PosterDigital AMX Tutorial: How to connect your Amx on PosterDigital
DXC-390 / DXC-990 Pan Tilt Solution Sales Manual 8/20/2001 Sony Electronics Inc Visual Imaging...
-
Upload
ezra-rodgers -
Category
Documents
-
view
224 -
download
1
Transcript of DXC-390 / DXC-990 Pan Tilt Solution Sales Manual 8/20/2001 Sony Electronics Inc Visual Imaging...
DXC-390 / DXC-990Pan Tilt Solution
Sales Manual 8/20/2001
Sony Electronics IncVisual Imaging Products
Powered by AMX (Panja)
Our ProspectiveOur Prospective
SONY will provide total solution for Remote camera systemDXC-390 and 990 camerasPan/Tilt head powered by AMXController with CCU function powered by AMX
SONY dealers can sell the system with SONY camerasEasy to make a P/O for dealersTo beat Panasonic AWE series with P/T system
Working with AMXAMX is a great touch panel controller companyThey can customize control software locally
It is impossible for Panasonic
Remote camera system
House of worship HOT Sports shooting Web-casting HOT Distance Learning Board Room Production Videoconference
Target ApplicationTarget Application
Controls up to 6 cameras incl. DXC-390 / 990Color video 6 inches LCD monitor
Can watch video on the monitor
$9520 all set except Camera and lensHigh Speed / Quiet System
45 degree / sec Faster than competitors
High Accuracy5 arc minutes More accurate
Full Remote ControlAbility to control all camera functions by touch screen
Pan / Tilt and Controller SystemPan / Tilt and Controller System
Comparison ChartComparison ChartSONY / Panja Panasonic Fujinon Pro Four
Model Positrack PT10 AW PH300A CPT-1A-10D 1000 RP
Pan/Tilt range(degree)Pan/Tilt speedAccuracy
359 Pan 359 Tilt
45 degree /secLess than +-5 arc
300 Pan 190 Tilt
25 Pan 20 Tilt+-5
300 Pan 190 Tilt
15 degree / sec+-10
350 Pan 180 Tilt
15 Pan 30 Tilt+-20
Controller capablenumber of cameraLoad capacity
Servo systemColor LCDpreviewmonitor
Up to 6 cameras
10lbs
Digital servoYes
Up to 5 cameras
8.8Lbs
AnalogNo
Up to 4 cameras
8.8Lbs
AnalogNo
7.5W
15lbs
AnalogNo
Camera and lenscontrol
Position Preset
Full remote forlens and camera
24 preset for eachcamera
Requiresseparate CCU
10 preset
Requiresseparate CCU
8 preset
Requiresseparate CCU
16 preset
Controller design Ergonomic userfriendly design
Outdated Outdated Outdated
Lens support Canon / FujinonFull support
Limited support Only Fujinon Limited support
List price $9520 $11606 $13680 $10600
PVMMonitorCCMC-12P05/10/25/US
Camera adapterDXC-390/990
Y/C or VBS
Single DXC-390 / 990 under 25mSingle DXC-390 / 990 under 25m
VBS
PT head
Genlock
ControllerMaster controller
CCXC-9DB/US (5m) RGB and VBSCCMC-9DS/US (5m) RGB and Y/C
AMX single head systemPT10-PLV
$9520
Power
Power
AXB-PT10
PS6.5
PS2.8
AXB-EM232
AXP-PLV
AMX Package
CMA-D2
PVMMonitorCMA-D3
Cable extension adapterDXC-390/990
Y/C VBS,RGB and (Component by 990)
Single DXC-390 / 990 under 100mSingle DXC-390 / 990 under 100m
VBS
PT head
Genlock
ControllerMaster controller
AMX single head systemPT10-PLV
