Electric Wheelchair ID MOUV (875026) · 2020. 6. 30. · 2、Electronic Brake This electric...
Transcript of Electric Wheelchair ID MOUV (875026) · 2020. 6. 30. · 2、Electronic Brake This electric...
- 1 -
Electric Wheelchair
ID MOUV (875026)
- 2 -
Safety Guide
⚫ Be sure to read this Safety Guide carefully before use for proper use.
⚫ If you do not follow the instructions in the "Safety Attentions", the product may be
damaged, people may be injured, and even life may be involved.
⚫ If the patient or his family needs to directly operate the wheelchair, the family should
understand the use of the instructions and then use it. ⚫ Please do not let the child and the person who cannot understand the operation operate the
wheelchair.
⚫ Users are strictly prohibited from being transported by wheelchair in any form by any
means of transport.
⚫ The user is not allowed to modify the wheelchair without authorization, and the company
is not responsible for any accidents.
⚫ It is strictly forbidden for the user to stand on the pedals, otherwise the wheelchair will fall
over.
⚫ Please do not explore your body while walking, otherwise it will affect the stability of
driving.
Any one is important about safety, so be sure to follow it. * After reading the instruction manual, it should be kept in a safe place for future use.
Warning!
1、Electric wheelchairs are suitable for driving on more spacious indoors, garden paths and
roads with good road conditions around the home. Do not approach motor vehicles and deep
pit surfaces.When encountering obstacles in front, avoid driving around the road to prevent the
risk of wheelchair tilt.
2、It is not advisable to climb long slopes to avoid overloading the circuit and motor and
consuming too much power.
3、Do not use the inertia to drive the wheelchair up the steps, otherwise it will cause accident
or damage to the wheelchair.
4、The auxiliary wheel installed at the rear is used to prevent the wheelchair from tipping over
when the angle of the uphill is too large,can not be removed.
5、Unless otherwise specified, all wheelchair adjustments should be carried out without a ride.
6、Before using the wheelchair, please check if the armrests, handles, etc. are loose. If so,
please contact a professional technician.
7、Please do not change your posture when you lean back, otherwise the wheelchair will tip
over.
8、The wheelchair should not walk on the escalator, otherwise serious personal injury will
occur.
9、When the person in the wheelchair is to be transferred from the wheelchair to another place,
first keep the wheelchair in the nearest and best position, point the front wheel of the
wheelchair to the place where it needs to be transferred, and confirm that the wheelchair is in
the brake state.
10、 When transporting a wheelchair, please grasp the fixed connection part of the
- 3 -
wheelchair,not the active part, such as the footrest device.
11、When parking is required during driving, simply release the controller handle to reset, and
the electric wheelchair will automatically brake,electric wheelchair can automatically brake when
parking on the slope;for safety, it is recommended to drive to a flat parking and tighten the brakes.
12、Always check if the electrical connector is well connected, if the solid screw is loose,
adjust it in time.
13、The rated load of the wheelchair is 100kg. The user weighs more than 100kg. Please
contact the manufacturer for special order.
14、When the wheelchair is driving on a sloping ground:the user must fasten the seat
belt;When going downhill, if the slope is greater than 5 degrees, the assistant put the
wheelchair back and move forward with careful confirmation;If you are facing forward
when going downhill, it may cause the user to lean forward and fall.
15、During the use of the patient, routine cleaning once a day, when replacing infected
patients,must be thoroughly disinfected with disinfectant.
** The product has a normal service life of 5 years from the date of delivery.
Do not turn off the power when going uphill and downhill,
otherwise it will cause a slope back!
Content
I、<< OVERVIEW >> ............................................................. ERREUR ! SIGNET NON DEFINI.
