EIPH2 EIPH3 EIPH6nortonhydraulics.com/!data/products/ee_eiph2_3_6_engl.pdf · 2017. 10. 10. ·...
Transcript of EIPH2 EIPH3 EIPH6nortonhydraulics.com/!data/products/ee_eiph2_3_6_engl.pdf · 2017. 10. 10. ·...
EIPH2EIPH3EIPH6INTERNAL GEARPUMPS
• new Generation IPHnew technology
• up to 400 bar
• industrial version
• cast iron housing
• noise-optimized
• multi-flow-pumps with common suction port
Photo: Trumpf
Internal gear pump Type EIPH2 high pressure pumpwith constant displacement volume
Technical Data:
Rated Size NG 004 005 006 008 011 013 016 019 022 025Spec. volume Vth [cm3/rev.]*** 3.8 5.4 6.4 7.9 10.9 13.3 15.8 19.3 22.2 25.2
Continuous operating pressure [bar]** 330 300 250 250
Peak operating pressure[bar]max.10sec.15%dutycycle** 350 300 280
Cut-in pressure peak [bar]** 400 325 300
Max. speed [rpm] 4,200 4,000 3,600
Nominal speed [rpm] 400 – 4,000 400 – 3,600 400 – 3,000
Operating viscosity [mm2/s] 10 – 300
Starting viscosity [mm2/s] 2,000
Operating medium HL – HLP DIN 51 524 part 1/2
Max. medium temperature [°C] 80
Min. medium temperature [°C] -20
Max. ambient temperature [°C] 80
Min. ambient temperature [°C] -20
Max. admission pressure (intake side) [bar] 2 bar absolute
Min. admission pressure (intake side) [bar] 0.8 bar absolute (Start 0.6)
Weight appr. [kg] 4.9 4.9 5.0 5.2 5.4 5.5 5.7 6.1 6.3 6.5
Degree of filtration Class 20/18/15 due to ISO 4406
Efficiency ηvol 90 91 92 93 93 94 95 95 95 95
Efficiency ηhm 88 90 90 91 92 92 93 93 93 93
Pump noise* (measured in sound chamber) dB[A] 53 54 55 57 58 59 60 61 62 63
n = 1.450 p = 250 bar T = 50 °C Medium: HLP 46
*Measured in anechoic room of Eckerle Hydraulic Division; Axial microphone distance 1.0 m
** For acceptable pressure at 400-1.800 rpm. Further rpm on request. *** Due to manufacturing tolerances the displacement volume could vary.
Characteristics
• Internal gear pump with axial and radial gap compensation
• Radial compensation with segments
• Suction and pressure port radial
• Field of application: Industrial hydraulic
• Low noise
• Long time life
• Low pulsation (pressure pulsation ~ 2%)
• Multi flow combinations
2
EIPH2
Technical Data:
Rated Size NG 014 016 020 025 032 040 050 064
Spec. volume Vth [cm3/rev.]*** 14.6 16.0 20.0 24.8 32.1 40.1 50.3 64.6
Continuous operating pressure [bar]** 330 250
Peak operating pressure[bar]max.10sec.15%dutycycle** 350 300 280
Cut-in pressure peak [bar]** 400 325 300
Max. speed [rpm] 4,000 3,000 2,500 1,800
Nominal speed [rpm] 400 – 3,600 400 – 2,800 400 – 2,200 400–1,800
Operating viscosity [mm2/s] 10 – 300
Starting viscosity [mm2/s] 2,000
Operating medium HL – HLP DIN 51 524 part 1/2
Max. medium temperature [°C] 80
Min. medium temperature [°C] -20
Max. ambient temperature [°C] 80
Min. ambient temperature [°C] -20
Max. admission pressure (intake side) [bar] 2 bar absolute
Min. admission pressure (intake side) [bar] 0.8 bar absolute (Start 0.6)
Weight appr. [kg] 13.1 13.2 13.4 13.5 13.7 16.4 17.5 19.5
Degree of filtration Class 20/18/15 due to ISO 4406
Efficiency ηvol 91 92 93 93 94 95 95 95
Efficiency ηhm 90 90 91 92 92 93 93 93
Pump noise* (measured in sound chamber) dB[A] 60 61 62 63 64 65 66 66
n = 1.450 p = 250 bar T = 50 °C Medium: HLP 46
*Measured in anechoic room of Eckerle Hydraulic Division; Axial microphone distance 1.0 m
** For acceptable pressure at 400-1.800 rpm. Further rpm on request. *** Due to manufacturing tolerances the displacement volume could vary.