$9520
P.S
P.S
CCZ-Axx/us cable
2/5/10/25/50/100m
CCM3MZ
AMX Package
PVMMonitorCCMC-12P05/10/25/US
Camera AdapterDXC-390/990
Y/C or VBS
Dual DXC-390 / 990 under 25mDual DXC-390 / 990 under 25m
VBS
PT head
Genlock
ControllerMaster controller
CCXC-9DBUS (5m) RGB, VBS and (Component by 990) CCMC-9DSUS (5m) RGB, Y/C and (Component by 990)
AMX dual head systemPT10-PLV + PT10-ADD
$9520+$3735xNexcept switcher
DXC-390/990
PT head
SwitcherWe can supply only 2x1 switcher PT10-PRV $700
P.S
P.S
CMA-D2
CMA-D2
PVMMonitorCMA-D3
Cable extension adapterDXC-390/990
Y/C VBS,RGB (Component by 990)
Dual DXC-390 / 990 under 100mDual DXC-390 / 990 under 100m
VBS
PT head
Genlock
Controller
AMX dual head systemPT10-PLV + PT10-ADD + PT10-PRV
$9520+$3735+$700
DXC-390/990
PT head
Switcher
CCZ-Axx/us cable
2/5/10/25/50/100m
CCM3MZ
PT10-PRV
P.S
P.S
P.S
Master controller
CMA-D3
PVMMonitorCMA-D2
Camera adapterDXC-390/990
Y/C VBS
3 to 6 cameras of DXC-390 / 990 under 25m3 to 6 cameras of DXC-390 / 990 under 25m
VBS
PT head
Genlock
Controller
AMX Multi head systemPT10-PLV3PLUS + PT10-ADD
$10655+$3735xNExcept switcher
CMA-D2
DXC-390/990
PT head
Switcher
2/5/10/25m
CMA-D2
CMA-D2
We recommend Extron SW6CVMX
CCMC12PXXUS
P.S
P.S
P.S Axcent3
PVMMonitorCMA-D3
Cable extension adapterDXC-390/990
Y/C VBS,RGB
Up to 6 cameras of DXC-390 / 990 under 100mUp to 6 cameras of DXC-390 / 990 under 100m3 to 6 cameras with CMA-D33 to 6 cameras with CMA-D3
VBS
PT head
Genlock
ControllerAxcent3
AMX Multi head systemPT10-PLV3PLUS + PT10-ADD
$10655+$3735xNExcept switcher
CMA-D3
DXC-390/990
PT head
Switcher
CCZ-A cable
2/5/10/25/50/100m
CCM3MZ
CMA-D3
CMA-D3
We recommend Extron SW6CVMXP.S
P.S
P.S
AMX Packages and accessoriesPackagesPT10PLV Single head system $9520 List Basic Kit
1 P/T head, cables, 1 Controller, 2 AC adapter, 1 System Controller
PT10PLV3PLUS for 3 or more cameras $10655 List1 P/T head, cables, 1 Controller, 2 AC adapter ,1 system controller with 6 RS232C port
AccessoriesPT10ADD Additional P/T head $3735 ListPT10PRV 2x1 switcher $700 ListACRK Accessory Rack Mount Kit $60 ListWMCAM Wall & Ceiling Mount kit $235 ListPMCAM Pedestal Mount Kit $200 ListTMCAM Tri-Pod adapter $45 List
Sony cameras and accessoriesSony cameras and accessories
Camera selectionDXC-390 1/3 inch C mount $2,995DXC-990 1/2 inch Bayonet mount $4,200
Lens selectionDXC3902 cable version
T14X55DA58/F 14x by Fujinon $2,550 ListT10X65SSB/SC 10x by Canon $1,960 List
*Please do not recommend VCL614WEA and 610WEA for AMX system.
Sony cameras and accessoriesSony cameras and accessories
Lens selection
DXC990Single hot shoe
YH18x67KTSA single hot shoe lens by Canon 18x zoom $4,770 ListYH14X73 KTSA single hot shoe lens by Canon 14x zoom $3,720 ListS14x73BWMDD8 single hot shoe lens by Fujinon 14x zoom $3,580 ListYH12X4.8 KTSA Wide Angle Lens by Canon 12X zoom $6,540 List
*Please do not recommend Double Hot Shoe lenses for AMX system.Of course Double hot shoe works well with RM-C950.
