DWV PIPE SYSTEMS - viadux.com.au€¦ · grp wrapped dwv sewer bends 27 manhole connections 12...

VIADUX VERSION 1.0

DWV PIPE SYSTEMS

PLASPIPE® DWV PIPE SYSTEMS 32 PRODUCT® NAME

DWV PIPE SYSTEMS OVERVIEWDWV PVC PIPE & FITTINGS DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT APPLICATIONS

Viadux’s PLASPIPE assures our customers of high quality DWV pipe system product which can be used to transport domestic aqueous drain and waste fluids, as well as associated air ventilation. DWV pipe systems are intended for use above and below ground including exposure to direct sunlight. This system is widely known to be economical and lightweight. In addition, DWV PVC is resistant to a wide variety of chemicals, does not support combustion, impermeable to bacteria & fungal attack, and will not corrode. Pipe and fittings assemble easily using either solvent cement (solvent weld joint ”SWJ”) or rubber seal rings (rubber ring joint “RRJ”) to accommodate thermal or ground movement.Viadux’s and their suppliers’ QMS comply to the requirements of ISO 9001:2008.

DWV PIPE & FITTINGS RANGE

•DWV Pipe

-SWJ (Solent Weld Joint)

-RRJ (Rubber Ring Joint)

•DWV Fittings

-SWJ & RRJ fittings

-Cement & Priming Fluid

-Maintenance Shafts & Specialised fittings

Diameter and pipe stiffness range typically available:

DN 100mm-375mm

SN 4-10 in SWJ; SN 8 in RRJ

All comply with AS/NZS 1260 ̶ PVC-U Pipes and Fittings for Drain, Waste and Vent Application

INSTALLATION

Installation should be made with reference to:

AS/NZS3500 National Plumping Standard

AS/NZS2032 Installation of PVC Pipe Systems

Relevant guidelines available from PIPA (www.pipa.com.au/technical) include:

POP102 Solvent Cement Jointing of PVC Pipe

POP103 Depth Of Engagement For PVC Pipes

POP014 Assessment of Polyethylene Welds

This publication has been prepared by Viadux Pty Ltd (Viadux) to assist in the selection of Viadux’s products. This publication is not, and is not intended to be, an exhaustive statement on pipeline design, installation or technical matters. Any conclusions, formulae and other such information contained in this publication are for guidance purposes only. They are based on assumptions which will not be correct for every project, design or installation.

Successful design or installation depends on numerous factors outside Viadux’s control, including site conditions, site preparation and installation workmanship. Prior to the use of any information in this publication, it is the Users responsibility to verify all such information and to confirm the suitability of any products selected for their intended purpose. Viadux makes no representation or warranty in this regard. Users of this publication must rely on their own knowledge, skill and judgement, particularly with reference to the qualities and suitability of the products and conditions surrounding each specific design or installation. To the extent permitted by law, Viadux accepts no liability for any loss or damage, howsoever incurred, by any person who relies on the whole or any part of this publication. To the extent permitted by law, Viadux excludes all liability imposed by any statute or by the general law in respect of this publication whether statements and representation in this publication are made negligently or otherwise.

All information and intellectual property relating to this publication (including but not limited to patents, designs, drawings, instructions, specifications, circuit drawings, componentry, trade secrets, trade marks and copyright in such information and intellectual property (Proprietary Information) and all right, title and interest therein) are the sole property of or licensed by Viadux and Users of this publication gain no right, title or interest in the Proprietary Information whatsoever.

This publication must not be copied or reproduced in whole or in part without Viadux’s prior written consent. This publication is and shall remain Viadux’s property and shall be immediately returned to Viadux’s on its request. Viadux reserves the right to make changes to any aspect of this publication at any time without notice.

The publication is not an offer to trade. This note is an integral part of this publication.