Internal gear pump Type EIPH3 high pressure pumpwith constant displacement volume
3
EIPH3
Characteristics
The new series EIPH were developed particularly for the high requirements of industrialhydraulics. Their favourable noise characteristic, extremely low delivery and pressurepulsation, outstanding efficiency within broad revolution and viscosity ranges, have firmlyestablished gap-compensated high pressure internal gear pumps among high pressurepumps. Simple combinability to multiple pumps with separate or common inlet is given.
The EIPH is a consistent advancement that already for over 40 years in the industry usedgap-compensated internal gear pump technology, System Eckerle.
Internal gear pump Type EIPH6 high pressure pumpwith constant displacement volume
4
EIPH6
Technical Data:
Rated Size NG 040 050 064 080 100 125 160 200 250Spec. volume Vth [cm3/rev.]*** 40.8 50.6 65.3 80.0 101.2 125.7 160.1 200.9 249.9
Continuous operating pressure [bar]** 330 315 300 280 250 210
Peak operating pressure [bar] max. 10sec 15% dutycycle** 340 330 330 300 270 250
Cut-in pressure peak [bar]** 350 340 340 320 300 250
Max. speed [rpm] 2.400 2.200 2.000
Nominal speed [rpm] 400 – 2,200 400 – 2,000 400 – 1,800
Operating viscosity [mm2/s] 10 – 300
Starting viscosity [mm2/s] 2.000
Operating medium HL – HLP DIN 51 524
Max. medium temperature [°C] 80
Min. medium temperatur [°C] -20
Max. ambient temperature [°C] 80
Min. ambient temperature [°C] -20
Max. admission pressure (intake side) [bar] 2 bar absolute
Min. admission pressure (intake side) [bar] 0,8 bar absolute
Weight appr. [kg]: 23 25 28 31 36 41.5 49 58 69
Degree of filtration Class 20/18/15 due to ISO 4406
Efficiency ηvol 96 96 96 95 95 94 94 93 93
Efficiency ηhm 89 90 91
Pump noise* 72 73 74 75 76 76 77 77 78 (measured in sound chamber) dB[A]
n = 1.450 p = 250 bar T = 50 °C Medium: HLP 46
*Measured in anechoic room of Eckerle Hydraulic Division; Axial microphone distance 1.0 m
** For acceptable pressure at 400-1,800 rpm. Further rpm on request. *** Due to manufacturing tolerances the displacement volume could vary.
Double Pump with SAE-A-2-hole flange and cylindrical shaft Order example: EIPH2- _ _ _RK00-1X+EIPH2- _ _ _RP30-1X
Dimensions
Pump with SAE-A-2-hole flange and cylindrical shaft Order example: EIPH2- _ _ _RK03-1X
EIPH2
5
NG A F G H L M N 0004 71 50 54 57 38,1 17,5 14 M8x15
005 71 50 54 57 38,1 17,5 14 M8x15
006 73 50 54 57 47,5 22 19 M10x16
008 76 50 54 57 47,5 22 19 M10x16
011 82 50 54 57 52,4 26,2 25 M10x17
013 87 50 54 57 52,4 26,2 25 M10x17
016 92 50 54 57 52,4 26,2 25 M10x17
019 99 55 59 62 52,4 26,2 25 M10x17
022 105 55 59 62 52,4 26,2 25 M10x17
025 111 55 59 62 52,4 26,2 25 M10x17
shaft end
direction of rotation
suction port
NG A F G H004 71 50 54 57
005 71 50 54 57
006 73 50 54 57
008 76 50 54 57
011 82 50 54 57
013 87 50 54 57
016 92 50 54 57
019 99 55 59 62
022 105 55 59 62
025 111 55 59 62 Pressure connections see single pumps
shaft end
Common suction port pump size NG 004-016
direction of rotation
pump size NG 019-025
NG A B C D E F G H K L M N O014 90,4 38,1 17,5 M8x15 14 64 65 67 57 52,4 26,2 25 M10x17
016 92,4 38,1 17,5 M8x15 14 64 65 67 57 52,4 26,2 25 M10x17
020 97,9 47,5 22 M10x17 18 64 65 67 57 58,7 30,2 32 M10x17
025 104,4 47,5 22 M10x17 18 64 65 67 57 58,7 30,2 32 M10x17
032 114,4 47,5 22 M10x17 18 64 65 67 57 58,7 30,2 32 M10x17
