Eec 115 Practical- Electrical Engineering
-
Upload
viethungcao -
Category
Documents
-
view
461 -
download
208
Transcript of Eec 115 Practical- Electrical Engineering
1
UNESCO-NIGERIA TECHNICAL &
VOCATIONAL EDUCATION
REVITALISATION PROJECT-PHASE II
+_
I
Low High
+_
V
Low High
10 Ohms10 Ohms
100 voltsR
YEAR I- SEMESTER I
PRACTICAL
Version 1: December 2008
NATIONAL DIPLOMA IN
ELECTRICAL ENGINEERING TECHNOLOGY
ELECTRICAL ENGINEERING
SCIENCE (I)
COURSE CODE: EEC 115
TABLE OF CONTENTS
WEEK 1: Basic Electrical quantities measurement
WEEK 2: Measurement of voltage and current
WEEK 3: Measurement of resistance
WEEK 4: Ohm’s law
WEEK 5: Series circuit connections
WEEK 6: Parallel circuit connections
WEEK 7: Resistance in parallel
WEEK 8: Capacitor in circuit
WEEK 9: Voltage division principle
WEEK 10: Series-parallel connected resistors
WEEK 11: Kirchhoff’s current law
WEEK 12: Kirchhoff’s voltage law
WEEK 13: Resistivity
WEEK 14: Power in d.c. circuit
WEEK 15: Charging and discharging of a capacitor
Basic Electrical Quantities Measurement Week 1
1
TITLE:- Basic Electrical Quantities Measurement
It is necessary knowing how to measure voltage, current, and resistance. Special
types of instruments are used to measure these basic electrical quantities. The instrument
used to measure voltages is a voltmeter, the instrument used to measure current is a
ammeter, and the instrument used to measure resistance is a ohmmeter.
Commonly, all three instruments are combined into a single instrument such as a
multimeter or AVO meter ( Ampere- Volt-Ohmmeter), in which you can choose what
specific quantity to measure by selecting the switch setting.
Figure (1) shows typical portable multimeters, part (a) from figure shows analog
multimeter with pointer, and part (b) shows a digital multimeter with digital screen.
(a) Analog multimeter (b) Digital multimeter Figure (1) Typical portable Multimeter
General scheme symbols is used to indicate placement of meters in circuit when value
changes need to be shown. Figure (2) shows meter symbols used to present the different
meters, as voltmeter, ammeter and ohmmeter.
Basic Electrical Quantities Measurement Week 1
2
A
+ _
Ω
+ _
V
+ _
0.00
+ _A
0.00
+ _V
0.00
+ _Ω
(c) Ohmmeter
(b) Ammeter
(a) Voltmeter
Figure (2) Meter symbols
How to use Analogue meter:
Figure (3) shows a typical multimeter. This device can measures the three electric
quantities. The following step shows how to obtain readings from a multimeter.
1.Set the range of the desired quantity to be measured to the highest value.
2.Connect the leads to the right terminals at the meter
3.Switch on the circuit if necessary.
4.Adjust the range until you get clear readings.
5.Apply the following formula to obtain the measured quantity.
ScaleFull
Rangeading
Re
For example, referring to figure (3),the reading was 3.5 from a full-scale value of 5V, as
shown in the small box.The range was set to X300V.So the measured voltage is
Basic Electrical Quantities Measurement Week 1
3
2105
3005.3
600
300
60
12
3
0.06
1.2
12
120
x1
x10
x1k
X100k
x100
600
300
60
12
0.3
AC VOLT
OHMS
DC VOLT
DC Current
1
2
3
4
5
10
20
50
0
Ω
Scale
Range
Pointer Reading =3.5
Off
0
50
100200
500
1k
5k
20k
30
40
6 8 1012
14
15
0
2
40 VAC
ADC
VDC
3
4
ΩA VCommon
Figure(3): Multimeter
Note:
The scale has to be viewed from an angle perpendicular to it.
Measurement of Voltage and Current Week 2
4
TITLE: Measuring the Voltage
Voltage can be considered as the pressure that force the electrons to flow. The voltage
is being measured by measuring the difference between the voltages at the two terminals of
the device-under-test which is the (voltage drop). This can be performed using a measuring
instrument called voltmeter.
