EE2254 MJ 2010

3
B.E./B.Tech. DEGREE EXAMINATION, APRIL/MAY 2010 Fourth Semester Electrical and Electronics Engineering EE2254 — LINEAR INTEGRATED CIRCUITS AND APPLICATIONS (Regulation 2008) (Common to Instrumentation and Control Engineering and Electronics and Instrumentation Engineering) Time: Three hours Maximum: 100 Marks Answer ALL Questions PART A — (10 × 2 = 20 Marks) 1. What is the purpose of oxidation process in IC fabrication? 2. What is parasitic capacitance? 3. List any four characteristics of an ideal OP-Amp. 4. Design an amplifier with a gain of –10 and input resistance of 10 k . 5. Define slew rate and state its significance. 6. An 8 bit DAC has a resolution of 20mV/bit. What is the analog output voltage for the digital input code 00010110 (the MSB is the left most bit)? 7. Draw the pin diagram of IC 555 timer. 8. Mention any two application of multiplier IC. 9. List the important parts of regulated power supply. 10. What are the advantages of switch mode power supplies? PART B — (5 × 16 = 80 Marks) 11. (a) Explain the basic processes used in silicon planar technology with neat diagram. Or (b) Discuss the various methods used for fabricating IC resistors and compare their performance. www.5starnotes.com www.5starnotes.com

description

ECE

Transcript of EE2254 MJ 2010

  • B.E./B.Tech. DEGREE EXAMINATION, APRIL/MAY 2010

    Fourth Semester

    Electrical and Electronics Engineering

    EE2254 LINEAR INTEGRATED CIRCUITS AND APPLICATIONS

    (Regulation 2008)

    (Common to Instrumentation and Control Engineering and Electronics and

    Instrumentation Engineering)

    Time: Three hours Maximum: 100 Marks

    Answer ALL Questions

    PART A (10 2 = 20 Marks)

    1. What is the purpose of oxidation process in IC fabrication?

    2. What is parasitic capacitance?

    3. List any four characteristics of an ideal OP-Amp.

    4. Design an amplifier with a gain of 10 and input resistance of 10 k .

    5. Define slew rate and state its significance.

    6. An 8 bit DAC has a resolution of 20mV/bit. What is the analog output voltage

    for the digital input code 00010110 (the MSB is the left most bit)?

    7. Draw the pin diagram of IC 555 timer.

    8. Mention any two application of multiplier IC.

    9. List the important parts of regulated power supply.

    10. What are the advantages of switch mode power supplies?

    PART B (5 16 = 80 Marks)

    11. (a) Explain the basic processes used in silicon planar technology with neat diagram.

    Or

    (b) Discuss the various methods used for fabricating IC resistors and compare their

    performance.

    www.5starnotes.com

    www.5starnotes.com

  • 12. (a) (i) Explain the functions of all the basic building blocks of an Op-Amp.(8)

    (ii) Explain the application of OPAMP as (1) integrator (2) differentiator. (8)

    Or

    (b) Find 0V of the following circuit.

    13. (a) Design and explain triangular wave generator using Schmitt trigger and integrator

    circuit.

    Or

    (b) (i) Explain the operation of dual slope ADC. (8)

    (ii) Explain the following characteristics of ADC resolution, accuracy, settling time, linearity.

    (8)

    14. (a) With neat block diagram, explain IC566 VCO operation and discuss any two

    applications.

    Or

    (b) What are the modes of operation of IC555? Derive the expression of time delay of a

    monostable multivibrator.

    15. (a) With a neat diagram, explain working principle of switch mode lower supply.

    Or

    (b) Write brief notes on:

    (i) IC MA 78 40

    (ii) Optocoupler.

    www.5starnotes.com

    www.5starnotes.com

  • www.5starnotes.com

    www.5starnotes.com