PLASPIPE DWV PIPE SYSTEMS CONTENTDWV PVC PIPE & FITTINGS DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT APPLICATIONS

04DWV PIPE SWJ (SOLVENT WELD JOINT)

13REFLUX VALVES

23RILEY JUNCTIONS

13FLAP VALVES (FROG FLAPS)

22“C” TYPE DWV SEWER JUNCTIONS

07LOBSTER BENDS

14STUB FLANGES

25COUPLING (STRAIGHT, SLIP, ACCESS)

10CAPS (PUSH-ON, THREADED, ACCESS)

16BENDS (ELBOWS)

26VERTICAL BACKDROP ASSEMBLIES

12LEVEL INVERT TAPERS

20JUNCTIONS

04DWV PIPE RRJ (RUBBER RING JOINT)

24JUNCTIONS SANDED

08JUNCTIONS

14ACCESS BENDS (BACK, SIDE)

26LEVEL INVERT TAPERS

11BOLTED TRAP SCREWS

19GRP WRAPPED DWV SEWER BENDS

27MANHOLE CONNECTIONS

12COUPLINGS (STRAIGHT, SLAB REPAIR, SLIP)

22GRP WRAPPED DWV SEWER JUNCTIONS

05BENDS (ELBOWS)

14BOUNDARY TRAPS

24DROP JUNCTIONS (DROP TEES)

09TAPPING SADDLES

15EW ADAPTORS (SOCKET, SPIGOT)

26DWV INSERT FITTINGS

11INSPECTION OPENINGS

19LONG SWEEP BENDS (ELBOWS)

28INSPECTION OPENINGS

29PVC PIPE CEMENT & PRIMING FLUID

04

05

16

30

31

DWV PIPE

DWV FITTINGS SWJ(SOLVENT WELD JOINT)

DWV FITTINGS RRJ (RUBBER RING JOINT)

SPECIALISED FITTINGS

GLOSSARY OF TERMS

4 PLASPIPE® DWV PIPE SYSTEMS PLASPIPE® DWV PIPE SYSTEMS 5

DWV FITTINGS SWJ (SOLVENT WELD JOINT)BENDS (ELBOWS)DWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

DWV PVC PIPE SYSTEMSDWV PIPES SWJ (SOLVENT WELD JOINT) & RRJ (RUBBER RING JOINT)DWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

DWV PIPE SWJ

CODE SIZE (mm) DESCRIPTION LENGTH CRATE QTY

R22.4060.100.6S 100 DWV (SC) PIPE SWJ - SN 6 6M 67






R22.4040.225.6S 225 DWV PIPE SWJ - SN 4 6M 12






* SC = Sandwich Construction

DWV PIPE RRJ

CODE SIZE (mm) DESCRIPTION LENGTH CRATE QTY

R23.4080.150.3R 150 DWV (SC) PIPE - SN 8 3M 28

R22.4080.150.6R 150 DWV (SC) PIPE - SN 8 6M 28

R22.4080.225.3R 225 DWV PIPE - SN 8 3M 12

R22.4080.225.6R 225 DWV PIPE - SN 8 6M 12

R22.4080.300.3R 300 DWV PIPE - SN 8 3M 6

R22.4080.300.6R 300 DWV PIPE - SN 8 6M 6

R22.4080.375.3R 375 DWV PIPE - SN 8 3M 6

R22.4080.375.6R 375 DWV PIPE - SN 8 6M 6

5º BENDS SWJ F&F

CODE SIZE (mm) DESCRIPTION PACK QTY

R22.100511.100 100 DWV 100 BEND 5º F&F SWJ (M) 40

R22.100511.150 150 DWV 150 BEND 5º F&F SWJ 12

R22.100511.225 225 DWV 225 BEND 5º F&F SWJ 1

R22.100511.300 300 DWV 300 BEND 5º F&F SWJ 1

R22.100511.375 375 DWV 375 BEND 5º F&F SWJ 1

15º BENDS SWJ F&F



R22.101511.150 150 DWV 150 BEND 15º F&F SWJ 12


R22.101511.300 300 DWV 300 BEND 15º F&F SWJ 1

R22.101511.375 375 DWV 375 BEND 15º F&F SWJ 1

22º BENDS SWJ F&F


R22.102211.150 150 DWV 150 BEND 22º F&F SWJ 12

R22.102211.225 225 DWV 225 BEND 22º F&F SWJ 1

R22.102211.300 300 DWV 300 BEND 22º F&F SWJ 1

R22.102211.375 375 DWV 375 BEND 22º F&F SWJ 1

30º BENDS SWJ F&F



R22.103011.150 150 DWV 150 BEND 30º F&F SWJ 18

R22.103011.225 225 DWV 225 BEND 30º F&F SWJ 1

R22.103011.300 300 DWV 300 BEND 30º F&F SWJ 1

R22.103011.375 375 DWV 375 BEND 30º F&F SWJ 1


DWV FITTINGS SWJ (SOLVENT WELD JOINT)BENDS (ELBOWS) CONTINUEDDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º BENDS SWJ F&F