The voltmeter connection in the circuit is a parallel connection.
Figure (1) illustrates how to connect voltmeter in the circuit to measure the voltage
across the resistor.
I R
+ _
I R
+ _V
+
_
V
0.00
+ _V
Figure (1) Example of a voltmeter connection
Procedure
1. Adjust the range of the meter
2. Connect the leads in the true terminals of the meter
3. Apply the other ends of the leads to the resistor under test
4. Record the reading and apply the formula scalefull
Rangeading
Re
Measurement of Voltage and Current Week 2
5
Measuring Current with Ammeter
It is well known that current in the circuit is measured by ammeter, to measure the
current , the circuit must be open and the ammeter is connected in series the circuit.
Procedure
1. Connect the simple circuit shown in the figure below
2. Open the circuit between the source and the resistor
3. Connect the ammeter terminals to one end of the resistor and to the source
4. Switch on the power supply and record the reading.
5. Apply the formula scalefull
Rangeading
Re if necessary
Note:
If the meter did not give any movement or tried to move backward, then switch the terminal
leads with each other
Measurement of Voltage and Current Week 2
6
Figure(1) illustrates how to connect ammeter in the circuit and measure the current.
0.00
+ _A
I
A+ _
R
+ _R
+ _
R
+ _
I
I R
+ _V
R
+ _V
R
+ _V
I
(a) Circuit in which the current is to be measured.
(b) Open the circuit between the resistor and the positive terminal
of battery.
(c) Install the ammeter in the current pass with polarity as shown
(negative to negative, positive to positive)
Figure 1: Example of an ammeter connection
Measurement of Resistance Week 3
7
TITLE:- Measuring Resistance with Ohmmeter
To measure resistance, connect the ohmmeter across the resistor. The resistor must first
remove from the circuit. This procedure is shown in figure (2).
R
+ _
R
+ _V
+
_
Ω
0.00
+ _Ω
Figure (2) Example of using ohmmeter
Procedure
1. Adjust the meter so that when the two terminals are short circuited, the ohmmeter reads
zero
2. Disconnect the resistor to be measured from the circuit (why?)
3. Apply the meter leads to the resistor terminals (resistor is parallel to the meter)
4. Record the reading and apply the formula scalefull
Rangeading
Re if necessary
Ohm’s Law Week 4
8
TITLE: Ohm's law
OBJECTIVE:- Verification of Ohm’s Law
Ohm’s law is the most important mathematical relationship between voltage, current
and resistance in electricity.
It is important to know how to read the resistors' colour code and hence its ohmic value. In
the following figure it shows a table of the meaning of each colour. For example, for the
resistor in the figure(1),the value of the resistor is 200kΩ,since the band 1 is red i.e.
equivalent to 2 in the table ,band 2 is black equivalent to zero in the table and the band 3 is
yellow indicating of a multiplier of 10,000.see at the bottom of the figure.
The fourth band is the tolerance band i.e the percentage of error. It usually comes in
two colors ,the silver indicates ±5% and the gold indicates ±10%.so for example, the value
resistor will lie between 210kΩ and 190kΩ.
Procedure
1. Select a number of different resistors
2. Use the table below to determine their values
3. Use ohmmeter to measure the same resistors you figured out
4. Compare your calculated values with the readings you obtained
V = I X R
Ohm’s Law Week 4
9
Resistors color code:
Band 1:Figure 1Band2:Figure 2
Multiplier Tolerance
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
First figure
value
0
1
2
3
4
5
6
7
8
9
X1
X10
X100
X1000
X10,000
X100,000
X1,000,000
X10,000,000
X100,000,000
X1,000,000,000
Second
figure value
0
1
2
3
4
5
6
7
8
9
Colour Multiplier
2 0 X10,000=200K %5
Figure 1:Resistors colour code
Series Circuit Connection Week
10
TITLE:- series circuit
OBJECTIVE: verification of series circuit
There are three basic types of circuits, series, parallel and series-parallel circuits.
Series circuit:
Series circuit is the simplest circuit. The conductors, loads and power supply are connected with
only one path for the current. The same amount of current will flow through each load. However,
the voltage across each load will be different. Figure(1) shows different configuration of series
circuits.
