EDC Land Rig Technical Specification 2012-07-16
-
Upload
ahmed-serag -
Category
Documents
-
view
9 -
download
0
description
Transcript of EDC Land Rig Technical Specification 2012-07-16
-
Project: EDC Land RigPrepared by: Hamed Mosbah - Jotun Coatings
Cons/Eng: 1 Date: 7/16/2012Client: EDC Sub contr:
Technical specificationEDC Land Rigs
EPC:
Page 1 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
8.8 TU 24 h * 10 h * 4 h * 17 0
8.8 TU 24 h * 10 h * 4 h * 17 0
10 TU 10 h * 5 h * 2,5 h * 10 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible
35
26
HARDTOP AS, COLOUR
1 h
100 P
NR
P
P
230
JOTAMASTIC 80, GREY 80 90 113 P
4 h
Flash Point C
50 50
Dry spec. Wet spec. Brush Roller
JOTAMASTIC 80, RED 80 90 113 P
Surface Prep. Loose paint and heavy corrosion to be removed by scraping. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Corroded and damaged areas to be power-tool cleaned to St. 3 (ISO 8501-1:2007). Edges to intact paint system to be feathered.
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Substrate Mild steel Area No. 1
Location Date 7/1/2012
Position 2R ISO 12944-2 category N/A
Customer Approved by Version 1Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Application RestrictionRecommended Pot life
0 h
Nozzle Orifice Nozzle PressureMin C Max C
JOTAMASTIC 80, RED 150 bar 2 h 10 5010 min
Dry to touch 23 C
35
JOTAMASTIC 80, GREY 150 bar 2 h 10
.017" - .023"23 C
7A : 1B
Induction Time
Mixing Ratio
Volume
10 min 50
HARDTOP AS, COLOUR 150 bar 4 h 0 50
.017" - .023"
.013" - .018"
7A : 1B
4A : 1B
Product Application Methods
Spray
R
R
R
4 h
Product
Page 2 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10.6 FC 2 h * 1,5 h * 40 min * 17 0
5.3 FC 24 h * 10 h * 4 h * 17 0
10 FC 10 h * 5 h * 2,5 h * 10 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible
1/2 h
50
.013" - .018" 150 bar 4 h 1 h 50
4 h 35 10
HARDTOP AS, COLOUR
50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h
Max C10 min 25 5
Min CBARRIER 77, GREY .015" - .021" 150 bar 24 h
4A : 1B 26 00
P
P
250
HARDTOP AS, COLOUR
3A : 1B
10 min
P
Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C
50 50 100 P
JOTAMASTIC 80, GREY 80 150 188
Dry spec. Wet spec.
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Brush Roller
BARRIER 77, GREY 53 50 94 P NR
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Substrate Mild steel Area 1 No. 2
1Location Date 7/1/2012
Position 2B ISO 12944-2 category N/A
EDC Land Rig Prepared by Hamed Mosbah - Jotun CoatingsCustomer Approved by Version
7A : 1B
R
R
R
Product Recommended Pot life Dry to touch 23 C Induction Time
Mixing Ratio
Volume
Product Application Methods
Spray
Project
Page 3 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10 TU 24 h * 10 h * 4 h * 17 0
10 TU 24 h * 10 h * 4 h * 17 0
10 TU 24 h * 10 h * 4 h * 17 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible
50
150 bar 4 h 0 h 4A : 1B
4 h 35 10
HARDTOP AS, COLOUR .013" - .018"
50
150 bar 2 h 10 min 7A : 1B
Max C
150 bar 2 h 10 min 7A : 1B
Nozzle Orifice Nozzle Pressure
23 C
JOTAMASTIC 80, GREY .017" - .023"
Application Restriction
4 h 35 10
Recommended Dry to touch 23 C Flash Point C
Product Induction Time
Mixing Ratio
Volume
240
JOTAMASTIC 80,GREY
Pot life
Min C
JOTAMASTIC 80, RED .017" - .023"
80 80 100 P
NR
P
R
R
R P
JOTAMASTIC 80,GREY 80 80 100 P
Spray
JOTAMASTIC 80,RED 80 80 100 P
23C 40CDry spec. Wet spec. Brush Roller
Surface Prep. Loose paint and heavy corrosion to be removed by scraping. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Corroded and damaged areas to be power-tool cleaned to St. 3 (ISO 8501-1:2007). Edges to intact paint system to be feathered.