R22.104511.375 375 DWV 375 BEND 45º F&F SWJ 1

60º BENDS SWJ F&F



R22.106011.150 150 DWV 150 BEND 60º F&F SWJ 12

R22.106011.225 225 DWV 225 BEND 60º F&F SWJ 1

R22.106011.300 300 DWV 300 BEND 60º F&F SWJ 1

R22.106011.375 375 DWV 375 BEND 60º F&F SWJ 1

88/90º BENDS SWJ F&F




R22.109011.225 225 DWV 225 BEND 88/90º F&F SWJ (M) 4

R22.109011.300 300 DWV 300 BEND 88/90º F&F SWJ (M) 1

R22.108811.375 375 DWV 375 BEND 88º F&F SWJ 1

DWV FITTINGS SWJ (SOLVENT WELD JOINT)LOBSTER BENDSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º LOBSTER BENDS SWJ


R22.154511.375 375 DWV 375 LOBSTER BEND 45º F&F SWJ 1











DWV FITTINGS SWJ (SOLVENT WELD JOINT)JUNCTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º JUNCTIONS SWJ F&F


R22.204511.100 100 DWV 100 JUNCT EQU 45º F&F SWJ (M) 13


R22.214511.1510 150X100 DWV 150X100 JUNCT RED 45º F&F SWJ (M) 8








R22.204511.375 375 DWV 375 JUNCT EQU 45º F&F SWJ 1

R22.214511.3730 375X300 DWV 375X300 JUNCT RED 45º F&F SWJ 1




90º JUNCTIONS SWJ F&F

















DWV FITTINGS SWJ (SOLVENT WELD JOINT)TAPPING SADDLESDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º TAPPING SADDLES SWJ


R22.814501.100 100 DWV 100 SADDLE EQU 45º SWJ 1


R22.804501.1510 150X100 DWV 150X100 SADDLE RED 45º SWJ (M) 1





R22.804501.3022 300X225 DWV 300X225 SADDLE RED 45º SWJ 1












90º TAPPING SADDLES SWJ


















DWV FITTINGS SWJ (SOLVENT WELD JOINT)CAPSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

CAPS PUSH-ON SWJ


R22.500001.100 100 DWV 100 CAP PUSH SWJ (M) 100




R22.500001.375 375 DWV 375 CAP PUSH SWJ 1

CAPS THREADED


R22.500003.100 100 DWV 100 CAP THREADED (M) 50




ACCESS CAPS SWJ F


R22.430001.100 100 DWV 100 ACCESS COUP W/CAP F SWJ (M) 1



R22.430001.225L 225 DWV 225 ACCESS COUP W/LOCK CAP F SWJ (M) 1

R22.430001.300L 300 DWV 300 ACCESS COUP W/LOCK CAP F SWJ (M) 1

R22.430001.ACP N/A DWV ACCESS CAP SPANNER 1

DWV FITTINGS SWJ (SOLVENT WELD JOINT)BOLTED TRAP SCREWS + INSPECTION OPENINGSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

BOLTED TRAP SCREWS SWJ F


R22.950000.100 100 DWV 100 BOLTED TRAP SCREW 60





INSPECTION OPENINGS 90º WITH THREADED CAP SWJ F&F


R22.330011.150 150 DWV 150 INSPECT OPEN EQU W/CAP F&F SWJ (M) 1

R22.330011.225 225 DWV 225 INSPECT OPEN EQU W/CAP F&F SWJ (M) 1

R22.330011.225 225X150 DWV 225X150 INSPECT OPEN W/CAP F&F SWJ (M) 1

R22.330011.2210 225X100 DWV 225X100 INSPECT OPEN W/CAP F&F SWJ (M) 1

R22.330011.3022 300X225 DWV 300X225 INSPECT OPEN W/CAP F&F SWJ 1

R22.330011.3015 300X150 DWV 300X150 INSPECT OPEN W/CAP F&F SWJ 1

INSPECTION OPENING NO CAP SWJ F&F


R22.350011.225 225 DWV 225 INSPECT OPEN NO CAP F&F SWJ (M) 1




DWV FITTINGS SWJ (SOLVENT WELD JOINT)FLAP VALVES + REFLUX VALVESDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

DWV FITTINGS SWJ (SOLVENT WELD JOINT)LEVEL INVERT TAPERS + COUPLINGSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