Procedure:
1. Connect a number of resistors is series
2. Measure the current in the circuit. What do you notice?
3. Connect two identical lamps in series. Notice the brightness of the lamps
4. Add one more lamp to the circuit you connected in step 3. What do you notice?
5. Repeat step 4 with more lamps and measure the current in all cases
6. Write a conclusion
Series Circuit Connection Week
11
The Electric Current
A B
A B
Figure1 : Different configuration of series circuits
Parallel Circuit Connections Week 6
12
TITLE: Parallel circuit:
OBJECTIVE: To verify parallel circuit
The main difference between a series circuit and a parallel circuit is in the way the
components are connected. Parallel circuit should have at least two loads connected
separately to the voltage source, so the voltage across the loads are the same. However, in a
parallel circuit the electric current has several paths that it can travel. Figure(2) shows
different configuration of parallel circuits.
Procedure
1. Connect a number of resistors is parallel as shown below
2. Measure the current in each branch and the total current. Comment on the
readings
3. Add more resistors in parallel. Repeat step 2
4. Measure the voltage across each resistor. Comment on your results
A
B
BA
Parallel Circuit Connections Week 6
13
A
B
+
_
A
B
+
_
IT
IT
I1
I2 I1 I2
IT
IT
A
B
+
_
IT
IT
I1
I2
Figure1: Differe
Resistance in Parallel Week 7
14
TITLE:- Resistance of parallel connected resistors
OBJECTIVE: To verify parallel connection circuits
1. To measure the total resistance of combinations of parallel connected resistors.
A parallel circuit is a circuit with more than one path for current flow. Removing one
branch of a parallel circuit does not affect the operation of (the current in) the remaining
branch circuit. The total resistance of parallel connected resistors is less than the
resistance of smallest branch resistor. There are many parallel circuits in electronic
equipment. The formula for calculating RT for parallel resistors is:
1/RT = 1/R1 + 1/R2 + 1/R3 +……..+ 1/Rn
RT = R1xR2xR3 / R1R2+R2R3+R3R1
Materials Required:
Multi-meter.
Resistors: all ½ watt, 330 Ω, 470 Ω, and two 1200 Ω.
Procedure:
1) Refer to the following figure choose the resistors shown as combination A.
Resistance in Parallel Week 7
15
2) Measure the resistance of each of the resistors supplied for combination A. Record
the measured value of each resistor in the column beneath is colour coded value in the
following table.
3) Measure the RT of the parallel combination and record your reading in the column
label “Measured RT “in the following table.
Parallel
Combination
Colour
coded
value
R1
330 Ω
R1
470 Ω
R1
1200 Ω
R1
1200 Ω
Measured
RT
Ω
Group A Measured
value, Ω X X
Group B Measured
value, Ω X
Group C Measured
value, Ω X X
Questions:
Q1) was the value RT greater or smaller than the value of the smallest branch resistor in each
combination?
Q2) Combination (group C) placed two resistors of equal value in parallel. From the results
of measuring RT of this combination of resistors, suggest a general rule for RT of any two
resistors of equal value connected in parallel.
Ohmmeter
Resistance in Parallel Week 7
16
Q3) what is the RT of three 330 Ω resistors in parallel?
Variable Resistors.
Objective:
To measure resistance between the variable (centre terminal) and the terminals on
other side of it as the shaft of a potentiometer is turned from its minimum to maximum
position.
Materials Required:
1) Multi-meter.
2) Variable Resistor 10000 Ω Potentiometer.
Procedure:
1. Examine the potentiometer assigned to you. Place it so that the shaft points toward
you. Measure and record in the following table the value of potentiometer between
the two outside terminals.
2. Turn the shaft to any position (1) and measure the resistance between the left terminal
(A) and the centre terminal (C) Record this reading in the following table .
3. Without moving the shaft, measure the resistance between the right terminal (B) and
the centre terminal (C), Record this reading RBC in the table.