040 125,4 52,4 26,2 M10x17 20 70 73 79 63 58,7 30,2 32 M10x20
050 139,4 52,4 26,2 M10x17 20 70 73 79 63 58,7 30,2 32 M10x20
Pressure connections see single pumps
direction of rotation
suction port
shaft end
shaft end
direction of rotation
NG A F G H K014 90,4 64 65 67 57
016 92,4 64 65 67 57
020 97,9 64 65 67 57
025 104,4 64 65 67 57
032 114,4 64 65 67 57
040 125,4 70 73 79 63
050 139,4 70 73 79 63
Common suction port pump size NG 014-032 pump size NG 040-050
Dimensions
Double Pump with SAE-B-2-hole flange and cylindrical shaft Order example: EIPH3- _ _ _RK20-1X+EIPH3- _ _ _RP30-1X
Pump with SAE-B-2-hole flange and cylindrical shaft Order example: EIPH3- _ _ _RK23-1X
6
EIPH3
Dimensions
7
EIPH3/2
Double Pump with SAE-B-2-hole flange and cylindrical shaft Order example: EIPH3- _ _ _RK20-1X+EIPH2- _ _ _RP30-1X
EIPH3 EIPH2
Pressure connections see single pumps
shaft end
direction of rotation
suction port
NG A F G H K014 90,4 64 65 67 57
016 92,4 64 65 67 57
020 97,9 64 65 67 57
025 104,4 64 65 67 57
032 114,4 64 65 67 57
040 125,4 70 73 79 63
050 139,4 70 73 79 63
NG AA FF GG HH004 71 50 54 57
005 71 50 54 57
006 73 50 54 57
008 76 50 54 57
011 82 50 54 57
013 87 50 54 57
016 92 50 54 57
019 99 55 59 62
022 105 55 59 62
025 111 55 59 62
Pressure connections see single pumps
direction of rotation
suction port
shaft end
direction of rotation
Common suction port
shaft end
NG A B C D E L M N O040 123 57,2* 27,8* M12x22 20 69,9 35,7 35 M12x25
050 129 57,2* 27,8* M12x22 20 69,9 35,7 40 M12x25
064 138 57,2* 27,8* M12x22 20 69,9 35,7 40 M12x25
080 147 66,7* 31,8* M14x25 30 77,8 42,9 50 M12x25
100 160 66,7* 31,8* M14x25 30 77,8 42,9 50 M12x25
125 175 66,7* 31,8* M14x25 30 77,8 42,9 50 M12x25
160 220 66,7* 31,8* M14x25 30 88,9 50,8 65 M12x25
200 245 66,7* 31,8* M14x25 38 88,9 50,8 70 M12x25
250 275 66,7* 31,8* M14x25 38 106,3 62 70 M16x25 * Pressure port: SAE 518C, high pressure series (code 62)
NG A040 123
050 129
064 138
080 147
100 160
125 175
160 220
200 245
250 275
8
Dimension EIPH6
Pump with SAE-D-2-hole flange and cylindrical shaft Order example: EIPH6- _ _ _RK23-1X
Double Pump with SAE-D-2-hole flange and cylindrical shaft Order example: EIPH6- _ _ _RK20-1X+EIPH6- _ _ _RP30-1X+
Pressure connections see single pumps
EIPH6 EIPH2
NG AA FF GG HH004 71 50 54 57
005 71 50 54 57
006 73 50 54 57
008 76 50 54 57
011 82 50 54 57
013 87 50 54 57
016 92 50 54 57
019 99 55 59 62
022 105 55 59 62
025 111 55 59 62
NG A L M N O040 123 69,9 35,7 35 M12x25
050 129 69,9 35,7 40 M12x25
064 138 69,9 35,7 40 M12x25
080 147 77,8 42,9 50 M12x25
100 160 77,8 42,9 50 M12x25
125 175 77,8 42,9 50 M12x25
160 220 88,9 50,8 65 M12x25
200 245 88,9 50,8 70 M12x25
250 275 106,3 62 70 M16x25
direction of rotation
Common suction port
shaft end
direction of rotation
Common suction port
shaft end
9
Dimension EIPH6
Double Pump with SAE-D-2-hole flange and cylindrical shaft Order example: EIPH6- _ _ _RK23-1X+EIPH2- _ _ _RP30-1X+
Double Pump with SAE-D-2-hole flange and cylindrical shaft Order example: EIPH6- _ _ _RK20-1X+EIPH3- _ _ _RP30-1X+
Pressure connections see single pumps
EIPH6NG A040 123
050 129
064 138
080 147
100 160
125 175
160 220
200 245
250 275
NG AA FF GG HH KK014 90,4 64 65 67 57
016 92,4 64 65 67 57
020 97,9 64 65 67 57
025 104,4 64 65 67 57
032 114,4 64 65 67 57
040 125,4 70 73 79 63
050 139,4 70 73 79 63
EIPH3
Connecting flanges SAE EIPH
10
SAE pipe threaded flange