LEVEL INVERT TAPERS (REDUCERS) SWJ M&F


R22.600021.1510 150X100 DWV 150X100 LIT M&F SWJ (M) 1






R22.600021.3730 375X300 DWV 375X300 LIT M&F SWJ 1

R22.600021.3722 375X225 DWV 375X225 LIT M&F SWJ 1

R22.600021.3715 375X150 DWV 375X150 LIT M&F SWJ 1

R22.600021.3710 375X100 DWV 375X100 LIT M&F SWJ 4

Note: Major diameter is a spigot & minor diameter is a socket.

STRAIGHT COUPLING SWJ F&F


R22.400011.100 100 DWV 100 COUPLING F&F SWJ (M) 50

R22.400011.150 150 DWV 150 COUPLING F&F SWJ 20




SLAB REPAIR COUPLING SWJ F&F


R22.440012.100 100 DWV 100 REPAIR COUP F&F SWJ (M) 1

R22.440012.150 150 DWV 150 REPAIR COUP F&F SWJ (M) 10

R22.440012.300 300 DWV 300 REPAIR COUP F&F SWJ 3

R22.440012.375 375 DWV 375 REPAIR COUP F&F SWJ 3

Note: Internal spigot at one end & spigot at the other end.

SLIP COUPLING SWJ F&F


R22.420001.100 100 DWV 100 SLIP COUPLING SWJ 1





FLAP VALVES (FROG FLAPS) SWJ F


R22.970011.100 100 DWV 100 FLAP VALVE (M) 1

R22.970011.100Z 100 DWV 100 FLAP VALVE - MOZZIE (M) 1

R22.970011.150 150 DWV 150 FLAP VALVE (M) 1


R22.970011.225 225 DWV 225 FLAP VALVE (M) 1


R22.970011.300 300 DWV 300 FLAP VALVE (M) 1


R22.970011.375 375 DWV 375 FLAP VALVE 1

REFLUX VALVES SWJ F&F


R22.980021.100 100 DWV 100 REFLUX VALVE F&F SWJ 1






DWV FITTINGS SWJ (SOLVENT WELD JOINT)BOUNDARY TRAPS + STUB FLANGES + ACCESS BENDSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

