EART 118 Seismotectonics MWF D250 9:30-10:40 am; Th D250 2:00-4:00 pm Prof.: Thorne Lay, C382 EMS,...
-
Upload
shanon-curtis -
Category
Documents
-
view
212 -
download
0
description
Transcript of EART 118 Seismotectonics MWF D250 9:30-10:40 am; Th D250 2:00-4:00 pm Prof.: Thorne Lay, C382 EMS,...
EART 118 SeismotectonicsMWF D250 9:30-10:40 am; Th D250 2:00-4:00 pm
Prof.: Thorne Lay, C382 E&MS, Office Hours 11:00-12:00 MWFTA: Lingling Ye, Office Hours 11:00-12:00 MF
SEISMOTECTONICS: Study of the relationshipbetween earthquakes, active tectonics, faultsand deformation in a region. Earthquakecharacteristics (location, size/energy release,faulting mechanism) are obtained by analysisof seismic waves recorded by ground motionsensing instruments called seismometers.
Plate boundaries are a planet-wide network of faultswhere most earthquakes and volcanoes are located.
Material is perfectly elastic until it undergoes brittle fracture when applied stress reaches f
Material undergoes plastic deformation when stress exceeds yield stress 0
Permanent strain results from plastic deformation when stress is raised to 0 ‘and
released
Strength increases with depth in the brittle region due to the increasing normal stress, and then decreases with depth in the ductile region due to increasing
temperature. Hence strength is highest at the brittle-ductile transition. Strength decreases rapidly below this transition, so the lithosphere should have little strength
at depths > ~25 km in the continents and 50 km in the oceans.
Strength envelope gives strength vs depth
Shows effects of material, pore pressure, geotherm, strain rate
Brace & Kohlstedt, 1980
BRITTLE
DUCTILE
Earthquake Explanation
• An earthquake is the process of sudden, shearing displacement on a fault (a surface of contact between two rock masses) combined with resultant vibrations (seismic waves)
• Earthquakes ‘catch up’ with prior large-scale crustal motions: strain and stress in rock change (reduce)
• Earthquakes are frictional sliding instabilities. Repeated stick-slip behavior is observed. Friction depends on pressure, temperature, fluids, slip velocity, fault history, and material properties in the fault zone.
Reid, 1910
From Keller & Pinter
SCSCA record section plot of vertical displacements of the Earth's surface recorded by seismometers around the world. Time is on the horizontal axis, and vertical displacements of the Earth on the vertical axis.
Waveforms from the Global Seismographic Network (GSN) of the Sumatra
Earthquake
EARTHQUAKE MAGNITUDE
Earliest measure of earthquake size
Dimensionless number measured various ways, including
ML local magnitudemb body wave magnitudeMs surface wave magnitude Mw moment magnitude
Easy to measure
Empirical - except for Mw, no direct tie to physics of faulting
Note; not dimensionally correct
EARTHQUAKE FREQUENCY - MAGNITUDE
LOG-LINEAR Gutenberg-Richter
RELATION
MOST OF THE LARGEST EARTHQUAKES ARE AT SUBDUCTION ZONES AND RESULT FROM THRUST FAULTING AT THE PLATE INTERFACE
Kanamori, 1978
Much of what is known about the geometry and mechanics of the interaction between plates at subduction zones comes from the distribution and focal mechanisms of shallow earthquakes at the interface between the plates
EARTHQUAKES & TECTONICSLocations map plate boundary zones & regions of intraplate deformation even in underwater or remote areas
Focal mechanisms show strain field
Slip & seismic history show deformation rate
Depths constrain thermo-mechanical structure of lithosphere
PACIFIC
NORTH AMERICA
San Andreas Fault, Carrizo Plain
36 mm/yr
Polarity of first P-wave arrival varies between seismic stations in different directions.
First motion is compression for stations located such that material near the fault moves ``toward'' the station, or dilatation, where motion is ``away from'' the station.
When a P wave arrives at a seismometer from below, a vertical componentseismogram records up or down first motion, corresponding to either compression or dilatation.
P WAVE
FIRST MOTIONS
Seismograms recorded at various distances and azimuths used to study geometry of faulting during an earthquake, known as the focal mechanism.
Use fact that the pattern of radiated seismic waves depends on fault geometry.
Simplest method relies on the first motion, or polarity, of body waves.
More sophisticated techniques use waveforms of body and surface waves.
EARTHQUAKE FOCAL MECHANISM STUDY
Focal mechanisms reveal tectonic faulting orientations:
EARTHQUAKE CYCLE
INTERSEISMIC:
India subducts beneath Burma at about 20 mm/yr
Fault interface is locked
EARTHQUAKE (COSEISMIC):
Fault interface slips, overriding plate rebounds, releasing accumulated motion and generating tsunami HOW OFTEN:
Fault slipped ~ 10 m --> 10000 mm / 20 mm/yr = 500 yrLonger if some slip is aseismic
Faults aren’t exactly periodic, likely because chaotic nature of rupture controls when large earthquakes occur
Stein & Wysession, 2003 4.5-14
INDIA BURMA
Tsunami generated
SUMATRA TRENCH
Focal mechanisms indicate where stick-slip fault sliding occurs. InSubduction Zones, this is mainly thrust faulting on the plate boundary.
Lay et al., EPS, 2011
Aseismic model with near-trench slip can fit GPS statics well.Quasi-seismogeodesy.
Feb. 27, 2010 ChileMw 8.8
Filling the 1835seismic gap?But it went wellbeyond that…
Updated From: Lay et al., GRL, 2010
c
Variable frictional properties seem ubiquitous