Type of coat Vol. solids % Filmthickness (m) Recoating intervals ThinnerProduct Application Methods10C
Substrate Mild steel Area 1 No. 3
1Location Date 7/1/2012
Position 3R ISO 12944-2 category N/A
Customer Approved by VersionProject EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
1 h 26 0 50
Page 4 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10.6 FC 2 h * 1,5 h * 40 min * 17 0
5.3 FC 24 h * 10 h * 4 h * 17 0
10 FC 10 h * 5 h * 2,5 h * 10 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible
Flash Point C
Application Restriction
Nozzle Orifice
Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C
250
HARDTOP AS, COLOUR
Product Recommended
P
P
R
R
R P50 50 100
JOTAMASTIC 80, GREY 80 150 188 P
Dry spec. Wet spec. Brush Roller
BARRIER 77, GREY 53 50 94 P NR
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Position 3B ISO 12944-2 category N/ASubstrate Mild steel Area 1 No. 4
Version 1Location Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Nozzle Pressure
23 CMin C Max C
BARRIER 77, GREY .015" - .021" 150 bar 24 h 1/2 h 3A : 1B 10 min 25 5 50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
HARDTOP AS, COLOUR .013" - .018" 150 bar 4 h 0 4A : 1B 1 h 26 0 50
Page 5 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 TU 2 h * 1,5 h * 1 h * 7 0
8.5 TU 4 h * 2 h * 1,5 h * 7 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible140
Product Recommended Application Restriction
Min C Max C
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
56 100 179 P
10C 23C 40CDry spec. Wet spec. Brush Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Welding seams and areas with damaged shopprimer to be power-tool cleaned to St. 3 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 4R ISO 12944-2 category N/ASubstrate Mild steel Area 1 No. 5
Location Date 7/1/2012Version 1Customer Approved by
Product Application Methods
Spray
Project EDC Land Rig Prepared by
Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C Nozzle Orifice Nozzle Pressure
23 C
Hamed Mosbah - Jotun Coatings
PILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 6 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 FC 2 h * 1,5 h * 1 h * 7 0
8.5 FC 4 h * 2 h * 1,5 h * 7 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible
R
R
140
Product Recommended Pot life
Wet spec. Brush
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY
Recoating intervals Thinner
56 100 179 P
10C 23C 40CDry spec.
Area 1
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m)
No. 6
Date 7/1/2012
Position 4B ISO 12944-2 category N/ASubstrate Mild steel
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by Version 1
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max C
Induction Time
Mixing Ratio
VolumePILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 7 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 TU 2 h * 1,5 h * 1 h * 7 0
8.5 TU 4 h * 2 h * 1,5 h * 7 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible140
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
56 100 179 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Welding seams and areas with damaged shopprimer to be power-tool cleaned to St. 3 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 5R ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 7
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 8 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 FC 2 h * 1,5 h * 1 h * 7 0
8.5 FC 4 h * 2 h * 1,5 h * 7 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible140
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
56 100 179 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 5B ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 8
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 9 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 TU 2 h * 1,5 h * 1 h * 7 0
8.5 TU 4 h * 2 h * 1,5 h * 7 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible140
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
56 100 179 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Welding seams and areas with damaged shopprimer to be power-tool cleaned to St. 3 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 6R ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 9
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 10 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 FC 2 h * 1,5 h * 1 h * 7 0
8.5 FC 4 h * 2 h * 1,5 h * 7 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible140
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
56 100 179 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 6B ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 10
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 11 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
8.8 TU 24 h * 10 h * 4 h * 17 0
8.8 TU 24 h * 10 h * 4 h * 17 0
10 TU 10 h * 5 h * 2,5 h * 10 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible
NR
P
230
HARDTOP AS, COLOUR 50 50 100 P
R
R
R P
Roller
JOTAMASTIC 80, GREY 80 90 113 P
Dry spec. Wet spec. Brush
JOTAMASTIC 80, RED 80 90 113 P
Surface Prep. Loose paint and heavy corrosion to be removed by scraping. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Corroded and damaged areas to be power-tool cleaned to St. 3 (ISO 8501-1:2007). Edges to intact paint system to be feathered.