BOUNDARY TRAPS SWJ F&F


R22.960011.100 100 DWV 100 BOUNDARY TRAP F&F SWJ 14




STUB FLANGES SWJ F


R12.135.100 100 DWV 100 STUB FLANGE F SWJ 10





88º SIDE BACK ACCESS BENDS SWJ F&F


R22.148811.100 100 DWV 100 BEND B/ACCESS 88º F&F SWJ (M) 1

SIDE ACCESS BENDS SWJ F&F


R22.134511.100 100 DWV 100 BEND S/ACCESS 45º F&F SWJ (M) 1

R22.138811.100 100 DWV 100 BEND S/ACCESS 88º F&F SWJ (M) 1

DWV FITTINGS SWJ (SOLVENT WELD JOINT)EW ADAPTORSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

EW SOCKET ADAPTORS


R22.930000.100 100 DWV 100 EW SOCK ADAPTORS 1




EW SPIGOT ADAPTORS


R22.940000.100 100 DWV 100 EW SPIG ADAPTORS 1





DWV FITTINGS RRJ (RUBBER RING JOINT)BENDS (ELBOWS)DWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

5º BENDS RRJ F&F


R22.100512.300 300 DWV 300 BEND 5º F&F RRJ 1

15º BENDS RRJ F&F


R22.101512.100 100 DWV 100 BEND 15º F&F RRJ 1

R22.101512.150 150 DWV 150 BEND 15º F&F RRJ 1

R22.101512.225 225 DWV 225 BEND 15º F&F RRJ 1

R22.101512.300 300 DWV 300 BEND 15º F&F RRJ 1

30º BENDS RRJ F&F


R22.103012.100 100 DWV 100 BEND 30º F&F RRJ 1

R22.103012.150 150 DWV 150 BEND 30º F&F RRJ 1

R22.103012.150 225 DWV 225 BEND 30º F&F RRJ 1

R22.103012.150 300 DWV 300 BEND 30º F&F RRJ 1

45º BENDS RRJ F&F


R22.104512.100 100 DWV 100 BEND 45º F&F RRJ 1

R22.104512.150 150 DWV 150 BEND 45º F&F RRJ 1

R22.104512.225 225 DWV 225 BEND 45º F&F RRJ 1

R22.104512.300 300 DWV 300 BEND 45º F&F RRJ 1

60º BENDS RRJ F&F


R22.106012.100 100 DWV 100 BEND 60º F&F RRJ 1

R22.106012.150 150 DWV 150 BEND 60º F&F RRJ 1

R22.106012.225 225 DWV 225 BEND 60º F&F RRJ 1

R22.106012.300 300 DWV 300 BEND 60º F&F RRJ 1

DWV FITTINGS RRJ (RUBBER RING JOINT)BENDS (ELBOWS) CONTINUEDDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

88º BENDS RRJ F&F


R22.108812.100 100 DWV BEND PLAIN 88º F&F RRJ 100 1




15º BENDS RRJ M&F


R22.101522.100F 100 DWV 100 BEND 15º M&F RRJ (FAB) 12




30º BENDS RRJ M&F






45º BENDS RRJ M&F






60º BENDS RRJ M&F


R22.106022.100 100 DWV 100 BEND 60º M&F RRJ 1

R22.106022.150 150 DWV 150 BEND 60º M&F RRJ 1

R22.106022.225 225 DWV 225 BEND 60º M&F RRJ 1

R22.106022.300 300 DWV 300 BEND 60º M&F RRJ 1


DWV FITTINGS RRJ (RUBBER RING JOINT)BENDS (ELBOWS) CONTINUEDDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

DWV FITTINGS RRJ (RUBBER RING JOINT)GRP WRAPPED + LONG SWEEP DWV SEWER BENDS DWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

GRP WRAPPED DWV SEWER BENDS RRJ M&F


R22.111522.100 100 DWV 100 GRP D/SEWER BEND 15º M&F RRJ 1





LONG SWEEP 635MM RADIUS BENDS RRJ F&F


R22.188812.150 150 DWV 150 BEND 635MM RAD 88º F&F RRJ 1

R22.188822.150 150 DWV 150 BEND 635MM RAD 88º M&F RRJ 1

LONG SWEEP 3M RADIUS BENDS RRJ M&F


R22.160522.150 150 DWV 150 BEND 3M RAD 5º M&F RRJ 1








88º BENDS RRJ M&F


R22.108822.100 100 DWV 100 BEND 88º M&F RRJ 3

R22.108822.150 150 DWV 150 BEND 88º M&F RRJ 5

R22.108822.225 225 DWV 225 BEND 88º M&F RRJ 1

R22.108822.300 300 DWV 300 BEND 88º M&F RRJ 1


DWV FITTINGS RRJ (RUBBER RING JOINT)JUNCTIONS CONTINUEDDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º JUNCTIONS RRJ M&F


R22.204522.100F 100 DWV 100 JUNCT EQU 45º M&F RRJ (FAB) 1


R22.214422.1510 150X100 DWV 150X100 JUNCT RED 45º M&F RRJ 1







88º JUNCTIONS RRJ M&F


R22.208822.100 100 DWV 100 JUNCT EQU 88º M&F RRJ 1







DWV FITTINGS RRJ (RUBBER RING JOINT)JUNCTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