4. Complete the table.
Resistance in Parallel Week 7
17
Table 6.1
Step Potentiometer
shaft setting
RAB
Ω
RAC
Ω
RBC
Ω RAC + RBC
1 Any X X X
2 Position 1 X
3 Position 2 X
4 C.W X
5 C.C.W X
Questions:
Q1) In the potentiometer above, what is the relation between RAC, RBC, and RAB? Do your
measurements confirm this relation?.
Q2) In what position of the shaft is the resistance between A and B minimum?.
Q3) In what position of the shaft is the resistance between.
A
B
C
Capacitor Week 8
18
TITLE: Capacitor in a circuit
OBJECTIVE: To test capacitor by observing their charging and discharging using an ohmmeter.
Capacitor is a device that stores energy in the electric field created between a pair of conductors
on which equal but opposite electric charges have been placed. Capacitance is a measure of a
capacitor's ability to store charge. A large capacitance means that more charge can be stored.
Capacitance is measured in farads, symbol (F). However 1F is very large, so prefixes are used to
show the smaller values.
Three prefixes (multipliers) are used, µ (micro), n (nano) and p (pico):
µ means 10-6
(millionth), so 1000000µF = 1F
n means 10-9
(thousand-millionth), so 1000nF = 1µF
p means 10-12
(million-millionth), so 1000pF = 1nF
Materials Required: Ohmmeter.
Capacitor.
Fig 8.1
Capacitor Week 8
19
Procedure:
1. Connect the circuit as shown above.
2. Read the ohmmeter and record the conditions of the capacitor which are:
a. If the ohmmeter reading move toward zero and then slowly returns to infinity
means the capacitor is in a good condition.
b. If the ohmmeter move towards zero and remain at zero means the capacitor is
short circuited .
c. If the reading doesn’t change and remains at infinity means the capacitor is open
circuited.
3. Replace the capacitor and repeat step 1 and 2.
4. Repeat step 3 until all capacitors are tested.
Table 8.1
Answer the
following
questions:
Q1) What
is the
meaning of
capacitanc
e?
Q2) Draw
the symbol
Capacitor
Reading Remark
C1
C2
C3
Capacitor Week 8
20
of a capacitor?
Q3) State 1 application for capacitors?
Q4) complete the following:
If the ohmmeter reading move toward zero and then slowly returns to infinity means
………………………
the ohmmeter move towards zero and remain at zero means
…………………………
If the reading doesn’t change and remains at infinity means
…………
Voltage Division Principle Week 9
21
TITLE: Voltage divider
OBJECTIVE: Verify the operation of voltage divider
APPARATUS:
(1) 2 Digital multimeters
(2) Variable power supply
(3) Resistor R1 = 330
Resistor R2 = 1K
Resistor R3 = 500 - Trimmer
PROCEDURES:
(1) Connect a digital multimeter as d.c voltage, and another one as milliammeter fig 9.1
(2) Set the switch S1 to OFF
(3) Adjust the voltage to 5V by turning the variable power supply
(4) Read the value of the voltage V0 (no load) between point 3 and earth and write it
down in table 9.1
(5) Calculate the value of the voltage V0 (no load) and write it in table 9.1
(6) turn the trimmer R3 completely clockwise
(7) Set the switch S1 to ON
(8) Read the values of the voltage and of the current and write them in table 9.1
(9) Repeat the previous operation for all the values of R3 shown in table 9.1
(10) Represent in fig 9.2 the characteristic curve voltage-current of the voltage divider
(11) Comment on the results
Voltage Division Principle Week 9
22
Fig 9.1
Table 9.1: Obtained Results V0(no load [V]
Measured
V0(no load) [V]
calculated R3 [] 500 400 300 200 100 0
V0 [V]
I0[mA]
Fig 9.2
ON
com A V
ON
com A VS
1 2 3
R2
R1
R3
Voltmeter Milliammeter
S1
V0(V)
I0(mA)
Series-Parallel Connection of Resistors Week 10
23
TITLE: Series-Parallel Resistors