II、APPLICATION SCOPE ........................................................................................................... - 4 -
III 、 PRODUCT PERFORMANCE, SAFETY FEATURE, MAIN STRUCTURE &
COMPOSITION………………………………………………- 4 -
(I)MAIN STRUCTURE & PARAMETER ............................................................................. - 4 -
(II)FUNCTION OVERVIEW ................................................................................................. - 5 -
(III)WHEELCHAIR OPERATION ......................................................................................... - 5 -
IV、USING INTRODUCTION & ATTENTIONS ........................................................................ - 8 -
V、PRODUCT MAINTENANCE ....................................................................................................... - 8 -
VI、INTERPRETATION OF GRAPHICS,SYMBOLS,ABBREVIATIONS,ETC. USED IN MEDICAL DEVICE
LABEL…………………………………- 10 -
VII、ERROR CODE DESCRIPTION ......................................................................................... - 10 -
VIII、 CIRCUIT DIAGRAM .................................................................................................... - 11 -
IX、WARRANTY
CARD………………………………………………………………………………………- 10 -
- 4 -
1
X、CONTENT………………………………………………………………………… ………- 10 -
I、Overview
This user manual is applicable to electric wheelchairs, including various types of safety precautions,
function descriptions, and maintenance information.
The graphics in this manual are for user's reference only. Please refer to the actual product
for actual use.
II、Application Scope
This product is used for the elderly walking, disabled people and other groups with weak walking
ability (except for those who cannot judge the exercise environment). It is especially suitable for
short-distance walks in indoor, courtyard, sidewalk and other environments. The ideal travel tool for
the elderly and disabled.
III、Product Brief Introduction
(I)Product Parameter, Part Name
This product consists of frame, I-shaped, front wheel, rear wheel of hub motor, remote control,
battery box, control box, auxiliary wheel, seat back pad, foot pedal, etc., The structure diagram
is shown in the following figure:
1. Motor: DC24V 250W 2PCS
2. Batter capacity: DC24V 6AH 1PCS 10AH 1PCS
3. Charger: AC110-240V 50-60Hz Maximum output current: 2A
4. Controller: Maximum output current: 50A Normal operating current: 2-3A
Performance Parameter:
1. Maximum speed: ≤6KM/H Braking performance:≤1.5m
2. Static stability:≥9° Dynamic stability:≥6°
3. Minimum radius of gyration:≤1200mm
4. Theoretical travel distance:15KM / 20KM
Name Overall Length Overall Width Overall Height Seat Width Front Wheel
Dia.
Rear Wheel
Dia.
Parameter 930MM 580MM 970MM 420MM 6” 8”
Name Seat Height Seat Depth Backrest Height Folding Width N.W. Weight
Capacity
Parameter 530MM 360MM 400MM 340MM 18kg 100kg
- 5 -
3
14 15
* The graphics in this manual are for user's reference only. Please refer to the actual product for
actual use.
(II)Function Overview
The wheelchair is designed for both safety and convenience. Its main features are:
1、Foldable aluminum alloy frame;
2、The overall structure is simple and novel & lightweight;
3、Flip up footplate;
4、Electric /Manual with one-button switching;
5、Brushless motor;
6、wireless remote control;
(III)Wheelchair Operation
1. Open the wheelchair: Holding the backrest with one hand and holding the front frame to open it
at the same time (Pic 1, Pic 2) till the four-wheel landing and then pressing the bracket to hook the
folding switch iron to the rear frame bushing, the wheelchair is opened.
1.front fame
2. back frame
3. backrest frame
4. armrest
5. footplate
6. brake
7. 6” front castor
8. 8” motor rearwheel
9. controller
10. battery box
11.Auxiliary castor
12. seat cushion
13. back rest
14. handle bar
15. handle
16.safe belt
8
12
6
7
2
5
10
11
9
1
13
4
14
15
16
- 6 -
(1) (2) (3)
2. Wheelchair folding: first turn the footplates and armrests up, then pull the folding switch frame
and press down the backrest (Pic 4, 5). The wheelchair can be easily folded.
(3) (4)
3. Handle operation: release the handle of the quick release lever to adjust the height of the handle
or remove the handle, the lock will be fixed (Pic 6, 7, 8)
(6) (7) (8)
4. Remote control adjustment operation: Release the quick release lever handle to adjust or remove
the remote controller. Locked will be fixed (Pic 9, 10, 11)
- 7 -
9 10 11
5. Auxiliary wheel mounting: Install the auxiliary wheel and fixed it with a pin. (Pic 12, 13)
(12) (13)
6. Controller Installation:The controller is installed on the right by default (if you need to adjust the
installation position, you need to remove the fixing screws of the fixing bracket first, and then
change to the left to install). Insert the control wire connector on the controller and the
corresponding connector on the control box and tighten the connecting nut (Pic 3-1).