45º JUNCTIONS RRJ F&F


R22.204512.100 100 DWV JUNCTION EQU 45º F&F RRJ 100 1


R22.214512.1510 150X100 DWV JUNCTION RED 45º F&F RRJ 150 X 100 1









88º JUNCTIONS RRJ F&F


R22.208812.100 100 DWV 100 JUNCT EQU 88º F&F RRJ 1


R22.218812.1510 150X100 DWV 150X100 JUNCT RED 88º F&F RRJ 1






JUNCTIONS EQUAL RRJ WITH SWJ BRANCH & CAP F&F


R22.204514.150 150 DWV 150 JUNCT EQ 45º SWJ BR & CAP F&F RRJ 1

R22.208814.150 150 DWV 150 JUNCT EQ 88º SWJ BR & CAP F&F RRJ 1


DWV FITTINGS RRJ (RUBBER RING JOINT)RILEY JUNCTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

RILEY JUNCTIONS RRJ F&F


R22.298812.100 100 DWV 100 RILEY JUNCT EQU F&F RRJ 1


R22.308812.1510 150X100 DWV 150X100 RILEY JUNCT RED F&F RRJ 1






RILEY JUNCTIONS WITH SWJ BRANCH RRJ F&F


R22.298814.100 100 DWV 100 RILEY JUNCT EQU W/SWJ BRANCH F&F RRJ 1


R22.308814.1510 150X100 DWV 150X100 RILEY JUNCT RED W/SWJ BRANCH F&F RRJ 1


R22.308814.2215 225X150 DWV 225X150 RILEY JUNCT RED W/SWJ BRANCH F&F RR 1






RILEY JUNCTIONS RRJ M&F


R22.298822.100 100 DWV 100 RILEY JUNCT EQU M&F RRJ 1


R22.308822.1510 150X100 DWV 150X100 RILEY JUNCT RED M&F RRJ 1







DWV FITTINGS RRJ (RUBBER RING JOINT)GRP WRAPPED + “C” TYPE DWV SEWER JUNCTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

GRP WRAPPED DWV SEWER JUNCTIONS RRJ F&F


R22.288812.100 100 DWV 100 GRP D/SEWER JUNCT 88º F&F RRJ 1



R22.364512.1510 150X100 DWV 150X100 GRP D/SEWER JUNCT RED 45º F&F RRJ 1






GRP WRAPPED DWV SEWER JUNCTIONS RRJ M&F


R22.288822.100 100 DWV 100 GRP D/SEWER JUNCT 88º M&F RRJ 1


R22.368822.1510 150X100 DWV 150X100 GRP D/SEWER JUNCT 88º M&F RRJ 1




“C” TYPE DWV SEWER JUNCTIONS RRJ


R22.374512.100 100 DWV 100 GRP D/SEWER JUNCT TYPE C RRJ 1

R22.459012.100 100 DWV 100 JUNCT TYPE "C" 90º W/CAP RRJ 1

R22.374512.150 150 DWV 150 GRP D/SEWER JUNCT TYPE C RRJ 1


DWV FITTINGS RRJ (RUBBER RING JOINT)COUPLINGSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONSZ

COUPLINGS RRJ


R22.400012.100 100 DWV 100 COUPLING F&F RRJ 1




SLIP COUPLINGS RRJ


R22.420002.100F 100 DWV 100 SLIP COUPLING F&F RRJ (FAB) 1




ACCESS COUPLINGS WITH CAP RRJ


R22.430020.100 100 DWV 100 ACCESS COUP M&F W/CAP RRJ 100 1



DWV FITTINGS RRJ (RUBBER RING JOINT)JUNCTIONS SANDED + DROP JUNCTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

JUNCTIONS SANDED RRJ M&F


R22.798812.150 150 DWV 150 JUNCT EQU 88º SAND M&F RRJ 1

DROP JUNCTIONS RRJ M&F


R22.324562.150 150 DWV 150 DROP JUNCT 45º M&F&M RRJ 1






DWV FITTINGS RRJ (RUBBER RING JOINT)MANHOLE CONNECTIONSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

MANHOLE SOCKET SANDED RRJ M&F


R22.720022.100 100 DWV 100 M/HOLE SOCK SANDED SN10 M&F RRJ 0.5M 12






MANHOLE SPIGOT SANDED RRJ M&M


R22.750030.100 100 DWV 100 M/HOLE SPIG SANDED SN10 M&M RRJ 0.5M 12





MANHOLE SOCKET UNSANDED RRJ M&F


R22.760022.100 100 DWV 100 M/HOLE SOCK UNSANDED SN10 M&F RRJ 0.5M 12






MANHOLE DROP BENDS RRJ


R22.788812.100 100 DWV 100 M/HOLE DROP BEND SAND 88º M&F RRJ 1

R22.788812.150 150 DWV 150 M/HOLE DROP BEND SAND 88º M&F RRJ 1

DWV FITTINGS RRJ (RUBBER RING JOINT)LEVEL INVERT TAPERS + DWV INSERT FITTINGS + VERTICAL BACKDROP ASSEMBLIESDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