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Position 7R ISO 12944-2 category N/ASubstrate Mild steel Area 1 No. 11
Version 1Location Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CJOTAMASTIC 80, RED .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
HARDTOP AS, COLOUR .013" - .018" 150 bar 4 h 0 h 4A : 1B 1 h 26 0 50
Page 12 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10.6 FC 2 h * 1,5 h * 40 min * 17 0
5.3 FC 24 h * 10 h * 4 h * 17 0
10 FC 10 h * 5 h * 2,5 h * 10 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible
PR
R
R
HARDTOP AS,COLOUR 50 50 100
94 P NR
P
P
JOTAMASTIC 80,GREY 80 150 188 P
BARRIER 77,GREY 53 50
23C 40CThinner
Dry spec. Wet spec. Brush Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervalsProduct Application Methods10C
Substrate Mild steel Area 1 No. 12
Spray
Location Date 7/1/2012
Position 7B ISO 12944-2 category N/A
Customer Approved by Version 1Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C
250
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CBARRIER 77,GREY .015" - .021" 150 bar 24 h 1/2 h 3A : 1B 10 min 25 5 50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
HARDTOP AS, COLOUR .013" - .018" 150 bar 4 h 0 4A : 1B 1 h 26 0 50
Page 13 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10 TU 24 h * 10 h * 4 h * 17 0
10 TU 24 h * 10 h * 4 h * 17 0
10 TU 24 h * 10 h * 4 h * 17 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible
JOTAMASTIC 80, GREY 80 80 100 P
Product
P
R
R
R P
240
JOTAMASTIC 80, RED 80 80 100 P
Dry spec. Wet spec. Brush Roller
JOTAMASTIC 80, GREY 80 80 100 P NR
Surface Prep. Loose paint and heavy corrosion to be removed by scraping. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Corroded and damaged areas to be power-tool cleaned to St. 3 (ISO 8501-1:2007). Edges to intact paint system to be feathered.
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Substrate Mild steel Area 1 No. 13
Version 1Location Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Position 8R ISO 12944-2 category N/A
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max C
Recommended Pot life Induction Time
Mixing Ratio
Volume
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
JOTAMASTIC 80, RED .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
Page 14 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
10.6 FC 2 h * 1,5 h * 40 min * 17 0
5.3 FC 24 h * 10 h * 4 h * 17 0
5.3 FC 24 h * 10 h * 4 h * 17 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible
Flash Point C
Application RestrictionNozzle Orifice
Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C
350
JOTAMASTIC 80, GREY
Product Recommended
80 150 188 P
NR
P
R
R
R P
JOTAMASTIC 80, RED 80 150 188 P
Dry spec. Wet spec. Brush Roller
BARRIER 77, GREY 53 50 94 P
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Position 8B ISO 12944-2 category N/ASubstrate Mild steel Area 1 No. 14
Version 1Location Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Nozzle Pressure23 C Min C Max C
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
JOTAMASTIC 80, RED .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
JOTAMASTIC 80, GREY .017" - .023" 150 bar 2 h 10 min 7A : 1B 4 h 35 10 50
Page 15 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
16 TU 5 h * 4 h * 3 h * 7 0
16 TU 5 h * 4 h * 3 h * 7 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible50
Product Recommended Application Restriction
Min C Max C
NR
SOLVALITT, ALUMINIUM 40 25 63 P P
SOLVALITT, ALUMINIUM R
R
40 25 63 P
10C 23C 40CDry spec. Wet spec. Brush Roller
Surface Prep. SSPC-SP11
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 9R ISO 12944-2 category N/ASubstrate Mild steel Area 1 No. 15
Location Date 7/1/2012Version 1Customer Approved by
Product Application Methods
Spray
Project EDC Land Rig Prepared by
Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C Nozzle Orifice Nozzle Pressure
23 C
Hamed Mosbah - Jotun Coatings
SOLVALITT, ALUMINIUM .015" - .021" 150 bar NA NA NA 30 min 26 5 50
SOLVALITT, ALUMINIUM .015" - .021" 150 bar NA NA NA 30 min 26 5 50
Page 16 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
11.2 TU 2 h * 1,5 h * 1 h * 7 0
11.2 TU 2 h * 1,5 h * 1 h * 7 0
9.6 TU 24 h * 16 h * 12 h * 2 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible140
PILOT II, COLOUR 48 40 83 P
NR
P
R
R
R P
PPILOT QD PRIMER, GREY 56 50 89
Dry spec. Wet spec. Brush Roller
PILOT QD PRIMER, RED 56 50 89 P
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Welding seams and areas with damaged shopprimer to be power-tool cleaned to St. 3 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner10C 23C 40C
Substrate Mild steel Area 1 No. 16
Location Date 7/1/2012
Position 10R ISO 12944-2 category N/A
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by Version 1
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max C
NA
PILOT QD PRIMER, RED .015" - .021" 150 bar NA NA NA
150 bar NA NA 5
15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA
NA 15 min 26 50
30 min 37 5 50
PILOT QD PRIMER, GREY .015" - .021"
Page 17 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 TU 2 h * 1,5 h * 1 h * 7 0
8.5 TU 4 h * 2 h * 1,5 h * 7 0
TU:Touch up R: Recommended NR: Not Recommended P:Possible
Mixing Ratio
Volume
R
140
Product Recommended Pot life Induction Time
Brush
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
N/A
Filmthickness (m) Recoating intervals Thinner
Substrate
56 100 179 P
10C
17
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. Welding seams and areas with damaged shopprimer to be power-tool cleaned to St. 3 (ISO 8501-1:2007).
