U.S. Chemical & Plastics 600 Nova Drive S.E.Massillon, Ohio 44646 U.S.A Toll Free: 1.800.321.0672 www.uschem.com

SS-224

“NOTHING WORKS BETTER AND SANDS EASIER.”Try PRO-GLAZE™ in your shop today.

FEATURES:

★ Maximum Performance Finishing / Blending Putty

★ Advanced Resin Formulation

★ Easy to Apply on Small and Large Areas

★ Excellent Sanding and Featheredging for a Smooth Finish

★ Pinhole Free & Shrink Resistant

★ Stain-Free, Tack-Free and Non-Clog

★ Maximum Adhesion

★ Thinner Viscosity than Icing®

★ Intermixes with PRO-7™ Premium Lightweight Filler,

BASE COAT CLEAR COAT™ and FUZION™

™

EASY SANDING.ULTRA SMOOTH FINISH.

PINHOLE FREE. MAXIMUM ADHESION.

PRO-GLAZE™ Maximum Performance Polyester Finishing Putty is effortless to spread and self-levels to a smooth

easy-to-sand surface that is pinhole free - improving your cycle time. The advanced easy-powder formula

extends the open sanding window time.

TECHNICAL DATA SHEET: PRO-GLAZE™

DESCRIPTION: PRO-GLAZE™ Maximum Performance Polyester Finishing Putty is effortless to spread and self-levels to a smooth easy-to-sand surface that is pinhole free – improving your cycle time. The advanced, easy-powder formula extends the open sanding window time. PRO-GLAZE™ provides excellent results for that invisible repair every time whether over body filler, sand scratches, pinholes, aged OEM topcoats, steel, aluminum, galvanized and other zinc-coated metals, fiberglass and a wide variety of other substrates.

PART NUMBER:•26118 PRO-GLAZE™ 24 fl. oz. tube 6 tubes/case

(11 lbs)

FEATURES / BENEFITS:Feature Benefit Easy sanding, ultra smooth finish High quality repair finish

Pinhole free Quicker to finish, saves time, provides a better finish

Maximum adhesion Superior product versatility

APPROVED SUBSTRATES:• Steel

• Aluminum

• Galvanized and other zinc-coated steel

• Fiberglass • Body filler • Wood

• 1K and 2K primers

• Aged, sanded OEM topcoats

• SMC - can be used for cosmetic repairs. • For structural repairs prone to high • degrees of stress and flexibility, use a SMC • repair product. For flexible plastics use • • • THIN ICE™ 26030.

SURFACE PREPARATION: 1. Clean surface. Remove all dirt, oil, grease and wax with a

cleaning solvent such as 1240-1 Final Prep. 2. Thoroughly dry surface before repairing. 3. Use 80 - 180 grit disc to featheredge to paint for good mechanical adhesion.

MIXING: Place a 4” diameter puddle of putty on clean mixing

surface; we recommend a non-absorbent plastic mixing board. Measure hardener 2% by weight (50 to 1 ratio; add a ribbon of cream hardener from edge to edge across the center of the putty puddle). Puddles larger than 4” in diameter will require additional hardener. Mix thoroughly using a folding motion with a plastic spreader until uniform color is achieved. At room temperature (70-80ºF) approximate setting time is 3-5 minutes.

APPLICATION:1. Using a plastic spreader, apply a thin layer of filler to surface, using firm pressure for maximum adhesion.2. Apply additional layers, building up damaged area higher than the surrounding surface to allow for sanding of the putty. Do not apply over fresh or uncured coatings.

FINISH:When material has hardened, in approximately 15 - 20 minutes, sand with 180 - 220 grit sandpaper followed by 320 - 400 grit if desired prior to priming or sealing. Refer to paint manufacturer’s instructions for topcoat application.

SPECIAL NOTES:When using power equipment, it is recommended that good safety practices be followed: safety glasses with side shields or full face shield, and a respiratory covering to protect from dust. MSA mask part number 459029 with MSA cartridge number 464029. Intermixes with PRO-7™, BC/CC EX™ and FUZION™.

PHYSICAL PROPERTIES:Color: AquaViscosity @ 77°F (Brookfield Model HAT, Spindle T-B/Speed 10): 10,400 - 15,200 cpsWPG: 7.85 lbs/gal (Average)Catalyst Required: Benzoyl PeroxideCatalyzation Ratio: 2% by weight (50:1 ratio)Gel Time @ 77°F: 4 - 6 minutesExotherm Temperature: 210ºF - 230ºFExotherm Peak Time: 10 - 12 minutesTack-Free Time: 8 - 10 minutesSanding Time @ 77ºF: 15 minutesVOC: As packaged = 278 g/LVOC: Applied = 2.2 g/LCorrosion Resistance: ExcellentContents & Caution: See MSDS, available upon request

HEALTH & SAFETY: Read all warnings, first aid and safety for all components before using. Keep out of reach of children and animals. Protect hands with impervious rubber gloves. Wear face, skin and eye protection. USC products are for industrial use by trained professionals only.

MIX

SS-224 (0606)