LEVEL INVERT TAPERS RRJ M&F


R22.600022.2210 225X100 DWV 225X100 LIT M&F RRJ 2

R22.600022.2215 225X150 DWV 225X150 LIT M&F RRJ 2

R22.600022.3730 375X300 DWV 375X300 LIT M&F RRJ (BWN) 18

R22.600122.1510 150X100 DWV 150X100 LIT M&F RRJ 1

R22.600122.2210 225X100 DWV 225X100 LIT M&F RRJ 1

R22.600122.2215 225X150 DWV 225X150 LIT M&F RRJ 1

R22.600122.3022 300X225 DWV 300X225 LIT M&F RRJ 1

R22.600122.3010 300X100 DWV 300X100 LIT M&F RRJ 1

R22.600122.3015 300X150 DWV 300X150 LIT M&F RRJ 1

DWV INSERT FITTINGS RRJ


R22.700020.100 100 100 INSERT R/R FITTING DWV 25



VERTICAL BACKDROP ASSEMBLIES RRJ M&F


R22.900002.100 100 DWV 100 VERTICAL B/DROP ASS M&F RRJ 1




PVC PIPE CEMENT – PRESSURE TYPE P

CODE SIZE DESCRIPTION BOX

R12.461.012P 125ml PVC PIPE CEMENT TYPE P GREEN 36



R12.461.050PC 500ml PVC CEMENT TYPE P CLR GREEN 24

R12.461.100P 1ltr PVC PIPE CEMENT TYPE P GREEN 12

R12.461.400P 4ltr PVC PIPE CEMENT TYPE P GREEN 4

R12.461.400PC 4ltr PVC PIPE CEMENT TYPE P CLR GREEN 4

PVC PIPE CEMENT – PRESSURE LARGE BORE GAP FILLING


R12.461.100G 1ltr PVC PIPE CEMENT TYPE G CLEAR 6

R12.461.400G 4ltr PVC PIPE CEMENT TYPE G CLEAR 4

PVC PIPE CEMENT – NON PRESSURE TYPE N


R12.461.050N 500ml PVC PIPE CEMENT TYPE N BLUE 24

R12.461.050NC 500ml PVC PIPE CEMENT TYPE N CLEAR 24

R12.461.100N 1ltr PVC PIPE CEMENT TYPE N BLUE 12

R12.461.400N 4ltr PVC PIPE CEMENT TYPE N BLUE 4

R12.461.400NC 4ltr PVC PIPE CEMENT TYPE N CLEAR 12

PVC PRIMING FLUID


R12.463.012 125ml PVC PRIMING FLUID RED 36



R12.463.050C 500ml PVC PRIMING FLUID CLEAR 24

R12.463.100 1ltr PVC PRIMING FLUID RED 12

R12.463.400 4ltr PVC PRIMING FLUID RED 4

PVC PIPE CEMENT & PRIMING FLUID PVC-M PIPE CEMENTS & PRIMING FLUIDS ARE DESIGNED AND MANUFACTURED TO AS/NZS 3879 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

DWV FITTINGS RRJ (RUBBER RING JOINT)INSPECTION OPENINGSDWV FITTINGS ARE DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT (DWV) APPLICATIONS

INSPECTION OPENINGS WITH CAP RRJ F&F


R22.330012.100 100 DWV 100 INSPECT OPEN W/CAP F&F RRJ 1

R22.330012.150 150 DWV 150 INSPECT OPEN W/CAP F&F RRJ 1

INSPECTION OPENINGS WITH CAP RRJ M&F


R22.330022.100 100 DWV 100 INSPECT OPEN W/CAP M&F RRJ 1



INSPECTION OPENINGS WITH 2 CAPS F&F


R22.340014.100 100 DWV 100 INSPECT OPEN W/2XCAP F&F RRJ/SWJ 1




30 PLASPIPE® DWV PIPE SYSTEMS

AS/NZ 1260:2009

Australian/New Zealand Standard.PVC-U pipes and fittings for drain waste and vent applications.