Type of coat Vol. solids %23C 40C
Dry spec. Wet spec.
Position 11R ISO 12944-2 categoryMild steel Area 1 No.
Customer Approved by VersionLocation Date 7/1/2012
1Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 18 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.6 FC 2 h * 1,5 h * 1 h * 7 0
8.5 FC 4 h * 2 h * 1,5 h * 7 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible140
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
PIONER TC, COLOUR 34 40 118 P P
PILOT QD PRIMER, GREY R
R
P
10C 23C 40CDry spec. Wet spec. Brush
Filmthickness (m) Recoating intervals Thinner
56 100 179
Mild steel Area 1
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids %
Version 1
No. 18
Date 7/1/2012
11B ISO 12944-2 category
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Position N/ASubstrate
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CPILOT QD PRIMER, GREY .015" - .021" 150 bar NA NA NA 15 min 26 5 50
PIONER TC, COLOUR .018" - .026" 150 bar NA NA NA 30 min 37 5 50
Page 19 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
4.2 FC 24 h 30 d 10 h 30 d 4 h 30 d 23 0
4.2 FC 24 h 30 d 10 h 30 d 4 h 30 d 23 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible300
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
TANKGUARD STORAGE, RED 63 150 238 P P
TANKGUARD STORAGE, LIGHT RED R
R
63 150 238 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 12B ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 19
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CTANKGUARD STORAGE, LIGHT RED .018" - .027" 150 bar 4 h 20 min 6.5A : 1B 4 h 28 10 50
TANKGUARD STORAGE, RED .018" - .027" 150 bar 4 h 20 min 6.5A : 1B 4 h 28 10 50
Page 20 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
5.4 FC 24 h * 10 h * 4 h * 17 0
5.4 FC 24 h * 10 h * 4 h * 17 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible300
Product Recommended Pot life Induction Time
Mixing Ratio
Volume
NR
BALLOXY HB LIGHT, BEIGE 82 150 183 P P
BALLOXY HB LIGHT, LIGHT GREEN R
R
82 150 183 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 13B ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 20
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max CBALLOXY HB LIGHT, LIGHT GREEN .021" - .031" 150 bar 2 h 10 min 5A : 1B 4 h 35 10 50
BALLOXY HB LIGHT, BEIGE .021" - .031" 150 bar 2 h 10 min 5A : 1B 4 h 35 10 50
Page 21 of 22
-
Technical specification
m
TSR
Min Max Min Max Min Max No. Max %
3.3 FC 30 h 5 d 12 h 5 d 4 h 3 d 0 0
FC:Full Coat R: Recommended NR: Not Recommended P:Possible300
Product Recommended Pot life Induction Time
NRTANKGUARD 412, WHITE R100 300 300 P
10C 23C 40CDry spec. Wet spec. Brush
Location
Roller
Surface Prep. Oil and grease etc. to be removed with a suitable detergent. The entire area to be high pressure fresh water washed at min. 350 bar in order to remove salts and other contamination. When the surface is dry the entire area is to be blast cleaned to min. Sa. 2 (ISO 8501-1:2007).
Type of coat Vol. solids % Filmthickness (m) Recoating intervals Thinner
Position 14B ISO 12944-2 category N/ASubstrate Mild steel Area 1
Version 1
No. 21
Date 7/1/2012
Project EDC Land Rig Prepared by Hamed Mosbah - Jotun Coatings
Product Application Methods
Spray
Customer Approved by
Mixing Ratio
Volume
Dry to touch 23 C Flash Point C
Application RestrictionNozzle Orifice Nozzle Pressure
23 C Min C Max C
6 h 100 10 50TANKGUARD 412, WHITE .021" - .026" 300 bar 1 h 10 min 2A : 1B
Page 22 of 22