OBJECTIVES: Observe the behaviour of series-parallel connected resistors
APPARATUS: (1) Digital multimeter
(2) Resistor R1 = 1K 5%
Resistor R2 = 1K 5%
Resistor R3 = 220K 5%
PROCEDURE:
(1) Set the switches S1 and S2 to ON
(2) Connect a multimeter, set as ohmmeter, fig 10.1
(3) Write down in table 10.1 the value read in the ohmmeter
(4) Calculate the value of the resistance R12 and write down the value in table 10.1
(5) Compare the measured value with the calculated one
(6) Move a terminal of the ohmmeter from the jack 2 to the jack 1
(7) Set the switches S1 to ON, and S2 to OFF
(8) Write down in table 10.1 the value read in the ohmmeter
(9) Calculate value of the resistance R13 and write down the value in table 10.1
(10) Compare the measured value with the calculated one
(11) Set the switches S1 and S2 to ON
(12) Write down in table 10.1 the value read in the ohmmeter
(13) Calculate the value of the resistance Re and write down the value in table 10.1
(14) Comment on the measured value with calculated one
Series-Parallel Connection of Resistors Week 10
24
Fig 10.1
Table 10.1: Obtained Results R12 []
Measured
R12 []
calculated
R13 []
Measured
R13 []
Calculated
Re []
Measured
Re []
Calculated
V
ON
com
1 2 R3
R1 R2
S2 S1
Kirchhoff’s Laws Week 11
25
TITLE:- Kirchhoff’s Current |Law
OBJECTIVE: To verify Kirchhoff’s law
APPARATUS:
(1) Variable power supply
(2) Voltmeter
(3) Milliameter
(4) Resistor R1 = 1K 5%
Resistor R2 = 1K 5%
Resistor R3 = 220K 5%
PROCEDURES:-
(1) Connect multimeter, set as a d.c voltmeter, and another one as milliameter, Fig 11.1
(2) Adjust the voltage to 10V by turning the variable power supply
(3) Set the switches S1 to On, S2 and S3 to OFF.
(4) Write down in table 11.1 the values read on the voltmeter and on the
milliammeter.
(5) Set the switches S2 to ON, and S1 and S2 to OFF
(6) Write down in table 11.1 the values read on the voltmeter and on the
Milliammeter
(7) Set the switches S3 to ON, S1 and S2 to OFF
(8) Write down in table 11.1 the values read on the voltmeter and on the milliammeter
(9) Calculate the value of the current in the single resistors and write down the results in
table 11.1
(10) Compare the calculated values with the measured ones.
(11) Verify that the sum of the current that go in the node 2 is equal to the sum of the
current that go out.
(12) Comment on the result in steps (10) and (11)
Kirchhoff’s Laws Week 11
26
Fig 11.1
Fig 11.1
Table 11.1: Obtained Results
VR1
[V]
I1
[mA]
VR2
[V]
I2
[mA]
VR3
[V]
I3
[mA]
I1
[mA]
I2
[mA]
I3
[mA]
I = 0
Measured Value Calculated value
V
ON
com
ON
com
Millammeter Voltmeter
1 2 2 2
S1 S2 S3
R2 R3 R1
A
Kirchhoff’s Laws Week 12
29
TITLE:- Kirchhoff’s Voltage Law
OBJECTIVE:- To verify Kirchhoff’s Voltage law
APPARATUS:
(1) Variable power supply
(2) Voltmeter X 2
(3) Resistor R1 = 100 5%
Resistor R2 = 220 5%
Resistor R3 = 330 5%
PROCEDURE:
(1) Use two Multimeters, set as dc voltmeters and connect them as it is shown in figure
12.1
(2) Set the switches S1, S2 and S3 to ON
(3) Adjust the voltage to 10V by varying the variable power supply
(4) Write down in table 12.1 the values read on the voltmeters
(5) Move the terminal of the voltmeter 2 on the terminals of the resistance RL (Jacks 4
and 5), measure the voltage drop and write down the value in Table 12.1
(6) Move the terminals of the voltmeter 2 on the terminals of the resistance R3 (Jacks 6
and earth), measure the voltage drop and write down the value in table 12.1
(7) Verify that the sum of the voltage drops on the resistors corresponds to the voltage
VS.
(8) Calculate the value of the voltage drops on the resistors and write down the value in
table 12.1.
(9) Comment on the results in steps (7) and (8).
