back button and power
B1: “ ” touch field
B2: “MODE” button
B3: “MEM” button
B4: “+” button
B5: “-” button
B6: “LOOP” button
B7: “RAINBOW” button
B8: Alarm1 on/off shift switch
B9: Alarm2 on/off shift switch
B10: USB charger output socket
B11: Battery compartment
B12: Power supply socket
B13: Projection on/off shift switch
PT3531B-WWVB Manual
Part C –Wireless Remote Sensor: C1: Battery compartment
Initial operation: Open Weather Station battery compartment cover
Insert 2 x AAA batteries observing polarity [ “+” and “ –“ marks]
When you insert the batteries, all the icon on the LCD display will briefly light up for 3 seconds, and you will hear a
beep tone, and detect indoor temperature.
The Weather Station will now start to make a connection to the remote sensor. This operation takes about 3 minutes
and is displayed by a flashing reception RF antenna symbol in the “OUT” display area on the receiver.
This now, replace Wireless Remote Sensor battery compartment cover ,Open Weather Station battery compartment
cover ,Insert 2 x AAA batteries observing polarity [ “+” and “–“ marks]
After receiver has created a connection to the remote sensor, it will then enter the Radio control time receive mode.
Reception of the Radio signal: The clock automatically starts the WWVB signal search after 7 minutes of any restart or changing of new fresh
batteries. The radio mast icon starts to flash.
At 1:00 am /2:00 am / 3:00 am, the clock automatically carries out the synchronization procedure with the WWVBsignal to correct any deviations to the exact time. If this synchronization attempt is unsuccessful (the radio mast icon
disappears from the display), the system will automatically attempt another synchronization at the next full one hour.
This procedure is repeated automatically up to total 5 times.
To start manual WWVB signal reception, press "+" and "-" button at the same time. If no signals received within 7
minutes, then the WWVB signal search stops (the radio mast icon disappears) and start again at the next full one hour.
During RC reception,to stop searching radio signal, press and hold the “-” button more than 2 seconds.
F.Y.I.: A flashing radio mast icon indicates that the WWVB signal reception has started
A continuously displayed radio mast icon indicates that the WWVB signal was received successfully
We recommend a minimum distance of 8 feet to all sources of interference, such as televisions or computer monitors
Radio reception is weaker in rooms with concrete walls (e.g.: in cellars) and in offices. In such extreme
circumstances, place the system close to the window.
The adapter is located as far as possible from the product is larger than 2.5 feet, so the receiving effect is better.
During the RC receive mode, only the “-” button function, other button operation have no function, If you want
to carry out other functions of operation, please press and hold the “-” button more than 2 seconds to exit the
RC receiving mode.
PT3531B-WWVB Manual
Manual time setting: Press once “MODE” button, can switch the display calendar or Alarm 1 time or Alarm2 time
Press and hold down the “MODE” button more than 2 seconds, the Year display 2016 starts to flash, Now use “+”
and “-” buttons to set the correct year.
Press “MODE” button to confirm your setting, the Month display starts to flash. Now use “+” and “-” buttons to set the
correct month.
Press “MODE” button to confirm your setting, the Date display starts to flash. Now use “+” and “-” buttons to set the
correct date.
Press “MODE” button to confirm your setting, the Month and Date icon display starts to flash. Now use “+” and “-”
buttons to set the date display on Month/Date or Date/Month.
Press “MODE” to confirm your setting, the Time zones start to flash, Now use “+” and “-” buttons set a correct time
zone (-8 PST-07 MST -06 CST and -5 EST).
Press “MODE” to confirm your setting, the DST icon to flash. Now use “+” and “-” buttons to set the DST in on or off.
Press “MODE” to confirm your setting, the 12/24 hour mode display starts to flash. Now use “+” and “-” buttons to set
the correct 12/24 hour mode.
Press “MODE” to confirm your setting, the Hour display starts to flash. Now use “+” and “-” buttons to set the correct
hour.
