Electricity (physics) class 10th
-
Upload
tushar-jain -
Category
Education
-
view
146 -
download
10
Transcript of Electricity (physics) class 10th
![Page 1: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/1.jpg)
Made By
Tushar jain
![Page 2: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/2.jpg)
ELECTRICITY
![Page 3: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/3.jpg)
Electricity has an important place in modern society. It is controllable and convenient form of energy for a variety of uses in homes, schools, hospitals, industries and so on. Now first, we will start from electric current and circuit.
INTRODUCTION
![Page 4: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/4.jpg)
Electric current : - It is a flow of electrons through a conductor. The device which causes the flow of electrons through a conductor is called a cell.Electrons flow from the negative terminal to the positive terminal. Electric current flow from positive terminal to the negative terminal.Electric current is expressed as : - The rate of flow of charges through a conductor or the quantity of the charges flowing through a conductor in unit time. I = Q / T (where I – current , Q – quantity of charge, T – time). The SI Unit of electric charge is coulomb (C). The SI Unit if current is called ampere (A). One ampere is the current flowing through a conductor if 1 coulomb of charge flows through it in 1 second.
Electric current
![Page 5: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/5.jpg)
Electric circuit : - It is a continuous and closed path of an electric current. In an electric circuit, the direction of electric current is taken as opposite to the direction of the flow of the electrons, which are negative charges.
Electric circuit
![Page 6: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/6.jpg)
Electric current will flow through a conductor only if there is a difference in the electric potential between the two ends of the conductor. This difference in electric potential between the two ends of a conductor is called potential difference.The potential difference in a circuit is provided by a cell or a battery. The chemical reaction in the cell produces a potential difference between the two terminals and sets the electrons in motion and produces electric current
Electric potential and potential difference
![Page 7: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/7.jpg)
Potential Difference : - Potential difference between two points A and B of a conductor is the amount of work done to move a unit charge from A to B.Potential Difference = Work done / Charge or V = W / QThe SI Unit of potential difference is volt (V). One volt is the potential difference when 1 joule of work is done to move a charge of 1 coulomb from one point to another.1 volt = 1 joule / 1 coulomb or 1 V = 1 J / 1 CPotential Difference is measured by a voltmeter. It is always connected in parallel across the two points between which the potential difference is to be measured.
![Page 8: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/8.jpg)
We know that an electric circuit comprises a cell or a battery, a plug key, electrical component(s), and connecting wire. It is often convenient to draw a schematic diagram in which different components of a circuit are represented by a symbol conventionally used. Conventional symbols used to represent some of the most commonly used electrical components are given in a table in next slide.
Circuit diagram
![Page 9: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/9.jpg)
Circuit diagram
![Page 10: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/10.jpg)
Ohm’s Law is a relationship between the potential difference across a conductor and the current flowing through it.Statement of Ohm’s Law At a constant temperature, the current flowing through a conductor is directly proportional to the potential difference between its ends.
Ohm’s law
![Page 11: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/11.jpg)
If I = current flowing thorough a conductor V = potential differenceThen, according to the Ohm’s Law V α I ( At constant temperature ) V = R x I ( R = Constant ) R is a conductor called resistance of conductor V / I = R Potential Difference / Current = Constant
Derivation of ohm’s law
![Page 12: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/12.jpg)
The resistance of a conductor depends upon its : - Length Area of cross section Nature of its Material
Factors on which resistance of a conductor depends
![Page 13: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/13.jpg)
Resistance of uniform metallic conductor is directly proportional to it length (l) and inversely proportional to the area of cross – section (A). That is, R α l ( 1 ) and R α 1 / A ( 2 ) Combining equations 1 and 2, we get R α l / A or R α ρ x l / A where ρ (rho) is a constant of proportionality and is called the electrical resistivity of the material of the conductor. The metals and alloys have very low resistivity. They are good conductors of electricity. Insulators like rubber and glass have high resistivity. Both the resistance and resistivity of a material vary with temperature.
Explanation of factors on which resistance of a conductor depends
![Page 14: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/14.jpg)
When three resistors R1, R2 and R3 are connected in series across AB The current in all the resistors is the same. The total voltage (PD) across the resistors is equal to the sum
of the voltage across each resistor. V = V1 + V2 + V3 The equivalent resistance is the sum of the resistances of each
resistor. Rs = R1 + R2 + R3
resistors in series
![Page 15: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/15.jpg)
When three resistors R1, R2 and R3 are connected in parallel across AB, The voltage (PD) in all the resistors is the same. The total current in all the resistors is the sum of the current in
each resistor. I = I1 + I2 + I3 The reciprocal of the equivalent resistance is the sum of the
reciprocals of each resistance. 1 / Rp = 1/R1 + 1/R2 + R3
Resistors in parallel
![Page 16: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/16.jpg)
If a current I flows through a resistor of resistance R and t be the time for which a charge Q flows through it, then the work done to move the charge through potential difference V W = Q x V P = W / t = Q x V / t Q / t = I or P = V x Ior Heat energy supplied = P x t = V x I x tAccording to Ohm’s Law V = IRHeat produced H = I2Rt
Heating effect of electric current
![Page 17: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/17.jpg)
Electrical Energy It is the work done to maintain the flow of current in a conductor W = Q x V I = Q / t Q = I x t W = I x t x V V = IR W = I2Rt The unit of electrical energy is joule (J).
Electrical energy and electrical power
![Page 18: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/18.jpg)
Electrical Power It is the rate at which electric current is use. Power = Work done / Time P = W / t . .W = I x I x Rt = I x I x Rt / t Power = I x I x R R = V / I = I x I x V / I = I x V Power = I x VThe SI Unit of power is watt (W).One watt is the power when 1A of current flows across a potential difference of 1V.1000 W = 1kW 1kW = 1000 watt x 3600 seconds The commercial unit of power is watt hour (Wh) or kilo watt hour (kWh).One kWh is the power consumed when 1W of power is used in 1 hour.
![Page 19: Electricity (physics) class 10th](https://reader034.fdocuments.in/reader034/viewer/2022042423/587fe2541a28ab46228b4aa5/html5/thumbnails/19.jpg)
THANK YOU