3-1
When connecting the joints, pay attention to the matching of the slots. The black arrows on the left
and right connectors should be corresponding. Do not force the insertion to prevent damage to the
connector (Pic 3-2).
- 8 -
3-2
IV、Using Introduction
1、Electric Wheelchair Operation
(1)After the operator is seated, turn on the power switch of the controller, and after the
prompt is given, the wheelchair is turned on,The LCD shows the current power and remaining
mileage. The system sets the safe start strategy. Please release the joystick when starting up.
Otherwise, the system will be faulty and cannot be turned on;
(2)The speed of the wheelchair is adjusted by the speed adjustment button on the controller. There
are five grades. It is better to use low speed when starting,Real-time speed can be displayed while
driving, and the grade cannot be changed while driving; The first time users recommend driving at a
low speed to avoid accidents due to unskilled operation.
(3)Pull the handle to start slowly, the joystick handle forwards the wheelchair forward,The
joystick handle turns left to the left wheelchair, the joystick handle turns right to the right
wheelchair, and to backwards the wheelchair retreats. After the simple understand, the wheelchair
can be driven freely;
(4)If you need a whistle alarm, press the button marked with the horn symbol on the controller;
(5)The battery is fully charged and displays 5 grids. When the battery is low, the grid is zero or
the battery icon is blinking.It is recommended that when the remaining battery power is insufficient,
please charge it in time to keep the battery fully charged;
(6)Press the power switch for a long time, and turn off the wheelchair after a prompt.
2、Controller Function Description
●Joystick: figure 1 as above, joystick can control the direction and speed of the wheelchair;
●Power Switch: figure 5 as above, when turned on, the power is turned on after the “drop” sounds;
1- Joystick
2-Speed limited reduction
3- Speed limited plus
4- Grade
5- Power switch
6- Speaker
7- Power capacity
1
2 3
4 5 6
7
- 9 -
when press power button for 3 seconds to turned off, and the "drop'sounds , the power is turned off
successfully;
●Speed limited grade:Speed limit reduction (Part 2 of the above figure), lowering the maximum
speed limit when pressed;The speed limit added (Part 3 of the above figure), and the maximum
speed limit is increased when pressed.
●Speaker: as figure 6 above,the horn sounds when pressed, and it does not ring if loose;
2、Electronic Brake
This electric wheelchair uses an advanced electronic brake system to stop if let go,do not turn off
the power when going uphill and downhill conditions. If you want stop or get off the wheelchair,
first pull the brakes to ensure that the brakes can be turned off by the two rear wheels to prevent the
wheelchair from slipping automatically. Follow this operation to ensure safe use. Users are advised
to turn off the controller without using a wheelchair to reduce power consumption.
3、Low Battery Smart Brake
(1)Wheelchair with electric and manual 2 driving modes.When it is turned on, the electric
mode is automatically activated;it is the manual mode when it is off.When the user stops, please
tighten the left and right rear brakes.
(2)During the trip, if the power is less than 10%, (part 7 of above figure) ,please charge in
time. It is recommended to tighten the rear wheel brake or turn on the manual mode to seek help
from the caregiver.
(3)In the case of uneven roads, it is also recommended to use the manual mode, which is
boosted by the caregiver to ensure safety.
4、Charging
(1)You must use the special charger provided with your electric wheelchair to ensure safe use.
Plug the charger's charging output plug into the charging socket on the back of the controller;
(2)The charger power plug is plugged into a voltage and frequency matching power supply;
(3)When the charging indicator on the charger turns green, it indicates that the power is
sufficient,(The battery capacity is 6Ah, the charging time depends on the amount of remaining
power in the original battery, and the uncharged new battery is filled for about 4-5 hours for the first
time),unplug the charger and the charging output plug when sufficient.
(4)Charging method:Insert charging head of the charger into the charging port on the bottom of
the remote control, as shown in the figure.
Charging port start of charge
Attention:Causes of minor injuries and moderate injuries
- 10 -
When you want to get up from a wheelchair, When getting on and off the wheelchair,
please do not stand on the footplate directly, attention to fix the rear wheel brake first,
to avoid overturning. prevent the rear wheel from sliding,and then lift
the footplate to ensure safety.