Sony cameras and accessoriesSony cameras and accessoriesCamera AdapterCMA-D2 standard camera adapter up to 25m CMA-D3 cable extension adapter up to 100m
Requires CCMC-3MZ cable, and CCZA-XX cableDepends on extension length
*In the case of using CMAD3, you can take RGB, (Component by 990) , VBS and Y/C from rear panel of CMAD3.*In the case of using CMAD2, you can take ONLY Y/C and VBS from rear panel of CMAD2, and but you can take RGB, (Component by 990) and VBS and Y/C directly from rear panel of camera
CablesCMA-D2
CCMC12PXX/US cable
CMA-D3
CCMC-3MZ Junction cable
Package and accessories price for AMX systemPackage and accessories price for AMX systemModel Description Sony MSRP
PT10-PLV Single Camera Pan/Tilt System 9,520.00$ System includes:
1 - AXP-PLV PosiTrack Pilot Video Panel1 - AXB-EM232 Enhanced Master/RS-232 Controller1 - PS2.8 12 VDC, 2.8 A Power Supply (regulated, 110 VAC input)1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to Phoenix)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to 9-pin D-sub1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable
PT10-PLV3plus Multi-Camera Pan/Tilt Systems for CMA-D3 Operation $ 10,655.00$ 1 - AXP-PLV PosiTrack Pilot Video Panel1 - AXCENT3 Integrated Controller1 - PS2.8 12 VDC, 2.8 A Power Supply (regulated, 110 VAC input)1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)6 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to 9-pin D-sub)1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable
PT10-ADD Additional Camera Pan/Tilt 3,735.00$ System includes:
1 - AXB-PT10 PosiTrack 10 Pan/Tilt Head, 10lb (AXlink)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to Phoenix)1 - CC-CAM Camera/Lens Control Cable (8-pin Mini DIN to HD15)1 - PSN6.5 12 VDC, 6.5 A Power Supply (regulated, 110 VAC input)1 - CC-AXL 100' AXlink Cable
PT10-PRV Optional 2x1 Preview Switcher 700.00$ System includes:
1 - AV2SM Auto/Manual Video Switcher (2x1)1 - AXB-REL8 Relay Controller1 - CC-REL
Camera Control Optional ComponentsModel Description Sony MSRP
AC-RK Accessory Rack Kit (3 module capacity, single rack unit height) 60.00$ WM-CAM Wall or Ceiling Mount Adapter for AXB-PT10 235.00$ PM-CAM Pedestal Mount Adapter for AXB-PT10 200.00$ TM-CAM Tripod Mount Adapter for AXB-PT10 45.00$
Ordering Matrix chart 1Ordering Matrix chart 1
Qty Camera Package PT10-PLV PT10-ADD PT10-PLV3+ PT10-PRV1 DXC-390 or 990/CMA-D2 12 DXC-390 or 990/CMA-D2 1 1 Optional3 DXC-390 or 990/CMA-D2 2 1 Extron4 DXC-390 or 990/CMA-D2 3 1 Extron5 DXC-390 or 990/CMA-D2 4 1 Extron6 DXC-390 or 990/CMA-D2 5 1 Extron
1 DXC-390 or 990 /CMA-D3 12 DXC-390 or 990 /CMA-D3 1 1 Optional3 DXC-390 or 990 /CMA-D3 2 1 Extron4 DXC-390 or 990 /CMA-D3 3 1 Extron5 DXC-390 or 990 /CMA-D3 4 1 Extron6 DXC-390 or 990 /CMA-D3 5 1 Extron
Configurations AMX Components
*You can mix up to use DXC-390 and DXC-990
Ordering chart 2Ordering chart 2
Components Model Name PriceCamera DXC-390 $2,995Camera adapter CMA-D2 $252Lens 14x T14X55DA58/F $2,550AMX kit PT10-PLV $9,520Camera cable 5m CCMC-12P05/US $169Wall mount kit WMCAM $235
Total $15,721
One DXC390 standard ordering
Components Model Name PriceCamera DXC-990 $4,200Camera adapter CMA-D2 $252Lens 14x YH14X73KTSA $3,720AMX kit PT10-PLV $9,520Camera cable 5m CCMC-12P05/US $169Wall mount kit WMCAM $235
Total $18,096
One DXC990 standard ordering
Ordering chart 3Ordering chart 3
Components Model Name PriceCamera DXC-390 x 2 $5,990Camera adapter CMA-D2 x 2 $504Lens 14x T14X55DA58/F x 2 $5,100AMX kit PT10-PLV $9,520Additional head PT10-ADD $3,735Camera cable 5m CCMC-12P05/US x2 $338Switcher PT10-PRV $700Wall mount kit WMCAM x 2 $470
Total $26,357
Two DXC390 standard ordering
Components Model Name PriceCamera DXC-990 x 2 $8,400Camera adapter CMA-D2 x 2 $504Lens 14x YH14X73KTSA x2 $7,440AMX kit PT10-PLV $9,520Additional head PT10-ADD $3,735Camera cable 5m CCMC-12P05/US x 2 $338Switcher PT10-PRV $700Wall mount kit WMCAM x 2 $470
Total $31,107
Two DXC990 standard ordering
Ordering chart 4Ordering chart 4