Press “MODE” to confirm your setting, the Minute displays starts to flash. Now use “+” and “-” buttons to set the
correct minute.
Press “MODE” button to confirm your setting, the temperature unit starts to flash. Now use “+” and “-” buttons to set
the temperature unit in °C or °F you need.
Press “MODE” button to confirm your setting, the weather forecast pattern display starts to flash. Now use “+” and “-”
buttons to select the current weather pattern.
Press “MODE” to confirm your setting and to end the setting procedures, enter the clock mode.
F.Y.I.: After 20 seconds without pressing any button, the clock switches automatically from Set Mode to Normal Time Mode.
America time zone:
EST: Eastern Standard Time -5
CST: Central Standard Time -6
MST: Mountain Standard Time -7
PST: Pacific Standard Time -8
The time zone must be set correctly according to the weather station area, or when the time signal is received, the
time will be incorrect
When the Daylight saving time system is not implemented in this area, please set DST to OFF
Setting the daily alarms: Press and hold down “MEM” button more than 2 seconds until Alarm 1 Time hour display of the Alarm 1 time starts to
flash. Use the “+” and “-” buttons to set the required hour.
Press “MEM” button to confirm your setting, The Minute display of the Alarm 1 time starts to flash. Use the “+” and “-”
buttons to set the required minute.
Press “MEM” button to confirm your setting, The hour display of the Alarm 2 time starts to flash. Use the “+” and “-”
buttons to set the required hour.
EM3531B-WWVB Manual -TX05_A 说明书front size:296*420mm back size:296*420mm
PT3531B-WWVB Manual Press “MEM” button to confirm your setting, The Minute display of the Alarm 2 time starts to flash. Use the “+” and “-”
buttons to set the required minute.
Press “MEM” button to confirm your setting and to end the setting procedure.
F.Y.I.: After 20 seconds without pressing any button the clock switches automatically from setting mode to Normal clock
mode.
The alarm for opening and closing The alarm 1 or alarm 2 shift switch is pushed in the “ON” position, LCD display the “ ” or “ ”icon, the alarm 1 or
alarm 2 function is open
Product back of the alarm shift switch is pushed in the “OFF” position, the “ ” or “ ”icon disappears, the alarm 1 or
alarm 2 function is close
F.Y.I.: The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the alarm will be
repeated automatically after 24 hours.
Rising alarm sound (crescendo, duration: 2 minutes) changes the volume 4 times whilst the alarm signal is heard.
If a snooze alarm in the process, another alarm alarm, automatically stop the first alarm snooze function.
Switching off the alarm signal Press any button except the “ ” button to stop the alarm signal. It is not necessary to reactivate the alarm. It
switches itself automatically to the alarm time which has already been set.
Snooze function: Touch the " " field or press the “ ” button the alarm signal sounds to get to SNOOZE mode. The alarm
signal sounds again after approx. 5 minutes.
Displaying temperature and temperature trend The current indoor temperature and the temperature trend (indoor) are shown in the LCD display.
After successfully connecting with the outdoor sensor, the weather station can display the outdoor temperature and
the temperature trend (outdoor)
You may see the following displays:
The temperature is rising.
The temperature is remaining constant.
The temperature is falling.
Wireless sensor transmission: When the Weather Station successfully receives signals from the wireless sensor, the temperature of the “Out” are
displayed on the “Out” column of the weather station.
The weather station can connect up to 3 channel wireless sensor registration, the use of multiple wireless sensor,
the wireless sensor channel cannot choose the same channel at the same time (a total of 1, 2, 3 channel can
choose,)
Press the “+” button can switch the display of different channels of outdoor temperature
PT3531B-WWVB Manual If the weather station failed to receive transmission from remote sensor (“- -”display on the LCD), press and hold “+”
button more than 2 seconds to receive transmission manually. the outdoor temperature will show an animation of the
RF antenna symbol,the weather station will re-receive the wireless signal of the outdoor sensor.