V、Product Maintenance
1. Preventive Examination
⚫ Be sure to check the following items before using, so that the wheelchair is always kept in a
safe state.
⚫ When you need repair, please inform the after-sales service department in time.
a) Attention: Check the screws on the universal wheel, drive wheel, brake and other parts. If
it is loose, please lock it.
b) Do not place the wheelchair in a place that is easily exposed to water.
⚫ Regularly check the screws security.
2. Cleaning,Maintenance& Mantenance Period
Wipe the body with clean water after use every day, and wipe it with a diluted cleaning solution.
Can't be wiped with a detergent such as alcohol!
a) Lubricants should be used to maintain wheelchairs every month.
b) Wash the seat cushion, back cushion & armrest regularly with warm water and diluted soapy
water.
VI、Interpretation of Graphics, Symbols, Abbreviations, etc. Used in Medical Device Label
- 11 -
Afraid of the rainFragile,handle with care, UPAttention,read the random file, No rollover
IXP3
Type B application part Classification of the protection degree of the liquid
2、Product storage and transportation conditions and methods
STORED IN A WELL-VENTILATED ROOM, THE AMBIENT TEMPERATURE IS -10 ° C ~ 45 ° C, THE
RELATIVE HUMIDITY IS NOT MORE THAN 93%, NO HARMFUL GASES, FLAMMABLE, EXPLOSIVE
SUBSTANCES AND CORROSIVE GASES ARE ALLOWED.
SUITABLE FOR ROAD, RAIL, AIR AND WATER TRANSPORT, DURING THE LOADING AND UNLOADING
AND TRANSPORTATION PROCESS, IT SHOULD BE PREVENTED FROM VIOLENT VIBRATION AND IMPACT,
AND SHOULD NOT BE DAMP. IT SHOULD NOT BE MIXED OR MIXED WITH FLAMMABLE AND
CORROSIVE SUBSTANCES.
VII、Precautions for use
1. Always install and commission the wheelchair before using. If you have any questions, please
consult an authorized agent or an authorized service provider.
2. To avoid potential dangerous such as rollovers, users must practice on a flat, wide field to
familiarize with the various operations and features first.
3. When getting on and off the wheelchair, make sure the wheelchair controller is off.
4. With the help of others, experience the effect of changes in the center of gravity of the wheelchair
on the progress, such as uphill and downhill or turn over the obstacle.
5. The driving characteristics of electric wheelchairs can be disturbed by electromagnetic fields
generated by mobile phones or other radiation devices. Therefore, when using the controller, the
peripheral communication tool should be turned off.
6. Electric wheelchairs using temperature range is -10° to +45°
7. Electric wheelchairs are not suitable for driving on very slippery surfaces (such as ice) and very
rough roads (such as gravel, gravel).
8. Electric wheelchairs cannot be used in the presence of a mixture of flammable anesthetic gas
and air or nitrous oxide.
9. Please do not interchange the left and right motor connectors. To avoid to cause an incorrect
connection. (Please follow the instructions)
VIII、Circuit Diagram
- 12 -
IX、Product Warranty Card
Product Warranty Card
This product is warranted as follows if it is not damaged
by humans and is used in strict accordance with the
instructions.
I.Frame/Body
Warranty for three years from the day of purchase .
II.Battery
Warranty for one year from the day of purchase .
III.Motor
Warranty for one year from the day of purchase .
IV.Controller
Warranty for one year from the day of purchase .
V.Charger
Warranty for one year from the day of purchase .
Product Name:
Model Specification:
Product Serial Number:
Production batch:
Date of Purchase:Month Day Year
Dealer:
- 13 -
X.其他内容
Others
Registrant &Manufacturer Name:Guangdong Dayang Medical Technology Co., Ltd.
Registrant's Domicile, Manufacturer's Domicile &Production Address:Xingxian Development
Zone,Changhongling Industrial Park(2nd Phase),Shishan,Nanhai District,Foshan,Guangdong,China
TEL:0757-81821201FAX:0757-81821200
Medical Device Registration Certificate Number:
Product Technical Requirement Number:
Medical Device Production License Number:
Production Date, Production Lot Number / Serial Number:Details in Nameplate
Service Life: 5Years