Components Model Name PriceCamera DXC-390 x 3 $8,985Camera adapter CMA-D2 x 3 $756Lens 14x T14X55DA58/F x 3 $7,650AMX kit PT10-PLV3PLUS $10,655Additional head PT10-ADD x 2 $7,470Camera cable 5m CCMC-12P05/US x 3 $507Switcher by Extron SW6CVMX $695Wall mount kit WMCAM x 3 $705
Total $37,423
3 to 6 DXC390 standard ordering
Components Model Name PriceCamera DXC-990 x 3 $12,600Camera adapter CMA-D2 x 3 $756Lens 14x YH14X73KTSA x 3 $11,160AMX kit PT10-PLV3PLUS $10,655Additional head PT10-ADD x 2 $7,470Camera cable 5m CCMC-12P05/US x 3 $507Switcher by Extron SW6CVMX $695Wall mount kit WMCAM x 3 $705
Total $44,548
3 to 6 DXC990 standard ordering
*SONY does not sell Extron Switcher
*SONY does not sell Extron Switcher
*Costs $9,936 for each An additional camera
*Costs $12,311 for each
An additional camera
Ordering chart 5Ordering chart 5
Components Model Name PriceCamera DXC-390 $2,995Camera adapter CMA-D3 $1,520Lens 14x T14X55DA58/F $2,550AMX kit PT10-PLV $9,520Camera cable 50m CCZA50US $1,315Junction cable CCZ3MZ $385Wall mount kit WMCAM $235
Total $18,520
One DXC390 with CMAD3 for cable extension ordering
Components Model Name PriceCamera DXC-990 $4,200Camera adapter CMA-D3 $252Lens 14x YH14X73KTSA $3,720AMX kit PT10-PLV $9,520Camera cable 50m CCZA50US $1,315Junction cable CCZ3MZ $385Wall mount kit WMCAM $235
Total $19,627
One DXC990 with CMAD3 for cable extension ordering
FAQ 1FAQ 1Can we use CMA-D3 for DXC950?
NOCan we use CCU-M5A for this system?
NOHow can we have field supports for the system?
AMX tech support can help you.1-800-932-6993
How can we get longer Axlink cables?Any AMX Dealers will support that.For example Liberty Wire & Cable 1-800-530-89981000' rolls or cut to lengths over 500‘ $0.265 per foot
How long can we extend Axlink cable?Up to 3000 feet including all cables
How can we get 6x1 capables switcher?We would recommend Extron one.
SW6CVMX 60-205-01 $695 list
FAQ 2FAQ 2•Troubleshooting TipsCommon Tech Support Issues (Pan/Tilt Head)Balancing of camera/lens assembly is critical! Improper balancing can cause tilt errors and lockup problems.
On error detection, pan/tilt movement stops (for safety) and will not move until power is cycled. Upon power cycle unit will attempt movement again until another error is detected.
The four slide switches next to the under the circular cover set the lens voltage control mode. All Sony approved lenses are Positional Servo style lenses so all four slide switches must all be set to the left (Auto Position), not to Manual.
The LENS POWER switch toggles +12VDC on pin 1 of the 15 pin D sub connector. All Sony approved lenses get power from the camera so set the LENS POWER switch to the CAM position. If the lens gets power from the camera AND you try to supply power from the PT10, damage may occur.
FAQ 3FAQ 3Lens
Many lenses are not connected to the 15 pin lens port at all and are actually controlled by the camera, which we control via RS232. In these cases the lens control problem is usually an RS232 communication issue between the PT10 and the camera. Check the RS232 cable and restart the Master (AXB-EM232 or Axcent3).
Setup
With multiple camera systems the PT10 Axlink DIP switches must be set to unique values. All AXB-PT10’s are factory set to device 90 which corresponds to camera 1 on the controller. Additional PT10’s should be set sequentially.
Axlink Device Camera Number
90 1
91 2
92 3
93 4
94 5
95 6
Use the DIPSwitch.exe program to reference the correct switch settings. Power must be cycled for changes to take effect.
FAQ 4FAQ 4Problem Possible Cause
No zoom/focus/iris (lens control) If using analog voltage lens control:
•Ensure LENS POWER switch is set to CAM•Ensure lens power switches are all set to the LEFT (Sony only ships Servo Positional style lenses with these systems)If using RS232 camera lens control:
•PT10 must be talking to camera for lens control to work.•Verify camera communication by pressing ‘BARS’ button on panel and looking for color bars from camera. Toggle on and off.•Cycle power on entire system to re-establish communication.•Upgrade to Master Axcess code version 1.56 or later with enhanced Sony communication reliability.•Verify AMX devices are set to 9600 baud.
