INTERNATIONAL ISLAMIC UNIVERSITY

END-OF-SEMESTER EXAMINATION SEMESTER III, 2004/2005 SESSION

KULLIYYAH OF ENGINEERING

Programme : Engineering Level of Study : 1st Time : 2.30 p.m. Date : 18th June, ‘05 Duration : 3 Hrs 00 Min Course Code : MME 1101 Section(s) : 4 (Four) Course Title : Engineering Drawing

This Question Paper consists of 6 (Six) printed pages including the cover page and 5 (Five) questions.

INSTRUCTION(S) TO CANDIDATES

• There are a total of 5 (Five) questions in this paper, answer all of them. • Observe the options given in Q2 and Q3. • Marks are indicated against each question. • Total mark in this question paper is 100.

Any form of cheating or attempt to cheat is a serious offence which may lead to dismissal.

Received by: ____________________________________

____________________________________

Approved by: ____________________________________

2

Q1 [17 marks]

(a) Sketch the symbols for the following electrical/electronic parts. (4 marks)

(i) Tapped with adjustable contact resistor (ii) Loop antenna (iii) Temperature dependent diode (iv) Triode electron tube

(b) Explain the meaning of the symbols shown in Figure 1. Use sketches in your answer. (6 marks)

(i) (ii)

(iii) (iv)

Figure 1

(c) (i) Draw a parabola with a vertical axis and the focus 12 mm from the directrix. Find at least nine points on the curve (including the vertex point). (5 marks)

(ii) Construct a tangent through a point M, which lies at the intersection of the parabola and the line inclined at an angle of 60o to the horizontal and passing through the focus. (1 marks)

(iii) Construct a normal to the parabola at point M. (1 marks)

3

Q2 [20 marks]

The front and the right side views of two objects are shown in Figure 2(i) and Figure 2(ii). Choose one of the two Figures and perform the following:

(a) Draw the given views of the chosen figure (either (i) or (ii)) (4 marks) (b) Add the top view. (10 marks)

(c) Sketch the isometric view of the object. (6 marks)

(Choose any suitable dimension for the object).

(i)

(ii)

Figure 2

4

Q3 [18 marks] The front and right side views of two objects are given in Figure 3(i) and Figure 3(ii). Choose one of the two figures and:

(a) Draw the given views of chosen figure. (4 marks) (b) Add the required auxiliary view of the chosen figure to show the oblique surface in its true shape. (8 marks) (c) Sketch the isometric view of the object. (6 marks)

(Dimensions are in mm.) (i) (ii)

Figure 3

96

16

42

54

R38

R54

48

45o 96

16

42

54 R38

5

Q4 [20 marks] (a) Draw the given views shown in Figure 4. (8 marks) (b) Develop the lateral surface of the cone. (12 marks)

Dimensions are in mm.

Figure 4

Ø 82

38

90

R 28

6

Q5 [25 marks] The components of a C-clamp are shown in Figure 5. The cutting plane of the assembled

components is perpendicular to the direction of arrow A, and passes through the centre of the screw and pin. Based on the given information, perform the following:

(a) Draw the fully assembled top view of the device. (8 marks) (b) Draw the front sectional view of the assembly looking in the direction of the arrow A. (15 marks) (c) Provide the bill of materials. (2 marks) Assume any dimension not given. Dimensions are in millimeters.

A

Figure 5

(Mild Steel)

(Mild Steel)

(Mild Steel)

(Mild Steel)