AS/NZS 4999:2006 PVC-U maintenance shafts

ATS 5200.006-2005

Australian Technical Specifications Technical specification for plumbing and drainage products.

Branch Take Off, Junction

DN Diameter Nominal

DWV Drain Waste Vent, Sewer

EW Earthen Ware, Clay Pipe

F&F Female Socket and Female Socket, F+F

GRP Glass Reinforced Pipe

IO Inspection Opening

ISO9001: 2008 Quality Management System

LIT Level Invert Taper, Reducer

LTS Locking Trap Screw

M/m Metres

MM/mm Millimetres

M&F Male Spigot and Female Socket, M+F

M&M Male Spigot and Male Spigot, M+M

RRJ Rubber Ring Joint

SWJ Solvent Weld Joint, Solvent Cement Joint (SCJ)

SN Stiffness, Nominal

Socket Female, F

Spigot Male, M

TAC Threaded Access Cap

UPVC Unplasticised Poly Vinyl Chloride (also uPVC, PVCU)

WSAA Water Services Association of Australia

° Degrees (Angle)

GLOSSARY OF TERMSPLASPIPE DWV PIPE SYSTEMS

PLASPIPE® DWV PIPE SYSTEMS 31

SPECIALISED DWV FITTINGSMAINTENANCE SHAFTS & SPECIAL FABRICATIONSDWV PVC PIPE & FITTINGS DESIGNED AND MANUFACTURED TO AS/NZS 1260 FOR DRAIN, WASTE & VENT APPLICATIONS

MAINTENANCE SHAFTS

Viadux supplies an extensive range of fully moulded and fabricated configurations, typically available in DN 150, 225 or 300mm as: Inline (straight), Terminal Elbow, Elbows (15, 22, 30, 60 & 90°) & Junctions (45°, 90° & Riser).

PVC Maintenance Shafts are designed for easy passage of camera and cleaning equipment. Where approved, they replace traditional manholes for faster and easier sewer system installs. Viadux ensures that their range of Maintenance Shaft systems are manufactured to the requirements of AS/NZS 4999; and appraised by the Water Services Association of Australia (WSAA). All major water boards have approved this system across Australia.

SPECIAL FABRICATIONS

Viadux can also provide fabricated custom-made fittings, from Down Pipe Adaptors to complex Junctions. If the DWV fitting you are looking for is not listed in this catalogue or you would like to learn more about the latest product innovations available, just ask your Viadux representative and they will be delighted to assist you.

ADELAIDEP: 08 8340 3411F: 08 8340 3422E: [email protected]

BRISBANEP: 07 5589 4400F: 07 5534 7079E: [email protected]

DARWINP: 08 8935 3300F: 08 8947 3981E: [email protected]

GOLD COASTP: 07 5589 4400F: 07 5534 7079E: [email protected]

MELBOURNEP: 03 9309 9133F: 03 9309 6237E: [email protected]

SYDNEYP: 02 9794 3440F: 02 9794 3499E: [email protected]

NEWCASTLEP: 02 4914 0700 F: 02 4966 8776 E: [email protected]

PERTHP: 08 9346 8500F: 08 9346 8501E: [email protected]

SYDNEYP: 02 9794 3440 F: 02 9794 3499E: [email protected]

TOWNSVILLEP: 07 4725 5940F: 07 4725 4995E: [email protected]

CUSTOMER CENTRES

PROJECT OFFICE

VIADUX WATER NETWORK SYSTEMS

PO BOX 141 FAIRFIELD, NEW SOUTH WALES 1860 / VIADUX.COM.AU

PHONE 02 9794 3400 AUSTRALIA

All Viadux trademarks and logos are owned by Viadux Pty. Ltd. All other brand or product manes are trademarks or registered marks of their respective owners. Because we are continuously improving our products and services, Viadux reserves the right to change specifications without prior notice.

DWV PIPE SYSTEMS

DWV PIPE SYSTEMS - viadux.com.au€¦ · grp wrapped dwv sewer bends 27 manhole connections 12...

Documents

Transcript of DWV PIPE SYSTEMS - viadux.com.au€¦ · grp wrapped dwv sewer bends 27 manhole connections 12...