•On the PT10 switch S2 should have all switches up (on) except switch 7 which should be down (off).•On the EM232 both interface switches (NOT the Program switch) should have all switches down (on) except switch 7 which should be up (off).•Verify DXC camera is set to 9600 baud.
FAQ 5FAQ 5No Focus or Sporadic Focus Movement
•The software version is incompatible with the version of Pilot controller in the system.•Serial numbers beginning with 563070 or 563080 must have a “P” version of software.•Serial numbers beginning with 563050 or 563060 must NOT have a “P” version.
No Pan/Tilt
•Verify Axlink device address (90 – 95)•Verify Axlink LED flashes on PT10
Multiple Heads Pan and Tilt at the Same Time
•Check for duplicate Axlink device ID’s on the PT10’s.
PT10 “Drifts” or Moves by Itself
•Joystick is not calibrated. Reboot the entire system and do not touch the joystick or control knobs during initialization (“Please Wait” screen).
Other issues can be resolved by calling the toll free AMX Technical Support hotline at 800-93AMX93 (800-932-6993).
Software UpgradeSoftware Upgrade
Other issues can be resolved by calling the toll free AMX Technical Support hotline at 800-93AMX93 (800-932-6993).
Software Upgrades AMX will continue to improve performance and features of the system and update in-house inventory. Upgrading your demo unit in the field is a simple procedure that you can perform yourself. Software upgrades are sent as a .zip file from AMX.1. Attach the 9 pin cable to the PC com port and the Master (Axcent3 or EM232).2. Verify all switches on the AXB-EM232 Program switch are down (cycle power if you change them).3. Unzip the files to a directory on your PC.4. Open a dos prompt and go to the directory you unzipped files to.5. type: tokenx /s 1 38400 where 1 is the com port number on the PC.6. Reboot the entire system when it's finished and you should see the new version number on the initial page. Firmware upgrades for the PT10 are also sent as a .zip file.1. Attach the 9 pin cable to the PC com port and the Master (Axcent3 or EM232).2. Unzip the files to a directory on your PC.3. Double click Softrom.exe to start the application.4. Press F1 to set the com port and baud rate. Select 38400 for the baud rate and select the appropriate com port. Press F10 to save settings.5. Press F5 to query on-line devices. This should cause some items to appear on the right side of the screen.6. Press Enter to highlight the firmware file on the left. Press Tab to toggle to the Device side of the screen.7. Locate the AXB-PT10 to be upgraded. It will have a number from 90-95 in the # column and $dc in the Typ column. Press enter to highlight the device.8. Press F4 to program the PT10 with the new firmware.9. When the upgrade is complete press F10 to exit the program.10. Reboot the entire AMX system.
AMX componentsAMX components
AXB-EM232 Enhanced Master ControllerFor 2 or less cameras
The AXB-EM232 Enhanced Master RS-232 Controller is a bus device that provides the features of a system master in a single compact enclosure. It can be used either as a stand-alone device or with other Panja bus devices. The AXB-EM232 runs complete AXCESS programs and allows control of AXlink components as well as control of up to two devices using RS-232 as a control protocol.
Features: Supports RS-232, RS-422, and RS-485 controlled devices, such as switchers and computer-based devices, as well as AXlink devices Supports hardware handshaking and the following asynchronous data communication standards: Baud rates 300; 600; 1,200; 2,400; 4,800; 9,600; 19,200; and 38,400 Data bits 7 or 8, Stop bits 1 or 2, Parity None, Odd, Even, Mark, or Space Includes a 12 VDC power supply Stores program commands in battery-protected memory
AMX componentsAMX components
AXCENT3 Integrated ControllerFor 3 or more cameras
The AXCENT 3 Integrated AXCESS Controller is a multi-port Central Controllers that can be programmed to control RS-232/422/485, relay, IR/serial/data, and input/output devices.