SAE flange metric tapped Version a
Version b
Nr. Article number Type Pmax AD A B C D E F G1 G2 H I L
1a 07 07 04 0030 AD15-SAE12M22x1,5 315 15 M22x1.5 12 38.1 54 17.48 46 52 60 13 7 9
1b 07 07 04 0026 EFG1/2-SAE12 350 G1/2" 13 38.1 54 17.48 46 36 19 19 9
2a 07 07 04 0031 AD22-SAE34M30x2 160 22 M30x2 19 47.63 65 22.23 50 60 69 14 7.5 11.5
2b 07 07 04 0027 EFG3/4-SAE34 350 G3/3" 19 47.63 65 22.23 50 36 18 19 11
3a 07 07 04 0032 AD28-SAE100M36x2 160 28 M36x2 24 52.37 70 26.19 55 63 72 16 7.5 11.5
3b 07 07 04 0028 EFG1-SAE100 315 G1" 25 52.37 70 26.19 55 38 18 22 11
4a 07 07 04 0033 AD35-SAE114M45x2 160 35 M45x2 29 58.72 79 30.18 68 65 76 14 10.5 11,5
4b 07 07 04 0029 EFG1 1/4-SAE114 250 G1 1/4" 32 58.72 79 30.18 68 41 21 22 11.5
5a 07 07 04 0037 AD42-SAE112M52x2 160 42 M52x2 36 69.85 94 35.71 78 70 82 16 11 13.5
5b 07 07 04 0034 EFG1 1/2-SAE112 200 G1 1/2" 38 69.85 94 35.71 78 45 25 24 13.5
6b 07 07 04 0036 EFG2-SAE200 200 G2" 51 77.77 102 42.88 90 45 25 30 13.5
7b 07 07 04 0041 EFG2 1/2-SAE212 160 G2 1/2" 63 88,9 114 50.8 105 50 25 30 13.5
8a 07 07 04 0042 AD30-SAE100M42x2HD 400 30 M42x2 25 57.2 81 27.8 70 82 95 24 13.5 13
9a 07 07 04 0043 AD38-SAE114M52x2HD 400 38 M52x2 32 79.38 113 36.5 95 96 111 30 16 17.5
Connecting flanges SAE EIPH
11
SAE Pressure- and Suction flange SAE J518C, ISO 6162
Suction flange for Intermediate housing
Inlet Nr. Version
Type a b
EIPH2/2 - NG016 1'' 3 • •
EIPH2/2 ab NG0191 1/4'' 4 • •
EIPH3/3 bis NG0321 1/2'' 5 • •
EIPH3/3 ab NG040 2'' 6 •
EIPH6/6
EIPH6/3
EIPH6/2
• = available = on request
Inlet Nr. Version Outlet Nr. Version
Type a b a b
EIPH2-004-005 1/2'' 1 • • 1/2'' 1 • •
EIPH2-006-008 3/4'' 2 • • 1/2'' 1 • •
EIPH2-011-025 1'' 3 • • 1/2'' 1 • •
EIPH3-014-016 1'' 3 • • 1/2'' 1 • •
EIPH3-020-032 1 1/4'' 4 • • 3/4'' 2 • •
EIPH3-040-064 1 1/4'' 4 • • 1'' 3 • •
EIPH6-040-064 1 1/2'' 5 • • 1'' * 8 •
EIPH6-080-125 2'' 6 • 1 1/4'' * 9 •
EIPH6-160 2 1/2'' 7 • 1 1/4'' * 9 •
*High pressure range
Order example
EIPH2 - 016 RK03 - 1XHigh pressure pump overall size 2 with 15,8 cm3/Uclockwise rotationcylindrical shaft with coneSAE/B-2-hole flange connection SAE flange connectionrevision code 1X
Ordering Code
EIP H2-016 RK03-10 S123Special version number (not applicable with standard pumps or when the
type key is unambiguous)
Revision code 1st number: Change of mounting dimensions2nd number: Change of pump with same mounting dimensions
Sense of rotation R: ClockwiseL: Anticlockwise
Overall size 2 or 3 or 6
Shaft end K: Cylindrical with coneP: Cone tooth system on both sides
Rated size, three digits
Type H: High pressure pump
Eckerle internal gear pump
Fastening flange 0: SAE/A 2-hole flange, centre-Ø 82.552: SAE/B 2-hole flange, centre-Ø 101.62: SAE/D 2-hole flange, centre-Ø 152.4 at EIPH 6 3: Direkt fixture5: VDMA on demand– other flanges on request –
cone is standard; (cone = add-on facility for additional pumps to create multiple-flow pumps)
Intake and delivery connection 3: SAE-flange connections – other flanges on request –0: suction port closed; common inlet
EIPH
All indicated data serve alone the product description and are not as characteristics in the legal sense to be understood. Subject to alterations. 0202
0101
83/Ü
&P/0
110
Eckerle Industrie-Elektronik GmbH · P.O. box 1368Otto-Eckerle-Str. 6/12A · D-76316 MalschPhone: +49 (0) 72 46/92 04-0 · Fax: +49 (0) 72 46/92 [email protected] · www.eckerle.com