F.Y.I.: when the wireless sensor set up different channels, the weather station "OUT" also want to switch to the same
channel. When there is no wireless sensor signal transmission on the channel, "--" will be displayed in the channel
of the weather station
When the wireless sensor has no channel selection function, the sensor defaults to channel 1.
Maximum/Minimum Temperature To toggle indoor/ remote maximum, minimum temperature data, press the “MEM” button:
Once to show the maximum temperature values.
Twice to sow the minimum temperature values
Three times to return to the current temperature levels
F.Y.I.: If the temperature reading is below ranges, the LL.L will be displayed. If the temperature reading is above ranges,
the HH.H will be displayed.
Outdoor temperature frost alertWhen the temperature of outdoor is +30°F to + 37°F or –1°C to + 3°C, the frost alarm will be activated, the frost alert icon " " flashing.
Low battery:
If the “IN” column shows the battery icon “ ”, you need to replace the weather station's battery as soon as possible,
if the “OUT” column is to display the battery icon “ ”, you need to replace the wireless sensor battery as soon as
possible.
The weather forecast: The weather station calculates a weather forecast for about the next 12 hours based on the barometric pressure
trend. Of course this forecast can‘t compare to that of professional weather services supported by satellites and high
performance computers, but merely provides an approximate indication of current developments. Please take the
weather forecast from your local weather forecasting service into account as well as the forecast from your weather
station. If there are discrepancies between the information from your device and from the local weather forecasting
service, please take the advice of the latter as authoritative.
The weather station displays the following weather symbols:
sunnyslightly
cloudycloudy rainy Heavy rainy Snowy
PT3531B-WWVB Manual
The weather station can display the barometric pressure trend.
You may see the following displays:
The barometric pressure will rise.
The barometric pressure will remain constant.
The barometric pressure will fall.
Projection description The projection shift switch is pushed in the “ON” position, the projection display will light up.
The projection shift switch is pushed in the “OFF” position, the projection display will be closed
When using the battery power supply, Touch the “ ” field, the projection can display 15 seconds.
When using the power adapter, the projection display will always light up.
The effective distance of projection display is 1 meters to 3 meters. in the night, there is no light wall or ceiling, can
clearly display the contents of a projection.
The contents of the projection display are time and indoor or temperature composition, wherein the temperature will
be displayed every 5 seconds for indoor / outdoor, has been circulating
To change the projection display direction, please hold “-” button for 3 seconds.
Background lighting When using the battery power supply, Touch the “ ” field, the backlight illuminates for 15 seconds.
When the power supply of the product is inserted into the power supply adapter, the battery will automatically
disconnect the power supply, and the backlight will always be bright. Press the “-” button to adjust the brightness of
the backlight, you can adjust the 4 state: 3 different brightness backlight and close the backlight. Users can choose
according to the personal preferences of different brightness backlight or turn off the backlight. Turn off backlight
when you can touch the “ ” field to light the backlight 15 seconds
When using the power adapter, press “LOOP” button 1 times, the backlight will automatically change color, you can
see more than 70 color cycle changes. Use the “LOOP” button to control the discoloration of the backlight on or off
the backlight
When using the power adapter, Press and hold the “LOOP” button for more than 2 seconds, backlight color will be
quickly changed, when the release of “LOOP” button will stop the color change, you can use this function to select
your favorite backlight color.
When the backlight light, you can press the "RAINBOW" button to select the backlight color, a total of 8 colors can be
selected
F.Y.I.: If using the power adapter, During RC reception, in order to prevent the interference of electric wave, the backlight
will be automatically closed.
The 8 backlight colors are: white, red, orange, yellow, green, cyan, blue, purple. When using the old battery, when
the power supply is not enough, there will be color difference, it is recommended to use the power adapter as far as
possible.
USB charger
PT3531B-WWVB Manual Products behind the USB socket, as a DC charging power supply, to provide handheld mobile devices
charging