Features 32 front panel status LEDs for AXlink bus operation, RS-232/422/485 (12 LEDs), relay (eight LEDs), IR/serial (six LEDs), and I/O control activity (six LEDs) Six RS-232/422/485 control ports with XON/XOFF LEDs (transmit on/transmit off), and CTS/RTS (clear to send/ready to send), 300–115,200 baud Six IR/serial/data control ports that support IR carrier speeds up to 1.14 MHz, and 1-way data, 300–38,400 baud (0–5 VDC only) Six-channel I/O port for contact closure, 0–5 VDC voltage sensing or inter-active power sensing for IR ports Eight-channel relay port Converts from Master (default) to server operation, allowing use of up to 18 Central Controllers in the same systemAllows system setup, status polling, and diagnostic operations locally, or with a modem, using the Windows-based OpenAXCESS Remote Setup Terminal program
AMX componentsAMX components
The value of the AXB-PT10 PosiTrack 10 can be expressed in three terms—excellent-quality, extreme controllability, and low cost. Supporting camera loads of up to 10 lbs, PosiTrack’s innovative design fuses smooth, quiet motion analog motor drive with precision digital position sensing. Featuring a resolution of over 1 million steps, PosiTrack's digital encoders provide responsive speed control and pinpoint preset accuracy within ±5 arc minutes.
AXB-PT10 Pan/Tilt Head
Features: Supports camera loads of up to 10 pounds (13.6 kg), allows perfect adjustment of H/V center of gravity Integrates onboard control for camera pan/tilt, lens zoom/focus/iris, and RS-232 CCU operation Operates DC-drive lens directly, without need for outboard controllers Stores and recalls presets from internal non-volatile memory Installs upright or upside down (joystick control can be inverted) Limits pan and tilt range using soft stops, programmable on-the-fly from the PosiTrack Pilot Video touch panel Moves with analog DC motor control, positioning sensed via 1 million-step digital encoding Connects to the system via the four-wire AXlink control network over distances up to 3,000 feet using standard twisted-pair wire
AMX componentsAMX components
Features Controls up to 6 PosiTrack 10 Pan/Tilt Heads with Sony DXC-390/DXC-990 cameras, up to 24 presets per camera 6" color-active LCD displays camera video with superimposed touch control graphics On-screen graphics control preset store/recall, camera, and system setup Side-screen buttons (12) instantly select cameras and access control menus Integrated 3-axis joystick controls pan, tilt, and zoom Proportional side-mount wheel controls focus and iris control
AXP-PLV PosiTrack Video Pilot Video Panel
AMX componentsAMX componentsPSN6.5 Power Supply The PSN6.5 supplies power to the AXB-PT10 Pan/Tilt Camera Head
Technical Specifications
DC Power: 12 VDC, 6.5 A output
AC Power: IEC AC cord input for 110/220, 50/60 Hz AC power
Dimensions: 1.5” x 5.5” x 6.4” (HWD) (38mm x 140mm x 164mm)
Weight:: 1.1 lbs. (495 g)
PS2.8 Power SupplyThe PS2.8 supplies power to the system controller and control panel
Technical SpecificationsDC Power: 12 VDC, 2.8 A output
AC Power: IEC AC cord input for 110/220, 50/60 Hz AC power
Dimensions: 5.5” x 3.0” x 1.8” (HWD) (140mm x 76mm x 45mm)
Weight:: 1.5 lbs. (681 g)
AMX componentsAMX components
CC-CAM Connection CablesCC-CAM camera/lens cable connects AXB-PT10 RS-232 control to DXC-390/990 camera head. DB9 (PT10) to 8-pin Mini-DIN (DXC390/990 control input), length – 21 inchesCC-CAM camera/lens cable connects AXB-EM232 RS-232 control to CMA-D3 controllers. 4-pin captive wire Phoenix (EM232) to 8-pin Mini-DIN (CMA-D3), length – 10 feetCC-CAM camera/lens cable connects AXCENT3 RS-232 control to CMA-D3 controller. DB9 (AXCENT3) to 8-pin Mini-DIN (CMA-D3), length – 10 feet
PT10PRV Auto/Manual Video SwitcherFor 2 cameras
Switcher is a media interface device that you can set to automatically or manually switch between two audio and video input sources to one output display monitor. When the internal sync sensor detects a video signal, the AV2SM routes the incoming video and audio signals to the output display monitor connected to the front panel.
Features Two video and audio input source connectors and one output connector Quick connect BNC video connectors
AMX componentsAMX components
The AXB-REL8 Relay Controller provides remote control for up to eight relay functions. Suitable for stand-alone or rack mount applications, the AXB-REL8 may be used with AXCESS or AXCENT systems via the four-wire AXlink data bus.
AXB-REL8 Relay ControllerComes with PT10PRV