Kirchhoff’s Laws Week 12
30
Fig 12.1
Table 12.1: Obtained Results
Vs (v) VR1 (V) VR2 (V) VR3 (V) VR1 (V) VR2 (V) VR3 (V) V = VR1 + VR2 + VR3
(V)
Measured Measured value Calculated value Measured/Calculated
V
ON
com V
ON
com A A
Voltmeter 1 Voltmeter 2
1 2 3 4 S1 S2 R1
R2 R3
5 6 S3
VS
Resistivity Week 13
18
TITLE:- Resistivity of a material
OBJECTIVE:- To verify resistivity of a material
APPARTUS:- (1) A length of a given resistance wire
(2) Digital multimetre
(3) Metre rule
(4) Micrometer gauge
PROCEDURE:- (1) Measure the length of the given resistance wire
(2) Measure the diameter, d of the material by a micro meter gauge
(3) Compute the cross sectional area using the formula A = d2/4
(4) Set the digital multimetre to a suitable ohmmeter range and connect across the
resistance wire at various lengths as shown in fig 13.1 below
(5) S tart with a length of 10cm, 20cm, etc and tabulate the result in the form shown in
the table below.
(6) Plot a graph of RA (nm2) against L(cm) and find the slope of the graph.
(7) Comment on the results in step 6.
Table 13.1
L(cm) R() d(mm) A(nm2) RA(nm
2)
10
20
30
40
50
60
70
80
90
Resistivity Week 13
19
Fig 13.1
Fig 13.1
0 10 20 30 40 50 60 70 80 90
Resistance wire Multimeter
Probe
Meter
rule
Power in d.c. Circuit Week 14
31
TITLE:- Experimental determination of power in a d.c circuit
OBJECTIVE:- To determine the power in a d.c circuit.
BACKGROUND INFORMATION
The power of a resistor can be determined in a dc circuit under any of the following
conditions:
(1) if the resistance of the resistor is unknown, but the voltage (V) across the resistor and
current (I) through the resistor can be measured.
i.e Power P = IV, watts.
(2) if the resistance (R) if the resistor and the current through it are known to give,
P = I2R (watts).
(3) if the resistance (R) of the resistor and the voltage across it are known to give
P = V2/R (watts)
PROCEDURE:
(1) Connect the circuit shown in fig 14.1 with the voltmeter V across the resistor R and
the ammeter A in series with it.
(2) Use the ammeter to record the current, I (Ampere) through the resistor and the
voltmeter to record the P.d. (volts) across the resistor.
(3) Determine and record the value of R (in ohms) before the commencement of the
experiment.
Fig 14.1
Voltmeter
Ammeter
R
R
A
V
E
Power in d.c. Circuit Week 14
32
RESULT ANALYSIS:-
Calculate the power P, across the resistor using each and all the formulae stated above.
Charging and Discharging of a Capacitor Week 15
32
TITLE:- Charging and discharging current of a capacitor
OBJECTIVE:- To determine charging and discharging of a capacitor
APPARATUS:-
(1) Potentiometer
(2) Ammeter
(3) Power supply
PROCEDURE:
Capacitor charging
Suppose we have an initially uncharged capacitor C (i.e. having zero voltage across it) in
figure 15.1 and we begin to move the wiper of the potentiometer towards the upper end X.
As this happen the potential difference across the capacitor C gradually increase, and
consequently the amount of charge stored by the capacitor also increase according to the
expression,. Q = CV, in order words, as the slider of the potentiometer moves upwards X, so
the upper plate of C becomes more positively charged with respect to point X which is
earthed (i.e. at zero potential).
Fig 15.1
Capacitor discharge current
Let us refer to fig 15.1 and assume that the capacitor C has been fully charged to the
maximum voltage, E volts of the d.c supply. Once again we bear in mind that the slide of the
potentiometer must have point X for the potential difference across the capacitor to be E
volts. (the maximum value). Now, if the slide of the potentiometer is moved downwards
from X towards position Y (i.e. zero potential), then the capacitor begins to discharge current
from the upper plate of the capacitor (previously at a higher potential) through the ammeter
and the potentiometer to the position T. Under this condition, the current flows through the
ammeter in the opposite direction.
Potentiometer
dischargin
g current
(Capacitor
)
C + _
+
_
E X
Y
+ Upper movement.
Of slide
Vc